Filters
total: 1136
filtered: 946
Search results for: UNDERWATER COATINGS
-
Electrochemical approach to evaluate the interlayer adhesion of organic coatings
PublicationZastosowano elektrochemiczną spektroskopię impedancyjną do wyznaczania międzywarstwowej adhezji w powłokach organicznych. Zbadano różne zestawy powłok do ochrony samochodów. Zastosowano dwie elektrody wykonane z prądoprzewodzącego tuszu umieszczone pomiędzy warstwami powłokowymi. Stwierdzono, że utrata adhezji międzywarstwowej następuje podobnie jak zmiany energii aktywacji przewodnictwa jonowego w obszarze międzywarstwowym. Uzyskane...
-
Effect of WC on electroposition and corossion behaviour of chromium coatings
PublicationWłaściwości warstw chromowych zawierających różne ilości drobin WC zbadano metodą XPS, EPS oraz XRD. Metody te pozwoliły określić morfologię i skład chemiczny powłok. Właściwości antykorozyjne określono dla różnych czasów ekspozycji próbek w elektrolicie zawierającym 0,01 mol L-1 za pomocą metody woltamperometrycznej oraz spektroskopii impedancyjnej. Badania wykazały, że obecność WC w warstwach chromowych otrzymanych z kąpieli...
-
Measurement microsystem for high impedance spectroscopy of anticorrosion coatings
PublicationW artykule przedstawiono mikrosystem do pomiarów bardzo dużych impedancji ukierunkowany na identyfikację parametrów powłok antykorozyjnych metodą spektroskopii impedancyjnej. Do wyznaczania składowych ortogonalnych sygnałów pomiarowych zastosowano w nim technikę cyfrowego przetwarzania sygnałów. Pozwoliła ona na uzyskanie szerokiego zakresu częstotliwości pomiarowych, zwłaszcza bardzo niskich, od ćHz, przy zachowaniu prostej konstrukcji...
-
Microstructure and residual stresses in surface coatings with PTFE reservoirs
PublicationThe paper presents the results of experimental study into the microstructure and changes in residual stresses resulting from sliding and rolling/sliding loaded interaction between metallic surface coatings with embedded PTFE reservoirs and various counter faces. It was found that before testing surface coatings had compressive residual stresses. Molybdenum coating with all types of PTFE reservoirs displayed, as a result of testing,...
-
WEAR OF Si OR B DOPED AMORPHOUS CARBON COATINGS
PublicationThe paper describes a complex wear research on DLC (amorphous carbon) moped with boron (B) and silicone (Si). The tests were carried out in two different sliping systems: flat–on–flat (ring contact, unidirectional sliding) and ball–on–flat (reciprocating sliding). Water and medical saline solutions were used as lubricants. A comparative analysis of the results revealed differences in the initiation and progress of wear and the...
-
Evaluation of organic coatings condition with AFM-based method
PublicationThe paper presents an atomic force microscopy (AFM)-based approach to evaluation of local protective properties of organic coatings. Apart from topography, it provides local ac and dc characteristics of examined coating. The method consists in application of ac voltage perturbation signal between conductive AFM tip and coated metal substrate. The resulting current is used to determine local impedance characteristics. Both impedance...
-
Gold nanoparticles and their coatings, their effect on cells and their interaction with radiation
PublicationTwo nanometre gold nanoparticles (AuNPs), bearing sugar moieties and/or polyethylene glycolamine (PEG-amine), were synthesised and evaluated for their in vitro toxicity and ability to radiosensitise cells with 220 kV and 6 MV X-rays, using four cell lines representing normal and cancerous skin and breast tissues. In addition to the observed intrinsic cancer-selective chemotoxicity, these AuNPs acted as radiosensitisers in combination with...
