Search
Filters
total: 507
Search results for: CMOS ANALOGUE CIRCUITS
-
Low-Voltage LDO Regulator Based on Native MOS Transistor with Improved PSR and Fast Response
PublicationIn this paper, a low-voltage low-dropout analog regulator (ALDO) based on a native n-channel MOS transistor is proposed. Application of the native transistor with the threshold voltage close to zero allows elimination of the charge pump in low-voltage regulators using the pass element in a common drain configuration. Such a native pass transistor configuration allows simplification of regulator design and improved performance,...
-
Starter for Voltage Boost Converter to Harvest Thermoelectric Energy for Body-Worn Sensors
PublicationThis paper examines the suitability of selected configurations of ultra-low voltage (ULV) oscilla-tors as starters for a voltage boost converter to harvest energy from a thermoelectric generator (TEG). Important properties of particularly promising configurations, suitable for on-chip imple-mentation are compared. On this basis, an improved oscillator with a low startup voltage and a high output voltage swing is proposed. The applicability...
-
Assessment of the Accuracy of Determining the Angular Position of the Unmanned Bathymetric Surveying Vehicle Based on the Sea Horizon Image
PublicationThe paper presents the results of research on assessing the accuracy of angular position measurement relative to the sea horizon using a camera mounted on an unmanned bathymetric surveying vehicle of the Unmanned Surface Vehicle (USV) or Unmanned Aerial Vehicle (UAV) type. The first part of the article presents the essence of the problem. The rules of taking the angular position of the vehicle into account in bathymetric surveys...
-
Control of the wind turbine generator
PublicationWind power system consists of two main parts: wind turbine and electrical generator. Wind turbine converts the energy of the flowing air into mechanical energy, next generator converts this energy into electrical energy that is sent to the power system. These two processes should be realized with maximum efficiency and the following requirements for the control system can be formulated: opti-mal wind power conversion, compensation...
-
Application of infrared thermoography to non-contact testing of varistors
PublicationTesting of varistors using thermography was carried out in order to assess their protective properties against possible overvoltage phenomena in the form of high-level voltage surges. An advantage of the thermography technique is non-contact temperature measurement. It was proposed to assess the properties of varistors workingin electronic devices as protective elements, on the basis of estimating temperature increments on varist...
-
Local-Global Space Mapping for Rapid EM-Driven Design of Compact RF Structures
PublicationIn this work, we introduce a robust and efficient technique for rapid design of compact RF circuits. Our approach exploits two-level space mapping (SM) correction of an equivalent circuit model of the structure under design. The first SM layer (local correction) is utilized to ensure good matching between the equivalent circuit and the electromagnetic model at the component level. On the other hand, the global correction allows...
-
COMPARISON OF SYSTEM ON CHIP TECHNOLOGIES FOR SPACE APPLICATIONS
PublicationThe paper presents a review of technologies available for the implementation of digital and mixed signal systems, particularly the system on a chip (SoC) for space applications. The phenomena encountered in the space environment are briefly presented, together with the known solutions, regarding the design of complex electronic systems. The most important norms regarding single die integrated circuits designed for space are also...
-
Study of oxygen electrode reactions on symmetrical porous SrTi0.30Fe0.70O3-δ electrodes on Ce0.8Gd0.2O1.9 electrolyte at 800 °C–500 °C
PublicationIron doped strontium titanates (SrTi1-xFexO3-δ) are an interesting mixed ionic-electronic conductor model used to study basic oxygen reduction/oxidation reactions. In this work, we performed an impedance spectroscopy study on symmetrical porous SrTi0.30Fe0.70O3-δ (STF70) electrodes on a ceriabased electrolyte. The sample was measured in varying oxygen concentration: from 0.3% to 100% in 800 °C - 500 °C temperature range. Low polarisation...
-
Zero-Pole Approach in Microwave Passive Circuit Design
PublicationIn this thesis, optimization strategies for design of microwave passive structures including filters, couplers, antenna and impedance transformer and construction of various surroogate models utilized to fasten the design proces have been discussed. Direct and hybrid optimization methodologies including space mapping and multilevel algorithms combined with various surrogate models at different levels of fidelity have been utilized...
-
Calculations of material factors for a set of 20 thermistors
Open Research DataThe presented data set is part of the research aimed at determining the actual characteristics of each thermistor in a package of twenty NTC10k type sensors.
-
Expedite EM-driven generation of Pareto-optimal trade-off curves for variable-turn on-chip inductors
PublicationThis work presents a novel approach to computationally efficient Pareto front identification for variable-turn on-chip inductors. The final outcome is a set of solutions that correspond to the best trade-offs between conflicting design objectives. Here, we consider minimising inductor area and, simultaneously, maximising its quality factor, while maintaining a specified inductance value at a given operating frequency. As opposed...
