Filters
total: 1989
displaying 1000 best results Help
Search results for: PITTING CORROSION
-
Corrosion degradation of spacers – examination of changes in bone cement coating.
PublicationSpacer is a special implant used at the time of infection after endoprosthetic surgery. It consists of a metal core and bone cement coating with an antibiotic. In the human body spacers are exposed to degradation processes. This paper looks at the effect of corrosion on spacers. Electrochemical corrosion tests were performer on titanium pins with bone cement coating in two solutions: Ringer’s solution and artificial...
-
Case Study of Stray Current Corrosion of Tall Ship Mast
PublicationNowadays, in the present technical civilization there are numerous complex technical systems that may generate various hazards. Large transport units like ships can be considered as the most dangerous systems. Therefore, it is important to eliminate all possible hazards, especially for ship crewmembers. Destruction of ship structural components caused by vast corrosion is one of these hazards. Usually, its activity leads to a decrease...
-
Corrosion behavior of concrete produced with diatomite and zeolite exposed to chlorides
PublicationChloride induced reinforcement corrosion is widely accepted to be the most frequent mechanism causing premature degradation of reinforced concrete structures. The electrochemical impedance of reinforcing steel in diatomite- and zeolite-containing concrete exposed to sodium chloride was assessed. Chemical, physical and mineralogical properties of three concrete samples (20% diatomite, 20% zeolite, and a reference containing neither)...
-
The application of impedance measurements for the determination of the probability of the course of corrosion processes
Publication -
Corrosion rate measurements by non-linear electrochemical impedance spectroscopy
Publication -
AE testing of local corrosion in storage tanks of oil tankers
PublicationW artykule przedstawiono wyniki badań korozji lokalnej w zbiornikach magazynowych zbiornikowców, przy użyciu metody Emisji Akustycznej. Badania wykrywania korozji wykonano z użyciem testerów, podczas produkcji których przyjęto założenie wysokiej intensywności sygnału oraz stabilności sygnału akustycznego w relatywnie długim czasie.
-
Concrete corrosion against penetration of mineral oil application of impregnants
PublicationOleje stanowią związki organiczne, w skład których wchodzą kwasy tłuszczowe nasycone i nienasycone oraz gliceryny różnego rodzaju. W zależności od rodzaju i właściwości olejów agresywność ich w stosunku do betonu jest różna. Olej izoluje dostęp wody do składników betonu, dlatego nie następuje dalsza hydratacja i przyrost wytrzymałości. Przesycenie betonu olejami powoduje wskutek obniżenia tarcia wewnętrznego tworzywa obniżenie...
-
The Influence of Casein Coatings on the Corrosion Behavior of Mg-Based Alloys
Publication -
High temperature corrosion of evaporator tubes with thermal sprayed coatings
PublicationDegradation examinations of outer surface of low-emission steam boiler evaporator tubes are presented in the paper. Metallographic evaluation of scale morphology, its micro sites chemical composition analysis and distribution of elements on cross sections have been performed. Water-wall tubes were exposed in steam boiler for up to two years period. Common tubes made of 16Mo3 steel suffered sulphide and molten salts corrosions....
-
Influence of burnishing on stress corrosion cracking susceptibility of duplex steel
PublicationNa próbkach ze stali duplex poddanych procesom nagniatania przeprowadzono badania podatności do naprężeniowego pękania korozyjnego. Przeprowadzono testy odkształcania z małą prędkością w środowisku wrzącego 35% MgCl2 i środowisku obojętnym- glicerynie. Stwierdzono zwiększoną odporność korozyjną stali po procesach nagniatania z niewielkim stopniem zgniotu. Stwierdzono, że zgniot powierzchniowy ma wpływ na przebieg procesu korozyjnego...
-
Microstructural aspects of corrosion of the SUPERSTON alloy after laser treatment
PublicationW artykule przedstawiono rezultaty obróbki laserowej stopu SUPERSTON w warunkach kriogenicznych i jej wpływ na mikrostrukturę i odporność korozyjną. Badania korozyjne zostały zrealizowane metodą potencjostatyczną w 3% NaCl, odporność korozyjna stopu zmieniała się wraz ze zmianą parametrów nadtapiania laserowego.