-
Deposition of phosphate coatings on titanium within scaffold structure
PublicationPurpose: Existing knowledge about the appearance, thickness, and chemical composition of phosphate coatings on titanium inside porous structures is insufficient. Such knowledge is important for the design and fabrication of porous implants. Methods: Metallic scaffolds were fabricated by selective laser melting of 316L stainless steel powder. Phosphate coatings were deposited on Ti sensors placed either outside the scaffolds or...
-
Adhesion of organic coatings to hot-dip galvanized steel
PublicationDuplex systems provide long-time corrosion protection, much longer than the sum of the lifetimes of zinc and paint used individually. However loss of adhesion between coating and zinc substrate is often found in practice. Different methods of zinc surface preparations are used in the fi eld. The aim of this study was to examine and compare coating protection when the old zinc surface, stored during long-time period (15 years) in...
-
On the use of bilinear transformation for parameter identification of anticorrosion coatings
PublicationW artykule przedstawiono metodę identyfikacji parametrów powłok antykorozyjnych modelowanych wieloelementowymi układami zastępczymi. Metoda wykorzystuje właściwości przekształcenia biliniowego, które umożliwia przedstawienie funkcji układowej wieloparametrowego modelu jako funkcji każdego indywidualnego parametru. Odwrotne przekształcenie biliniowe pozwala na wyznaczenie wartości każdego z parametrów modelu z osobna na podstawie...
-
Effects of Surface Pretreatment of Titanium Substrates on Properties of Electrophoretically Deposited Biopolymer Chitosan/Eudragit E 100 Coatings
PublicationThe preparation of the metal surface before coating application is fundamental in determining the properties of the coatings, particularly the roughness, adhesion, and corrosion resistance. In this work, chitosan/Eudragit E 100 (chit/EE100) were fabricated by electrophoretic deposition (EPD) and both their microstructure and properties were investigated. The present research is aimed at characterizing the effects of the surface...
-
Innovative Energy-Saving Propulsion System for Low-Speed Biomimetic Underwater Vehicles
Publication -
Comparison of Different Course Controllers of Biomimetic Underwater Vehicle with Two Tail Fins
Publication -
Innovative Energy-Saving Propulsion System for Low-Speed Biomimetic Underwater Vehicles
Publication -
3D Form analysis of rope deformation with long towed underwater hydroacoustic antenna
PublicationArtykuł opisuje rozwiązanie zagadnienia brzegowego dla zestawu długiej liny holującej i podwodnej anteny hydroakustycznej o gęstości, tej ostatniej, nieznacznie większej od gęstości wody i małej sztywności. Znane jest tylko położenie punktu zamocowania liny do okrętu (p-kt początkowy holowanego zestawu) oraz głębokość, na której znajduje się koniec anteny. Przedstawiono analizę sił działających na holowany zestaw, ich równania...
-
Parametric method for determination of motion characteristics of underwater vehicles, applicable in preliminary designing.
Publicationartykuł zawiera opis metody wstępnego projektowania autonomicznych pojazdów podwodnych (auv), przydatnej szczególnie w przypadku, gdy w założeniach projektowych stawiane są wymogi dotyczące parametrów kinematyczno-dynamicznych ruchu pojazdu. koncepcja metody zasadza się na równaniach dynamiki opisujących ruch płaski pojazdu w kierunku poziomym i pionowym, wywołanych odpowiednio napędem śrubowym lub balastem wodnym. równania ruchu...
-
A New Fuzzy Sliding Mode Controller with PID Sliding Surface for Underwater Manipulators
PublicationDesign of an accurate and robust controller is challenging topic in underwater manipulator control. This is due to hydrodynamic disturbances in underwater environment. In this paper a sliding mode control (SMC) included a PID sliding surface and fuzzy tunable gain is designed. In this proposed controller robustness property of SMC and fast response of PID are incorporated with fuzzy rules to reduce error tracking. In the control...
