Filters
total: 2151
filtered: 1727
displaying 1000 best results Help
Search results for: MULTIPHASE FLOWS
-
E-cohomological Conley index
PublicationIn this thesis we continue with developing the E-cohomological Conley index which was introduced by A.Abbondandolo. In particular, we generalize the index to non-gradient flows, we show that it an possesses additional multiplicative structure and we prove the continuation principle. Then, using continuation principle, we show how the computation of the E-cohomological Conley index can be reduced to the computation of the classical...
-
CO2 capture using steam ejector condenser under electro hydrodynamic actuator with non-condensable gas and cyclone separator: A numerical study
PublicationThe concept for condensation of steam and CO2 separation in a negative CO2 emission gas power plant involves the utilization of a steam ejector condenser (SEC) for direct-contact condensation of vapor with inert gas (CO2) on a spray of subcooled liquid, integrated with a separator to produce pure CO2. Due to the increasing diffusion resistance and reduced convective heat transfer between the steam and subcooled water phases...
-
Application of gas flow headspace liquid phase micro extraction coupled with gas chromatography-mass spectrometry for determination of 4-methylimidazole in food samples employing experimental design optimization
Publication -
The effect of a miniature argon flow rate on the spectral characteristics of a direct current atmospheric pressure glow micro-discharge between an argon microjet and a small sized flowing liquid cathode
Publication -
Coupling of cold vapor generation with an atmospheric pressure glow microdischarge sustained between a miniature flow helium jet and a flowing liquid cathode for the determination of mercury by optical emission spectrometry
Publication -
Pulse-Modulated Radio-Frequency Alternating-Current-Driven Atmospheric-Pressure Glow Discharge for Continuous-Flow Synthesis of Silver Nanoparticles and Evaluation of Their Cytotoxicity toward Human Melanoma Cells
Publication -
Cavitation resistance of OH18N9 steel alloyed with vaidus amount of TiC or Mn by means of laser beam. XIV International Symposium on Gas Flow, Chemical Lasers and High Power Lasers.
PublicationPrzedstawiono badania odporności kawitacyjnej stali OH18N9T po laserowym stopowaniu jej powierzchni węglikiem TiC oraz manganem. Wykazano, że wzbogacenie obrabianej stali manganem powoduje przemiany fazowe pod wpływem działania obciążeń kawitacyjnych, co przyczynia się do wzrostu odporności kawitacyjnej. Wzmacnianie stali węglikiem TiC powoduje natomiast zanik zdolności stali do wzmacniania odkształceniowego.
-
Adoption of the F-statistic of Fisher-Snedecor distribution to analyze importance of impact of modifications of injector opening pressure of a compression ignition engine on specific enthalpy value of exhaust gas flow
PublicationThis article analyzes the effect of modifications of injector opening pressure on the operating values of a compression ignition engine, including the temperature of the fumes. A program of experimental investigation is described, considering the available test stand and measurement capabilities. The structure of the test stand on which the experimental measurements were conducted is presented. The method of introducing real modifications...
-
Comparative study of high‑pressure fluid flow in densely packed granules using a 3D CFD model in a continuous medium and a simplified 2D DEM‑CFD approach. Granular Matter
PublicationIzotermiczny ściśliwy jednofazowy przepływ cieczy przez niejednorodną masę ziarnistą składającą się z gęsto upakowanych zachodzących na siebie kul imitujących skałę pod wysokim ciśnieniem zbadano numerycznie przy użyciu dwóch różnych podejść. Pierwsze podejście zwane pełnym modelem 3D CFD stosowało metodę skończonych objętości (FVM) do rozwiązania uśrednionego równania Naviera-Stokesa zakładając model naprężeń Reynoldsa (BSL) w...
-
Compressible gas density measurement by means of Fourier analysis of interferograms
PublicationThis paper describes a method for nonintrusive compressible gas density measurement by means of automated analysis of interferograms using FFT (Fast Fourier Transform), and its implementation using DFT (Discrete Fourier Transform), that does make this measurement technique a fairly valuable and accessible experimental method. The presented approach makes it possible to use the finite fringe setting of the interferometer, thus reducing...
