Search
Search results for: UNDERGROUND PIPE
-
The effect of thermal modification on the quality of the milled surface of beech and pine wood
PublicationThe article deals with the effect of thermal modification on the quality of the created surface during milling on CNC milling cutters. The quality of the created surface is evaluated based on surface roughness, specifically its roughness parameter Ra. The observed surface is created by a shank cutter with a diameter of 20 mm and three cutting edges in a spiral at a standard speed of 18,000. min-1. The article compares thermally...
-
Determination of the bearing capacity of pile foundations based on CPT test results
PublicationAnalityczne określanie pełnej krzywej obciążenie - osiadanie na podstawie parametrów geotechnicznych wciąż stanowi bardzo trudne zadanie naukowe i inżynierskie. W pracy przedstawiono metodę bezpośredniego wykorzystania oporów na stożku sondy statycznej do określania pełnej krzywej osiadania dla pali Vibro-Fundex. W sumie jako materiał weryfikacyjny wykorzystano 94 próbne obciążenia statyczne pali.
-
Effect of pine essential oil and rotating magnetic field on antimicrobial performance
Publication -
Estimation of Screw Displacement Pile-Bearing Capacity Based on Drilling Resistances
PublicationThis article presents an engineering, empiricalmethod of estimating the bearing capacity and settlementcharacteristics Q-s of screw displacement piles andcolumns, based on soil resistance encountered during thedrilling to form piles/columns in the ground. The methodwas developed on the basis of correlation analyses of thetest results of 24 piles made during the “DPDT-Auger”research project (Krasiński et al., 2022a). In the proposedmethod,...
-
EVALUATION OF CAUSES OF CORROSION OF HEATING PIPES AND BALLAST CHAMBERS ON HLVJ INNOVATION
Publication..
-
Numerical simulation of screw displacement pile interaction with non-cohesive soil
PublicationA trial numerical simulation of screw displacement pile interaction with non-cohesive subsoil during the transfer of compression load. The simulation was carried out in an axisymmetric system. The technological phases of pile installation in the ground were numerically modelled using equivalent processes which provided similar effects to real technical actions. The results of the numerical calculations were verified by comparing...
-
Probabilistic analysis of settlements under a pile foundation of a road bridge pylon
PublicationThe paper addresses the reliability change of a road bridge pile foundation due to the unpredictable increase of settlements in time. The analysis is based on the Rędziński Bridge in Wrocław, Poland, its design assumptions, and monitoring results. The bridge foundation rests on a multi-layered subsoil assumed random. The Finite Element model of the subgrade is generated in ZSoil® software. To simplify the probabilistic approach,...
-
Surface texture of pine wood beams after planing in industrial conditions
PublicationMeasuring the surface features of wooden components after planing is connected with the rising demands regarding to the quality of the painted window frames. In the paper the complex surface texture analysis especially identifying of surface damages using non-contact 3D measurement techniques for precise area measurement were presented.This enabled the study of irregular surface features with sufficient fidelity and resolution....
-
Static Load Test on Instrumented Pile – Field Data and Numerical Simulations
PublicationFor some time (since 8-10 years in Poland) a special static load tests on instrumented piles are carried out. Such studies are usually of a scientific nature and provide detailed quantitative data on the load transfer into the ground and characteristics of particular soil layers interaction with a pile shaft and pile base. Deep knowledge about the pile-subsoil interaction can be applied for a various design purposes, e.g. numerical...
-
Data recorded for the purpose of the 3D sound intensity visualization around the organ pipe (des sound)
Open Research DataThe set contains data recorded using the Cartesian robot and multichannel acoustic vector sensor (from Microflown) for the purpose of the 3D sound intensity visualization of radiated acoustic energy around the organ pipe.
-
Synergistic effects of a swirl generator and MXene/ water nanofluids used in a heat exchanger pipe of a negative CO2 emission gas power plant
Publicationfocus on optimizing heat exchangers contributes to improved temperature control mechanisms, ensuring the sustainable operation of innovative power plants working towards negative CO2 emissions. In the realm of oxy-combustion within Negative CO2 Emission Power Plants (nCO2PP), the temperature of combustion products surpasses 3000 (K). Addressing this challenge, the imperative arises to reduce these elevated temperatures to a manageable...
