displaying 1000 best results Help
Search results for: STEEL PILES
-
Microstructural and Mechanical Properties of Novel Co-Free Maraging Steel M789 Prepared by Additive Manufacturing
Publication -
Modelling and parameter identification of steel–concrete composite beams in 3D rigid finite element method
Publication -
Performance of Vector-valued Intensity Measures for Estimating Residual Drift of Steel MRFs with Viscous Dampers
PublicationViscous Dampers (VDs) are widely used as passive energy dissipation system for improving seismic performance levels especially in retrofitting of buildings. Residual Inter-story Drift Ratio (R-IDR) is another important factor that specifies the condition of building after earthquake. The values of R-IDR illustrates the possibility of retrofitting and repairing of a building. Therefore, this study aims to explore the vector-valued...
-
Assessment of technical condition and repair of steel structure elements on the example of fire damage in a warehouse building
PublicationThe paper analyses a case study on the structural assessment of warehouse building partially damaged by fire caused by external source (fire of lorries close to the building). The authors focus on the site investigations and laboratory test results prior to assessing actual condition of the structural elements. Both strengthening concept and repair procedure of a steel column are addressed here. A short literature survey in the...
-
Influence of laser processing of the low alloy medium carbon structural steel on the development of the fatigue crack
PublicationThe paper contains the results of the structural analysis, hardness tests and fatigue tests conducted for the medium carbon structural steel with low content of Cr and Ni after its processing with CO2 laser beam. Pre-cracks were made in the round compact tension (RCT) specimen used for fatigue test. Next, four paths, parallel to each other, were melted on both sides of the samples using a laser beam. The paths were perpendicular...
-
Impact of Tensile and Compressive Stress on Classical and Acoustic Barkhausen Effects in Grain-Oriented Electrical Steel
PublicationIn this paper, we present the results of the investigation of impact of tensile and compressive stress on the classical Barkhausen effect, magnetoacoustic emission (MAE) signal properties, and B(H) hysteresis loops for grain-oriented (GO) electrical steel. Samples have been glued to a nonmagnetic steel bar and stressed within elastic range (±800 μdef) by means of four-point bending method. The samples were cut out in two directions...
-
Influence of the laser remelting parameters on the thickness of surface layers created on the stainless steel X5CrNi18-10
PublicationIn this work the surface of austenitic stainless steel type X5CrNi18-10 was treated by using laser. Laser remelting was done by means of laser MLT 2500 CO2 with different parameters of treatment: P - power beam (800 [W], 1000 [W], 1100 [W], 1200 [W]); v - scanning velocity (6 [mm/s], 7 [mm/s], 8 [mm/s]); diameter of laser beam (1.4 [mm], 1.6 [mm]). The influence of these parameters on the thickness and shape of layers in manufacturing...
-
The determination of deformations and stresses of laser welds used for fatigue assessment of steel sandwich panel joints
PublicationPanele typu sandwich znajdują szerokie zastosowanie w wielu gałęziach przemysłu. W przypadku niektórych zastosowań wymagających ocenę ryzyka dużą rolę odgrywa ocena trwałości zmęczeniowej spoin laserowych paneli. W pracy prezentowane są metody wyznaczania lokalnych odkształceń i naprężeń w połączeniach spawanych w celu oceny trwałości zmęczeniowej według hipotez lokalnych naprężeń i odkształceń.
-
Numerical investigation on dynamic performance of a multi-storey steel structure model and comparison with experimental results
PublicationShaking table testing is the most commonly adopted method to simulate earthquake forces. This approach allows us to analyze the dynamic performance and provides a valuable insight into the dynamics of building structures, which helps to improve their future safety and reliability. The present study aims to conduct a numerical evaluation of dynamic response of a multi-storey steel structure model, which was previously examined during...
-
Numerical Analysis of a Steel Frame Building with Soft-storey Failure under Ground Motion Excitation
PublicationThe aim of this paper is to show the results of a numerical analysis focused on the behaviour of multi-storey steel frame building that suffers from a soft-storey failure under ground motion excitation. A numerical model of the structure was created in FEM computer software and was exposed to an impact that would have been generated after a soft-storey failure due to falling of the upper floors. During the analysis, the whole structure...
-
Evaluation of porous ferritic Fe22Cr stainless steel for solid oxide fuel cells at high temperature
PublicationW pracy przedstawiono wyniki badań korozji stali Fe22Cr w wysokich temperaturach.
-
Effect of the Post-Weld Surface Condition on the Corrosion Resistance of Austenitic Stainless Steel AISI 304
PublicationSurfaces of welded elements made of corrosion-resistant (stainless) steels develop temper colours. The removal of thickened oxide layers off steels exposed to temperatures below 300°C is necessary and entails the restoring of high corrosion resistance of the stainless steel. The article presents tests concerned with the effect of a method applied to remove post-weld temper on the corrosion resistance of austenitic stainless steel...