-
DIGITAL HYDRAULICS CIRCUIT BASED ON PWM FUNCTION FOR CONTROLLING HYDRAULIC ACTUATOR POSITION
PublicationHydraulic systems are used in many different industries, such as multi-source hydrostatic drive systems. In traditional hydraulic systems, a proportional servo valve is used to control the position of hydraulic actuators. The low energy efficiency and high cost of these control valves are two major problems with these systems. Digital hydraulics is one of the most unique ideas on how to solve these problems. Researchers like digital...
-
On the use of the cumulative strain energy density for fatigue life assessment in advanced high-strength steels
PublicationIn this paper, the applicability of the cumulative strain energy density is explored as a fatigue indicator parameter for advanced high-strength steels subjected to strain-controlled conditions. Firstly, the cyclic stress-strain responses of nine steels, selected from three multiphase families, encompassing different elemental compositions and different heat treatment routes, were studied. Then, the predictive capabilities of the...
-
Nutrient transport and acquisition by diatom chains in a moving fluid
PublicationThe role of fluid motion in delivery of nutrients to phytoplankton cells is a fundamental question in biological and chemical oceanography. In the study of mass transfer to phytoplankton, diatoms are of particular interest. They are non-motile, are often the most abundant components in aggregates and often form chains, so they are the ones expected to benefit most from enhancement of nutrient flux due to dissipating turbulence....
-
DO WE NEED NAVIER NUMBER? – FURTHER REMARKS AND COMPARISON WITH ANOTHER DIMENSIONLESS NUMBERS
PublicationThis paper presents a role of the Navier number (Na-dimensionless slip-length) in universal modelling of flow reported in micro- and nano-channels like: capillary biological flows, fuel cell systems, micro-electro-mechanical systems and nano-electro-mechanical systems. Similar to another bulk-like and surface-like dimensionless numbers, the Na number should be treated as a ratio of internal viscous to external viscous momentum...
-
HYDROGEN PRODUCTION PERFORMANCE IN THERMOCATALYTIC REACTOR BASED ON THE INTERMETALLIC PHASE OF NI3AL
PublicationThe main aim of the following paper is mathematical modelling for momentum, heat and mass transfer, which is accompanied by chemical surface reactions of the flow of the mixture helium and methanol. The thermocatalytic devices used for decomposition of hydrocarbons incorporate vertical microchannels coupling at the ends and heated to 500 oC at the walls. The results of the experiment were compared with CFD calculations to calibrate...
-
Equations of tribological parameters for liquid flow in boundary layer on the tissue surface in bioreactor = Wyznaczanie parametrów tribologicznych dla przepływu cieczy w warstwie granicznej na powierzchni tkanki w bioreaktorze
PublicationW niniejszej pracy przedstawiony został problem tribologiczny wynikający z przepływu nieustalonego odżywczej cieczy lepkiej w cienkiej warstwie przyściennej w bezpośrednim kontakcie z zewnętrzną powierzchnią warstwy wierzchniej wzrastających komórek (chondrocytów) w trakcie procesu ich hodowli w bioreaktorze. Efektem rozważań będą wartości sił tarcia powstające na powierzchni wzrastającej tkanki. Najnowsze badania wykazały lepszą...
-
Discussion of “Development of an Accurate Time integration Technique for the Assessment of Q-Based versus h-Based Formulations of the Diffusion Wave Equation for Flow Routing” by K. Hasanvand, M.R. Hashemi and M.J. Abedini
PublicationThe discusser read the original with great interest. It seems, however, that some aspects of the original paper need additional comments. The authors of the original paper discuss the accuracy of a numerical solution of the diffusion wave equation formulated with respect to different state variables. The analysis focuses on nonlinear equations in the form of a single transport equation with the discharge Q (volumetric flow rate)...