-
Identification of the Inertia of Masses Flowing Water through the Pipes in Water Power Plants
PublicationW artykule przedstawiono sposób identyfikacji stałej czasowej reprezentującej bezwładność mas przepływającej wody w systemie rurociągów, w elektrowni wodnej. Przedstawiono strukturę modelu układu regulacji prędkości kątowej wykorzystywanego w procesie identyfikacji oraz przeprowadzono badania skuteczności działania metody w środowisku Matlab-Simulink. Opisano najistotniejsze wnioski wynikające z przeprowadzonych badań symulacyjnych.
-
Removal of diphenols using pine biochar. Kinetics, equilibrium, thermodynamics, and mechanism of uptake
PublicationThermal pyrolysis synthesized activated biochar from the Pinus elliottii sawdust (PS) at 600° C. The obtained activated biochar (PB600) was used for the removal of three diphenols, catechol (CAT), resorcinol (RES), and hydroquinone (HYD), which are utilized mainly in different industries. The PB600 was characterized by several analytical techniques. The BET surface area of 1473 m2.g−1 and a total pore volume of 0.707 cm3 g−1 was...
-
Current Trends in Wick Structure Construction in Loop Heat Pipes Applications: A Review
PublicationThermal control systems have been introduced as an important part of electronic devices, enabling thermal management of their electronic components. Loop heat pipe (LHP) is a passive two-phase heat transfer device with significant potential for numerous applications, such as aerospace applications, high-power LEDs, and solar central receivers. Its advantages are high heat transfer capability, low thermal resistance, long-distance...
-
Rapid Microbial Community Changes During Initial Stages of Pine Litter Decomposition
Publication -
The sensitiveness of the speed of pile displacement to speed variations of hammer in beating down process
PublicationIn this paper there is presented dynamical system described speed of pile displacement during beating down process. Its response is determined by using Heaviside operator. There is introduced the convergence with regulator in partially ordered space. There is given an answer to the question, whetdisplacement is sensitive to hammer's speed variations.
-
Comparative model tests of SDP and CFA pile groups in non-cohesive soil
PublicationThe research topic relates to the subject of deep foundations supported on continuous flight auger (CFA) piles and screw displacement piles (SDP). The authors have decided to conduct model tests of foundations supported on the group of piles mentioned above and also the tests of the same piles working alone. The tests are ongoing in Geotechnical Laboratory of Gdańsk University of Technology. The description of test procedure, interpretation...
-
THE EFFECT OF DRYING INTENSITY ON THE COLOR CHANGES OF PINE WOOD (PINUS SYLVESTRIS L.)
PublicationThe effect of the selection of drying process parameters on the color change of Scots pine wood (Pinus Sylvestris L.) is presented. In this work the experimental studies have been performed. The research focused on the influence of drying intensity on the changes of color after drying process. Intensity of drying process was determined on the basis of the average drying gradient. To determine the color of wood before and after...
-
TUNNELLING AND UNDERGROUND SPACE TECHNOLOGY
Journals -
Experimental investigation on heat pipes supported by soy wax and lauric acid for electronics cooling
PublicationThis paper presents an experimental study of heat pipes for electronics cooling that were supported by energy storage materials (i.e. phase change materials - PCMs) coated at the adiabatic section. The PCMs utilized included two materials, namely lauric acid and soy wax, the latter being considered as a more cost-effective alternative. The study focused on three different powers: 20 W, 25 W, and 30 W. Both heating, cooling, and...
-
The Use of Wood Chips for Revitalization of Degraded Forest Soil on Young Scots Pine Plantation
Publication -
Effects of full displacement pile installation on the stress and deformation state of surrounding soil: review
PublicationSeveral field and model tests have been conducted to investigate the impact of pile installation on bearing capacity. However, little is known about how piles behave during installation, how they interact with the surrounding soil, and how this affects sandy soil properties. This review paper investigates the effect of pile driving on surrounding sandy soil as it compacts sandy soil near to the pile. For this purpose, various related...