-
Experimental research on over-laminated steel sandwich panel connection to determine the form of fatigue failure
PublicationThe novel means of transport need to meet rising both the economic and ecologic requirements. In recent years the International Maritime Organization (IMO) introduced new measure of ship energy efficiency (the EEDI index), as well as new regulations regarding higher quality of fuel (so called Tier limits). It resulted in much higher interest of the technological development of ships. One of the solution having great potential is...
-
Application of wavelet transform in analysis of guided wave propagation signals for damage detection in a steel plate
PublicationThe paper presents results of experimental investigations on damage detection using guided wave propagation technique. The tested specimen was a steel plate with a defect in the form of a rectangular notch. Lamb waves were excited by a PZT actuator and sensed by a laser vibrometer. Since reflections from damage in registered signals are often masked by measurement noise, for identification of time of reflections from damage, continuous...
-
Numerical Investigation on Dynamic Performance of a Multi-storey Steel Structure Model and Comparison with Experimental Results
PublicationShaking table testing is the most commonly adopted method to simulate earthquake forces. This approach allows us to analyze the dynamic performance and provides a valuable insight into the dynamics of building structures, which helps to improve their future safety and reliability. The present study aims to conduct a numerical evaluation of dynamic response of a multi-storey steel structure model, which was previously examined during...
-
Improved Performance of 1-Ethyl-3-Methylimidazolium Tetrafluoroborate at Steel/HCl Interface by Iodide Ions
PublicationThe corrosion and corrosion inhibition of St37 steel in 0.1 M HCl solution by 1-ethyl-3-methylimidazolium tetrafluoroborate (EMITFB) and the effect of addition of KI on the inhibitive performance of EMITFB have been examined by electrochemical [electrochemical impedance spectroscopy, potentiodynamic polarization, and dynamic electrochemical impedance spectroscopy (DEIS)] and surface examination [scanning electron microscope (SEM)...
-
Potential and strain rate impact on the electrochemical properties of 304L stainless steel under tensile stresses.
PublicationPraca skupia się na badaniach aspektu elektrochemicznego i mechanicznego pękania warstwy pasywnej obecnej na stali 304L. Przedstawione zostały wyniki chwilowych zmian impedancji oraz zmiany parametrów elektrochemicznych warstwy pasywnej podczas testów rozciągania przy różnych poziomach polaryzacji anodowej oraz szybkości rozciągania. Na ich podstawie można stwierdzić, że zarówno czynnik elektrochemiczny, jak i mechaniczny wpływają...
-
Cavitation erosion behavior of 18/8 stainless steel after its laser alloying of manganese
PublicationW pracy przedstawiono badania kawitacyjne stali austenitycznej 18/8 po laserowym stopowaniu jej powierzchni różną zawartością manganu. Oceniano podatnoś stopowanej powierzchni do odkształceniowego umacniania pod wpływem obciążeń kawitacyjnych oraz głębokość umocnienia.
-
Suspension and process parameters selection for electrophoretic deposition of Mn–Co spinel coating on steel interconnects
PublicationMetallic interconnect coatings, consisting of MnCo2O4 spinel, were effectively applied to Crofer 22 APU using the electrophoretic deposition (EPD) method in both H2O: ethanol and pure ethanol solvents. The primary goal of this method was to prevent chromium migration, minimize evaporation, and control the oxidation rate. The study aimed to assess the quality, adhesion, and thickness of the Mn–Co coating, with the objective of...
-
Finite-element analysis of a base-isolated multi-storey steel building under seismic motions
PublicationNumerical simulation of the seismic behaviour of a multi-storey steel building, both fixed-base and base-isolated, under the 1940 El Centro earthquake was performed in this paper. The analyzed 4-storey building was decoupled from the shaking ground with the Polymeric Bearings, which can be considered a proposal of a new seismic isolation system. It consists of rectangular-shaped blocks made of a specially prepared flexible polymeric...
-
Influence of separation gap on the response of colliding models of steel structures under seismic and paraseismic excitations
PublicationAs a result of high urbanization, the need to erect closely-spaced buildings forces designers to consider collisions between structures taking place during ground motions. Experimental and numerical studies have confirmed that such collisions (often referred to as structural pounding) may cause serious damage to the structural elements and even lead to total collapse of colliding structures. The main reason of earthquake-induced...
-
Safety of erection and repair of steel tanks with geometric imperfections using heavylift jack-up system
PublicationSafety analysis is performed of cylindrical vertical steel tanks during erection using heavylift jack up system. During an assembly or repair process a set of hydraulic supports is used. It allows to use the in-place lifting of heavy steel constructions on the required height. Wind can strongly influence stability of the lifted tank. Any geometric imperfections can reduce the critical or limit load. In the work failures of the...