-
Simulations of high-pressure fluid flow in a pre-cracked rock specimen composed of densely packed bonded spheres using a 3D CFD model and simplified 2D coupled CFD-DEM approach
PublicationW artykule zastosowano dwa różne podejścia do opisu jednofazowego przepływu płynu w wstępnie spękanej próbce skały o niskiej porowatości pod wysokim ciśnieniem. Głównym celem pracy było bezpośrednie porównanie rozkładu ciśnień, gęstości i prędkości płynów we wstępnie pękniętej próbce. Zachowanie próbki imitującej skałę zostało opisane przez gęsto upakowane połączone kohezją kulki z nakładającymi się na siebie elementami. Pierwsze...
-
Influence of processing conditions on crystal structure of BiNbO 4 ceramics
PublicationBismuth niobate (BiNbO4) has attracted attention as a low-fired ceramics with promising microwave application potential. It belongs to the bismutocolumbite oxides with similarly to scheelite-like stibiotantalite structure (SbTaO4) A3+B5+O4. Aim of the present research was to fabricate BiNbO4 ceramics by solid state reaction route from the mixture of simple oxides viz. Bi2O3, and Nb2O5, and study its phase composition as well as...
-
Improvement of the thrust bearing calculation considering the convectional heating within the space between the pads
PublicationA modern thrust bearing calculation tool should consider not only the oil film between pad and rotating collar but also the space between the pads. The oil flow in the space has a significant influence on the oil film inlet temperature, the convectional cooling of pad and collar and should be included in the bearing calculation methods. The authors use a tool developed at Clausthal University of Technology in cooperation with the...
-
Prototype of an opto-capacitive probe for non-invasive sensing cerebrospinal fluid circulation
PublicationIn brain studies, the function of the cerebrospinal fluid (CSF) awakes growing interest, particularly related to studies of the glymphatic system in the brain, which is connected with the complex system of lymphatic vessels responsible for cleaning the tissues. The CSF is a clear, colourless liquid including water (H2O) approximately with a concentration of 99 %. In addition, it contains electrolytes, amino acids, glucose, and...
-
Social learning and knowledge flows in cluster initiatives, In: Sanz S.C., Blanco F.P., Urzelai B. (Eds). Human and Relational Resources (pp. 44-45). the 4th International Conference on Clusters and Industrial Districts CLUSTERING, University of Valencia, Spain, May 23–24 (ISBN: 978-84-09-11926-4).
PublicationPurpose – The purpose of the paper is to explore how learning manifests and knowledge flows in cluster initiatives (CIs) due to interactions undertaken by their members. The paper addresses the research question of how social learning occurs and knowledge flows in CIs. Design/methodology/approach – The qualitative study of four cluster initiatives helped to identify various symptoms of social learning and knowledge flows in...
-
On some extensions of Murray's Law
PublicationThis paper cites the original Murray's law about optimal radii.Extensions to some class of non-newtonian flows that aredescribedby Ostwalda-de Waele model and newtonian flows foreliptical crosssections. A generalisation of Murray's law formultiobjectiveformulation is also given. It is shown that theoriginal formulation of optimal condition is a particular case ofmultiobjective formulation.
-
Impact of diffusion coefficient averaging on solution accuracy of the 2D nonlinear diffusive wave equation for floodplain inundation
PublicationIn the study, the averaging technique of diffusion coefficients in the two-dimensional nonlinear diffusive wave equation applied to the floodplain inundation is presented. As a method of solution, the splitting technique and the modified finite element method with linear shape functions are used. On the stage of spatial integration, it is often assumed that diffusion coefficient is constant over element and equal to its average...
-
Application of Analytic Signal and Smooth Interpolation in Pulse Width Modulation for Conventional Matrix Converters
PublicationThe paper proposes an alternative and novel approach to the PWM duty cycles computation for Conventional Matrix Converters (CMC) fed by balanced, unbalanced or non–sinusoidal AC voltage sources. The presented solution simplifies the prototyping of direct modulation algorithms. PWM duty cycles are calculated faster by the smooth interpolation technique, using only vector coordinates, without trigonometric functions and angles. Both...
