Filters
total: 969
filtered: 399
Search results for: acicular grindable thermocouple
-
Performance of acicular grindable thermocouples for temperature measurements at sliding contacts
PublicationThe present study investigates the performance of acicular grindable thermocouples based on a constantan wire / steel hollow cylinder construction. The experiments showed that the measuring junction electrical resistance, temperature–voltage characteristic, measuring junction rise time and signal noise standard deviation of the acicular thermocouples are comparable to those of conventional J-type thermocouples with bare wire diameter...
-
Reliability of acicular grindable thermocouples for transient temperature measurements at sliding contacts
PublicationAcicular grindable thermocouples represent an interesting and prospective technique of temperature measurements at sliding contacts. This study aimed at the investigation of their reliability and accuracy as applied to the friction materials of various classes in contact with steel. The tests were conducted on a pin-on-disc tribometer under stationary and transient regimes. The experimental results were validated by comparing the...
-
Temperature Measurements at Tyre Tread Rubber on Sandpaper Oscillatory Sliding Contacts Using Acicular Grindable Thermocouples
PublicationThe tribological performance of tyre–road contacts depends crucially on the contact temperature. This study investigates the reliability and accuracy of acicular grindable thermocouples possessing an original needle-shaped wearable part as applied to measuring temperature at the oscillatory sliding contact between a rubber tyre tread sample and a sandpaper. A linear oscillatory tribometer is used to imitate the sliding phase of...
-
Measurement of temperature at sliding polymer surface by grindable thermocouples
PublicationThis paper is devoted to experimental study of capabilities and limitations of grindable thermocouples as applied to polymer materials sliding on metal. Chromel–alumel and chromel–copel grindable thermocouples have been developed and tested for wide ranges of contact pressure and sliding velocity. The background temperature of the sliding surface can be determined as the lower envelope of the signal from the grindable thermocouple....
-
A LABORATORY STAND FOR THE ANALYSIS OF DYNAMIC PROPERTIES OF THERMOCOUPLES
PublicationIn the present elaboration, problems connected with measurements of high variable temperatures of gases are introduced and the impact of dynamic properties of different construction solutions of thermoelements on the accuracy of the measurements is considered. A laboratory stand built within research under doctoral thesis, destined for analysis of dynamic properties of thermocouples is also described. Results of numerical simulation...
-
DETERMINING THE TIME CONSTANT USING TWO METHODS AND DEFINING THE THERMOCOUPLE RESPONSE TO SINE EXCITATION OF GAS TEMPERATURE
PublicationThis paper describes the two methods of determining the time constant of type K thermocouple, for two construction solutions: the exposed weld and the mantle fillet weld. This is an important parameter indicating the response time of the thermocouple on the recorded signal. The first method consists of determining the value of τ in the way of numerical simulation of heat exchange between the thermocouple and the current of gas...
-
Inverse determination of sliding surface temperature based on measurements by thermocouples with account of their thermal inertia
PublicationThis study developed an inverse heat conduction algorithm to determine temperature at a sliding surface taking account of thermocouple thermal inertia. The direct heat conduction problem was solved analytically based on the Laplace integral transform approach. The inverse algorithm was applied to the problem of friction of a brake material against a steel. The experiments were conducted on a pin-on-disc tribometer for three short-time...
-
An inverse algorithm for contact heat conduction problems with an interfacial heat source based on a first-order thermocouple model
PublicationInverse problems of contact heat conduction with an interfacial heat source are common in various fields of science, engineering and technology. In this study, an algorithm for their solution is developed based on an inverse parametric optimisation method with an impulse response function describing the heat partition and contact heat transfer. A first-order thermocouple model with a time constant parameter is embedded in the impulse...
-
Mathematical approach to design 3D scaffolds for the 3D printable bone implant
PublicationThis work demonstrates that an artificial scaffold structure can be designed to exhibit mechanical properties close to the ones of real bone tissue, thus highly reducing the stress-shielding phenomenon. In this study the scan of lumbar vertebra fragment was reproduced to create a numerical 3D model (this model was called the reference bone sample). New nine 3D scaffold samples were designed and their numerical models were created....
-
A Low-Profile 3-D Printable Metastructure for Performance Improvement of Aperture Antennas
PublicationIn order to increase the radiation performance of aperture-type antennas, this paper demonstrates a low-profile, planar, single-layer, three-dimensional (3-D) printable metastructure. The proposed hybridized metastructure is highly transparent as it is made out of novel hybrid meta-atoms having transmission coefficient magnitudes greater than -0.72 dB and fully complies with the near-field phase transformation principle. The hybridized...
