Filters
total: 3812
-
Catalog
displaying 1000 best results Help
Search results for: LASER REMELTING
-
Surface treatment of C80U steel by long CO2 laser pulses
PublicationThe paper presents the results of laser-melted C80U steel. The processed steel was placed between two permanent magnets and laser beam whose scanning velocity was 10 mm/s. CO2 laser beam was working in pulse mode. Pulses were generated at 100% of the average preset power of 700W, with 45 ms irradiation, zero interval between pulses and beginning of pulse repetition upon the achievement of the average laser power. During the operation,...
-
Laser surface treatment of aluminium-silicon alloy at cryogenic conditions
PublicationW artykule przedstawiono wpływ laserowego, powierzchniowego przetapiania w warunkach kriogenicznych na mikrostrukturę, mikrotwardość, zużycie na skutek tarcia oraz korozję stopu aluminium AlSi13Mg1CuNi. Stwierdzono zwiększenie mikrotwardości, odporności na ścieranie i korozję odlewniczego stopu AlSi13Mg1CuNi stosowanego w produkcji tłoków silników spalinowych.
-
Characterization of the Co-base layers obtained by laser cladding technique.
PublicationBadano zawory wydechowe napawane dwoma stopami kobaltu, w tym mikrostrukturę strefy wierzchniej i strefy w pobliżu podłoża. Badano także rozkład pierwiastków w warstwie napawanej. Stwierdzono podobny skład chemiczny warstw i proszków.
-
Characterization of the Co-base layers obtained by laser cladding technique.
PublicationBadano zawory wylotowe pokrywane stopami kobaltu: mikrostrukturę warstw w strefie wierzchniej i przy granicy napoina - metal. Badano rozkład pierwiastków w warstwach. Zarówno mikrostruktura, jak i skład chemiczny warstw były podobne w przypadku dwóch stosowanych stopów kobaltu.
-
Daniel Chuchała dr hab. inż.
People -
Pressure field in a plane layer
PublicationPraca prezentuje wyniki badań teoretycznych i numerycznych zagadnienia przejścia fal płaskich przez warstwę. Omówiono zagadnienie tworzenia i rozchodzenia się fal w poszczególnych warstwach. Zaproponowano model matematyczny opisujący zmiany ciśnienia wewnątrz warstwy. Analizowano ciśnienie wewnątrz warstwy, fale bieżące i odbite wewnątrz warstwy oraz w ośrodku otaczającym. Przedstawiono wyniki badań numerycznych.
-
Revised structure of the repeating unit of the O-specific polysaccharide from Azospirillum lipoferum strain SpBr17
PublicationO-polisacharyd otrzymany poprzez delikatną kwasową hydrolizę lipopolisacharydu wyizolowanego z Azospirillum lipoferum SpBr17 był badany metodami spektroskopii NMR jak również metodą analizy metylacyjnej połączonej z elektroforezą SDS-PAGE. Stwierdzono, że nie jest on liniowym homopolimerem złożonym wyłącznie z (1->3) [alfa]-glikozydowo połączonych cząsteczek L-ramnopiranozy (jak proponowano wcześniej) lecz sekwencją kolejnych bloków...
-
The influence of different glycerine purities on chemical recycling process of polyurethane waste and resulting semi‐products
PublicationChemical recycling is the most favourable recycling method due to the possibility of polyol recovery. This work is dedicatedto the utilisation of crude glycerine and polyurethane waste. It aims at determining the impact of the use of glycerine fromthe production of biodiesel with various degrees of purity as a cleavage agent on the decomposition process of polyurethanefoam. The influence of glycerine purit y on the chemical structure...
-
Preparation of Hydrogen Electrodes of Solid Oxide Cells by Infiltration: Effects of the Preparation Procedure on the Resulting Microstructure
PublicationIn this work, the infiltration technique was used to produce hydrogen electrodes for solid oxide cells. Different infiltration methodologies were tested in order to try to shorten the infiltration cycle time. The porous scaffolds used for infiltration were based on highly porous yttria-stabilized zirconia (YSZ) obtained by etching the reduced nickel from the Ni-YSZ cermet in HNO3 acid. The support had a complex structure which...
-
Deformation and Surface Color Changes of Beech and Oak Wood Lamellas Resulting from the Drying Process
PublicationThe drying process was examined relative to parameters’ influence on the deformation and surface layer color changes of beech wood (Fagus sylvatica L.) and oak wood (Quercus robur L.). The goal was to analyze the impact of drying process conditions, wood and growth rings types, and load on the deformation and surface color changes of drying thin wooden elements. A further aim was to reduce the time of the lamella drying and minimize...