-
Analiza przepływu oleju przez rowek smarowy wzdłużnego łożyska ślizgowego z wykorzystaniem komputerowej dynamiki płynów (CFD) = Analysis of the lubricant flow through the hydrodynamic thrust bearings groove with the use of computational fluid dynamic
PublicationSmarowanie zanurzeniowe jest tradycyjnym sposobem smarowania wzdłużnych łożysk ślizgowych. Jednak rozwiązanie to wykazuje umiarkowaną skuteczność w zapewnieniu optymalnie niskich temperatur w filmie smarowym a ponadto jest przyczyną strat mocy związanych z mieszaniem oleju w obudowie łożyska, co jest szczególnie widoczne w łożyskach szybkoobrotowych. Obecnie wymagania stawiane nowym konstrukcjom łożysk ślizgowych to zwiększanie...
-
Multi-pulse VSC arrangements with coupled reactors
PublicationThis paper presents a novel approach to the multipulse VSC (Voltage Source Converter) arrangements based on several conventional inverter modules connected in parallel by using coupled reactors. This solution reduces the THD of the output voltage, despite the low switching frequency of transistors. The advantage of the proposed solution is also a relatively small rated power of the reactors. Proposed new arrangements for different...
-
An approach to improve the time efficiency of disjoint paths calculation
PublicationFailures of network elements can be appropriately dealt with by utilization of alternate disjoint paths to provide redirection of flows affected by failures of the respective working paths. Known approaches can be broadly divided by decision on backup paths installation into proactive and reactive mechanisms, as well as based on the scope of recovery actions into local and global rerouting. There are several important scenarios...
-
Economic Integration and Foreign Direct Investment: Review of Main Theoretical Concepts
PublicationThe objective of the article is to present key theoretical relationships between economic integration and FDI flows. The research method used is a comprehensive literature review. Most influential publications, including books, articles, working papers, etc. contributing to the subject were identified. The review consists of two essential parts: theory of FDI, and theoretical relationships between economic integration and FDI flows....
-
A Simplified SVPWM Technique for Five-leg Inverter with Dual Three-phase Output
PublicationThis article proposes a simplified space vector pulse-width modulation (SVPWM) technique five-leg inverter with dual three-phase output. An idea to fed the dual tree-phase machine by the multiphase voltage source inverters (VSIs) is not new. Dual- and multi-motor drive systems are widely used in the industry applications. The most popular fields are: electric vehicles (EVs) and traction systems. Moreover, the specific characteristic...
-
[Chapter] 22. Application of physical modeling to study combustion process-es and flow patterns in large-scale boilers and furmaces. W: Optical me- thods and data processing in heat and fluid flow. Ed. C. Greated, J. Cos-grove, J.M. Buick. Bury St. Edmunds. London: Profess. Eng. Publ.**2002 s. 267-277, 4 rys. bibliogr. 6 poz. Zastosowanie modelowania fizycznego do badania procesów spalania pola prze- pływu w przemysłowych kotłach i piecach.
PublicationRozdział zawiera wyniki badań modelowania fizycznego dwuwymiarowego i trój-wymiarowego pola przepływu i procesów spalania w wybranych urządzeniachprzemysłowych.
-
Pial artery and subarachnoid width response to apnoea in normal humans
PublicationBackground: Little is known about intracranial pressure (ICP)-cerebral haemodynamic interplay during repetitive apnoea. A recently developed method based on near-infrared transillumination/backscattering sounding (NIR-T/BSS) noninvasively measures changes in pial artery pulsation (cc-TQ) as well as subarachnoid width (sas-TQ) in humans. Method: We tested the complex response of the pial artery and subarachnoid width to apnoea...