-
Challenges in operating and testing loop heat pipes in 500–700 K temperature ranges
PublicationThe potential applications of loop heat pipes (LHPs) are the nuclear power space systems, fuel cell thermal management systems, waste heat recovery systems, medium temperature electronic systems, medium temperature military systems, among others. Such applications usually operate in temperature ranges between 500–700 K, hence it is necessary to develop an LHP system that will meet this requirement. Such a thermal management device...
-
3D Sound Intensity Measurement Around Organ Pipes Using Acoustic Vector Sensors
PublicationThe aim of the presented paper was to obtain and visualize sound intensity distribution of radiated acoustic energy around the organ pipes. The experimental setup consisted of the multichannel acoustic vector sensor and the specialized Cartesian robot. Measurements were performed in free field with spatial resolution of 0.1 [m]. Two organ pipes, i.e. wooden and metal were measured during the ex-periment. The organ pipes were activated...
-
Numerical estimation of the pile toe and shaft unit resistances during the installation process in sands
PublicationNumerical simulations of a pile jacking were carried out. A Coupled Eulerian–Lagrangian (CEL) formulation was used to treat with large deformation problems. An Abaqus, a commercial Finite Element Method software suit, was used as a computing environment. The Mohr–Coulomb constitutive model was applied and the Coulomb model of friction was used to describe pile-soil interaction. Calculations were made for three different pile diameters....
-
Effect of the Drying Method of Pine and Beech Wood on Fracture Toughness and Shear Yield Stress
PublicationThe modern wood converting processes consists of several stages and material drying belongs to the most influencing future performances of products. The procedure of drying wood is usually realized between subsequent sawing operations, affecting significantly cutting conditions and general properties of material. An alternative methodology for determination of mechanical properties (fracture toughness and shear yield stress) based...
-
Effect of pine impregnation and feed speed on sound level and cutting power in wood sawing
PublicationThe sound levels along with the cutting power registered during the sawing process of the impregnated and non-impregnated pine wood at two feed speeds are shown and compared in this paper. Statistically significant differences in the acoustic signals occurred at the lower feed rate. The differences became smaller with an increase in the feed speed. In contrast to the sound signal, the differences...
-
THE EFFECT OF LOG SORTING STRATEGY ON THE FORECASTED LUMBER VALUE AFTER SAWING PINE WOOD
PublicationThe optimal transformation path for the resource is determined by the quality of a log combined with its dimension. The commercial value of derived products is also closely connected with the size and extent of containing wood deficiencies. The results of studies with three diverse strategies for log sorting are presented in the paper. Resource assessment by a worker without extensive experience in sorting logs, the certified grading...
-
6.2, Engineering structures. [Chapter] 6.2.1, Assessment of the technical condition and repairs to cylindrical tank : 6.2.2, Assessment and repair of underground arterial pipelines : 6.2.4, Assessment and repair of steel chimneys
PublicationJerzy Ziółko opracował następujące fragmenty książki: w rozdziale 6.2. Engineering structures (Obiekty inżynierskie), pkt. 6.2.1 Assessment of the technical condition and repairs to cylindrical tank (Diagnostyka stanu technicznego i naprawy zbiorników walcowych), pkt. 6.2.2 Assessment and repair of underground arterial pipelines (Diagnostyka i naprawy podziemnych rurociągów magistralnych, pkt. 6.2.4 Assessment and repair of steel...
-
Experimental Investigation of the Thermal Performance of a Wickless Heat Pipe Operating with Different Fluids: Water, Ethanol, and SES36. Analysis of Influences of Instability Processes at Working Operation Parameters
PublicationIn this study, the influences of different parameters on performance of a wickless heat pipe have been presented. Experiments have been carried out for an input power range from 50 W to 300 W, constant cooling water mass flow rate of 0.01 kg/s, and constant temperature at the inlet to condenser of 10 C. Three working fluids have been tested: water, ethanol, and SES36 (1,1,1,3,3-Pentafluorobutane) with different filling ratios (0.32,...