-
Dynamic range comparison of voltage-mode and current-mode state-space Gm-Cbiquad filters in reciprocal structures
PublicationW pracy dokonano porównania zakresu dynamicznego bikwadratowych filtrówGm-C zmiennych stanu, których struktury układowe oparte są na zasadzie tran-sformacji układu dołączonego. Przeprowadzono rozważania teoretyczne w wynikuktórych określono ogóne formuły zakresu dynamicznego dla klasy filtrów Gm-Ctrybu napięciowego i prądowego. Weryfikacja rezultatów teoretycznych byłazrealizowana za pomocą symulatora SPICE.
-
Design and Optimization of Metamaterial-Based 5G Millimeter Wave Antenna for Gain Enhancement
PublicationIn this brief, a low profile, broadband, high-gain antenna array based on optimized metamaterials (MMs) with dual-beam radiation is reported for 5G millimeters wave (mm-wave) applications. The design is a simple bow tie operating at a 5G band of 28 GHz. It consists of two bow ties with substrate integrated waveguide (SIW)-based power splitter. A broad impedance bandwidth of 26.3−29.8 GHz is obtained by appropriately combining the...
-
Frequency-Reconfigurable Hybrid SIW-Based Self-Diplexing Antenna Using Solid and Liquid Dielectric Loading
PublicationThis paper presents a novel frequencyreconfigurable self-diplexing antenna (SDA) utilizing a hybrid substrate-integrated waveguide (SIW). The antenna comprises a radiating slot, a feeding network, and a hybrid SIW cavity featuring half-mode circular and half-mode rectangular SIW structures. The unique feature of this antenna lies in its fine-tuning capability of each resonant frequency by inserting or injecting solid and liquid...
-
Miniaturized Dual-Band Bandpass Filter with Wide Inter Stopband for 5G Applications
PublicationThis article presents the design of a miniaturized dual-band bandpass filter with a wide inter-stopband and improved isolation. A novel topology comprising the series connection of shunt cascaded coupled lines and quarter-wavelength open stubs is proposed to realize the dual-band filter along with half-wavelength stepped-impedance stubs. The circuit characteristics contain nine transmission zeros and four poles. The transmission...
-
A Simplified SPWM Scheme for a Compact 3-Level Dual-Output Inverter
PublicationSinusoidal Pulse-width modulation, SPWM, is inverter-leg-based, logical-operation-based, and lesscomputational-intensive. In this brief, these simplifying features of SPWM are extended to the control of the 10-switch, 3-level inverter. The control strategy is based on the single triangular carrier SPWM perspective. Procedures and details of the sharing of four-common power switches by the 3 inverter legs are given. Classically,...
-
A Five-Leg Three-Level Dual-Output Inverter
PublicationClassical 3-level dual-output inverter, 3-L DOI, involves two similar 3-level inverters that provides a pair of 3-phase output voltages with same or different frequencies from common input voltage source. Flexibility of either operation of the constituting inverters is evident in this DOI; but total duplication of power switches is a major drawback. State of the art coupled 3-L DOIs reduce this drawback by providing series-shared...
-
Shielded HMSIW-Based Self-Triplexing Antenna With High Isolation for WiFi/WLAN/ISM Band
PublicationThis article presents a novel design of a miniaturized self-triplexing antenna (STA) based on the shielded half-mode substrate integrated waveguide (S-HMSIW) for WiFi/WLAN/ISM-band applications. The S-HMSIW is constructed by assembling one row of vias and an open slot at the open-ended side of the conventional HMSIW. This configuration increases the quality factor and minimizes unwanted radiation loss, which allows for achieving...
-
RF Multi-Functional Input-Reflectionless Dispersive-Delay Structure With Sharp-Rejection Filtering Using Channelization Techniques
PublicationA class of RF multi-functional input-reflectionless dispersive-delay structure (DDS) with linear-type in-band groupdelay variation and sharp-rejection bandpass-filtering capability is reported. It exploits a two-branch-channelized/balanced-type circuit with similar low-order reflective DDS units inside its channels, which are connected through input/output 3-dB quadrature wideband couplers. The adopted DDS unit is based on a coupledresonator...
-
Microfluidic SIW-Based Tunable Self-Diplexing Antenna for Sub-6 GHz Band Applications
PublicationThis work introduces a novel frequency tunable self-diplexing antenna (SDA) design based on substrate integrated waveguide (SIW) technology. A modified A-shaped slot is employed on the cavity’s top plane, which is excited by two independent 50 Ω microstrip feed lines to operate at each resonant frequency. The frequency flexibility of the proposed antenna allows for fine-tuning at each resonance frequency. The frequency flexibility...
