displaying 1000 best results Help
Search results for: PILE BASE RESISTANCE, PILE SHAFT RESISTANCE, CPTU-BASED METHODS
-
Iron doped manganese cobaltite spinel coatings produced by electrophoretic co-deposition on interconnects for solid oxide cells: Microstructural and electrical characterization
PublicationWe report a systematic microstructural and electrical characterization of iron doped Mn–Co spinel coatings processed by electrophoretic co-deposition of Mn1.5Co1.5O4 and Fe2O3 powders on Crofer 22 APU and AISI 441 steel substrates. Iron addition to Mn–Co spinel coating leads to a reduction of the area specific resistance on both substrates, after 3200 h at 750 °C. The Fe doped Mn–Co coating both leads to a thinner oxide scale and...
-
LOW NOISE TIRES FOR HYBRID AND ELECTRIC VEHICLES
PublicationLow Emission Vehicles that are hybrid and electric cars may benefit from specially designed tires that are optimized for driving conditions typical for such vehicles. It is possible that in the future Low Emission Vehicles, especially passenger cars, will substitute conventional vehicles in all applications, however for the time being they are mostly used in urban and suburban areas. Urban traffic has a rather low demand for grip...
-
A Wearable System Developed to Monitor People Suffering from Vasovagal Syncope
PublicationA wearable system for monitoring non-invasively signals invaluable when examining person suffering from vasovagal syncope is presented in the paper. Following signals are continuously recorded: electrocardiogram, photopletysmogram, impedance cardiogram and electrodermal resistance.
-
Reducing common mode voltage and bearing currents in quasi - resonant DC - link inverter
PublicationIn the paper, a concept of separation of an inverter-fed induction motor drive from its mains supply by two transistor switches inserted in the dc-link circuit is reexamined based on the proposed parallel quasi-resonant dc-link inverter (PQRDCLI). The objective of the paper is to show an advantage of the proposed topology in limiting high frequency common mode voltage and bearing currents. In the laboratory setup, an induction...
-
Recent progress in ultra-low formaldehyde emitting adhesive systems and formaldehyde scavengers in wood-based panels: a review
PublicationTraditional wood-based panels are produced with synthetic, formaldehyde-based adhesives, commonly made from fossil-derived constituents, such as urea, phenol, melamine, etc. Along with their numerous advantages, such as chemical versatility, high reactivity and excellent adhesive performance, these adhesives are characterized by certain problems, connected with the hazardous volatile organic compounds (VOCs), mostly free formaldehyde...
-
Bitumen Aging—Laboratory Simulation Methods Used in Practice and Selected Directions of Research on New Methods
PublicationChanges in the properties of bitumen binders that occur as a result of aging have a huge impact on the durability of products produced from them. In particular, asphalt pavements, which constitute the most common use of petroleum bitumen, are susceptible to damage resulting from the increasing stiffness of the bitumen during its life cycle. Increased stiffness of asphalt pavements reduces the pavement resistance to low-temperature...
-
The forecasted values of cutting power for sawing on band sawing machines for Polish Scots pine wood (Pinus sylvestris L.) in a function of its provenance.
PublicationIn this paper the predicted values of cutting power for band sawing machine (EB 1800, f. EWD), which is used in the Polish sawmills, were showed. The values of cutting power were forecasted for Scots pine (Pinus sylvestris L.) wood of five provenances from Poland. These values were determined using an innovative method of predicting the cutting power, which takes into account of elements of fracture mechanics. The resulting predictions...
-
Heterogeneous distribution of surface electrochemical activity in polycrystalline highly boron-doped diamond electrodes under deep anodic polarization
PublicationThe surface homogeneity of boron-doped diamond electrodes is variable and depends on anodic polarization conditions. The differentiation factor is the gradual and localized change in surface termination. A series of measurements under different polarization conditions was performed in order to investigate the scale of this effect. Nanoscale impedance microscopy (NIM) revealed large variation of surface resistance in individual...
-
Nickel Oxide Thin Film Sensor for Fluctuation-Enhanced Gas Sensing of Formaldehyde
PublicationNanocrystalline nickel-oxide-based thin films were prepared by advanced reactive gas deposition, and the response of these films to formaldehyde was studied by fluctuationenhanced sensing. Morphological and structural analyses showed porous deposits of nickel oxide particles with face-centered cubic structure. Resistance fluctuations were measured upon exposure to ethanol, formaldehyde and methane at 200 °C. Power density spectra...
-
Electrophoretic deposition and characterization of composite chitosan/Eudragit E 100 or poly(4-vinylpyridine)/mesoporous bioactive glass nanoparticles coatings on pre-treated titanium for implant applications
PublicationTitanium implants are surface-modified to achieve bioactivity and often antibacterial properties. Such surface coatings may increase corrosion degradation and be weakly attached to the substrate. In the present research, biodegradable composite coatings, investigated so far as smart environment-sensitive, slowly releasing silver to the implant neighborhood, were produced as a combination of chitosan (CS) with Eudragit E 100 (EE100)...