-
Adaptive Identification of Underwater Acoustic Channel with a Mix of Static and Time-Varying Parameters
PublicationWe consider the problem of identification of communication channels with a mix of static and time-varying parameters. Such scenarios are typical, among others, in underwater acoustics. In this paper, we further develop adaptive algorithms built on the local basis function (LBF) principle resulting in excellent performance when identifying time-varying systems. The main drawback of an LBF algorithm is its high complexity. The subsequently...
-
Underwater acoustic communication system using broadband signal with hyperbolically modulated frequency
PublicationThe implementation of reliable acoustic underwater communication in shallow waters is a scientific and engineering challenge, mainly due to the permanent occurrence of the multipath phenomenon. The article presents the concept of a transmission system using a broadband signal with hyperbolically modulated frequency (HFM) to transmit data symbols and synchronize data frames. The simulation tests were carried out in channels with...
-
A Method for Underwater Wireless Data Transmission in a Hydroacoustic Channel under NLOS Conditions
PublicationWireless data transmission in the hydroacoustic channel under non-line-of-sight (NLOS) propagation conditions, for example, during a wreck penetration, is difficult to implement reliably. This is mostly due to the multipath propagation, which causes a reduction in the quality of data reception. Therefore, in this work an attempt has been made to develop a reliable method of wireless underwater communication test it under the NLOS...
-
Autonomous Control of the Underwater Remotely Operated Vehicle in Collision Situation with Stationary Obstacle
PublicationThe article considers the problem of autonomous control of the underwater remotely operated vehicle mini Remotely Operated Vehicle (ROV) in a collision situation with a stationary obstacle. The control of the collision avoidance process is presented as a synthesis of fuzzy proportional-differential controllers for the control of distance and orientation concerning the detected stationary obstacle. The control of the submergence...
-
Cold Cracking Of Underwater Wet Welded S355G10+N High Strength Steel
PublicationWater as the welding environment determines some essential problems influencing steel weldability. Underwater welding of high strength steel joints causes increase susceptibility to cold cracking, which is an effect of much faster heat transfer from the weld area and presence of diffusible hydrogen causing increased metal fragility. The paper evaluates the susceptibility to cold cracking of the high strength S355G10+N steel used,...
-
Effect of underwater wet welding conditions on the diffusible hydrogen content in deposited metal
PublicationIn the study mercury displacement method was used for determination of diffusible hydrogen amount in deposited metal obtained during underwater wet welding with covered electrodes in laboratory conditions according to a two-level full factorial design for three factors. The factors and their levels were chosen among conditions and parameters of welding in accordance with the results of own preliminary studies. A statistical analysis...
-
Thermo-Mechanical Simulation of Underwater Friction Stir Welding of Low Carbon Steel
PublicationThis article investigates the flow of materials and weld formation during underwater friction stir welding (UFSW) of low carbon steel. A thermo-mechanical model is used to understand the relation between frictional heat phenomena during the welding and weld properties. To better understand the effects of the water environment, the simulation and experimental results were compared with the sample prepared by the traditional friction...
-
System identification theory-based estimation of underwater acoustic channel for broadband communications.
PublicationPłytki kanał podwodny jest niestacjonarny z powodu wielokrotnych odbić fal dźwiękowych od powierzchni wody oraz ruchu nadajnika i odbiornika systemu komunikacyjnego. Dla zapewnienia szybkiej transmisji danych niezbędna jest estymacja kanału oparta na equalizacji adaptacyjnej. W systemach komunikacji podwodnej stosowane są zazwyczaj equalizery DFE z zaimplementowanymi algorytmami najmniejszych kwadratów: LMS oraz RLS.W artykule...
-
Determination of t8/5 cooling times for underwater local dry welding of steel
PublicationKnowledge of thermal history is the basic condition for studying the structure - properties of welded joints. The determinant of thermal history is the thermal cycle, whose in-situ measurements are still a big challenge. Water as the welding environment complicates this issue even more. The article presents a method to determine an equation for calculating t8/5 cooling times for underwater gas metal arc welding of unalloyed steels...