-
A Compact Self-Hexaplexing Antenna Implemented on Substrate-Integrated Rectangular Cavity for Hexa-Band Applications
PublicationThis brief introduces a novel architecture of a compact self-hexaplexing antenna (SHA) implemented on a substrate-integrated rectangular cavity (SIRC) for hexa-band applications. The proposed SHA is configured by using an SIRC resonator, two Pi-shaped slots (PSSs), and six 50Ω microstrip feedlines. The PSSs are connected back-to-back and loaded on top of the SIRC resonator to produce six patch radiators (PRs). The PRs are excited...
-
A complex variable fractional-delay FIR filter structure
PublicationW artykule wprowadzamy strukturę zespolonego filtru o skończonej odpowiedzi impulsowej (ang. finite impulse response - FIR) ze zmiennym opóźnieniem ułamkowym (ang. fractional delay - FD). Strukturę tę otrzymujemy na podstawie przestrajanego filtru FD FIR o współczynnikach rzeczywistych. Stanowi ona połączenie zbioru liniowo-fazowych filtrów FIR o współczynnikach stałych rzeczywistych i dwóch łańcuchów mnożąco-akumulujących, zawierających...
-
A fractionally delaying complex Hilbert transform filter
PublicationPrzedstawiono nowy, dyskretno-czasowy, ułamkowo-opóźniający (FD od ang. fractional delayor), zespolony filtr Hilberta (HTF od ang. Hilbert transform filter) nazwany FDHTF. Filtr ten jest oparty na parze obróconych filtrów o zmiennym opóźnieniu ułamkowym (VFD od ang. variable fractional delayor). Za pomocą filtru FDHTF realizuje się jednocześnie filtrację Hilberta i wprowadzanie ułamkowego opóźnienia do przetwarzanego sygnału. Dzięki...
-
Two-Rate Based Low-Complexity Variable Fractional-Delay FIR Filter Structures
PublicationThis paper considers two-rate based structures for variable fractional-delay (VFD) finite-length impulse response (FIR) filters. They are single-rate structures but derived through a two-rate approach. The basic structure considered hitherto utilizes a regular half-band (HB) linear-phase filter and the Farrow structure with linear-phase subfilters. Especially for wide-band specifications, this structure is computationally efficient...
-
Inline Microwave Filters With N+1 Transmission Zeros Generated by Frequency-Variant Couplings: Coupling-Matrix-Based Synthesis and Design
PublicationA general coupling-matrix-based synthesis methodology for inline Nth-order microwave bandpass filters (BPFs) with frequency-variant reactive-type couplings that generate N+1 transmission zeros (TZs) is presented in this brief. The proposed approach exploits the formulation of the synthesis problem as three inverse nonlinear eigenvalue problems (INEVPs) so that the coupling matrix is built from their sets of eigenvalues. For this...
-
A Power-Efficient Digital Technique for Gain and Offset Correction in Slope ADCs
PublicationIn this brief, a power-efficient digital technique for gain and offset correction in slope analog-to-digital converters (ADCs) has been proposed. The technique is especially useful for imaging arrays with massively parallel image acquisition where simultaneous compensation of dark signal non-uniformity (DSNU) as well as photo-response non-uniformity (PRNU) is critical. The presented approach is based on stopping the ADC clock by...
-
Compact, Order Extensible and Wide-Stopband Bandpass Filter Based on SIW Cavity with Rectangular Ring Slot
PublicationThis article introduces novel architectures of bandpass filters (BPFs) using a substrate integrated waveguide (SIW) cavity with a rectangular ring slot (RRS) for compact size, extensible order, and broad stopband responses. Two bandpass filters, which demonstrate a second-and a fourth-order Chebyshev response, respectively, are realized by employing identical cavities with RRS, without increasing the physical size of the circuit....
-
An Efficient PEEC-Based Method for Full-Wave Analysis of Microstrip Structures
PublicationThis article introduces an efficient method for the equivalent circuit characterization and full-wave analysis of microstrip structures, leveraging the full-wave partial element equivalent circuit (PEEC). In particular, the multilayered Green's function is evaluated using the discrete complex-image method (DCIM) and employed to establish the mixed potential integral equations. The proposed strategy considers time delays for the...