-
LASE Journal of Sport Science
Journals -
Improvements to the two-phase sandwich method for calculating the melting points of pure metals
PublicationThe thermophysical properties of metal alloys are often investigated via molecular dynamics (MD) simulations.An exact and reliable estimation of the thermophysical parameters from the MD data requires a properly and carefullyelaborated methodology. In this paper, an improved two-phase sandwich method for the determination of the metal meltingtemperature is proposed, based on the solid-liquid equilibrium theory. The new method was...
-
Structural studies and melting of bismuth nanocrystals in reduced bismuthgermanate and bismuth silicate glasses.
PublicationOtrzymano nanostruktury krystalicznego bizmutu w matrycy XO2 (X=Si,Ge) oraz warstwę nanostruktur krystalicznego bizmutu na powierzchni redukowanych w atmosferze wodoru szkieł Bi0.33Ge0.67O1.84 i Bi0.57Si0.43O1.72. Kompozyt Bi-szkło badano metodą DSC, XRD oraz AFM. Zaobserwowano zmniejszenie temperatury topnienia nanokrystalicznego bizmutu znajdującego się w matrycy szkła z 544 K do 387 K oraz do 502 K w przypadku powierzchniowej...
-
ELECTROCHEMOTHERAPY COMBINED WITH STANDARD AND CO2 LASER SURGERIES IN CANINE ORAL MELANOMA
Publication -
Determination of grain shape of laser-irradiated FePdCu thin alloy films
Publication -
Porous Selective Laser Melted Ti and Ti6Al4V Materials for Medical Applications
Publication -
Cavitation wearing of the SUPERSTON alloy after laser treatment at cryogenic conditions
PublicationThe purpose of this paper is to demonstrate the method of laser remelting at cryogenic conditions of the SUPERSTON alloy and its influence on microstructure and cavitation wearing. The cavitation test was performed using the rotating disc facility in IPM PAN Gdansk. During the cavitation test, the mass loss of the material with different parameters of laser remelting was determined. Surface and cross-section microstructure of the...
-
Study of structures and properties of the laser cladding exhaust valve after service
PublicationPrzylgnie zaworów wydechowych silnie obciążonego silnika okrętowego zostały pokryte warstwą wykonana ze stopu kobaltu za pomocą techniki napawania laserowego. Tak przygotowane zawory były eksploatowane przez 3000 godzin w silniku Daru Młodzieży. Po tym czasie zostały zdemontowane i poddane szczegółowej analizie. Warunki pracy spowodowały powstanie na powierzchni przylgni warstwy tlenków o różnej grubości, wykazującej skłonność...
-
Surface layers analysis of bronze artifacts by means of laser spectroscopy techniques
Publication.
-
Operation of a free-electron laser from the extreme ultraviolet to the water window
Publication -
European X-Ray Free Electron Laser (EXFEL): local implications
Publication -
Comparison of Vacuum Sintered and Selective Laser Melted Steel AISI 316L
Publication -
Laser Surface Alloying of Aluminium Alloys with Cu/Fe Metallic Powders
Publication -
The influence of laser alloying on the structure and mechanical properties of AlMg5Si2Mn surface layers
Publication -
Laser Surface Treatment of Sintered Stainless Steels for Wear Resistance Enhancement
Publication -
Acousto-optic interaction with the use of cylindrical ultrasonic waves in the laser cavity
Publication -
Surface structure and propoerties of Ti6Al4V alloy laser melted at cryogenic conditions
PublicationPrzedstwiono wyniki badań mikroskopowych i mikrotwardości warstwy wierzchniej poddanej przetapianiu laserem w ciekłym aocie przy mocy laserz 3000-6000 W. Stwierdzono wzrost twardości i utworzenie zróżnicowanej warstwy wierzchniej.
-
Metal Oxides and Low Temperature SWCNT Synthesis via Laser Evaporation
Publication -
THE POSSIBILITY OF USE OF LASER-MODIFIED Ti6Al4V ALLOY IN FRICTION PAIRS IN ENDOPROSTHESES
PublicationThe purpose of this paper is to show results of laser treatment at cryogenic conditions of the Ti6Al4V alloy used for orthopedic applications. That modification process ought to bring beneficial changes of microstructure and residual stresses in the surface layer. The paper presents the abrasive wear of the base and laser remelted material in association with ceramics Al2O3. Despite the surface cracking after laser treatment the...