-
Conductive printable electrodes tuned by boron-doped nanodiamond foil additives for nitroexplosive detection
PublicationAn efficient additive manufacturing-based composite material fabrication for electrochemical applications is reported. The composite is composed of commercially available graphene-doped polylactide acid (G-PLA) 3D printouts and surface- functionalized with nanocrystalline boron-doped diamond foil (NDF) additives. The NDFs were synthesized on a tantalum substrate and transferred to the 3D-printout surface at 200 °C. No other electrode...
-
Analytical method of determining dynamic properties of thermocouples used in measurements of quick – changing temperatures of exhaust gases in marine diesel engines
PublicationThe article presents selected issues of mathematical modeling of heat exchange between the thermocouple and the exhaust gas flowing them, in unsteady conditions. On the way of energy balancing consideration of thermodynamic processes developed differential equations describing the dynamic properties for three versions of the design sheathed thermocouples: with weld isolated from the sheath, with weld welded the sheath and with...
-
Circular colorings of graphs.
PublicationRozdział poświęcony jest cyrkularnemu modelowi kolorowania krawędzi. Rozważana jest zarówno wersja wierzchołkowa i krawędziowa. Szczególny nacisk położono na złożoność obliczeniową i zastosowania dla omawianych modeli kolorowania.
-
Differences in sequences between HBV-relaxed circular DNA and covalently closed circular DNA
Publication -
Ultimate distortion of circular saw
PublicationW artykule przedstawiono przyczyny i efekty poprzecznego odkształcenia piły tarczowe. Przedstawiono również zależność, na podstawie której wyznaczyć można graniczną wartość odkształcenia piły tarczowej.
-
Static stiffness of circular saw
PublicationW pracy przedstawiono metodę pomiaru i przykład wyników badań doświadczalnych sztywności statycznej piły tarczowej.
-
Analysis of circular cavity with cylindrical objects
PublicationArtykuł opisuje analizę rozpraszania fali elektromagnetycznej na obiektach cylindrycznych rozmieszczonych dowolnie w strukturze rezonatora. Analiza oparta jest na metodzie dopasowania rodzajów. Dokładność i poprawność metody jest zweryfikowana poprzez porównanie uzyskanych wyników z wynikami otrzymanymi z metod alternatywnych i własnych pomiarów wykonanych układów.
-
Circular saw vibrations or dynamics of the spindle
PublicationSawing of wood with circular saws is a typical example of cutting with multi-blade tools. In that kind of cutting, theposition accuracy of following tool blades is a crucial factor which affects the cutting process and machining final effects.Position tooth errors may cause deterioration in cutting conditions, changes in loads of individual teeth and the tool as a whole,and also a decrease in accuracy and surface quality after...
-
Circular saws with closed chip grooves
PublicationW pracy przedstawiono analizę wpływu kształtu rowków wiórowych ostrzy piły tarczowej na sposób odprowadzania wiórów ze strefy skrawania. Zaprezentowano rozwiązanie konstrukcyjne piły tarczowej z domkniętymi rowkami wiórowymi
-
A simple model of circular hydraulic pump
PublicationRozpatrzono warunki powstawania osiowosymetrycznego uskoku hydraulicznego. Przedstawiono model, w którym rozpatrzono obecność dodatkowych strat w równaniu Bernoulliego. Przyczyniają się one do powstawania dodatkowego wiru w miejscu uskoku. Porównanie z wynikami badań eksperymentalnych potwierdza słuszność przyjętych tez.
-
Axsial run-out circular saws
PublicationW pracy przedstawiono podstawowe przyczyny i efekty bicia osiowego ostrzy pił w układzie przecinania na pilarkach tarczowych.
-
Outlet Flow Velocity In Circular Culvert
PublicationThe outlet flow velocity in the end section of the culvert barrel depends in most cases on the culvert geometry, including the barrel slope, as well as on upstream and downstream channel parameters. Flowing water can create pressure flow or free surface flow in the culvert barrel. In the case of an unsubmerged barrel outlet, the free-surface flow is more frequent than the full flow. Increased velocities can cause channel bed scour...
-
Inspection of circular saw teeth quality
PublicationDokładność geometryczna ostrzy piły tarczowej znacząco wpływa na efekty przecinania i odgrywa znaczacą rolę w ekonomice każdego zakładu przerobu drewna. Ocena jakości piły jest możliwa na bazie monitorowania dokładności geometrycznej każdego ostrza piły. Opracowany do tego celu wizyjny kontroler ostrzy pił tarczowych został przedstawiony w artykule.
-
Static stiffness of blades in circular saw
PublicationW pracy przedstawiono sposób wyznaczania sztywności statycznej pił tarczowych. Przedstawiono również czynniki wpływające na jej wartość.
-
The reduction of vibrations in circular sawing machines
PublicationThe presented in this paper the main objectives of the research were to explore vibrations signals of the main spindle system, the machine tool body and a circular saw to extract informative features for assessment of the designs of the panel saw Fx3 and its follower Fx550.Even though the main spindle of the new table sliding saw Fx550 has its rotational speeds larger about 20% in comparison to the Fx3, peak values of the vibrational...
