Filters
total: 2132
-
Catalog
displaying 1000 best results Help
Search results for: DISINTEGRATION-BOILING
-
Engineering method of tire rolling resistance evaluation
PublicationTire rolling resistance is one of the most difficult tire parameters to measure. The reason is that for modern tires the force of rolling resistance corresponds to 0.5–1% of tire load, thus measurements of very small forces must be performed in a heavily loaded system. This constitutes great problems, especially in road conditions. Laboratory measurements are easier to perform, as the environment may be better controlled, but roadwheel...
-
Structural optimization of microjet array cooling system
PublicationThe single phase heat transfer from an upward facing, horizontal copper surface to arrays of impinging water jets was experimentally investigated. Experimental configuration allows for a free-surface unconfined jets flow. Square nozzles 50 × 100 μm arranged in four different geometries were used. Additionally, for the set of two jets array geometry was varied by adjusting the nozzle to nozzle distance. The area averaged heat transfer...
-
Several notes on technical modernization of a historical building
PublicationThis paper describes methods and means used during the renovation process of several elements of a building – the assembly hall, inner courtyards and attics of the main building at Gdansk University of Technology, both in design and construction domains. A tissue of a historic building required special approach to these tasks, with special emphasis on good recognition of problems, careful planning and consistent implementing of...
-
Fouling in direct contact membrane distillation process
Publication -
Tire rolling resistance measurements on the road and in the laboratory
PublicationW pracy przedstawiono stanowisko bębnowe do badania oporu toczenia opon samochdowych w warunkach laboratoryjnych. Zaprezentowano także przyczepę dynamometryczną do badania oporu toczenia opon samochodowych w warunkach drogowych. Stanowisko bębnowe i przyczepa zosały zbudowane w Katedrze Pojazdów i Maszyn Roboczych Politechniki Gdańskiej. Omówiono wpływ wzdłużnego pochylenia drogi i naporu powietrza na badane koło na dokładność...
-
Sailing (Jedrenje), akryl na płótnie 90x60cm
PublicationKatalog Biennale i dwóch wystaw zbiorowych poplenerowych: City Museum Trogir 09-21-09.2008, Palaca Milesi Split 08.-23.10.2008.
-
Some aspects surface cooling by impinging jet
PublicationW pracy przedstawiono wyniki badań wymiany ciepła, uskoku hydraulicznego i stabilności podczas napływu strugi na powierzchnię ciała stałego.
-
Political Institution Building in Post-Communist Romania
Publication -
The lubricant-coating interaction in rolling and sliding contacts
Publication -
Emergency condition of the ceramic facade of a residential building
PublicationThe paper presents a description of the technical condition of the ceramic cladding of a residential building, the technical condition of which deteriorated significantly after only a few years of operation. The analysis of the influence of the applied design and working solutions on the façade failure frequency was analyzed. The article presents a conceptual solution to bring the building to the proper technical condition in terms...
-
Cast iron in the 19th-century building equipment
PublicationCast iron is a material, characteristics of which enable to receive extremely artistic elements. It maintains good strength properties at the same time. That combination of these seemingly contrary traits makes it a commodity that was widely used in the 19th century industry and architecture. These usages were not only as decorative elements, technical and structural ones. The production of new household utilities started, which...
-
Cooperative editing approach for building Wordnet database
PublicationArtykuł przedstawia podejście do kooperacyjnej pracy nad baza danych systemu Wordnet. Opisana została architektura systemu oraz wizualizacja sieci powiązań konceptualnych z użyciem komponentu touchgraph.
-
Cooling of electronic equipment by means of jets and microjets
PublicationW pracy przedstawiono rozwiązanie sprzężonej wymiany ciepła od uderzającej strugi cieczy oraz przewodzenia ciepła w łytce. Uzyskano proste zależności opisujące rozkład temperatur na płytce. Umożliwia to przeprowadzenie analizy wpływu różnych parametró na wymianę ciepła podczas chłodzenia urządzeń elektronicznych generujących ciepło.
-
Building Sustainable Cities. Challenges for professional education
PublicationW artykule zawarto rozważania na temat problemu dostosowania profilu i charakteru edukacji planistycznej i urbanistycznej do potrzeb zmianiającego się świata. W szczególności okreslone zostały przyczyny koniecznych zmian wtym zakresie oraz kierunki działania.
-
Building Employer Credibility in Corporate Intranet Portals.