-
Fracture Surface Topography Parameters for S235JR Steel Adhesive Joints After Fatigue Shear Testing
PublicationThis paper presents the experimental results of a study investigating the effect of holes and notches made on the overlap ends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets bonded with Araldite 2024-2 epoxy adhesive were tested. For comparative reasons, static shear strength tests and high-cycle fatigue strength tests were performed. Adhesive-filled joints having three holes, each with a diameter...
-
High-temperature kinetics study of 430L steel powder oxidized in air at 600–850 °C
PublicationThe 430L stainless steel powder with a mean particle size of 95 μm was studied to determine its high-temperature oxidation properties. Continuous thermogravimetric measurements were carried out for 100 h in air at temperatures in the range of 600–850 °C. Even though a considerable amount of Cr (up to ˜5 wt.% Cr) inside the grains was depleted – especially inside small grains – no breakaway oxidation was observed. This indicates...
-
Cyclic deformation and fracture behaviour of additive manufactured maraging steel under variable-amplitude loading
PublicationThe cyclic deformation and fracture behaviour of 18Ni300 maraging steel produced by laser beam powder bed fusion is studied under variable-amplitude loading. The tests were conducted under fully-reversed strain-controlled conditions with a loading sequence comprising three ascending cycles and three descending cycles repeated sequentially until failure. After the tests, fracture surfaces were examined using height and volume surface...
-
Evaluation of time and space distribution of magnetic flux density in a steel plate magnetized by a C-core
PublicationBadano wpływ częstości magnesowania płyty stalowej na rozkład przestrzenny indukcji magnetycznej wewnątrz tej płyty. Rozkład ten oceniano na podstawie pomiaru natężenia emisji magnetoakustycznej a także rozkładu na powierzchni płyty natężenia efektu Barkhausena. Wyniki dyskutowane są ilościowo i porównane z wynikami modelowania metodą elementów skończonych, w której uwzględniono efekt powstawania prądów wirowych.
-
Cavitation erosion behavior of 18/8 stainless steel after its laser alloying of manganese
PublicationW pracy przedstawiono wyniki badań własności kawitacyjnych stali nierdzewnej gatunku 18/8 po jej laserowym stopowaniu różną zawartością manganu. Stwierdzono, że przy zawartości Mn w ilości 7,13% występuje największy wzrost twardości po stopowaniu a głębokość umacniania na skutek działania obciążeń kawitacyjnych jest najmniejsza.
-
Environmental degradation of the Cr-Mo steels in liquid hydrocarbons
PublicationPrzedstawiono podatność stali stopwych 26H2MF i 34HNM do naprężeniowego pękania korozyjnego. Środowiskiem do badań było paliwo ciężkie i zużyty olej mineralny.
-
Hydrogen degradation of structural steels in technical hydrocarbon liquids
PublicationDla stali stopowych przeprowadzono badania absorpcji wodoru, mechaniczno-korozyjne przy stałej małej prędkości odkształcania, przy stałym obciążeniu i przy obciążeniu cyklicznie-zmiennym. Środowiskiem było paliwo kotłowe, przepracowany olej mineralny oraz gliceryna. Stwierdzono, iż pochłonięty wodór nie powoduje przedwczesnego zniszczenia stali poddanych działaniu stałego obciążenia ponizej granicy plastyczności oraz, że zaabsorbowany...
-
Corrosion behavior of vacuum sintered duplex stainless steels
Publication -
The corrosion resistance of laser surface alloyed stainless steels
Publication -
Weldability of high strength steels in wet welding conditions
PublicationIn this paper are characterized problems of high strength steel weldability in underwater wet welding conditions. Water as a welding environment intensifies action of unfavourable factors which influence susceptibility to cold cracking of welded steel joints. The susceptibility to cold cracking of S355J2G3 steel and S500M steel in wet conditions was experimentally estimated (by using Tekken test). It was concluded that the steels...
-
Hydrogen degradation of high strength low alloyed steels.
PublicationBadano wpływ polaryzacji katodowej na własności stali węglowej, stali o podwyższonej i wysokiej wytrzymałości metodą stałego powolnego odkształcania.Stwierdzono, że stopień kruchości wodorowej każdej z badanych stali zależał od stężenia wodoru dyfuzyjnego.
-
Investigations of welded joints of dissimilar heat resistant steels.
PublicationPrzeprowadzono badania metalograficzne połączeń spawanych różnorodnych stali żarowytrzymałych rur o przekroju 31,8x7,1 mm ze stali 10H2M z blachą ze stali 20H23N18. Badania makro- i mikrostruktury złączy spawanych wykazały, że istotnym czynnikiem wpływającym na właściwości mechaniczne złącza jest obecność wad takich jak pory lub wtrącenia żużla. Te nieciągłości w materiale powodują koncentrację naprężeń i powstawanie mikropęknięć.