-
Using Fast Frequency Hopping Technique to Improve Reliability of Underwater Communication System
PublicationAcoustic underwater communication systems designed to work reliably in shallow coastal waters must overcome major limitations such as multipath propagation and the Doppler effect. These restrictions are the reason for the complexity of receivers being built, whose task is to decode a symbol on the basis of the received signal. Additional complications are caused by the low propagation speed of the acoustic wave in the water and...
-
Underwater in situ local heat treatment by additional stitches for improving the weldability of steel
PublicationIn this paper the influence of in situ local heat treatment performed by additional stitches on the weldability of high-strength low-alloy (HSLA) S355J2C+N steel was tested. The investigated steel is characterized by high susceptibility to cold cracking. It is necessary to find a method to improve the quality of welded joints. The local heat treatment was applied as an eect of bead-on plate welding made on the face of a Tekken...
-
Bead-on-plate welding on S235JR steel by underwater local dry chamber process
PublicationThe article presents the results of the effect of parameters of underwater local dry chamber welding on the properties of padding welds. The effect of heat input and the type of shielding gas on the structure and hardness of welds was established. the functions for estimating the maximum hardness of the heat affected zone have been also elaborated.
-
ADAPTIVE IDENTIFICATION OF TIME-VARYING IMPULSE RESPONSE OF UNDERWATER ACOUSTIC COMMUNICATION CHANNEL
PublicationThe transmission properties of underwater acoustic communication channel can change dynamically due to the movement of acoustic system transmitter and receiver or underwater objects reflecting transmitted signal. The time-varying impulse response measurement and estimation are necessary to match the physical layer of data transmission to instantaneous channel propagation conditions. Using the correlative measurement method, impulse...
-
THE EFFECT OF WET UNDERWATER WELDING ON COLD CRACKING SUSCEPTIBILITY OF DUPLEX STAINLESS STEEL
PublicationABSTRACT The present work was conducted to assess the weldability of duplex stainless steel in underwater conditions. Metal manual arc welding (MMA) with the use of coated electrodes was used in the investigations. Tekken weldability tests were performed underwater at 0.5 m depth and in the air. Nondestructive tests, metallographic examinations of welds, ferrite content assessment in microstructure and hardness test were performed....
-
Antimicrobial properties of protective coatings produced by plasma spraying technique
Publication -
Prediction of the properties of PVD/CVD coatings with the use of FEM analysis
Publication -
Porous, High Capacity Coatings for Solid Phase Microextraction by Sputtering
Publication -
Frequencies selection for accelerated cnls parameter identification of anticorrosion coatings
PublicationArtykuł przedstawia zmodyfikowaną metodę CNLS dopasowywania widma impedancyjnego dla identyfikacji parametrów obiektów technicznych. Liczba częstotliwości pomiarowych została ograniczona do liczby identyfikowanych parametrów, a ich wartości są dobierane w oparciu o różne kryteria. Jako obiekt testowy wybrano model powłoki antykorozyjnej. Wyniki symulowanej identyfikacji przeanalizowano pod kątem dokładności i zmniejszenia czasu...
-
Effect of environmental temperature variations on protective properties of organic coatings
Publication -
Surface quality of the plasma cermet coatings after grind finishing
Publication -
Integrated Quality Ensuring Technique of Plasma Wear Resistant Coatings
Publication -
Grinding specifics of plasma coatings melted with high-frequency currents
Publication -
Research into properties of wear resistant ceramic metal plasma coatings
Publication -
The Influence of Casein Coatings on the Corrosion Behavior of Mg-Based Alloys
Publication -
Preparation and Surface Characterization of Chitosan-Based Coatings for PET Materials
Publication -
Fatigue Bending of V-Notched Cold-Sprayed FeCoCrNiMn Coatings
PublicationCold-spray coatings were produced by FeCoCrNiMn high-entropy alloy powders deposited on carbon steel substrate. The coatings were realized at intermediate temperature and high pressure (at 1100 °C and 7 MPa). The coating microstructure was characterized by scanning electron microscopy and X-ray diffraction, revealing a very dense deposition and high flattening ratio of the splatted particles. This had a large influence on the...
