Filters
total: 7197
filtered: 6357
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: WAVE FILTERING
-
Diagnostics of bolted lap joint using guided wave propagation
PublicationThe paper presents numerical and experimental analyses of elastic waves propagation in a bolted lap joint. In experimental investigations condition assessment of the joint was performed with the use of symmetric waves excited by a piezoactuator. Numerical calculations were conducted in commercial finite element method software Abaqus. The influence of number of bolts and the value of the initial stress on recorded signals was examined....
-
Application of guided wave propagation in diagnostics of steel bridge components
PublicationEarly detection of potential defects and identification of their location are necessary to ensure safe, reliable and long-term use of engineering structures. Non-destructive diagnostic tests based on guided wave propagation are becoming more popular because of the possibility to inspect large areas during a single measurement with a small number of sensors. The aim of this study is the application of guided wave propagation in...
-
Nonlinear Properties of Seawater as a Factor Determining Nonlinear Wave Propagation
PublicationTaking practical advantage of nonlinear acoustical interactions occurring in seawater [1, 2] requires knowledge of the parameter of nonlinearity B=A of this medium. The literature does not offer much reports on B=A parameter value for seawater. In the few papers concerning that address the issue, results concerning ocean waters with high salinity and at large depths are given [3], while studies concerning seawater with low salinity...
-
Charge density wave and crystalline electric field effects in TmNiC2
PublicationSingle crystals of TmNiC2 were grown by the optical floating-zone technique and were investigated by x-ray diffraction (XRD), thermal expansion, electrical resistivity, specific heat, and magnetic susceptibility measurements. Single-crystal XRD reveals the formation of a commensurate charge density wave (CDW) characterized by a CDW modulation vector q2c = (0.5, 0.5, 0.5), which is accompanied by a symmetry change from the orthorhombic...
-
Jumping Wave Characteristic during Low Plasticity Burnishing Process
PublicationDuring the low plasticity burnishing process of soft materials such as carbon steel with a hardness of up to 40 HRC (Rockwell grade) a raised structure of the material known as the Jumping Wave forms in front of the tool roll. This phenomenon significantly disturbs the burnishing process, but is very poorly described in the literature. This article presents studies of this phenomenon on the example of burnished 1.0562 steel. The...
-
Vehicle Detection and Speed Estimation Using Millimetre Wave Radar
PublicationThe dataset titled Data from 76- to 81-GHz mmWave Sensor located at S7 road contains data recorded employing an IWR1642 mmWave sensor from Texas Instruments. The data comes from two sessions lasting 24h each. The dataset provides the possibility to perform analyses related to car traffic intensity on one of the carriageways of the motorway heading to the Gdańsk metropolitan area. Based on the gathered data, it is possible to calculate...
-
Preload monitoring in a bolted joint using Lamb wave energy
PublicationThe knowledge of the load in prestressed bolted connections is essential for the proper operation and safety of engineering structures. Recently, bolted joints have become an area of intensive research associated with non-destructive diagnostics, in particular in the context of wave propagation techniques. In this paper, a novel procedure of bolt load estimation based on the energy of Lamb wave signals was proposed. Experimental...
-
Numerical Study of Concrete Mesostructure Effect on Lamb Wave Propagation
PublicationThe article presents the results of the numerical investigation of Lamb wave propagation in concrete plates while taking into account the complex concrete mesostructure. Several concrete models with randomly distributed aggregates were generated with the use of the Monte Carlo method. The influence of aggregate ratio and particle size on dispersion curves representing Lamb wave modes was analyzed. The results obtained for heterogeneous...
-
Domain Reduction in Hybrid Technique for Electromagnetic Wave Scattering Problems
PublicationThis paper proposes a combination of the field matching technique, finite element method and generalized impedance matrix, the main idea of which is to reduce the computational domain by surrounding a scatterer with the smallest convex shape and applying the field matching technique. This approach can be applied for arbitrary shaped scatterers and types of materials and allows for the reduction of the computational domain. In order...
-
Simulation of Wave Propagation in Media Described by Fractional-Order Models
PublicationIn this paper, algorithms for simulation of the wave propagation in electromagnetic media described by fractional-order (FO) models (FOMs) are presented. Initially, fractional calculus and FO Maxwell's equations are introduced. The problem of the wave propagation is formulated for media described by FOMs. Then, algorithms for simulation of the non-monochromatic wave propagation are presented which employ computations in the time...
-
Nonlinear evolution of components of electromagnetic field of helicoidal wave in plasma
PublicationWyprowadzilismy model równań opisujących oddziaływanie pomiedzy kołowo spolaryzowanymi paczkami fal helikoidalnych w dwuwymiarowej plazmie. Dla quasi-jednowymiarowego przypadku otrzymaliśmy warunek nieliniowego rezonansu dla oddziaływania N-fal. Nowym ''osiągnięciem'' badań w kontekscie teorii solitonów, jest znalezienie rozwiązań dla przypadku asynchronizmu fal, które wydaje się być podstawowym dla paczek falowych nachylonych...