-
The Application of Cluster Analysis in the Assessment of the Weldability of Unalloyed Steels
PublicationNon-alloy steels constitute a large group of steels characterised by diversified chemical composition, structural morphology and a wide range of mechanical properties (determining weldability). The paper presents results of multidimensional analyses (based on cluster analysis) of 110 selected unalloyed steel grades. Properties adopted as diagnostic features included the chemical composition, mechanical properties (yield point)...
-
Hydrogen degradation of high-strength weldable steels in seawater
PublicationOceniono podatność na niszczenie wodorowe stali spawalnych o wysokiej wytrzymałości przy obciążeniach monotonicznie rosnących. Badano dwa gatunki stali ulepszonych cieplnie i ich złącza spawane. Przeprowadzono próby rozciągania z małą prędkością odkształcania w wodzie morskiej przy polaryzacji katodowej. Wykonano próby przenikania wodoru metodą Devanathana-Stachurskiego.
-
Hydrogen delayed cracking of high-strength weldable steels
PublicationOceniano podatność na niszczenie wodorowe stali 14HNMBCu o wysokiej wytrzymałości i jej połączeń spawanych przy obciążeniu stałym w wodzie morskiej. Badania przeprowadzono w powietrzu, oraz w środowisku wody morskiej przy potencjale korozyjnym i przy polaryzacji katodowej. Obecność lub brak opóźnionych pęknięć próbek z karbem przyjęto za miarę odporności na niszczenie wodorowe przy stałym obciążeniu.
-
Influence of process of straightening ship hull structure made of 316L stainless steel on corrosion resistance and mechanical properties
PublicationThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries, for architectural elements, and many others. The chemical composition of corrosion-resistant...
-
Vplyv modifikácie dubovégo dreva technólogiou thermo-wood na zrnistosŤ piliny z procesov pilenia dreva na rámovej pile PRW 15M
PublicationW referacie przedstawiono wpływ modyfikacji termicznej drewna dębowego technologią ThermoWood na ziarnistość wiórów z procesu przecinania na pilarce ramowej PRW15M. Stwierdzono, że trociny uzyskane z drewna dębowego modyfikowanego termicznie nie zawierają w swoim składzie szkodliwych dla układu oddechowego człowieka cząstek z frakcji PM2.5, a ponadto nie wykryto cząstek frakcji PM10, które mogłyby tworzyć smog w środowisko pracy.
-
Evaluation of cavitation erosion–corrosion degradation of mild steel by means of dynamic impedance spectroscopy in galvanostatic mode
Publication -
Experimental validation of the use of energy transfer ratio (ETR) for damage diagnosis of steel-concrete composite beams
Publication -
Strengthening mechanism and precipitate evolution of a multi-application special engineering steel designed based on a hybrid idea
Publication -
Experiments and Numerical Simulations of the Annealing Temperature Influence on the Residual Stresses Level in S700MC Steel Welded Elements
Publication -
Appliance of High Speed Camera during Industrial Exploitation on the Example of Static and Dynamic Tests of Steel Probes
Publication -
Numerical analysis of influence of intermediate stiffeners setting on the stability behaviour of thin-walled steel tank shell
Publication -
Comparison of properties of magnetoacoustic emission and mechanical Barkhausen effects for P91 steel after plastic flow and creep
PublicationW artykule przedstawiono wyniki pogłębionej analizy sygnału szumowego efektu Barkhausena dla próbek ze stali krzemowej Fe-2%Si po deformacji plastycznej. Badane były próbki po walcowaniu na zimno powodującym odkształcenie względne w zakresie do 8%. Pierwsze podejście polegało na analizie w dziedzinie czasu widma badanego sygnału. Analiza ta została uzupełniona o analizę liczby zliczeń impulsów w funkcji napięcia progowego, zarówno...
-
Niszczenie wodorowe złączy spawanych ze stali S355 = Hydrogen degradation of welded joints of S355 steel
PublicationW artykule przedstawiono ocenę podatności na niszczenie wodorowe złączy spawanych ze stali S355. Jako parametry niszczenia wodorowego wybrano względne wartości energii zniszczenia, wydłużenia, przewężenia i wytrzymałości na rozciąganie. Parametry te wyznaczono w próbie odkształcania z małą prędkością na próbkach okrągłych, gładkich. Stwierdzono, że stal S355w środowisku kwaśnym podczas polaryzacji katodowej, jest bardziej skłonna...
-
Complex Corrosion Properties of AISI 316L Steel Prepared by 3D Printing Technology for Possible Implant Applications
Publication -
Surface Layer Properties of Sintered Ferritic Stainless Steel Remelted and Alloyed with FeNi and Ni by HPDL Laser
Publication -
Laser Thermal Oxidation by Ytterbium-Doped Fibre Laser of the Hot and Cold-Rolled Stainless Steel Surface
Publication