Filters
total: 1858
displaying 1000 best results Help
Search results for: TITANIUM FOIL
-
Laser-assisted modification of titanium dioxide nanotubes in a tilted mode as surface modification and patterning strategy
PublicationElectrochemical anodization is regarded as a facile and easily scalable fabrication method of titania nanotubes (TiO2NTs). However, due to the extended duration of calcination and further modifications, much faster alternatives are highly required. As a response to growing interest in laser modification of nanotube arrays, a comprehensive investigation of pulsed-laser irradiation and its effect onto TiO2NT properties has been carried out....
-
Fatigue of titanium alloy Ti6Al4V with diamond structure obtained by Laser Power Bed Fusion method
PublicationThis paper presents the results of fatigue tests conducted on Ti6Al4V titanium alloy with diamond structure obtained by the Laser Power Bed Fusion method. Samples used in tests were printed with porosities: 81%, 73%, 50%, 34% and near-zero porosity. Samples were subjected to cyclic tests with a constant stress amplitude. The number of cycles until sample failure was registered. Obtained fatigue test results made it possible to...
-
Studies on Silver Ions Releasing Processes and Mechanical Properties of Surface-Modified Titanium Alloy Implants
PublicationDispersed silver nanoparticles (AgNPs) on the surface of titanium alloy (Ti6Al4V) and titanium alloy modified by titania nanotube layer (Ti6Al4V/TNT) substrates were produced by the chemical vapor deposition method (CVD) using a novel precursor of the formula [Ag5(O2CC2F5)5(H2O)3]. The structure and volatile properties of this compound were determined using single crystal X-ray diffractometry, variable temperature IR spectrophotometry...
-
Nanoporous TiO2 electrode grown by laser ablation of titanium in air at atmospheric pressure and room temperature
PublicationRecently, fabrication of the nanoporous TiO2 photoelectrode on metal foils by means of sputtering of the Ti film on preheatedmetal substrate followed by the TiO2 deposition (doctor blade technique) and sintering represents the frequently applied technique. This is despite the relatively complicated procedure and number of parameters to be controlled in order to fabricate films of required properties. In this work an approach is...
-
SOIL DYNAMICS AND EARTHQUAKE ENGINEERING
Journals -
Environmentally friedly propeller shaft support with the use of water lubricated foil bearings
PublicationW pracy przedstawiono podsumowanie prowadzonych badań w celu opracowania oryginalnej metodyki projektowania oraz technologii wykonania pierwszego w świecie łożyska foliowego smarowanego wodą. Zaprezentowano koncepcje nowego łożyska foliowego poprzecznego oraz opisano opracowany algorytm obliczeniowy wykorzystany do predykcji jego charakterystyk. W rezultacie prowadzonych prac opracowano i przebadano doświadczalnie na stanowisku...
-
New Generation of Water lubricated Foil bearing - Numerical Models and Experimental Verification
PublicationIn the paper a new idea of foil water lubricated bearing and methodology of hydrodynamic characteristics calculations is presented. To assesses the theoretical characteristics of these bearings two different computer models were built. First is structural model coupled with fluid model. It takes into account: fluid flow in the deformed fluid gap, specific design of bearing support and friction in bearing support. The second is...
-
Soil enzymes in a changing climate
Publication -
Pro-Fil
Journals -
OIL SHALE
Journals -
EURASIAN SOIL SCIENCE
Journals -
Soil and Water Research
Journals -
Journal of Soil Science
Journals -
Rock and Soil Mechanics
Journals -
Soil Ecology Letters
Journals -
SOIL BIOLOGY & BIOCHEMISTRY
Journals -
Long-term effect of ZnO and CuO nanoparticles on soil microbial community in different types of soil
Publication -
Assessment of soil microbial diversity measurements as indicators of soil functioning in organic and conventional horticulture systems
Publication -
Mobility and biodegradability of an imidazolium based ionic liquid in soil and soil amended with waste sewage sludge
PublicationSorption on solids and biodegradation are main phenomena that can mitigate the pollution of soil and water by ionic liquids (ILs). ILs sorbed on soil particles become immobilized (temporarily or permanently) which prevents them from spreading into deeper layers of soil or groundwater but which also makes them less bioavailable. In this study we attempt to examine if amendment of soil with waste sludge has a potential to mitigate...
-
No apparent effect of invasive alien goldenrod on soil microbial communities or soil fauna feeding activity
Publication -
Evaluation of Antifungal Properties of Titania P25
Publication -
Titania modification for photocatalytic wastewater treatment.
PublicationW celu polepszenia efektywności katalitycznej za pomocą separacji ładunkowe-/n+ TiO2 został zmodyfikowany jonami i klasterami platyny. Badania degradacji z wykorzystaniem promieniowania UV wykazały, że domieszkowanie powierzchniowe (adsorpcja) powoduje znaczne zwiększenie efektywności katalizatora od domieszkowania wewnętrznego
-
Effect of Electron Beam Power Density on the Structure of Titanium Under Non-Vacuum Electron-Beam Treatment
Publication -
Titanium(IV) Oxide Modified with Activated Carbon and Ultrasounds for Caffeine Photodegradation: Adsorption Isotherm and Kinetics Study
Publication -
Titanium Dioxide Nanoparticles in Food and Personal Care Products—What Do We Know about Their Safety?