-
Longitudinal wave propagation. Part II, Analysis of crack influence
PublicationW pracy analizowano wpływ pęknięć zmęczeniowych na propagacje fali wzdłużnej w prętach. Opracowano nowe typy element ów spektralnych oparte na teorii elementarnej, Love'a, Mindlina i trójpostaciowej.
-
Longitudinal wave propagation. Part I - Comparison of rod theories
PublicationW pracy przedstawiono modele spektralnych elementów skończonych do analizy propagacji fali wzdłuznej w pretach. Opracowano modele wykorzystujace teorię elementarną, teorie Love'a, teorie Mindlina oraz teorię trójpostaciową.
-
Characterization of wave structures containing sets of bow-tie resonators
PublicationArtykuł opisuje metodę analizy rozpraszania fali elektromagnetycznej układzie rezonatorów motylkowych w strukturach otwartych i zamkniętych. W artykule zaprezentowano przykłady aplikacji układów mikrofalowych zawierające opisywane elementy.
-
Radiation phenomena from pseudochiral cylinders at plane wave incidence
PublicationPrzedstawiono wpływ materiałów pseudochiralnych na charakterystyki rozproszenia fali elektromagnetycznej od obiektów cylindrycznych. W celu zbadania zjawisk rozproszenia zastosowano kombinacje iteracyjnej procedury rozproszenia i metodę dopasowania rodzajów. Wpływ zastosowania materiałów pseudochiralych w konfiguracjach obiektów cylindrycznych zaprezentowano na charakterystykach pola rozproszonego w strefie dalekiej oraz na charakterystykach...
-
Damage detection in elements of strutures by the elastic wave propagation method.
PublicationW pracy przedstawiono wyniki badań dotyczace wykorzystania fal sprężystych do detekcji uszkodzeń i jedno i dwu wymiarowych elementach konstrukcyjnych.
-
Elimination of Impulsive Disturbances From Stereo Audio Recordings Using Vector Autoregressive Modeling and Variable-order Kalman Filtering
PublicationThis paper presents a new approach to elimination of impulsive disturbances from stereo audio recordings. The proposed solution is based on vector autoregressive modeling of audio signals. Online tracking of signal model parameters is performed using the exponential ly weighted least squares algo- rithm. Detection of noise pulses an d model-based interpolation of the irrevocably distorted sampl es is realized using an adaptive, variable-order...
-
THE APPLICATION OF KALMAN FILTERING TO PREDICT VERTICAL RAIL AXIS DISPLACEMENTS OF THE OVERHEAD CRANE BEING A COMPONENT OF SEAPORT TRANSPORT STRUCTURE
PublicationAs the devices designed to transport materials, the overhead cranes should meet certain geometric requirements for their operation to be safe. The presently available geodetic equipment, in particular total stations, provides opportunities for precise 3D measurements of coordinates of the controlled points. These coordinates make a basis for correcting the height of crane runway axes. The paper presents a method to calculate position...
-
Examination of the effect of altering model complexity on representing groundwater flow
PublicationW artykule przedstawiono wyniki badań na dokładnością modeli numerycznych przepływu wód podziemnych. Analizowano wpływ upraszczania struktury przestrzennej modelu na wyniki obliczeń.
-
Cold sintering of colloidal silica particles using different alkali solutions
Publication -
Ultrafast high-temperature sintering (UHS) of cerium oxide-based compound
PublicationUltrafast high-temperature sintering (UHS) is an innovative sintering technique that can densify ceramics in a few seconds, dramatically reducing the carbon footprint and firing costs. In this work, the feasibility of applying UHS in Gd-doped ceria (GDC) and GDC-Er-stabilized bismuth oxide (ESB) composite powders was investigated. At high UHS currents (22-24 A), a fully dense GDC sample with a large grain size was obtained. Nonetheless,...
-
Improvement of cooperation among SMEs and other stakeholders as means of fostering innovation
PublicationW artykule autorzy przedstawiają czynniki sprzyjające współpracy wśrod MSP i innych podmiotów rynkowych. Podejmują się również próby przedstawienia, w jaki sposób powyższe podmioty współpracują. Ponadto dokonują analizy wpływu współpracy na innowacyjność przedsiębiorstw.
-
Conducted emi identification in power electronic converters : modeling of EMI generation and propagation using circuit simulation and wiener filtering methods.
