Search
Filters
total: 2133
displaying 1000 best results Help
Search results for: GEOMETRIC WORKING VOLUME
-
Geometric working volume of a satellite positive displacement machine
PublicationThis article describes a method for determining the geometric working volume of satellite positive displacement machines (pump and motor). The working mechanism of these machines is satellite mechanism consisting of two non-circular gears (rotor and curvature) and circular gears (satellites). Two variants of the satellite mechanism are presented. In the first mechanism, the rolling line of the rotor is a sinusoid "wrapped" around...
-
The influence of pressure drop on the working volume of a hydraulic motor
PublicationReliability and maintenance analysis of hydraulic positive machines basicly focused on the processes of their wear and failure. But in order to correctly assess the mechanical and volumetric efficiency of a hydraulic motor, both at the stage of development research or at the stage of control tests during its exploitation, the working volume of this motor must be correctly determined. Therefore this paper proposes a new method of...
-
Determination of the theoretical and actual working volume of a hydraulic motor
PublicationA new methodology of determination of the theoretical and actual working volume of a hydraulic motor based on the characteristics of the delivered flow rate into hydraulic motor vs. the rotational speed at a constant pressure drop in the working chambers is described in this paper. A new method of describing the delivered flow rate into a motor per one shaft revolution as a nonlinear function of the pressure drop in the motor working...
-
Volume efficiency loss in axial pumps caused by working fluid compressibility.
PublicationPrzedstawiono teoretyczną analizę wpływu ściśliwości cieczy roboczej konstrukcji mechanizmu rozrządu pompy wielotłoczkowej osiowej na straty energetyczne w przestrzeni martwej. Podano wyniki uzyskane dla typowych konstrukcji.
-
Determination of the Theoretical and Actual Working Volume of a Hydraulic Motor—Part II (The Method Based on the Characteristics of Effective Absorbency of the Motor)
Publication: In this article, the second method of determination of the theoretical and actual working volume of a hydraulic motor is described. The proposed new method is based on the characteristics of effective absorbency of the motor. The effective absorbency has been defined as the ratio of flow rate in a motor to the rotational speed of the motor’s shaft. It has been shown that the effective absorbency is a nonlinear function of the...
-
The impact of footing conditions of a vertical-axis floating-roof tank on structural shell deformation
PublicationStructural shells of fuel tanks are often subjected to geometric imperfections which may lead to exceeding the ultimate and serviceability limit states. One of the means triggering shell deformation is non-uniform settlement caused by incoherent soil conditions. Analysis carried out in the work concerns of vertical-axis, floating-roof cylindrical shell which volume is 50.000 m3, founded on a complex multi-layered soil. The sensitivity...
-
The electrical properties mesurements of SOFC with Ce0.9Co0.1O2-s functional layer
Open Research DataThe dataset includes the electrical properties mesurements of SOFC with Ce0.9Co0.1O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
-
The electrical properties mesurements of SOFC with Ce0.8Co0.1Cu0.1O2-s functional layer
Open Research DataThe dataset includes the electrical properties mesurements of SOFC with Ce0.8Co0.1Cu0.1O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
-
The electrical properties mesurements of SOFC with Ce0.8Co0.15Cu0.05O2-s functional layer
Open Research DataThe dataset includes the electrical properties mesurements of SOFC with Ce0.8Co0.15Cu0.05O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
-
The electrical properties mesurements of SOFC with Ce0.9Cu0.1O2-s functional layer
Open Research DataThe dataset includes the electrical properties mesurements of SOFC with Ce0.9Cu0.1O2-s layer. Samples were produced using aqueous soft chemistry methods (microemulsion method) and applied in form of a layer onto the anode of the commercial SOFC. The SOFC was working under biogas feeding at 750oC. The layers were sintered at 1100oC.