-
Impact of low-temperature sintering on the Fe-based amorphous coatings
PublicationBulk metallic glasses (BMGs) have gained a lot of attention in recent years due to their outstanding properties such as high hardness and excellent wear and corrosion resistance. However, they are restricted in industrial applications due to their extreme brittleness. Iron based amorphous coatings from BMGs are the best solution to use them by overcoming the problem of extreme brittleness. The coatings can be sprayed by various...
-
Electrochemical Activity and Electrical Properties of Optimized Polypyrrole Coatings on Iron
PublicationIn this work, electrochemical activity and electrical properties of polypyrrole (PPy) coated iron electrodes have been investigated. PPy film was electrochemically polymerized from sodium salicylate aqueous solution under conditions, which provided an increase of iron corrosion resistance. It was noticed that the pH of the solution and the applied electrode potential range during the study of the polymer properties had an influence...
-
The protective properties of graphene oxide coatings functionalized with phosphorus atoms.
PublicationRecently, electrophoretically deposited graphene oxide coatings are commonly applied as an anti-corrosion layer. However, improper adjustment of electrophoretic deposition (EPD) parameters as well as the hydrophilic nature of graphene oxide contribute to the formation of defects in the coatings and the increase in the wetting properties, respectively, and thus lead to a reduction of protective properties. The growth of wetting...
-
Manganese Phosphatizing Coatings: The Effects of Preparation Conditions on Surface Properties
PublicationManganese phosphate coating could be used to protect the surface of steel products. However, it is essential to determine the effects which process parameters, as well as the types of additives used, have on the efficiency of coating deposition. Thus, we present here a process of phosphatization of low-alloy steel (for 15 min at 95 ◦C) in manganese/nickel baths followed by a passivation process with the use of a silicon and zircon...
-
Degradation of organic coatings subjected to alternating mechanical stress impact.
PublicationW pracy przedstawiono wyniki badań nad wpływem cyklicznych naprężeń mechanicznych na dwa rodzaje systemów powłokowych stosowanych do ochrony konstrukcji mostowych. Powłoki epoksydowe i winylowe poddano cyklom zginanie/odpuszczenie w granicach odkształceń elastycznych materiału podłoża. Stan powłok oceniano przy użyciu techniki elektrochemicznej spektroskopii impedancyjnej. Otrzymane wyniki porównano z zachowaniem analogicznych...
-
Application of the dynamic EIS to investigation of transport within organic coatings
PublicationW pracy przedstawiono wyniki badań nad gwałtownym niszczeniem organicznych powłok ochronnych. Zastosowano technikę Dynamicznej Elektrochemicznej Spektroskopii Impedancyjnej (DEIS). Przez 60 sekund powłoka poliwinylowa poddawana była działaniu chlorku metylenu. W tym czasie rejestrowano chwilowe widma impedancyjne, co pozwoliło na prześledzenie dynamiki procesu degradacji powłoki. Potwierdzono przydatność techniki DEIS w badaniu...
-
Fatigue damage evaluation of organic coatings subjected to mechanical stress
PublicationZnaczna liczba konstrukcji ulega niszczeniu zmęczeniowemu w wyniku oddziaływania cyklicznych naprężeń mechanicznych. Jednakże w dziedzinie organicznych powłok ochronnych czynnik ten pozostaje niedoceniany. W pracy dokonano porównania wpływu cyklicznych naprężeń mechanicznych na nowe i pre-eksponowane (w podwyższonej temperaturze lub promieniowaniu UV) powłoki epoksydowe.