-
Analizy ilości i jakości odpływu wód deszczowych i roztopowych z kontrolowanej zlewni zurbanizowanej
PublicationIstotnym problemem Gdańska staje się bezpieczeństwo ekologiczne związane ze spływami miejskimi odprowadzanymi bezpośrednio do wód powierzchniowych, często akwenów użyteczności publicznej. W latach 2011÷2013, Katedra Hydrotechniki Wydziału Inżynierii Lądowej i Środowiska Politechniki Gdańskiej, we współpracy z Wojewódzkim Funduszem Ochrony Środowiska i Gospodarki Wodnej w Gdańsku oraz Gdańskimi Melioracjami, podjęła się wdrożenia...
-
MEASUREMENT AND ANALYSIS OF A FLOOD WAVE PROPAGATION ON THE KACZA RIVER IN GDYNIA IN NORTHERN POLAND
PublicationKacza river is located in northern Poland in the neighborhood of the Gulf of Gdansk and the Baltic Sea. A Kacza having length of 15 km and catchment area of 53 km2 collects the water into the Gulf mostly from inhabited and forested areas within the administrative boundaries of the city of Gdynia. On the 14th and 15th of July 2016 in northern Poland on the large area of Tri-City agglomeration (Gdynia, Gdansk and Sopot) total daily...
-
Explanation of Reduction of Pressure Forces in Turbine Chamber Seals
PublicationThe paper describes a chamber seal reducing the aerodynamic forces created in shroud seals. Asymmetrical pressure distribution (due to rotor-stator eccentricity) in the blade tip clearance leads to the creation of pressure forces acting on the blade shroud. By increasing the volume above the shroud, the pressure distribution becomes more uniform on the whole shroud circumference and the effect of rotor eccentricity is reduced....
-
ANALYSIS OF POSSIBILITIES FOR THE USE OF VOLUME-DELAY FUNCTIONS IN THE PLANNING MODULE OF THE TRISTAR SYSTEM
PublicationTravel time is a measure commonly used for traffic flow modelling and traffic control. It also helps to evaluate the quality of traffic control systems in urban areas. Traffic control systems that use traffic models to predict changes and disruptions in vehicle flows have to use vehicle speed-prediction models. Travel time estimation studies the effects of traffic volumes on a street section at an average speed. The TRISTAR Integrated...
-
Explanation of Reduction of Pressure Forces in Turbine Chamber Seals
PublicationThe paper describes a chamber seal reducing the aerodynamic forces created in shroud seals. Asymmetrical pressure distribution (due to rotor-stator eccentricity) in the blade tip clearance leads to the creation of pressure forces acting on the blade shroud. By increasing the volume above the shroud, the pressure distribution becomes more uniform on the whole shroud circumference and the effect of rotor eccentricity is reduced....
-
A Reputation Scheme to Discourage Selfish QoS Manipulation in Two-Hop Wireless Relay Networks
PublicationIn wireless networks, stations can improve their received quality of service (QoS) by handling packets of source flows with higher priority. Additionally, in cooperative relay networks, the relays can handle transit flows with lower priority. We use game theory to model a two-hop relay network where each of the two involved stations can commit such selfish QoS manipulation. We design and evaluate a reputation-based incentive scheme...
-
Liquid residence time in vortex separators
PublicationCentrifugal force enhances gravitational separation of suspension (vortex separators), as well as allows regulation of liquid discharge (vortex flow controls). Furthermore, it elongates the effective residence time of liquid inside the chamber in comparison to non-circulative flow. Laboratorz measurements, described in the paper, indicate that average liquid residence time for circulative flow exceeds 50% of plug-flow time,...
-
A Solution to Image Processing with Parallel MPI I/O and Distributed NVRAM Cache
PublicationThe paper presents a new approach to parallel image processing using byte addressable, non-volatile memory (NVRAM). We show that our custom built MPI I/O implementation of selected functions that use a distributed cache that incorporates NVRAMs located in cluster nodes can be used for efficient processing of large images. We demonstrate performance benefits of such a solution compared to a traditional implementation without NVRAM...