Publication -
Graphitic Carbon Nitride and Titanium Dioxide Modified with 1 D and 2 D Carbon Structures for Photocatalysis
Publication -
The Influence of the Parameters of a Gold Nanoparticle Deposition Method on Titanium Dioxide Nanotubes, Their Electrochemical Response, and Protein Adsorption
Publication -
Thermally tuneable optical and electrochemical properties of Au-Cu nanomosaic formed over the host titanium dimples
PublicationAu-Cu nanostructures offer unique optical and catalytic properties unlike the monometallic ones resulting from the specific interaction. Among others, they have the ability to exhibit surface plasmon resonance, electrochemical activity towards the oxygen and hydrogen evolution reaction (OER, HER) as well as improved photoresponse in relation to monometalic but those properties depend highly on the substrate where bimetallic structures...
-
Biological and antibacterial properties of chitosan-based coatings with AgNPs and CuNPs obtained on oxidized Ti13Zr13Nb titanium alloy
PublicationDespite numerous studies, the antibacterial efficiency and cytotoxicity of chitosan-based coatings with nanometals need further studies. The purpose of this research was to determine the biological properties of chitosan coatings implemented with either silver nanoparticles (AgNPs) or copper nanoparticles (CuNPs), that were electrophoretically deposited on electrochemically oxidized Ti13Zr13Nb alloy. The SEM tests were used to...
-
A study of cavitation erosion resistance of an ion nitrided titanium alloy by means of the vibration and rotating disk methods
PublicationIn this work, a comparative analysis of the cavitation erosion resistance of the Ti– 6.7Al–2.5Mo–1.8Cr–0.5Fe–0.25Si alloy (known as brand VT3-1) before and after lowtemperature ion nitriding is carried out. Two test methods were applied, using vibrative (ASTM G-32) and rotating disk rigs, respectively. The kinetic dependences of the erosive destruction of samples of titanium alloy VT3-1 in the initial state, after ion nitriding...
-
Antibacterial properties of laser-encapsulated titanium oxide nanotubes decorated with nanosilver and covered with chitosan/Eudragit polymers
PublicationTo provide antibacterial properties, the titanium samples were subjected to electrochemical oxidation in the fluoride-containing diethylene glycol-based electrolyte to create a titanium oxide nanotubular surface. Afterward, the surface was covered by sputtering with silver 5 nm film, and the tops of the nanotubes were capped using laser treatment, resulting in an appearance of silver nanoparticles (AgNPs) of around 30 nm in diameter...
-
Effect of high loading of titanium dioxide particles on the morphology and selected properties of natural rubber-based composites
PublicationThe aim of this work was to prepare and characterize the natural rubber vulcanizates contained different amounts of titanium dioxide particles. At first rubber mixture was prepared using a laboratory two-roll mill and then samples were vulcanized in a hydraulic press. The formulation of rubber mixture and rubber-processing technique is based on our earlier investigations. Materials were obtained at the different titanium dioxide...
-
Ordered titanium templates functionalized by gold films for biosensing applications – Towards non-enzymatic glucose detection
PublicationRecently, metal nanostructures evoke much interest due to application potential in highly sensitive detectors in biochemistry and medical diagnostics. In this work we report on preparation and characteristics of thin (1–100 nm) Au films deposited onto highly ordered structured titanium templates for SERS (Surface Enhanced Raman Spectroscopy) and electrochemical sensing. The Ti templates are formed by selective removal of TiO2 nanotubes...
-
Structural properties of foil bearings: a closed-form solution validated with finite element analysis
PublicationFluid film thickness in a compliant foil bearing is greatly influenced by the deflection of the bearing structure. Therefore, in order to properly model performance of a foil bearing, it is mandatory that the deflection of the compliant bearing structure due to the generated hydrodynamic pressure is determined accurately. This article proposes an easy-to-use two-dimensional model, which takes into account detailed geometry of the...
-
Technology of braze welding absorber tubes to copper foil in solar collectors by the GTA method
Publication -
Conductive printable electrodes tuned by boron-doped nanodiamond foil additives for nitroexplosive detection
PublicationAn efficient additive manufacturing-based composite material fabrication for electrochemical applications is reported. The composite is composed of commercially available graphene-doped polylactide acid (G-PLA) 3D printouts and surface- functionalized with nanocrystalline boron-doped diamond foil (NDF) additives. The NDFs were synthesized on a tantalum substrate and transferred to the 3D-printout surface at 200 °C. No other electrode...
-
UV/VIS Spectroscopy of titanium dioxide coated nickel foams
Open Research DataThe data includes UV-Vis spectra of titanium dioxide coated nickel foams heated at 400, 500 and 600 C in Ar. Jasco V-650 Spectrophotometer was used and Spectra Measurement software.