-
Reduced-cost surrogate modelling of compact microwave components by two-level kriging interpolation
PublicationFull-wave electromagnetic (EM) analysis is a versatile tool for evaluating the performance of high-frequency components. Its potential drawback is its high computational cost, inhibiting the execution of EM-driven tasks requiring massive simulations. The applicability of equivalent network models is limited owing to the topological complexity of compact microstrip components because of EM cross-coupling effects. Development of...
-
The electrochemical response to BDD electrode functionalization with CD147 receptor
Open Research DataThis dataset contains the results of the electrochemical impedance spectroscopy (EIS) measurements of the boron-doped diamond (BDD) electrode functionalization with CD147 receptor. The functionalized electrode was then used for the electrochemical detection of the SARS-CoV-2 virus S1 protein.
-
The electrochemical response to BDD electrode functionalization with ACE2 receptor
Open Research DataThis dataset contains the results of the electrochemical impedance spectroscopy (EIS) measurements of the boron-doped diamond (BDD) electrode functionalization with ACE2 receptor. The functionalized electrode was then used for the electrochemical detection of the SARS-CoV-2 virus S1 protein.
-
The electrochemical response to BDD electrode functionalization with IgG2B receptor
Open Research DataThis dataset contains the results of the electrochemical impedance spectroscopy (EIS) measurements of the boron-doped diamond (BDD) electrode functionalization with IgG2B receptor. The functionalized electrode was then used for the electrochemical detection of the SARS-CoV-2 virus S1 protein.
-
Measures of Functional Reliability of Two-Lane Highways
PublicationRural two-lane highways are the most common road type both in Poland and globally. In terms of kilometres, their length is by far greater than that of motorways and expressways. They are roads of one carriageway for each direction, which makes the overtaking of slower vehicles possible only when there is a gap in the stream of traffic moving from the opposite direction. Motorways and express roads are dual carriageways that are...
-
Teleportation of geometric structures in 3D
PublicationThe simplest quantum teleportation algorithms can be represented in geometric terms in spaces of dimensions 3 (for real state vectors) and 4 (for complex state vectors). The geometric representation is based on geometric-algebra coding, a geometric alternative to the tensor-product coding typical of quantum mechanics. We discuss all the elementary ingredients of the geometric version of the algorithm: geometric analogs of states...
-
Fracture Surface Behavior of 34CrNiMo6 High-Strength Steel Bars with Blind Holes under Bending-Torsion Fatigue
PublicationThe present study evaluates the fracture surface response of fatigued 34CrNiMo6 steel bars with transverse blind holes subjected to bending with torsion loading. The analysis of the geometric product specification was performed by means of height parameters Sx, functional volume parameters Vx, and fractal dimension Df. Surface topography measurements were carried out using an optical profilometer with focus variation technology....
-
Geometric analogue of holographic reduced representation
PublicationHolographic reduced representations (HRRs) are distributed representations of cognitive structuresbased on superpositions of convolution-bound n-tuples. Restricting HRRs to n-tuples consisting of 1,one reinterprets the variable binding as a representation of the additive group of binary n-tupleswith addition modulo 2. Since convolutions are not defined for vectors, the HRRs cannot be directlyassociated with geometric structures....
-
NUMERYCZNE MODELOWANIE HYDRODYNAMIKI JAKO NARZĘDZIE WSPOMAGANIA PROJEKTOWANIA REKREACYJNYCH I SPORTOWYCH OBIEKTÓW WODNYCH
PublicationW artykule opisano zastosowanie obliczeń numerycznych w procesie projektowania, analizy działania oraz oceny bezpieczeństwa użytkowania wodnych obiektów rekreacyjnych i sportowych. Użytkownicy aquaparków, sportowcy, a szczególnie kibice, oczekują wyjątkowych doznań na obiektach wodnych z jednoczesną gwarancją bezpieczeństwa. Na te kwestie duży wpływ ma hydrodynamika przepływu. Aby właściwie dobrać parametry geometryczne i hydrauliczne...