-
Corrosion resistance of dissimilar austenite and duplex steels welded joints
PublicationW artykule przedstawiono wpływ warunków spawania, a zwłaszcza energii liniowej, na odporność korozyjną złączy różnoimiennych stali austenitycznej 316L i typu duplex 2203. Przedstawiono wyniki testów korozyjnych:korozji wżerowej wg ASTM G48 oraz korozji naprężeniowej badanej w próbach odkształcania z małą pędkością w środowisku roztworu chlorku magnezowego.
-
Mechanical properties and corrosion resistance of dissimilar stainless steel welds
PublicationW artykule przedstawiono właściwości mechaniczne oraz odporność korozyjną doczołowych złączy różnoimiennych stali odpornych na korozję, austenitycznej 316L oraz duplex 2205. Blachy o grubości 15 mm spawano automatycznie łukiem krytyn z różnymi energiami liniowymi. Wykazano, że właściwości mechaniczne złączy spełniają wymagania okrętowych towarzystw klasyfikacyjnych, natomiast najbardziej narażoną strefą złącza na działanie korozji...
-
Assessment of evaporator tubes corrosion in low-emission steam boilers
PublicationW artykule przedstawiono wyniki badań rur ekranowych(16Mo3) kotła niskoemisyjnego po jednym roku i dwóch latach eksploatacji. Powierzchnie rur pokryte zostały warstwami natryskiwanymi cieplne - pojedynczą ze stopu 70%Ni 30%Cr i podwójną Ni-30Cr /Al2O3. Rury bez powłok natryskiwanych wykazywały pocienienie ze względu na działanie korozji siarkowej oraz korozyjnego oddziaływania warstwy stopionych soli. Pojedyncza warstwa 70%Ni 30%Cr...
-
Coatings for improvement of high temperature corrosion resistance of porous alloys
PublicationPorowate stopy metaliczne są potencjalnymi podłożami nośnymi dla tlenkowych ogniw paliwo. Ich stosowanie obniża cenę ogniw paliwowych, co zaowocuje ich szybszą komercjalizacą. Jednak są one podatne na korozję w wysokich temperaturach. Dotychczas brak jest metod, które mogą poprawić rezystancję korozyjną porotawych stopów w wysokich temperaturach porowatych stopy do zastosowań SOFC. W tym artykule zaproponowano sposób na poprawę...
-
Long-Term Performance of Ultrafiltration Membranes: Corrosion Fouling Aspect
Publication -
Magnetic composite adsorbents of phenolic compounds with superior corrosion resistance
Publication -
Formation of High Corrosion Resistant Nanotubular Layers on TitaniumAlloy Ti13Nb13Zr
PublicationThis paper presents results of oxidation tests and corrosion investigations of titanium alloy Ti13Nb13Zr performed at different conditions. The oxide layers have been formed by electrochemical method in 2M H3PO4 + 0.3% HF solution for 30 min. and 1 h at 20 V constantvoltage. The corrosion tests have been made by potentiodynamic method in Ringer`s solution at pH ranged between 3 and 7. It has been shown that the nano-oxide films,...
-
Experimental and numerical identification of corrosion degradation of ageing structural components
PublicationThe study presents experimental and numerical identification of corrosion degradation of thin-walled structural components employing guided wave propagation. The steel structural components are subjected to through-thickness varying corrosion degradation levels. The developed approach using the non-destructive guided wave-propagation quantifies the equivalent average corrosion degradation level by exploring a limited number of...
-
Selection of Organic Coating Systems for Corrosion Protection of Industrial Equipment
PublicationThe most important element of corrosion protection in industrial conditions is the protective coating system. However, selecting the right coating can often be a real problem due to the sheer number of coating manufacturers and their products on the market. A quantitative approach based on the data mining technique used to analyze the obtained multi-site exposure data has been proposed. This was demonstrated by the example of the...