-
Procedure for Determining Dimensional Allowances for PPE Using 3D Scanning Methods
Publication -
Analysis of surface roughness of chemically impregnated Scots pine processed using frame-sawing machine
PublicationThe objective of this work was to evaluate the effect of the impregnation process of pine wood (Pinus sylvestris L.) on roughness parameters of the surface processed on a frame sawing. The samples weredried and impregnated using a commercial procedure by a local company. The touch method withthe use of measuring stylus (pin) was employed to determine of surface roughness of the samplesconsidering parameters, namely, arithmetical...
-
Comparison of the fracture toughness of pine wood determined on the basis of orthogonal linear cutting and frame sawing
PublicationIn this paper, the values of the fracture toughness of Scots pine determined by cutting tests are presented. The cutting tests were carried out using the samples of Scotch pine (Pinus sylvestris L.) from Pomeranian Region, Poland. These experiments were carried out on two research stands: orthogonal linear cutting tests were conducted using the microtome instrument and the frame saw PRW-15M was used for sawing tests. The values...
-
Forecasting values of cutting power for the sawing process of impregnated pine wood on band sawing machine
PublicationW artykule przedstawiono prognozowane wartości mocy skrawania dla pilarki taśmowej (ST100R firmy STENNER), które są stosowane w polskich tartakach. Wartości mocy skrawania oszacowano dla drewna sosny zwyczajnej (Pinus sylvestris L.), które zostało poddane impregnacji. Dla porównania wyznaczono również wartości mocy skrawania dla drewna niezaimpregnowanego. Wartości te określono za pomocą innowacyjnej metody prognozowania sił skrawania,...
-
The dying medium temperature impact on the final moisture content of pine wood at constant drying time
PublicationThe results of final moisture content of pine wood (Pinus sylvestris L.) after drying process are presented. The wood in the experiments was taken from the northern part of Pomeranian region in Poland. The drying process was performed in the experimental chamber equipped with the micro-jet heat exchanger. The air at temperatures of 40°C, 60°C, 80°C, 100°C and 120°C with relative humidity about 60% and atmospheric pressure was the...
-
Fatigue Damage Development in 14MoV6-3 Steel for Power Plant Pipes Monitored by Digital Image Correlation
Publication -
Effect of high temperature exposure on the fatigue damage development of X10CrMoVNb9-1 steel for power plant pipes
Publication -
The Effect of Wood Provenance and Density on Cutting Forces While Sawing Scots Pine (Pinus sylvestris L.)
PublicationSeveral properties of wood including the cutting power requirements can be correlated to wood density. Therefore, according to the literature, the cutting power requirements (and/or cutting forces) could be computed as a function of the wood specific gravity. This research shows that such an approach, based solely on specific gravity, may be considered a rather rough and imperfect estimate of cutting power. Samples of Scots pine...
-
The differential impact of a density of Polish pine wood on cutting forces with its origin region taken into consideration
PublicationIn the article the dependence of cutting forces in a function the density of wood with regard to the wood origin are presented. Samples used in experiment were with Scotch pine (Pinus sylvestris L.) originating from four provenances in Poland (Figure 1). Wood density was measured by two methods: stereometric method (global density) and radiometric method (local density). Stereometric method consists in measurements the volume...
-
Effect of Thermal Shock During Legionella Bacteria Removal on the Corrosion Properties of Zinc-Coated Steel Pipes
PublicationThe purpose of this investigation was to conduct the failure analysis of a water-supply system made from zinc-coated steel. The observed corrosion process had an intense and complex character. The brownish deposits and perforations were present after 2-3 years of exploitation. The electrochemical study based on the Tafel polarization, corrosion potential monitoring, and electrochemical impedance spectroscopy together with microscopic...
-
Cutting model parameters from frame sawing of natural and impregnated Scots pine (Pinus sylvestris L.)
PublicationIn this paper, absolute and density normalized cutting model parameters of natural and impregnated Scots pine (Pinus sylvestris L.) are shown and a method for the calculation of their corresponding material properties in the principal material directions of wood is presented. The parameters were determined from measurements of cutting power on a sash gang saw, and are in detail the fracture toughness and the shear yield strength...