-
Laser patterned platform with PEDOT–graphene composite film for NO2 sensing
PublicationThis work presents a simple and fully electrochemical route used for fabricating of a NO2 gas sensor made of reduced-graphene-oxide-poly(3,4-ethylenedioxythiophene) composite film. The sensing platform was fabricated from alumina substrate and equipped with gold interdigitated electrodes and built-in heater.The temperature distribution on the surface of interdigitated electrodes was investigated by a thermalimaging camera and compared...
-
Airborne and mobile laser scanning in measurements of sea cliffs on the southern Baltic
PublicationMeasurements of sea cliffs performed using periodic surveying based on laser scanning is currently one of the fastest and most accurate solutions. Supported with the technology of satellite measurements using GNSS (Global Navigation Satellite System) positioning and photographic measurements with the use of aerial vehicle, they enable an effective monitoring of the sea cliffs affected by the erosion. In case of the coast of southern...
-
Micropatterning of BiVO 4 Thin Films Using Laser-Induced Crystallization
PublicationRelatively high temperatures even up to 500 °C are required to obtain bismuth vanadate (BiVO4) films with the scheelite monoclinic (s-m) structure that shows the highest photocatalytic activity. This requirement limits the possible choice of substrates. Moreover, high quality thin layers of crystalline BiVO4 cannot be prepared with current methods. In this study a light-induced crystallization approach is presented, which is a...
-
Coastal Cliffs Monitoring and Prediction of Displacements Using Terrestial Laser Scanning
PublicationCoastal cliffs are very sensitive to degradation caused by erosion and abrasion. Thus, it is very important to monitor susceptibility of the cliffs in terms of slope angles and ground fall resulting from vertical morphology of the cliffs. The results could be used for example to establish the boundaries of the safe investments zone or retreat infrastructure buildings in case of real threat such as degradation of the objects of...
-
Analysis of the applicability of laser scanning to making an inventory of swimming pool facilities
Publication3D scanning can be used in many branches of economy, e.g. reverse and prototype engineering, industrial design, quality control, pros-thetics, orthodontics, archiving of historic objects and archeological findings, examination of a scene of crime, making films and comput-er games. The technology of terrestrial laser scanning has a bright fu-ture as we are living in the time of blooming measurement tech-niques, which can provide...
-
A new approach of coastal cliff monitoring using Mobile Laser Scanning
PublicationThe article proposes a new approach of coastal cliff monitoring which bases on a new comprehensive monitoring system, being a combination of mobile scanning from the sea with the geotechnical stability analysis. Mobile laser scanning is an innovative solution for 3D data collection which allows the monitored object geometry to be precisely measured, thus providing opportunities for series of analyses contributing to the development...
-
Effects of the preheating laser treatment on microstructure and corrosion resistance of Ti6Al4V bioalloy
PublicationThe laser remelting of the Ti6Al4V alloy was made on specimens pre-heated at elevated temperatures. The laser treatment effected in change of microstructures of surface layers and an appearance of blisters and numerous cracks. The corrosion tests demonstrated the decrease in corrosion resistance for each preheating temperature. The observed effects were attributed to negative influence of excessive compressive stresses with no...
-
Effects of laser pulse duration in two-photon vision threshold measurements
PublicationPulsed near-infrared (NIR) light sources can be successfully applied for both imaging and functional testing of the human eye, as published recently1. These two groups of applications have different requirements. For imaging applications, the most preferable is invisible scanning beam while efficiently visible stimulating beam is preferable for functional testing applications. The functional testing of human eye using NIR laser...
-
The effect of laser on metal surfaces for multidisciplinary usage in material and thermal engineering
PublicationThe subject of heat transfer and cooling systems is still a matter of contention in many different fields of science and industry. Infrigidation is much more difficult than warming, and so, much more needed in more and more different devices, starting from massive industrial machinery and air conditioning in commercial buildings, up to micro and nano-surgery tools. In fact, the size of many cooling systems is still a problem. It...
-
Using terrestrial laser scanning in inventorying of a hybrid constructed wetland system
PublicationThe goal of this paper was to evaluate the possibility of using terrestrial laser scanning (TLS) for inventorying of a hybrid constructed wetland (CW) wastewater treatment plant. The object under study was a turtle-shaped system built in 2015 in Eastern Poland. Its main purpose is the treatment of wastewater from theMuseumand Education Centre of Polesie National Park. The study showed that the CW system had been built in compliance...