-
Sodium nitrite as a corrosion inhibitor of copper in simulated cooling water
PublicationThe corrosion inhibition behavior of sodium nitrite (NaNO2) towards pure copper (99.95%) in simulated cooling water (SCW) was investigated by means of electrochemical impedance spectroscopy (EIS) and dynamic electrochemical impedance spectroscopy (DEIS). NaNO2 interferes with metal dissolution and reduce the corrosion rate through the formation or maintenance of inhibitive film on the metal surface. Surface morphologies illustrated...
-
Intergranular Corrosion Detection Using Electromagnetic Transducers for Ultrasonic Testing
PublicationThe aim of this paper is to create a research methodology that allows a quick analysis of the structural state of high alloy austenitic steels using non-destructive ultrasonic tests, in contrast to destructive standard methods. Electromagnetic acoustic transducers (EMAT) are used to generate and receive the ultrasonic wave and detect the microstructural changes caused by sample sensitization in elevated temperature, even after...
-
Wet H2S corrosion and degradation of pipeline in amine regeneration system
PublicationThe paper presents the results of NDT examinations, metallographic tests and risk assessment of degradation related to corrosion of amine regeneration unit in a desulphurisation system. Intensive corrosion resulting from acid gases environment upon water condensation causes perforation of the pipeline. Detailed analysis reveals cracking related to the mechanism of wet H2S. Hydrogen penetration, resulting from the wet H2S process,...
-
Nondestructive global corrosion measurement using guided wavefield data
PublicationMetallic structures often face degradation, and corrosion ranks among the most prevalent forms of deterioration. Accurate quantification of corrosion is crucial, especially for structures exposed to harsh environmental conditions, such as marine vessels and offshore installations. Because the traditional measurement methods based on scanning by ultrasonic gauge are time-consuming and provide only rough information on the thickness...
-
Applications of electrochemical noise technique in stress corrosion cracking diagnosis
PublicationW pracy przedstawione zostały rezultaty analizy prądowego szumu elektrochemicznego, generowanego podczas korozji naprężeniowej próbek stali stopowej. W przeciwieństwie do tradycyjnych metod analizy nie zakładano stacjonarności analizowanych sygnałów. Zamiast tego analizie poddana została zmodyfikowana widmowa odpowiedź szumowa o charakterze zależnym od czasu. Rezultaty badań skonfrontowano z wynikami otrzymanymi za pomocą techniki...
-
Study on the time-frequency analysis of nonstationary, electrochemical and corrosion processes
PublicationW pracy przedstawiono możliwości zastosowania czasowo-częstotliwościowych metod analizy sygnałów do badania niestacjonarnych procesów elektrochemicznych, chemicznych i korozyjnych. Wnikliwej analizie z wykorzystaniem metod STFT, rozkładu Wignera-Ville'a oraz przekształceń z klasy Cohena poddano rejestry oscylacji chemicznych, elektrochemicznych i rejestry korozji wżerowej.
-
Zniszczenie korozyjne wymiennika ciepła = Corrosion failure of a heat exchanger
PublicationPłytowy wymiennik ciepła ze stali 316L uległ zniszczeniu po trzech latach eksploatacji, wskutek perforacji po czyszczeniu nieodpowiednim środkiem czyszczącym.
-
Application of higher order spectra in harmonic analysis of corrosion process
PublicationZjawiska nieliniowe są niezwykle często spotykane w praktyce badań elektrochemicznych i korozyjnych. Typowym przykładem są procesy elektrodowe kontrolowane szybkością przeniesienia ładunku. Często stosowanym w takich przypadkach podejściem jest aproksymacja fragmentu krzywej prąd-napięcie za pomocą charakterystyki liniowej. W niniejszej pracy autorzy prezentują możliwość wykorzystania pomiarów składowych harmonicznych do oceny...
-
Elektrochemiczne polaryzacyjne badania korozyjne = Elecrochemical polarisation corrosion testing
PublicationW pracy przedstawiono sposoby określania szybkości korozji metali na podstawie analizy krzywych polaryzacyjnych.
-
Modelling of cutting by means of fracture mechanics
PublicationThe suitability of modern fracture mechanic theory was proved for the estimation of the cutting force and the cutting specific resistance. This paper shows modification of Ernst-Merchant theory and its application for determination some other properties of wood sample. This theory is acceptable for evaluation of shear yield stresses and shear plane angle. Sawing by gang saw machine was used as a process similar to the orthogonal...