PublicationThis work presents the circuit simulations and the conventional signal processing technique (Wiener filtering) in order to reconstruct conducted ElectroMagnetic Interferences (EMI), generated and propagated in power electronics converters. In the simulation study, the most accurate presently available models of components of circuit have been used and improved. The proposed Wiener filtering method allows to identifying the transfer...
-
Design and Implementation of a Dual-band Filtering Wil-kinson Power Divider Using Coupled T-shaped Dual-band Resonators
PublicationThe paper introduces a novel structure of a dual-band filtering Wilkinson power divider (WPD). Its essential component is a dual-band bandpass filter (BPF), implemented using coupling lines and two T-shaped resonators. The BPF is incorporated into the divider structure to suppress the unwanted harmonics within the circuit. The latter is achieved owing to a wide stopband of the filter. The deigned dual-band WPD can suppress third...
-
An Experimental Investigation of Pressure Wave Celerity During the Transient Slurry Flow
PublicationTransportation of slurries in pressure pipelines is an example of a complex flow due to specific parameters of transported medium. For practitioners, the economy of designing and maintenance is usually the most important factor. For this reason, most of hydrotransport installations are fairly simple; however, they become more vulnerable to negative effects of the transient flow which can occur in pressure pipelines. As the consequence,...
-
Sensorless induction motor drive with voltage inverter and sine-wave filter
PublicationThis paper presents a speed sensorless control system of an induction motor with an output LC filter. It is known that the parameters design of the filter gives sine wave motor supply voltage but complicates control and estimation process. The reason is that the voltage drop and phase shift between filter input and output signals are imposed, and hence the motor voltages and currents differ from the inverter output waveforms. To...
-
Extreme bottom velocities induced by wind wave and currents in the Gulf of Gdańsk
Publication -
MEDIUM-TERM WAVE AND CURRENT MODELLING FOR A MESOTIDAL WADDEN SEA COAST
Publication -
Wind wave climate of west Spitsbergen: seasonal variability and extreme events
Publication -
Wave-induced bedload transport – a study of the southern Baltic coastal zone
Publication -
The expansion wave of an invasive predator leaves declining waterbird populations behind
Publication -
Lamb wave-based monitoring of shear failure of an adhesive lap joint
PublicationThe paper presents a study on the elastic wave propagation in adhesive joints of steel plates subjected to tensile loading. A single lap joint was chosen for analysis because of its simplicity and plurality of applications. Experimental investigations consisted of the uniaxial extension of prepared specimens. Force and displacement values were recorded by a testing machine. Simultaneously, guided Lamb waves were excited and signals...
-
System setup and software for cyclic, staircase and square wave voltammetry measurements
PublicationHardware dedicated for electrochemical measurement sometimes does not allow performing certain voltammetry experiments. Staircase and square wave voltammetry, techniques which have many advantages comparing with standard voltammetric techniques, are rarely implemented in software controlling electrochemical measuring equipment. These methods, however, can be relatively easy realized with some addition...
-
Design solution and selected research results of the sea-wave energy converter
PublicationW artykule przedstawiono oryginalne rozwiązanie konstrukcyjne boi do pozyskiwania energii fal morskich oraz analizy i badania modelowe turbiny wodnej poprzedzające wybór ostateczny konstrukcji modelu boi w skali 1:5 przewidzianego do badań eksperymentalnych w basenie holowniczym. Zaprezentowano także wybrane wyniki badań modelowych i symulacji komputerowych ukazujący wpływ systemu kotwiczenia i innych parametrów na jakość i efektywność...
-
Guided wave propagation for assessment of adhesive bonding between steel and concrete
PublicationAdhesive bonding is becoming more increasingly important in joining of structural elements. In civil engineering, there is a growing interest in connection by adhesive bonding in steel-concrete flexural members. This study concerns the guided wave propagation technique applied to condition assessment of an adhesive connection between a steel member and a concrete beam. Various states of degradation were considered by producing...
-
A novel formulation of 3D spectral element for wave propagation in reinforced concrete
PublicationThe paper deals with numerical simulations of wave propagation in reinforced concrete for damage detection purposes. A novel formulation of a 3D spectral element was proposed. The reinforcement modelled as the truss spectral element was embedded in the 3D solid spectral finite element. Numerical simulations have been conducted on cuboid concrete specimens reinforced with two steel bars. Different degradation models were considered...
-
Numerical investigation of the core eccentricity effect on wave propagation in embedded waveguide
PublicationThe paper presents results of theoretical and numerical investigation of guided wave propagation in two-layer bars with geometric imperfections in the form of eccentric location of steel core. Steel rod of diameter equal to 1 cm embedded in composite mortar-type cover with external diameter equal to 5 cm has been taken into consideration. Several different rods with variable size of eccentricity are analysed. Results for rods with...