-
Effects of Sterilization Methods on Different 3D Printable Materials for Templates of Physician-Modified Aortic Stent Grafts Used in Vascular Surgery—A Preliminary Study
Publication -
T-colorings, divisibility and circular chromatic number
PublicationLet T be a T-set, i.e., a finite set of nonnegative integers satisfying 0 ∈ T, and G be a graph. In the paper we study relations between the T-edge spans espT (G) and espd⊙T (G), where d is a positive integer and d ⊙ T = {0 ≤ t ≤ d (max T + 1): d |t ⇒ t/d ∈ T} . We show that espd⊙T (G) = d espT (G) − r, where r, 0 ≤ r ≤ d − 1, is an integer that depends on T and G. Next we focus on the case T = {0} and show that espd⊙{0} (G) =...
-
MACHINE VISION DETECTION OF THE CIRCULAR SAW VIBRATIONS
PublicationDynamical properties of rotating circular saw blades are crucial for both production quality and personnel safety. This paper presents a novel method for monitoring circular saw vibrations and deviations. A machine vision system uses a camera and a laser line projected on the saw’s surface to estimate vibration range. Changes of the dynamic behaviour of the saw were measured as a function of the rotational speed. The critical rotational...
-
Dynamics of the total system of the circular sawing machine
PublicationW pracy przedstwaiono przyczyny i efekty zmiany położenia ostrzy piły tarczowej. Opisana metoda pomiaru zachowania dynamicznego piły pozwala uzytkownikowi okreslic przyczyny drgań. Ponadto, może wskazać drogi efektywnej ich minimalizacji.
-
Determination of optimal rotational speeds of circular saws
PublicationW pracy przedstawiono możliwości diagnostyczne stanowiska HewSaw do badania zachowania się pił w funkcji prędkości obrotowej piły. Wykazano, ze wyznaczone wartości prędkości optymalnych badanych pił leżą poniżej wartości zalecanych przez producenta. Praca z prędkościami wyższymi od optymalnych może prowadzić do zwiększenia strat materiałowych, a także stwarzać zagrożenia dla obsługi.
-
On the Absolute Stereochemistry of Tolterodine: A Circular Dichroism Study
Publication -
Circular saw blade dynamics - the measurement method
PublicationW pracy przedstawiono przyczyny i efekty zmiany położenia ostrzy piły tarczowej w układzie przecinania. Przedstawiony sposób pomiaru dynamiki piły tarczowej umożliwia określenie przyczyn drgań, co stanowi podstawę skutecznej ich minimalizacji.
-
Dipole matrix for the 2D inclusions close to circular
Publication -
Dynamics of the circular sawing machine spindle system
PublicationW pracy przedstawiono wyniki badań wpływu prędkości obrotowej na dynamikę układu wrzecionowego pilarki tarczowej. Czynnikami badanymi były bicie osiowe i promieniowe wrzeciona, które mierzono za pomocą czujników wiroprądowych na kierunku działania przekładni pasowej, a także na kierunku do niego prostopadłym. Przeprowadzone badania eksperymentalne wykazały, że wartość prędkości obrotowej wrzeciona oraz sposób przekazywania mocy...
-
Analysis of circular cavity with tunable combline resonator
PublicationArtykuł prezentuje analizę rozpraszania fali elektromagnetycznej na obiekcie cylindrycznym umieszczonym we wnęce rezonansowej. Metodą analizy jest metoda dopasowania rodzajów.
-
Precision of cutting system in circular sawing machine
PublicationW pracy przedstawiono analizę dokładności układu przecinania pilarki tarczowej, w której uwzglednoino dokładność struktury geometryczno- ruchowej przecinarki.
-
Assessment of radial run-out of circular saw.
PublicationW pracy przedstawiono ocenę bicia promieniowego pił tarczowych na podstawie analizy zróżnicowania przekrojów warstw skrawanych przez poszczególne ostrza piły
-
Viscoplastic analysis of damped vibrations of circular plate
PublicationGłównym celem artykułu jest przedstawienie procedury do nieliniowej statycznej i dynamicznej analizy MES z lepkoplastycznym prawem Bodnera-Partoma. Przedstawione są podstawowe równania modelu konstytutywnego wraz z koncepcją implementacji do komercyjnego programu MSC.Marc przy użyciu procedury UVSCPL. Przedstawiono przykład analizy numerycznej płyty kołowej, zweryfikowany eksperymentalnie. Dodatkowo przedstawiono koncepcje wyznaczania...