-
Geometric Algebra Model of Distributed Representations
PublicationFormalism based on GA is an alternative to distributed representation models developed so far-Smolensky's tensor product, Holographic Reduced Representations (HRR) and Binary Spatter Code (BSC). Convolutions are replaced by geometric products, interpretable in terms of geometry which seems to be the most natural language for visualization of higher concepts. This paper recalls the main ideas behind the GA model and investigates...
-
A new concept of PWM duty cycle computation using the Barycentric Coordinates in a Three-Dimensional voltage vectors arrangement
PublicationThe paper presents a novel approach to the Pulse Width Modulation (PWM) duty cycle computing for complex or irregular voltage vector arrangements in the two (2D) and three–dimensional (3D) Cartesian coordinate systems. The given vectors arrangement can be built using at least three vectors or collections with variable number of involved vectors (i.e. virtual vectors). Graphically, these vectors form a convex figure, in particular,...
-
Distributed Representations Based on Geometric Algebra: the Continuous Model
PublicationAuthors revise the concept of a distributed representation of data as well as two previously developed models: Holographic Reduced Representation (HRR) and Binary Spatter Codes (BSC). A Geometric Analogue (GAc - ''c'' stands for continuous as opposed to its discrete version) of HRR is introduced - it employs role-filler binding based on geometric products. Atomic objects are real-valued vectors in n-dimensional Euclidean space...
-
Analytical method of modelling the geometric system of communication route
PublicationThe paper presents a new analytical approach to modelling the curvature of a communication route by making use of differential equations. The method makes it possible to identify both linear and nonlinear curvature. It enables us to join curves of the same or opposite signs of curvature. Solutions of problems for linear change of curvature and selected variants of nonlinear curvature in polynomial and trigonometric form were analyzed....
-
Computations of critical load value of composite shell with random geometric imperfections
PublicationThe work presents the numerical analysis of composite shell with geometric imperfections subjected to compression along its generatrix. The imperfections are described as single indentations and random fields with random parameters of shape and correlation. The fields are generated with the use of the authors made program. Using the authors’ FEM software as well as commercial package Femap with NX Nastran, the critical load values...
-
Calculation of an ultimate load value of a silo with geometric imperfections in the shape of eigenforms
PublicationThe ultimate load value of a silo with initial geometric imperfections was measured. The structure was loaded with wind. Imperfections were assumed as translations of the shell nodes from perfect geometry taken from eigenforms and their combinations. Two variants of the maximum deflection placement with respect to the direction of wind pressure were proposed. The first consists in applying the maximum wind pressure to the element...
-
Analysis and Evaluation of the Working Cycle of the Diesel Engine
PublicationThe paper presents a proposal to apply a quantitative evaluation of the diesel engine with regard to the phenomena occurring during of a working cycle. The proposed procedure when analyzing test results from diesel engine is an attempt to transfer an engine activity evaluation methods in the operational time scale (exploit time), eg. in hours, to the micro-scale (dynamic time) relating only to the execution time of one (several)...
-
Analytical progress on symmetric geometric discord: Measurement-based upper bounds
PublicationQuantum correlations may be measured by means of the distance of the state to the subclass ofstates having well defined classical properties. In particular, a geometric measure of asymmetricdiscord [Daki´c et al., Phys. Rev. Lett. 105, 190502 (2010)] was recently defined as the Hilbert-Schmidt distance of a given two-qubit state to the closest classical-quantum (CQ) correlated state.We analyze a geometric measure of symmetric...
-
ANALYSIS OF THE PUNCHING FAILURE MECHANISM IN WORKING PLATFORMS
PublicationPaper presents an analysis of the shear failure mechanism which occurs from the punching of a working platform layer in relation to its thickness, grain size arrangement and mechanical properties, taking into consideration the interaction with soft subgrade. The study is based on the observations of performance of natural scale structures (Streefkerk) and the results of model investigations numerically represented with the use...