PublicationPublikacja omawia rolę portalu intranetowego w kształtowaniu relacji pracodawca-pracownicy w przedsiębiorstwie. W szczególności omówiono środki budowy wizerunku i wiarygodności pracodawcy w elektronicznych kanałach komunikacji. Na podstawie wyników badań ankietowych wśród polskich przedsiębiorstw wskazano typowe profile użytkowania intranetu oraz czynniki ergonomiczne i organizacyjne budujące satysfakcję użytkowników z portali...
-
New generation cooling systems for car engines
PublicationNormy czystości spalin silników samochodowych wymusiły rozwój elektronicznego sterowania pracą silników samochodowych. Do niedawna układy chłodzenia były bardzo tradycyjnymi - niesterowanymi programowo. W artykule przedstawiono możliwości wprowadzenia zaawansowanego sterowania mikroprocesorowego do układów chłodzenia silników spalinowych. Rozważania zilustrowano badaniami z literatury i własnymi pomiarami autora.
-
Updating a hospital building. A task for innovation design
PublicationRefurbishment of a hospital, especially located in a historical building, is a task that goes far beyond a standard framework of architectural practice. A concept of modularity in the architecture of the late nineteenth and early twentieth century was only just to happen, building system installations and technical equipment appeared as the simplest solutions. Inscribing complex functional solutions into such a space is an interesting...
-
Analysis of Asymmetrical Rolling Process of Multilayer Plates
PublicationW niniejszej pracy przedstawiono wyniki badań numerycznych asymetrycznego procesu walcowania blach wielowarstwowych M1E-Al99,8-AlMg5. Modelowanie numeryczne procesu walcowania blach wielowarstwowych przeprowadzono w programie Forge 2D, którego obliczenia bazują na metodzie elementów skończonych. Przedstawione w pracy wyniki umożliwiły przeprowadzenie analizy procesu walcowania blach wielowarstwowych.
-
Safety-based approach in multifunctional building design
PublicationABSTRACT: The modern trend in design of the public buildings is to create multifunctional environments in one building, hosting a variety of functions. Multifunctional buildings entertain large number of visitors. The complexity and vulnerability of this type of public space are the main reasons to use within their design process the performance based approach including the recognition of hazards. Safety and reliability approach...
-
Hertzian Crack Propagation in Ceramic Rolling Elements
PublicationThe properties of ceramics are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such crack are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations are based on a three dimensional model for the ring crack propagation. The stress intensity factors along crack...
-
Performance of a hybrid microjet – microchannel cooling module
PublicationThe paper presents the experimental investigation of a microjet- microchannel cooling module. In which microjets of water are impinging into the microchannels and forming a liquid film on the impingement surface. Applied technology takes benefits from two very attractive heat removal techniques. When lminar jets are impinging on the surface have a very high kinetic energy at the stagnation point, also in microchannels boundary...
-
Road texture influence on tire rolling resistance
PublicationTire rolling resistance is one of the most important resistive forces acting on road vehicles. It depends on tire and surface characteristics as well as vehicle operating parameters. This paper deals with the influence of road surface texture on rolling resistance of passenger car tires. Results of road measurements performed on variety of road surfaces are presented.
-
Development trends of automotive engine cooling systems
PublicationDzięki daleko idącym modyfikacjom układów zasilania i zapłonu silników samochodowych oraz udoskonaleniom układów oczyszczania spalin uzyskano znaczne zmniejszenie emisji związków toksycznych. Układy chłodzenia z pompą cieczy napędzaną mechanicznie stają się archaiczne nie pozwalając na swobodne sterowanie obiegiem cieczy. Również różna wartość temperatury potrzebnej do schładzania różnych procesów wymaga sterowanych zaworów trójdrożnych...
-
Fuzzy Methods and Models for a Team-Building Process
PublicationThis chapter contains an introduction to fuzzy-logic model-based approaches for a team-building process. Such appraches allow extending typical recruiting practice and selection processes to enable a wider and more precise assessment of a new team and/or existing team members, taking into account both their hard and soft skills. Moreover, as effectiveness of teams depends on the interpersonal skills and emotional intelligence...
-
Reactive Energy Billing in Operator Tariffs in Poland
PublicationThe paper describes the current method of reactive energy billing in the tariffs of distribution grid operators in Poland. The current solutions are subject to critical assessment. Issues related to the motivation effect of the current solutions on consumers are analysed. Problems that occur in relation with connecting distributed generators to the distribution grid and challenges related to prosumer billing are indicated.
-
Road texture influence on tyre rolling resistance
PublicationTyre performance, one of the critical factors for vehicle users, is strongly related to theroad surface characteristics, most notably to the pavement texture. Phenomena that occur at the tyre/road interface affect tyre friction (skid resistance), rolling resistance, tyre wear and tyre/road noise. This article deals with relationship between surface texture and rolling resistance of light and heavy vehicle tyres. Mean profile depth...