-
MODELLING OF CUTTING BY MEANS OF FRACTURE MECHANICS
PublicationThe suitability of modern fracture mechanic theory was proved for the estimation of the cutting force and the cutting specific resistance. This paper shows modification of Ernst-Merchant theory and its application for determination some other properties of wood sample. This theory is acceptable for evaluation of shear yield stresses and shear plane angle. Sawing by gang saw machine was used as a process similar to the orthogonal...
-
Three-Dimensional Printing of Bone Models
PublicationThe trabecular bone occurs, for example, in the femoral heads. Understanding the phenomenon of bone tissue degeneration can be the basis for the possibility of looking for alternative methods of surgical treatment of bone loss. The paper presents the results of the trabecular bone model, which was produced in additive manufacturing method with fused filament fabrication technology. The verification of the mechanical behavior of...
-
Physicochemical treatment of used cutting fluids
PublicationBadano fizykochemiczne oczyszczanie przepracowanych cieczy obróbkowych pobranych z różnych źródeł przez rozdzielanie na frakcje: organiczną i wodną. Stosowano różne koagulanty (m.in. siarczan żelaza, chlorek żelaza) oraz polielektrolit Polyquant 20 U 050. Do wyznaczenia szybkości rozdziału emulsji wykorzystano Turbiscan Lab Expert. Ponadto wyznaczono optymalne warunki rozdziału faz emulsji (pH, temperatura oraz dawki koagulanta...
-
Macromodeling of multiport systems using a fast implementation of the vector fitting method
PublicationMakromodelowanie układów wieloportowych przy użyciu vector fittingu jest czasochłonne oraz wymaga dużych zasobów obliczeniowych w przypadku gdy wszystkie elementy macierzy systemowej dzielą wspólne bieguny. Artykuł prezentuje stabilne rozwiązanie, które usuwa problem rzadkości macierzy poprzez zastosowanie bezpośrednie dekompozycje QR. Jako przykład przedstawiony został 60 portowy układ, który ilustruje oszczędność czasu potrzebnego...
-
Onychophagia (Nail Biting): an overview
Publication -
EVALUATION OF CAUSES OF CORROSION OF HEATING PIPES AND BALLAST CHAMBERS ON HLVJ INNOVATION
Publication..
-
Effects of the preheating laser treatment on microstructure and corrosion resistance of Ti6Al4V bioalloy
PublicationThe laser remelting of the Ti6Al4V alloy was made on specimens pre-heated at elevated temperatures. The laser treatment effected in change of microstructures of surface layers and an appearance of blisters and numerous cracks. The corrosion tests demonstrated the decrease in corrosion resistance for each preheating temperature. The observed effects were attributed to negative influence of excessive compressive stresses with no...
-
Detection of stress corrosion cracking dynamics by dynamic electrochemical impedance spectroscopy
Publication -
Corrosion and hydrogen intake for some Cr-Mn steels in liquid hydrocarbons
PublicationStal 34HNM i 26H2MF, poddana różnym obróbkom cieplnym wykazała skłonność do korozji naprężeniowej przy pomiarach ze stałą szybkością rozciągania (10-6s-1) i pomiarach niskocyklowego zmęczenia, wykonanych w paliwie kotłowym. Mechanizm korozji naprężeniowej określono jako kruchość wodorowa, co zostało potwierdzone w pomiarach pochłaniania wodoru z tych środowisk. Jako możliwe źródła wnikania wodoru do stali omówiono procesy korozyjne,...
-
Investigations into tendency to stress corrosion of joints welded in austenitic and duplex steels
PublicationPrzedstawiono wyniki badań spawanych złączy różnoimiennych wykonanych ze stali austenitycznej oraz typu duplex 2205. Badania podatności do korozji naprężeniowej złączy wykonano metodą odkształcania z małą prędkością. Próby przeprowadzono w środowisku obojętnym oraz agresywnym (MgCl2).