-
Safety of erection and repair of steel tanks with geometric imperfections using heavylift jack-up system
PublicationSafety analysis is performed of cylindrical vertical steel tanks during erection using heavylift jack up system. During an assembly or repair process a set of hydraulic supports is used. It allows to use the in-place lifting of heavy steel constructions on the required height. Wind can strongly influence stability of the lifted tank. Any geometric imperfections can reduce the critical or limit load. In the work failures of the...
-
Optimization of the System for Determining the Volume of Tissue Needed for Breast Reconstruction
PublicationThis article presents techniques for reconstructing surfaces and volume calculations using a point cloud generated from 3D imaging. The main objective of this article was to optimize the voxel size for the most accurate representation of the surface of the female breast. We experimented with different methods for determining volume using images from the Intel D435i camera. In addition, we designed application and measurement station...
-
THE PANTOGRAPH AND ITS GEOMETRIC TRANSFORMATIONS - A FORMER POPULAR TOOL FOR COPYING AND SCALING
PublicationDevelopment of digital technology has resulted in significant transformations of designer workshops. Computer applications replaced the previously existing tools and methods for drawing up of projects. Professional, sophisticated drawing instruments and tools for manual plotting, as well as basic drawing aids, have gradually fallen into oblivion and become relicts of a bygone era - the objects of collectors' interest. Gdansk University...
-
Load-settlement characteristics of piles working in a group
PublicationLoad-settlement characteristic (Q-s) of an axially loaded pile can be empirically determined from a static pile load test or on the basis of calculations using, e.g. transfer functions or numerical methods (FEM). The transfer functions method usually rely on empirical data, i.e. the function parameters are determined on the basis of numerous pile test results. Thus this method takes into account pile installation technology and...
-
Criteria for selection of working fluid in low-temperature ORC
PublicationThe economics of an ORC system is strictly linked to thermodynamic properties of the working fluid. A bad choice of working fluid could lead to a less efficient and expensive plant/generation unit. Some selection criteria have been put forward by various authors, incorporating thermodynamic properties, provided in literature but these do not have a general character. In the paper a simple analysis has been carried out which resulted...
-
"3D-Breast System for Determining the Volume of Tissue Needed for Breast Reconstruction"
PublicationThis article presents methods for surface reconstruction and volume determination based on the point cloud created by 3D imaging. Such a system would be used to accurately estimate breast volume in patients classified for breast reconstruction surgery at plastic surgery centers. To develop such a system, various methods of determining volume, based on images from the Intel D435i camera, were tested. In addition, an application...
-
Experiments on Preserving Pieces of Information in a Given Order in Holographic Reduced Representations and the Continuous Geometric Algebra Model
PublicationGeometric Analogues of Holographic Reduced Representations (GAc, which is the continuous version of the previously developed discrete GA model) employ role-filler binding based on geometric products.Atomic objects are real-valued vectors in n-dimensional Euclidean space and complex statements belong to a hierarchy of multivectors. The property of GAc and HRR studied here is the ability to store pieces of information in a given...
-
On the durability of the hydraulic satellite motor working mechanism in overload condition
PublicationThe paper presents the newest construction of the hydraulic satellite pump/motor. In this study, the fracture of the hydraulic satellite motor working mechanism is investigated. Factors influencing the durability of satellite working mechanism have been described. The durability of the hydraulic satellite motor working mechanism at a load, corresponding to a pressure of 15 MPa supplied with refined rapeseed oil is very low. Analyses...
-
Influence of electrode geometric arrangement on the operation of narrow circular electrostatic precipitator
PublicationIn this work the influence of electrode geometric arrangement on the operation of a circular electrostatic precipitator (ESP) was investigated using Particle Image Velocimetry (PIV) method. The ESP was a glass circular cylinder (29 mm in diameter, 300 mm long) equipped with a wire discharge electrode and circular-cylinder collecting electrode. The stainless-steel discharge wire electrode (0.23 mm in diameter, 100 mm long) was mounted...