-
Multi-objective weather routing of sailing vessels
PublicationThe paper presents a multi-objective deterministic method of weather routing for sailing vessels. Depending on a particular purpose of sailboat weather routing, the presented method makes it possible to customize the criteria and constraints so as to fit a particular user’s needs. Apart from a typical shortest time criterion, safety and comfort can also be taken into account. Additionally, the method supports dynamic weather data:...
-
METHOD OF ROUTING SHIPS SAILING IN DEDICATED ENVIRONMENT
PublicationThe method for determining the suboptimal route of sailing vessels operating in a restricted area of the sea are proposed in the paper. The dynamics of the environment including weather conditions and speed characteristics of ships sailing are considered. As optimiza-tion criterion, measure sailing time T, and the number of maneuvers performed ω, are taken into account. An heuristic algorithm, and the appropriate application routing...
-
Influence of Property Division on the Technical Condition of a Building
PublicationIn this article, the correlation between a technical condition of a building and property division is analyzed and assessed. In the course of the usage of a building, the process of its degradation and the increase in the demands of property occupants can be observed. There is a direct connection between the difficult technical condition of a building and the fragmentation of the ownership structure. Although not considered in...
-
Building Knowledge for the Purpose of Lip Speech Identification
PublicationConsecutive stages of building knowledge for automatic lip speech identification are shown in this study. The main objective is to prepare audio-visual material for phonetic analysis and transcription. First, approximately 260 sentences of natural English were prepared taking into account the frequencies of occurrence of all English phonemes. Five native speakers from different countries read the selected sentences in front of...
-
Modelling of joining route segments of differential curvature
PublicationThe paper presents a new general method of modelling route segments curvature using differential equations. The method enables joining of route segments of different curvature. Transitional curves of linear and nonlinear curvatures have been identified in the case of joining two circular arcs by S-shaped and C-oval transitions. The obtained S-shaped curves have been compared to the cubic C-Bezier curves and to the Pythagorean hodograph...
-
Modeling of the internal combustion engine cooling system
PublicationThe article concerns computer modelling of processes in cooling systems of internal combustion engines. Modelling objectives and existing commercial programs are presented. It also describes Author’s own method of binding graphs used to describe phenomena in the cooling system of a spark ignition engine. The own model has been verified by tests on the engine dynamometer. An example of using a commercial program for experimental...
-
Chalcogen bonding interactions in a series of aromatic selenocyanates
PublicationSelenium atoms in aromatic selenocyanates are characterized by the occurrence of two σ-holes, a stronger one in the prolongation of the NC–Se bond and a weaker one in the prolongation of the Ar–Se bond. The crystal structures of several bis(selenocyanato) derivatives, prepared by a method originally developed for ortho bis-substituted derivatives, illustrate very well this difference, with a short NC–Se⋯NC ChB interaction organizing...
-
Digitalization of Building Site Management in the Construction Industry
PublicationWith Industry 4.0, a digital transformation has started in the construction industry. However, 4.0 technologies have difficulties in the integration of digital systems due to the diversity and complexity of the processes in the construction industry. Multidisciplinary work in architectural projects and the need for high productivity require digital renovation planning in the construction industry. The application of the technologies...
-
Emergency condition of the ceramic facade of a residential building
PublicationThe paper presents a description of the technical condition of the ceramic cladding of a residential building, the technical condition of which deteriorated significantly after only a few years of operation. The analysis of the influence of the applied design and working solutions on the façade failure frequency was analyzed. The article presents a conceptual solution to bring the building to the proper technical condition in terms...
-
Beijing Hangkong Hangtian Daxue Xuebao/Journal of Beijing University of Aeronautics and Astronautics
Journals -
Evaluating Asphalt Mix Ingredients by Moisture Susceptibility: The Development of a New Modified Boiling Test Procedure Based on Digital Imaging
Publication -
Pool boiling heat transfer of water-Al2O3 and water-Cu nanofluids on horizontal stainless steel smooth and rough tubes
PublicationPrzedstawiono wyniki badań eksperymentalnych przejmowania ciepła przy wrzeniu nanocieczy woda-Al2O3 i woda-Cu na poziomych rurkach ze stali nierdzewnej. Ustalono, że niezależnie od badanej koncentracji nanocząstek (0.01%, 0.1% oraz 1%) współczynnik przejmowania ciepła dla nanocieczy był wyższy niż dla wody i rósł ze wzrostem koncentracji. Ponadto współczynnik przejmowania ciepła dla nanocieczy wzrastał ze wzrostem ciśnienia.