-
Debonding Detection in Reinforced Concrete Beams with the Use of Guided Wave Propagation
PublicationOne of the most frequent damage of the reinforced concrete structures is debonding between steel bar and concrete cover. In the case of debonding occurrence not only the strength of the structure decreases, but also it is more vulnerable to corrosion damages. For this reason fast and effective methods of debonding detection in an early stage of its development need a significant boost. The paper presents analytical and experimental...
-
Guided Wave Propagation in Detection of Partial Circumferential Debonding in Concrete Structures
PublicationThe following article presents results of investigating the damage detection in reinforced concrete beams with artificially introduced debonding between the rod and cover, using a non-destructive method based on elastic waves propagation. The primary aim of the research was to analyze the possible use of guided waves in partial circumferential debonding detection. Guided waves were excited and registered in reinforced concrete...
-
Lamb Wave Based Structural Damage Detection Using Stationarity Tests
Publication -
Radiation phenomena from metamaterial cylinders at oblique plane wave incidence.
PublicationW pracy przedstawiono wpływ ujemnej przenikalności elektrycznej i magnetycznej rezonatorów cylindrycznych umieszczonych w wolnej przestrzeni na parametry rozproszenia. Wykorzystano zmodyfikowaną procedurę iteracyjną i metodę dopasowania rodzajów w celu badania fali rozproszonej od układu cylindrów przy ukośnym padaniu fali płaskiej.
-
Identification of discontinuites in composite rods and beams based on Lamb wave propagation
PublicationW pracy omówiono metodę identyfikacji typu nieciągłości w belkach i prętach kompozytowych, oparta o analizę zmain w propagacji fali Lamba.
-
Experimental an numerical investigation of wave propagation in composite beam with an additional mass
PublicationW pracy przedstawiono wyniki badań eksperymentalnych i symulacji numerycznych ilustrujace wpływ dodatkowej masy na propagacje fali Lamba w belce kompozytowej.
-
Verification of algorithms determining wave loads on support structure of wind turbine
PublicationThe offshore wind turbines require determination of wave loads on their support structure. This structure is fixed and, therefore, this problem is reduced to solving only the diffraction problem, which is determined by Laplace equation and conditions on the following boundaries: on the support structure, on the sea free surface and on its bottom, and at infinity on free surface. The linear problem was applied to determine the wave...
-
Impact of radio wave polarisation on off-body communications in indoor environments
PublicationThis paper describes the measurements and the analysis of the impact of radio wave polarisation on off-body communications in Body Area Networks in indoor environments. Measurements on polarisation impact are briefly described. Five investigated scenarios with different body postures and different antenna placements are characterised. The difference between the vertical and horizontal components of the received radio signal are...
-
Ground anchors diagnostic process based on elastic wave propagation method
PublicationThe paper is focused on analysis of elastic wave propagation in the context of diagnostics of ground anchors. Numerical simulations were performed to assess the possibility of evaluation of the anchorage quality. It was assumed that the quality and the load capacity of the anchor system directly depend on the length, on which mortar and steel cooperate.
-
Research on assessment of bolted joint state using elastic wave propagation
PublicationThe work contains results of experimental investigation of elastic wave propagation in a bolted single-lap joint. Tests were carried out for the excitation perpendicular to the connection plane. In experimental studies, PZT transducers were used for both excitation and registration of ultrasonic waves. The analyses took into account varying contact conditions between the elements of the connection depending on the value of the...
-
Design and Evaluation of the Compact and Autonomous Energy Subsystem of a Wave Energy Converter
PublicationThis paper presents the results of the design process focused on the development of the energy subsystem (ES) of a wave energy converter (WEC). The ES is an important electrical part that significantly affects the energy reliability and energy efficiency of the entire WEC device. The designed ES was intended for compact WECs powering IoT network devices working in the distributed grid. The developed ES is an electronic circuit...
-
Wave propagation modelling in 1D structures using spectral finite elements
PublicationW artykule omówiono modele propagacji fal wzdłużnych i poprzecznych w prętach oparte na dwóch sformułowaniach (w dziedzinie częstości i w dziedzinie czasu) metody elemntów spektralnych. Porównano otrzymane wyniki z wynikami eksperymentu.
-
Rectangular microstrip resonator illumi-nated by normal-incident plane wave
PublicationW pracy przedstawiono koncepcję modów oświetlających pozwalającą na obliczenie podstawowych parametrów elektrycznych anten mikropaskowych - częstotliwości rezonansowej, rezystancji promieniowania i charakterystyki promieniowania. Oparta jest ona na dwuwymiarowej metodzie przestrzeni widmowej, w której pobudzenie występuje w formie pojedynczej fali płaskiej padającej prostopadle na analizowaną strukturę. Rezultatem takiego podejścia...