-
3D-Breast System for Determining the Volume of Tissue Needed for Breast Reconstruction
Publication3D imaging systems can be used to effectively determine breast volumes for surgical applications. This article presents methods for surface reconstruction and volume determination based on the point cloud created by 3D imaging. Such a system would be used to accurately estimate breast volume in patients classified for breast reconstruction surgery at plastic surgery centers. To develop such a system, various methods of determining...
-
Journal of Geometric Mechanics
Journals -
Algebraic and Geometric Topology
Journals -
GEOMETRIC AND FUNCTIONAL ANALYSIS
Journals -
Bearing capacity of the working platform with kinematic method
PublicationBearing capacity of the working platform for heavy tracks was analysed using Distinct Layout Optimization (DLO) method. The platform layer constructed from cohesionless soils is resting on weak cohesive subgrade. Different thickness of the platform, its effective angle of internal friction and undrained shear strength of the soft soil were taken into consideration. Kinematic method permits different failure mechanisms to be analyzed....
-
Identification and simulation of shells geometric initial imperfection
PublicationPrzedstawiono stochastyczną analizę stalowych zbiorników walcowych ze wstępnymi imperfekcjami geometrycznymi. Imperfekcje opisano za pomocą jednorodnych pól losowych.
-
Tensor-product versus geometric-product coding
PublicationKodowanie przy pomocy iloczynów tensorowych, a kodowanie przy pomocy iloczynów geometrycznych. Formalizm jest zilustrowany przy pomocy paru przykładów.
-
Effect of geometric imperfections on aluminium silo capacities
PublicationAn aluminum silo with initial imperfections is analysed. Two types of imperfections are considered. The first one takes the form of local indentations in the shell; their size and range are adopted on the basis of the standard guidelines. The second type is a global imperfection described through the use of its eigenforms and by means of two-dimensional random fields. The calculations are limited to two cases of loading: negative...
-
A Comparability of Renal Length and Volume Measurements in MRI and Ultrasound in Children
PublicationIntroduction: Despite the significant increase in use of magnetic resonance imaging (MRI) in children, there is still a lack of normal reference values of renal size in this method and reference values are being interpolated from the ultrasound (US) studies. The study provides comparative analysis of agreement in renal length and volume measurements between MRI and ultrasound. Materials and Methods: Ninety-three children with a...
-
Working Conditions in Global Value Chains: Evidence for European Employees
PublicationThis article investigates a sample of almost nine million workers from 24 European countries in 2014 to conclude how involvement in global value chains (GVCs) affects working conditions. We use employer–employee data from the Structure of Earnings Survey merged with industry-level statistics on GVCs based on the World Input-Output Database. Given the multidimensional nature of the dependent variable, we compare estimates of the...
-
Working Conditions in the Context of Global Value Chains and Routinisation: An Example of Polish Workers
PublicationThe paper aims to explore the linkages between global production fragmentation, routinisation and the well-being of workers in Poland. In particular, the focus is placed on the selected measures of working conditions, such as the social environment, work intensity, and working time quality to examine their dependence on involvement in international trade and the routinisation level. We merge individual data describing the working...
-
Integrated model for the fast assessment of flood volume: Modelling – management, uncertainty and sensitivity analysis
PublicationThe specific flood volume is an important criterion for assessing the performance of sewage networks. It has been shown that its value is greatly influenced by the layout of the sewers in the catchment area, which is usually expressed by a fractal dimension. Currently, only mechanistic models (such as SWMM) enable the determination of the impact of the layout of the sewers on flooding volume, but they require additional and robust...
-
A comparison of geometric analogues of holographic reduced representations, original holographic reduced representations and binary spatter codes
PublicationGeometric Analogues of Holographic Reduced Representations (GA HRR) employ role-filler binding based on geometric products. Atomic objects are real-valued vectors in n-dimensional Euclidean space and complex statements belong to a hierarchy of multivectors. The paper reports a battery of tests aimed at comparison of GA HRR with Holographic Reduced Representation (HRR) and Binary Spatter Codes (BSC). Firstly, we perform a test of...