-
Low cost set-up for supercapacitors parameters evaluation
PublicationWe propose a use of a power amplifier in the circuit of voltage to current converter (current driver) for supercapacitor charging/discharging in controlled conditions. The current driver is controlled by DAC output of DAQ board and voltage of DUT is measured and a control loop is realized by software. In the circuit the DC current method of evaluation of capacitance and equivalent series...
-
Chemosensitization of multidrug resistant Candida albicans by the oxathiolone fused chalcone derivatives
PublicationThree structurally related oxathiolone fused chalcone derivatives appeared effective chemosensitizers, able to restore in part sensitivity to fluconazole of multidrug-resistant C.albicans strains. Compound 21 effectively chemosensitized cells resistant due to the overexpression of the MDR1 gene, compound 6 reduced resistance of cells overexpressing the ABC-type drug transporters CDR1/CDR2 and derivative 18 partially reversed fluconazole...
-
Three electrode configuration measurements of electrolyte-diffusion barrier-cathode interface
PublicationMeasurements of a system consisting of cathode/doped ceria diffusion barrier/doped zirconia electrolyte were made using two- and three-electrode configuration. Results obtained on a three-electrode measurement configuration were compared with and reflect the results obtained in two-electrode configuration. Three-electrode measurements allowed separating the impact of the symmetrical interface in the investigated system. They also...
-
Advanced operating methods
PublicationSelected operating methods of resistive gas sensors were presented. The methods utilize flicker noise (1/f noise), which gives additional information about ambient gas when compared with the recorded changes of DC resistance only. Methods of flicker noise measurements were outlined. Recently developed prototype gas sensors comprising golden nanoparticle functionalized with organic ligands can generate intense flicker noise induced...
-
Analysis of the Possibility of Using New Types of Protective Coatings and Abrasion-Resistant Linings under the Operating Conditions of the Spiral Classifier at KGHM Polska Miedź S.A. Ore Concentration Plant
PublicationA study was carried out to select the appropriate coatings for corrosion protection of the spiral classifier working at KGHM Polska Miedź S.A. Ore Concentration Plant. The abrasion resistance of selected protective coatings and wear-resistant linings was investigated using a DT-523 rotary abrasion tester with Taber CS-10 rubber abrasive discs. The average weight loss of the coatings after a cycle of 2000 revolutions was determined....
-
Sensory analysis of confectionery products.
Open Research DataThe data set presents the results of the sensory analysis of confectionery products, which was carried out by the sensory profiling analysis method based on the PN-ISO 11035: 1999 standard – “Sensory analysis - Identification and selection of descriptors for determining the sensory profile using multivariate methods”. The method was used to evaluate...
-
Column base fixity in steel moment frames: Observations from instrumented buildings
PublicationThe rotational fixity of column base connections in Steel Moment Resisting Frames (SMRFs) strongly influences their seismic response. However, approaches for estimating base fixity have been validated only against laboratory test data. These approaches are examined based on strong motion recordings from four instrumented SMRF buildings in California to informbest practices for seismic response simulation. These buildings represent...
-
The Influence of Gas Mixture in the Glow-Discharge Nitriding Process of Austenitic Stainless Steel on Characteristic of Nitrided Cases
PublicationAustenitic stainless steels characterize with excellent corrosion resistance, although low mechanical properties. In many cases that limits their exploitation in industrial applications. Moreover, austenitic stainless steel is susceptible to local corrosion in the presence of halide ions. In present works, it was emphasized that the nitriding of austenitic stainless steels gives some potential abilities to obtain beneficial effect...
-
Linear and branched polyester resins based on dimethyl-2,5-furandicarboxylate for coating applications
PublicationIn this study, novel bio-based hydroxyl-functional (co)polyesters from dimethyl-2, 5-furandicarboxylate (DMF), 2,3-butanediol, and a variety of comonomers viz. glycerol, pentaerythritol or trimethylolpropane are prepared using a solvent-free, bulk polycondensation technique. Extensive molecular and thermal characterization was performed to elucidate the properties of these materials. The materials showed suitable properties for solvent-borne...
-
Biocompatibility and bioactivity of load-bearing metallic implants
PublicationThe main objective of here presented research is to develop the titanium (Ti) alloy base composite materials possessing better biocompatibility, longer lifetime and bioactivity behaviour for load-bearing implants, e.g. hip joint and knee joint endoprosthesis. The development of such materials is performed through: modeling the material behaviour in biological environment in long time and developing of new procedures for such evaluation;...