-
Heat transfer and pressure drop during flow boiling of pure efrigerants and refrigerant/oil mixtures in tube with porous coating
PublicationW pracy przedstawiono wpływ powłoki porowatej na średni współczynnik przejmowania ciepła oraz opory przepływu podczas wrzenia wybranych czynników chłodniczych wewnątrz poziomych rurek. Badania przeprowadzono dla techniczne czystych czynników chłodniczychR22, R134a i R407C oraz ich mieszanin z olejem poliestrowym 1% i 5% wrzących w rurkach wykonanych ze stali nierdzewnej, o wewnętrznej powierzchni gładkiej oraz z metaliczną powłoką...
-
Decreasing CO2 Emissions By Reducing Tire Rolling Resistance
PublicationThe first motor vehicle was built by Nicolas Cugnot almost 250 years ago and since then there has been a continuous process of motor vehicles’ improvements, as well as development of new road pavements. The fuel crisis of the 70s of the 20th century made it clear to vehicle builders that measures should be taken to reduce vehicle fuel consumption and it contributed to an increased interest in electric vehicles. Although significant...
-
The automation of test stand for engine cooling system testing
PublicationW rozdziale przedstawiono budowę stanowiska do badań układu chłodzenia silnika samochodowego typu M111920. Układ był wyposażony w obwód podgrzewania paliwa gazowego i układ akumulacji ciepła. Stanowisko wyposażono w liczne termopary do pomiaru temperatur płynów i części metalowych silnika. Ważnym opracowanym zagadnieniem było rejestrowanie wielu pomiarów w czasie rzeczywistym, do czego użyto sieci transmisji danych CAN.
-
Thermal simulation of building performance with different loadbearing materials
Publication -
Building the Fuzzy Control System Based on the Pilot Knowledge
Publication -
Building a heterogeneous network of digital libraries on the Semantic Web
PublicationBiblioteki dążą do skupiania się w grupy, które poza lokalnym wyszukiwaniem pozwalają na wyszukiwanie zasobów w pozostałych bibliotekach cyfrowych. Jednakże różne typy użytkowników zapoczątkowały różne rodzaje bibliotek. W niniejszym artykule przedstawiamy jak obecnie odbywa się komunikacja między bibliotekami cyfrowymi. Prezentujemy również w jaki sposób technologie Semantic Web mogą pomóc w rozwiązaniu problemów heterogenicznych...
-
Analysis of electrical energy consumption on the example of a selected building
Publication -
Manufacturing of resistant joints by rolling for light tubular structures
PublicationKoncepcja łączenia aluminiowych elementów rurowych z zastosowaniem nagniatania plastycznego jest alternatywą do istniejących metod łączenia przez spawanie i skręcanie. W artykule prezentowane są oryginalne wyniki badań wpływu parametrów nagniatania wewnętrznego i zewnętrznego oraz różnych postaci powierzchni łączonych na wytrzymałość złącza (aluminium-aluminium) pod wpływem rozciągających sił osiowych.Badania przeprowadzono na...
-
Parametric method of preliminary prediction of the ship building costs
PublicationPrzedstawiono założenia koncepcyjne i teoretyczne metody, opracowano wzory aproksymacyjne służące odpowiednio do wyznaczania jednostkowych kosztów budowy: kadłuba, wyposażenia okrętowego oraz siłowni z układem napędowym. Utylitarny charakter metody zilustrowano przykadami prognoz kosztów budowy czterech różnych typów statków zaprojektowanych w ramach projektu EUREKA BALTECOLOGICALSHIP E!3065.
-
The surface contact characteristics after sliding and rolling burnishing.
PublicationW pracy przedstawiono zastosowanie nowej metody SCGC i odpowiedniego programu komputerowego JKC do oceny pomierzonej mikrostereometrii powierzchni części maszyn, głównie na potrzeby kontroli jakości. Na przykładzie powierzchni nagniatanych wykazano cechy nowej metody: wizualizację ułatwiającą wyobrażenie pomierzonej sfery chropowatości, położenie w niej najważniejszych parametrów oceny (rozkład geometrycznej powierzchni kontaktu,...
-
The Rolling Contact Fatigue of PVD Coated Spur Gears
Publication -
Hybrid use of the building as a method supporting epidemic safety
PublicationThe COVID-19 pandemic has resulted in changing organisational and technical requirements in the operation of treatment facilities. This paper summarises the available knowledge on the principles of hybrid design of the architecture of treatment units to ensure that different levels of sanitary and hygienic safeguards can be implemented. The basis of this narrative overview is an analysis of the existing Polish legislation on required...