-
Diagnostyka uszkodzeń analogowych układów elektronicznych z zastosowaniem specjalizowanej sieci neuronowej
PublicationNa tle trendów rozwojowych diagnostyki analogowych układów elektronicznych AEC (Analog Electronic Circuits), przedstawiono nową metodę diagnostyki uszkodzeń parametrycznych układów analogowych, ze specjalizowanym klasyfikatorem neuronowym, o zwiększonej odporności na tolerancje elementów układu i niepewności pomiaru. Zastosowano specjalizowaną sieć neuronową z dwucentrowymi funkcjami bazowymi TCRBF (Two-center Radial Basis Function),...
-
Modeling of Common Mode Currents Induced by Motor Cable in Converter Fed AC Motor Drives
PublicationInvestigation of conducted EMI generation in AC motor fed by pulse width modulated frequency converters requires to consider parasitic capacitances in converters, motor windings and feeding cables to be taken into account. Motor voltage transients and related common mode currents are significantly correlated with resonance effects occurring in load circuits. An analysis of frequency converter load impedance-frequency characteristics...
-
Development of a compact microstrip resonant cell aimed at efficient microwave component size reduction
PublicationA comprehensive comparison of a wide collection of compact microstrip resonant cells (CMRCs) found in the extensive body of literature has been presented. The evaluation of different CMRC designs has led to the selection of the most promising CMRC geometry for the efficient miniaturisation of modern microwave components. In order to showcase the vital effectiveness of the approach, the initially selected CMRC has been notably...
-
Analysis of AC/DC/DC Converter Modules for Direct Current Fast-Charging Applications
PublicationThe paper is a comprehensive laboratory comparison study of two galvanic isolated solution off-board battery chargers: (1) Si-based cost-effective case, and (2) SiC-bidirectional ready for vehicle to grid concept case. All circuits are modular, and in both cases the DC/DC converter can be replaced according to the end user requirements (the coupled transformer remains the same and is constructed based on 12xC100 cores to avoid...
-
Fluconazole resistant Candida auris clinical isolates have increased levels of cell wall chitin and increased susceptibility to a glucosamine-6-phosphate synthase inhibitor
PublicationIn 2009 Candida auris was first isolated as fungal pathogen of human disease from ear canal of a patient in Japan. In less than a decade, this pathogen has rapidly spread around the world and has now become a major health challenge that is of particular concern because many strains are resistant to multiple class of antifungal drugs. The lack of available antifungals and rapid increase of this fungal pathogen provides an incentive...
-
Diminshed toxicity of C-1748, 4-methyl-9-hydroxyethylamino-1-nitroacridine, compared with its demethyl analog, C-857, corresponds to its resistance to metabolism in HepG2 cells
PublicationThe narrow "therapeutic window" of anti-tumour therapy may be the result of drug metabolism leading to the activation or detoxification of antitumour agents. The aim of this work is to examine (i) whether the diminished toxicity of a potent antitumour drug, C-1748, 9-(2'-hydroxyethylamino)-4-methyl-1-nitroacridine, compared with its 4-demethyl analogue, C-857, results from the differences between the metabolic pathways for the...
-
Antibiotic-Based Conjugates Containing Antimicrobial HLopt2 Peptide: Design, Synthesis, Antimicrobial and Cytotoxic Activities
PublicationRecent studies have shown that modified human lactoferrin 20−31 fragment, named HLopt2, possesses antibacterial and antifungal activity. Thus, we decided to synthesize and evaluate the biological activity of a series of conjugates based on this peptide and one of the antimicrobials with proven antibacterial (ciprofloxacin, CIP, and levofloxacin, LVX) or antifungal (fluconazole, FLC) activity. The drugs were covalently connected...
-
TRANSFER OF ELECTRIC ENERGY [2023/24]
e-Learning CoursesCourse content: Basic information on the structure of the power system, the major devices (components) for generation, transmission and distribution of electricity. Active and reactive power generation and their sources. Power supply networks. Tasks, structure, parameters. AC and DC transmission of electricity. Equivalent diagrams of the components of the power system. Steady state load flow calculation: currents, voltage,...
-
TRANSFER OF ELECTRIC ENERGY [2022/23]
e-Learning CoursesCourse content: Basic information on the structure of the power system, the major devices (components) for generation, transmission and distribution of electricity. Active and reactive power generation and their sources. Power supply networks. Tasks, structure, parameters. AC and DC transmission of electricity. Equivalent diagrams of the components of the power system. Steady state load flow calculation: currents, voltage,...
-
TRANSFER OF ELECTRIC ENERGY [2024/25]
e-Learning CoursesCourse content: Basic information on the structure of the power system, the major devices (components) for generation, transmission and distribution of electricity. Active and reactive power generation and their sources. Power supply networks. Tasks, structure, parameters. AC and DC transmission of electricity. Equivalent diagrams of the components of the power system. Steady state load flow calculation: currents, voltage, power,...