-
High temperature corrosion of evaporator tubes in low-emission steam boilers
PublicationW artykule opisano zjawisko korozji wysokotemperaturowej rur ekranowych kotłów parowych niskoemisyjnych. Przeprowadzono badania rur po eksploatacji. Wykonano badania składu chemicznego zgorzelin. Stwierdzono, że główną przyczyną pocienienia rur na wyższych poziomach jest korozja siarkowa, natomiast na poziomach niższych oddziaływanie stopionych soli.
-
High temperature corrosion of stainless steels for Solid Oxide Fuel Cells
PublicationW pracy przedstawiono wyniki korozyjności wysokotemperaturowej stali litych i porowatych stosowanych w tlenkowych ogniwach paliwowych.
-
Tribological and corrosion testing of surface engineered surgical grade CoCrMo alloy
Publication -
Diaryl Sulfide Derivatives as Potential Iron Corrosion Inhibitors: A Computational Study
PublicationThe present work aimed to assess six diaryl sulfide derivatives as potential corrosion inhibitors. These derivatives were compared with dapsone (4,4′-diaminodiphenyl sulfone), a common leprosy antibiotic that has been shown to resist the corrosion of mild steel in acidic media with a corrosion efficiency exceeding 90%. Since all the studied compounds possess a common molecular backbone (diphenyl sulfide), dapsone was taken as the...
-
Carboxylic acids as efficient corrosion inhibitors of aluminium alloys in alkaline media
PublicationThe efficiency of AA5754 aluminium alloy corrosion inhibition achieved with maleic, malic, succinic, tartaric, citric, tricarballylic acids and serine in alkaline environment (pH 11) was examined. Selected corrosion inhibitors are characterized by different numbers and distribution of carbonyl and hydroxyl groups within their molecules. We have proposed and verified a novel approach for determining the adsorption isotherms based...
-
Novel fast non-linear electrochemical impedance method for corrosion investigations
PublicationThe paper presents a novel approach to corrosion rate monitoring using non-linear electrochemical impedance spectroscopy. The authors propose a new variant of non-linear impedance measurement using amplitude-modulated multi-frequency ac perturbation signal. It allows shortening of measurement duration so it is possible to monitor corrosion rate of the systems experiencing rapid changes. In this way a limitation resulting from lack...
-
Hydrogen-enhanced stress corrosion cracking in low alloy steels in seawater
PublicationBadano podatność stali niskostopowych w wodzie morskiej w warunkach polaryzacji katodowej. Stwierdzono spadek czasu do zniszczenia, energii zniszczenia i przewężenia ze wzrostem potencjału katodowego. Wykazano znaczącą korelację między stopniem degradacji wodorowej a stężeniem wodoru dyfuzyjnego.
-
Corrosion monitoring of selected metals in artificial seawater by harmonic synthesis method
PublicationPrzedstawiono podstawy teoretyczne nowej metody elektrochemicznej nazwanej metodą syntezy harmonicznej (SH). Metoda jest oparta na pomiarach pierwszych trzech składowych harmonicznych prądu generowanego przez korodującą elektrodę po pobudzeniu sinusoidalnym sygnałem napięciowym bardzo niskiej częstotliwości. Na tej podstawie rekonstruowana jest dyskretna quasi-stacjonarna charakterystyka polaryzacyjna elektrody. Jej analiza numeryczna...
-
A probabilistic-driven framework for enhanced corrosion estimation of ship structural components
PublicationThe work proposes a probabilistic-driven framework for enhanced corrosion estimation of ship structural components using Bayesian inference and limited measurement data. The new approach for modelling measurement uncertainty is proposed based on the results of previous corrosion tests that incorporate the non-uniform character of the corroded surface of structural components. The proposed framework's basic features are outlined,...
-
Risks caused by microbiologically influenced corrosion in diesel fuel storage tanks
PublicationMicrobiologically influenced corrosion (MIC) poses serious problems for the petrochemical and refinery industries. Particularly favourable conditions for MIC arise in storage tanks and transmission pipelines for mixtures of diesel oil with the addition of a biocomponent (in Poland 7%). The best conditions for the development of MIC occur at the fuel-water interface, where microorganisms are provided with a source of food and water,...