-
Circular saw teeth control with vision method
PublicationOpisano automatyczne urządzenie do automatycznego sprawdzania geometrii pił tarczowych WKOPTar. Określono błędy pozycjonowania ostrzy piły, której obrót jest sterowany w sposób automatyczny z wykorzystaniem obrazu ostrzy z kamery rejestrującej obraz powierzchni przyłożenia. Zaprezentowano szereg wyników pomiarów dokładności wykonania ostrzy piły.
-
Plane wave scattering by an array of circular cylinders
PublicationMetodę dopasowania rodzajów zastosowano do połączenia zastępczego pola rozproszonego od dowolnej konfiguracji dwuwarstwowych prętów ferrytowych i dielektrycznych z pobudzeniem falą płaską. Zaprezentowano charakterystyki rozpraszania zarówno w strefie dalekiej jaki i bliskiej dla kilku konfiguracji prętów przy pobudzeniu falą płaską.
-
Economical wood sawing with circular saw blades
PublicationMaterial- and energy-saving belong to the basic requirements which are imposed on the contemporary manufacturing processes. Since realization of those processes gives measurable profits not only economical but also ecological. In case of wood sawing with circular saw blades material- and energy-savings are dependent on total overall set of teeth (theoretical kerf) and teeth position accuracy in relation to the workpiece. Hence,...
-
Chladni and circular saw disc vibrations visualisation
PublicationIn this paper are described some methods for saw disc vibration monitoring in march of time (chronology). Ernst Chaldni, the father of sound visualisation and his patternsis are mentioned. In the last partof article are introduced results received with authors measuring systems.
-
ICT-enabled circular economy: conceptualising the links
PublicationThis chapter sets conceptual backgrounds regarding the potentially emerging causal links between digital technologies and circular economy ideas implementation. We argue that digital technologies may constitute an effective element enabling the transformation from linear to circular and environmentally friendly economic activities. This work draws the general picture at the macro and micro level. The macro perspective shows how...
-
Design optimization of novel compact circular polarization antenna
PublicationThe paper describes a structure and a design optimization procedure of a miniaturized circular polarization antenna with elliptical ground plane slots and feed line with stepped-impedance stubs. Constrained optimization of all antenna parameters is executed in order to explicitly reduce the antenna size while maintaining required impedance axial ratio bandwidth of 5 GHz to 7 GHz at the same time. The size of the optimized antenna...
-
The Influence of Articular Cartilage Thickness Reduction on Meniscus Biomechanics
PublicationObjective Evaluation of the biomechanical interaction between meniscus and cartilage in medial compartment knee osteoarthritis. Methods The finite element method was used to simulate knee joint contact mechanics. Three knee models were created on the basis of knee geometry from the Open Knee project. We reduced the thickness of medial cartilages in the intact knee model by approximately 50% to obtain a medial knee osteoarthritis...
-
Stress analysis of a strip under tension with a circular hole
PublicationThe paper addresses stress analysis of a strip with a circular hole under uniform uniaxial tension based oncircumferential stress expressionρπ. Stresses are analyzed in the infinite-length strips under tension with holes, the ratioof the hole radiusa to the strip half-widthb is either equal to:κ =a/b = 0.1 orκ = 0.5. Circumferential stresses aredetermined in selected cross-sections of the strip. The stress diagrams display local...
-
Mechatronic system for automatic inspection of circular saw teeth
PublicationArtykuł prezentuje system mechatroniczny do automatycznej oceny geometrii ostrzy pił tarczowych. Opisywany system wizyjny został zastosowany w automatycznym kontrolerze ostrzy pił tarczowych WKOPTar. Wrzeciono urządzenia posiada swój napęd sterowany bezstopniowo obrazem ostrzy i zapewnia powtarzalne pozycjonowanie ostrzy w celu przechwycenia ich obrazów, które są następnie analizowane z wykorzystaniem specjalnego oprogramowania....
-
Monitoring of the circular saw vibrations with machine vision system.
PublicationPraca przedstawia metodologię wyznaczania drgań obracających się pił tarczowych z wykorzystaniem technik wizyjnych. Na podstawie otrzymanych wyników można wyznaczyc prędkości krytyczne piły oraz podac obszary prędkości zalecanych (najmniejsze wartości drgań poprzecznych piły).
-
Geometrical effects of axial run-out in circular saws
PublicationW pracy omówione zostały efekty geometryczne jakie wywoływane są przez błąd bicia osiowego pił tarczowych.
-
The circular chromatic index of some class 2 graphs
PublicationW artykule został wyznaczony cyrkularny indeks chromatyczny dla dwóch rodzin grafów klasy 2. Co więcej, podano nie trywialne oszacowania tego parametru dla snarków Isaacsa i Goldberga. Na koniec artykułu rozważana jest złożoność obliczeniowa problemów związanych z cyrkularnym kolorowaniem krawędzi.