-
TRANSFER OF ELECTRIC ENERGY [2024/25]
e-Learning CoursesCourse content: Basic information on the structure of the power system, the major devices (components) for generation, transmission and distribution of electricity. Active and reactive power generation and their sources. Power supply networks. Tasks, structure, parameters. AC and DC transmission of electricity. Equivalent diagrams of the components of the power system. Steady state load flow calculation: currents, voltage,...
-
Calculations of the resistance values of 20 thermistors at 100°C
Open Research DataThe presented data set is part of the research aimed at determining the actual characteristics of each thermistor in a package of twenty NTC10k type sensors.
-
Calculations of the resistance values of 20 thermistors at 50°C
Open Research DataThe presented data set is part of the research aimed at determining the actual characteristics of each thermistor in a package of twenty NTC10k type sensors.
-
AI-powered Digital Transformation: Tools, Benefits and Challenges for Marketers – Case Study of LPP
PublicationThe article aims to show the role (benefits and challenges) of AI-powered digital marketing tools for marketers in the age of digital transformation. The considerations were related to the Polish market and a case study of LPP, a Polish clothing retailer. The starting point for this study was the analysis of the literature on the concept of artificial intelligence (AI) with reference to digital marketing. In the next steps, the...
-
Rapid simulation-driven design of miniaturised dual-band microwave couplers by means of adaptive response scaling
PublicationOne of the major challenges in the design of compact microwave structures is the necessity of simultaneous handling of several objectives and the fact that expensive electromagnetic (EM) analysis is required for their reliable evaluation. Design of multi-band circuits where performance requirements are to be satisfied for several frequencies at the same time is even more difficult. In this work, a computationally efficient design...
-
Rapid multi-criterial design of microwave components with robustness analysis by means of knowledge-based surrogates
PublicationManufacturing tolerances and uncertainties concerning material parameters, e.g., operating conditions or substrate permittivity are detrimental to characteristics of microwave components. The knowledge of relations between acceptable parameter deviations (not leading to violation of design specifications) and the nominal performance (not considering uncertainties), and is therefore indispensable. This paper proposes a multi-objective...
-
Shaking table experimental study on damage mechanism of the disconnecting switch under seismic excitation
PublicationThe efficiency of the energetic network is a very import safety issue in the region experienced by the earthquake. High voltage disconnecting switches are important elements of the energetic infrastructure used to separate electric circuits (i.e. during repairs), which should not be damaged remaining fully operational. The aim of the paper is to show the results of the shaking table experimental investigation focused on damage...
-
Design of a Patch Power Divider with Simple Structure and Ultra-Broadband Harmonics Suppression
PublicationThis paper introduces a simple H-shaped patch Wilkinson power divider (WPD), which provides ultra wide harmonics suppression band. The presented WPD designed at 1.8 GHz, and exhibits good performance at the operating bandwidth. In the proposed divider structure, two simple patch low-pass filters (LPFs) are employed at each branch, and three open ended stubs are added at each port. The proposed divider, implemented using the aforementioned...
-
Design specification management with automated decision-making for reliable optimization of miniaturized microwave components
PublicationThe employment of numerical optimization techniques for parameter tuning of microwave components has nowadays become a commonplace. In pursuit of reliability, it is most often carried out at the level of full-wave electromagnetic (EM) simulation models, incurring considerable computational expenses. In the case of miniaturized microstrip circuits, densely arranged layouts with strong cross-coupling effects make EM-driven tuning...
-
Globalized parametric optimization of microwave components by means of response features and inverse metamodels
PublicationSimulation-based optimization of geometry parameters is an inherent and important stage of microwave design process. To ensure reliability, the optimization process is normally carried out using full-wave electromagnetic (EM) simulation tools, which entails significant computational overhead. This becomes a serious bottleneck especially if global search is required (e.g., design of miniaturized structures, dimension scaling over...
-
Calculations of the resistance values of 20 thermistors at 0°C
Open Research DataThe presented data set is part of the research aimed at determining the actual characteristics of each thermistor in a package of twenty NTC10k type sensors.
-
Activation of endogenous regenerative potential in mammals using epigenetic inhibitor zebularine
PublicationIn this work, a nucleoside inhibitor of DNA methyltransferases, zebularine, was investigated as a wound healing and regeneration promoting agent. It was found that a high dose of intraperitoneally delivered zebularine improved punch wound closure in the ear pinna in mice. Both cytidine, a zebularine analogue, and uridine, a zebularine metabolite, did not promote ear pinna hole closure. The effect of zebularine on ear pinna healing...