-
Analysis of the relationship between cutting forces and local structural properties of Scots pine wood aided by computed tomography
PublicationX-ray computed tomography (CT) is utilised in some sawmills today, primarily for enhancing value yield and for process automation, which includes log sorting and sawing optimisation. Nevertheless, there is a scarcity of recent research utilising CT to assess the local cutting process. As a preliminary study, this paper addresses this gap by using CT to investigate the connections between local cutting force and local wood properties...
-
Can Post-Activation Performance Enhancement (PAPE) Improve Resistance Training Volume during the Bench Press Exercise?
Publication -
Prediction of Pile Shaft Capacity in Tension Based on Some Direct CPT Methods—Vistula Marshland Test Site
PublicationThis paper presents different CPT methodologies for the prediction of the pile shaft resistance in tension on the example of three reference screw piles of the Jazowa test site in Poland. The shaft capacity was estimated based on the cone resistance, sleeve friction and CPT excess pore water pressure. Three piles with diameter 0.4 m and the length varied from 8 m to 14.6 m were subjected to static load tests in tension. Their...
-
Prediction of pile shaft capacity in tension based on some direct CPT methods – Vistula Marshland test site
PublicationThis paper presents different CPT methodologies for the prediction of the pile shaft resistance in tension on the example of three reference screw piles of the Jazowa test site in Poland. The shaft capacity was estimated based on the cone resistance, sleeve friction and CPT excess pore water pressure. Three piles with a diameter of 0.4 m and the length...
-
The effect of the annual growth and the late wood share upon density of the Polish pine wood as a function of its origin
PublicationW artykule przedstawiono zróżnicowanie gęstości polskiego drewna sosnowego (Pinus sylvestris L.) w zależności od udziału drewna późnego w przyroście rocznym z uwzględnieniem krainy pochodzenia drewna. Wspomniane zróżnicowanie jest w istotne statystycznie w skali globalnej oraz dla większości miejsc pochodzenia. Pomiar gęstości wykonano przy użyciu metody stereometrycznej. Metoda ta polegała na określeniu objętości pryzmy poprzez...
-
Mathematical model of the energy consumption calculation during the pine sawn wood (Pinus sylvestris L.) drying process
PublicationThe article presents the modification of the existing mathematical model to calculate energy consumption during conventional drying process. Apart from energy consumption the model permits to estimate the time of high-temperature drying process. The drying medium is air and superheated steam mixture. The obtained calculation results were compared with conducted experimental tests of drying square-edged sawn sapwood timber (Pinus...
-
Some Aspects of Shear Behavior of Soft Soil–Concrete Interfaces and Its Consequences in Pile Shaft Friction Modeling
PublicationThis paper examines the stiffness degradation and interface failure load on soft soil–concrete interface. The friction behavior and its variability is investigated. The direct shear tests under constant normal load were used to establish parameters to hyperbolic interface model which provided a good approximation of the data from instrumented piles. Four instrumented piles were used to obtain reference soil–concrete interface behavior....
-
SHEAR YIELD STRESSES AND FRACTURE TOUGHNESS OF SCOTS PINE (PINUS SYLVESTRIS L.) ACCORDING TO THE RAW MATERIAL PROVENANCE
PublicationIn this paper values of the fracture toughness and of shear yield stress in the shear zone of Scots pine are presented. Tests of cutting were carried on samples of Scotch pine (Pinus sylvestris L.) wood of five provenances from Poland. These experimentally cutting tests were carried on the sash gang saw PRW-15M and the values of cutting power were obtained. The values of fracture toughness and shear yield stress based on Atkins’s...
-
The low temperature waste heat recovery in drying process of pine wood using micro-jet heat exchanger
PublicationThe article presents the influence of the drying medium temperature changes for the relative and absolute moisture content values during pine wood drying. The drying process was conducted at constant atmospheric pressure and with different drying medium (air) temperature levels, respectively: 40oC, 60oC, 80oC, 100oC, and 120oC. In order to develop a method that would enable low temperature drying of solid materials the experiments...