-
Optical and photoelectrochemical characterization of pulsed laser deposited Bi4V2O11, BICUVOX, and BIZNVOX
PublicationThin layers of three compounds from the BIMEVOX family (Bi4V2O11, Bi2V0.9Cu0.1O5.35, and Bi2V0.9Zn0.1O5.35) were prepared via pulsed laser deposition technique on quartz, silicon, and platinum foil and tested as photoanodes for water photooxidation. The film formation, as well as the crystallization upon heating, was characterized using X-ray diffraction and Raman spectroscopy. The optical properties were investigated using spectroscopic...
-
Laser Dissimilar Welding of AISI 430F and AISI 304 Stainless Steels
PublicationA dissimilar autogenous laser welded joint of AISI 430F (X12CrMoS17) martensitic stainless steel and AISI 304 (X5CrNi18-10) austenitic stainless steel was manufactured. The welded joint was examined by non-destructive visual testing and destructive testing by macro- and microscopic examination and hardness measurements. With reference to the ISO 13919-1 standard the welded joint was characterized by C level, due to the gas pores...
-
Cavitation erosion of heterogeneous thin coatings produced by means of laser cladding
PublicationPrzedstawiono badania odporności kawitacyjnej cienkich heterogenicznych warstw nakładanych metodami laserowymi na stal 45. Wykazano dobrą przyczepność i wysoką odporność kawitacyjną wykonanych powłok.
-
Effect of laser treatment on the wear and corrosion resistance of aluminiumalloy used for pistons
PublicationPrzedstawiono wpływ powierzchniowego laserowego przetapiania w warunkach kriogenicznych na skład chemiczny, mikrostrukturę, mikrotwardość oraz zużycie ścierne i odporność korozyjną stopu AlSi13Mg1CuNi stosowanego na tłoki silników spalinowych. Uzyskano zwiększenie odporności na ścieranie i korozję stopu AlSi13Mg1CuNi.
-
Improved top hat and ushaped resistors for huigh precision laser trimming.
PublicationPrzedstawiono nowe podejście do poprawy charakterystyk strojenia rezystorów warstwowych typu ''kapelusza'' i typu ''U'' z cięciem prostym pośrodku struktury polegająca na wprowadzeniu zaworki przewodzącej w górnej części rezystora. Umożliwia to eliminację lokalnych przegrzewów oraz zwiększenia dokładności strojenia i wzrostu stabilności.
-
Morphology studies of the cobalt base clad layers produced by laser technology.
PublicationPrzedmiotem badań były utwardzające warstwy wykonane na przylgni zaworów wydechowych silnika spalinowego. Materiał podłoża to stal H10S2M. Zastosowano technologię napawania laserowego proszków na bazie kobaltu. Proszki różniły się jedynie zawartością wolframu i zawierały odpowiednio 4,9; 5,3 i 9 wg% tego pierwiastka. Parametry napawania były jednakowe dla wszystkich proszków. Otrzymane warstwy różniły się twardością na powierzchni...
-
Effect of laser heating on cavitation behaviour of Fe-Cr-Mn coating.
PublicationW pracy przedstawiono badania odporności kawiracyjnej napoiny Fe-Cr-Mn po obróbce laserowej polegającej na przetapianiu napoiny wiązką lasera CO2 o mocy 1000W oraz jej nagrzewaniu w stanie stałym. Rezultaty badań wskazują,że po każdym rodzaju obróbki występuje inna podatność obrobionej powierzchni do odkształceń plastycznych pod działaniem obciążeń kawitacyjnych.
-
Research on deformations of laser-welded joint of a steel sandwich structure model.
PublicationPrzedstawiono problemy związane z zachowaniem złącza laserowego pod obciążeniem zginającym. Pokazano wyniki badań laboratoryjnych dla określenia mechanizmu pracy złącza i przedyskutowano uzyskane rezultaty.
-
Cavitation erosion of steels processed by CO2 laser beams of various parameters.
PublicationPrzedstawiono wpływ parametrów przetapiania stali za pomocą wiązki lasera CO2 na jej własności kawitacyjne. Do badań użyto stali 45, 2H13 i OH18N9. Wyniki badań wskazują na znaczny wpływ parametrów przetapiania na poziom odporności kawitacyjnej stali.
-
Processes and the Resulting Water Quality in the Medium size Turawa Storage Reservoir after 60 Year Usage
PublicationThe Turawa reservoir built on the Mała Panew river is one of important storage reservoirs in Poland. Quite many physico-chemical parameters of water in the reservoir itself and also in the reservoir inflowing rivers at different times of the year were measured and compared. The changes of water characteristics as well as their reasons and consequences were discussed.
-
Ophthalmic Surgery Lasers & Imaging Retina
Journals