-
Study of a Flame Kernel Evolution in a Turbulent Mixing Layer Using LES with a Laminar Chemistry Model
Publication -
Investigation of the Aerodynamics of an Innovative Vertical-Axis Wind Turbine
PublicationThe paper presents the results of an experimental investigation and a three dimensional numerical analysis of the transient aerodynamic phenomena occurring in the innovative modification of classic Savonius wind turbine. An attempt to explain the increased efficiency of the innovative design a comparison with the traditional solution is undertaken. A vorticity measure based on the integral of the velocity gradient tensor second...
-
Modelling of two-component turbulent mass and heat transfer in air-fed pressurised suits
PublicationIn this paper the modelling of an important industrial problem is addressed, which involves the two-component turbulent flow with heat transfer that takes place inside protective clothing. The geometry of the flow boundaries is reconstructed in a CAD system from photogrammetry scan data. The overall model is sufficiently realistic to allow, after validation, design improvements to be tested. Those presented here allow the reduction...
-
Estimating the uncertainty of discharge coefficient predicted for oblique side weir using Monte Carlo method
PublicationSide weir is a hydraulic structure, which is used in irrigation systems to divert some water from main to side channel. It is installed at the entrance of the side channel to control and measure passing water into the side channel. Many studies provided side weir water surface profile and coefficient of discharge to measure water discharge diverted into the side channel. These studies dealt with different side weir shapes (rectangular,...
-
Recognition, understanding and aestheticization of freehand drawing flowcharts
PublicationIn this paper a concept of FCA, a system for recognizing, understanding and aestheticization of freehand drawing flow charts is described. The system is based on a proposed by the author FlowGram graph grammar describing flow charts drawing. An open format FlowChartML for flow charts description is also proposed. The aestheticization criterion is formulated that allows for automatic beautification of flow charts. First experiments...
-
Propagation of acoustic pulses in some fluids with yield stress
PublicationThis study is devoted to the derivation of approximate equations governing acoustic pulses in flows with yieldstress, including some time-dependent flows with a slow dependence on time of yield stress and apparent viscosity. Themodeling of yield stress and apparent viscosity in the vicinity of a zero deformation rate allows us to consider a thixotropicfluid as a Bingham plastic with coefficients that are dependent on time. The...
-
Shallow Water Equations as a Mathematical Model of Whitewater Course Hydrodynamics
PublicationPredicting the positions of local hydraulic phenomena, as well as accurately esti-mating the depth and velocity of the water flow are necessary to correctly config-ure a whitewater canoeing course. Currently, a laboratory and full 3D CFD model-ing are typically used in the design process to meet these needs. The article points to another possibility which can be useful at the preliminary stage of the design. The authors show that...
-
The Application of Fluidic Sealing in Shrouded Gas Turbine Blades
PublicationThis paper presents a study conducted on a new gas turbine designed to limit leakage in the labyrinth seal. The slots in the fin are used to generate a bypass flow, which obstructs the flow in the gap above the fin. The method was tested numerically and experimentally beforehand using a simplified model without rotation or blade passages. In this paper, the validation of the method using a model of a turbine stage is shown. Reynolds-averaged...
-
Modelling of heat transfer in supercritical pressure recuperators
PublicationIn the paper presented is analysis of convective flow heat transfer at supercritical pressure in channels of heat exchanger working in the thermodynamic cycle. The modelling is based on the division of the flow into three regions, namely the heavy fluid, a two phase flow consisting of the heavy and light fluids and finally the light fluid flow. Modelling is concentrated on the region of simultaneous flow of two fluids divided into...
-
Marine traffic risk modelling – an innovative approach and a case study
PublicationThis paper presents a model to analyse the risk of two common marine accidents: collision and grounding. Attention is focused on oil tankers since they pose the highest environmental risks. A case study in selected areas of the Gulf of Finland in ice-free conditions is presented. The model utilizes a formula for risk calculation that considers both the probability of an unwanted event and its consequences. The model can be decomposed...