-
The influence of microstructure on the corrosion resistance for some titanium-based alloys
Open Research DataThis dataset contains scanning electron microscopy (SEM) micrographs revealing the microstructure of some Ti-based alloys, namely: Ti-6Al-4V (file name: TiV), Ti-6Al-7Nb (file name: TiNb) and TC21 (file name: TiAlSnZrMoCrNbSi) alloys and their localized corrosion as a result of passive layer breakdown in a corrosive environment, ie. 0.9% NaCl solution...
-
Topography and microstructure of phosphate-iron glasses containing niobium and titanium
Open Research DataThe topography and microstructure of phosphate-iron glasses containing niobium and titanium were investigated by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM). Glass samples of the composition of 35P2O5-30Fe2O3-(35-x)Nb2O5-xTiO2 where x= 0; 7.5 and 15 (in %mol) were prepared by the conventional melt quenching technique. Appropriate...
-
Depth XPS profile of Fe-S layers on a titanium substrate
Open Research DataDepth XPS profile of Fe-S layers on a titanium substrate was measured. Material was etched by Argon ion gun and measured by XPS method. For each sample, three times per 10 minutes each was sputtered.
-
Soil organic carbon, macro- and micronutrient changes in soil fractions with different lability in response to crop intensification
Publication -
The impact of addition of olive oil on thermal degradation of refined rapeseed oil
PublicationFats are an important component of the everyday diet and have a significant impact on the proper functioning of human organism. However, during the process of frying chemical transformations take place in the oil; hence fats characterised by high oxidative stability should be given preference. The aim of this work was to determine the quality of rapeseed oil, blended oil, and refined olive oil, all sourced from the domestic market....
-
Reasearch on reinforced soil and geosynthetics in Poland.
PublicationOmówienie badań wzmocnienia gruntu w Polsce zapoczątkowane w latach 70-tych w Katedrze Geotechniki Politechniki Gdańskiej i Instytucie Budownictwa Wodnego PAN w Gdańsku. Ponadto przedstawiono: badania tarcia w geomembranach teksturowanych; nośność wzmocnionego geotekstyliami podłoża gruntowego obciążonego fundamentem wyciąganym; badania na wyciąganie (''pull-out'') geogrydów wzmacniających podłoża.
-
Soil improvement by short stone columns.
PublicationW artykule przedstawiono sposób dogęszczania podłoża gruntowego wykorzystywany do renowacji istniejących nawierzchni placów składowych i dróg. Proponowany sposób polega na formowaniu w gruncie kolumny o niewielkiej średnicy. Kolumnę tą formuje się poprzez wbijanie w rozluźnione podłoże trzpienia stalowego, z jednoczesnym dosypywaniem gruntu.Sposób ten stosuje się przede wszystkim jako metodę wzmocnienia podłoża pod nawierzchniami...
-
Soil mechanics and old buildings foundations
PublicationPraca dotyczy sposobów fundamentowania obiektów zabytkowych. Przeanalizowano historyczny rozwój sposobów posadowienia poczynając od starożytności, poprzez średniowiecze aż do czasów nowożytnych. Omówiono charakterystyczne dla kolejnych okresów historycznych rodzaje fundamentów. Przedstawiono przykłady dobrego i złego fundamentowania.
-
Ground improvement with in situ Soil Mixing
PublicationOmówiono metodę wzmacniania słabego gruntu za pomocą technologii wgłębnego mieszania na sucho i mokro. W metodzie mokrej stosuje się składniki wiążące (głownie cementy) wymieszane z wodą, podawane w formie zaczynu. W metodzie suchej materiały wiążące podawane są w postaci sproszkowanej z udziałem sprężonego powietrza. Przedstawiono główne obszary zastosowania w geotechnice oraz podano przykłady kilku realizacji.
-
On the mechanisms of soil remediation with use of surfactants
PublicationPrzedstawiono problem zanieczyszczenia gruntów substancjami olejowymi. Zaprezentowano metodę remediacji za pomocą przemywania roztworami surfaktantów. Omówiono mechanizmy biorące udział w usuwaniu zanieczyszczeń z gruntu podczas tego procesu.
-
Dynamic soil improvement by hybrid technologies
PublicationHybrid method of subsoil improvement for road embankment foundation is described. This method is composed of two wellknown methods: dynamic replacement (DR) and microblasting (DDC) one (Deep Dynamic Compaction). The method was used for both the strengthening of the fully saturated organic subsoil as well as for acceleration of the consolidation of the organic layers. The practice ensures the expected results. A proper example on...
-
FE simulations of a soil structure interface.
PublicationPrzedstawiono warunki brzegowe do opisu szorstkości ściany konstrukcji w kontakcie z gruntem. Wykonano doświadczenia i symulacje MES na bazie mikropolarnego prawa hipoplastycznego.
-
Thickness and structure change of titanium(IV) oxide thin films synthesized by the sol–gel spin coating method
Publication