displaying 1000 best results Help
Search results for: MULTIPHASE FLOWS
-
Modeling of entrained flow steam gasification of sewage sludge
PublicationProper management of sewage sludge becomes increasingly problematic due to legal requirements aiming at diminishing environmental impact, as well as rationalizing the utilization from the point of view of logistics. Steam gasification of sewage sludge can result in very good quality of the producer gas. So far, the works have been focused on the gasification in fixed bed gasifiers. However, this does not allow to take full advantage...
-
Analysis of the radiation dose in UV-disinfection flow reactors.
PublicationTheoretical considerations devoted to the variation of UV radiation doses in flow disinfection reactors are presented. The minimal time required by the fluid to pass the reactor was determined and combined with the radiation intensity. The active zones of the reactor were determined.
-
Material Flow Analysis in a cooked mussel processing industry
PublicationGalicia (NW Spain) is an ideal environment for mussel culture owing to its excellent natural conditions. It is the first Spanish and European mussel producer and the second worldwide after China. More than 50% of the mussel collected in Galicia is used in the processing industry, which produces different products, as cooked mussel that is canned, frozen or used in the food industry. In this paper a methodology based on Life Cycle...
-
CFD Simulations and Tests of a Prototype Flow Control Valve
PublicationIn this paper a prototype of a flow control valve is described and numerically simulated. The flow control valve is used in hydraulic systems to maintain constant fluid flow despite changing loads of a receiver. The standard construction of this type of valves is modified mainly by eliminating the spring. The prototype consists the hydrostatically unloaded throttle valve and pressure ratio valve substituting pressure difference...
-
Analytical Steady-State Model of the Pipeline Flow Process
PublicationThe paper addresses the issue of modeling the flow process in transmission pipelines. A base model used for numerical simulation is introduced. Under certain assumptions concerning steady state analysis, the differential equations describing the process are solved analytically for two cases: zero and nonzero inclination angle α. These equations describe a constant flow rate and a corresponding distribution of the pressure along...
-
Experimental study on the seepage flow through the ice jam
PublicationIn light of the observed climate change, there is a need for better understanding of river ice processes for managing water resources in the cold regions. Ice jams produce significant resistance which may cause rise of water level and flooding. The jam resistance is only referred to the roughness of its underside, and this approach lead to exceptional roughness coefficients which has no physical explanation. Number of evidences...
-
Discrete-continuous optimisation of an axial flow blood pump
PublicationThis paper presents results of discrete-continuous optimisation of an axial flow blood pump. Evolution Strategies (ES) are used as a global optimisation method in order to localise the optimal solution in relatively short time. The whole optimisation process is fully automated. This also applies to geometry modelling. Numerical simulations of the flow inside the pump is performed by means of the Reynolds-Average Navier-Stokes...
-
Educational Dataset of Handheld Doppler Blood Flow Recordings
PublicationVital signals registration plays a significant role in biomedical engineering and education process. Well acquired data allow future engineers to observe certain physical phenomena as well learn how to correctly process and interpret the data. This dataset was designed for students to learn about Doppler phenomena and to demonstrate correctly and incorrectly acquired signals as well as the basic methods of signal processing. This...
-
Inverse Flood Routing Using Simplified Flow Equations
PublicationThe paper considers the problem of inverse flood routing in reservoir operation strategy. The aim of the work is to investigate the possibility of determining the hydrograph at the upstream end based on the hydrograph required at the downstream end using simplified open channel flow models. To accomplish this, the linear kinematic wave equation, the diffusive wave equation and the linear Muskingum equation are considered. To achieve...
-
CFD analysis of fluid flow through the labyrinth seal
PublicationSteam and gas turbines are some of the fundamental means of power generation. The energy efficiency of the turbines, however, is not satisfactory. Ever since the start-up of the first turbine in the world, engineers have been striving for their increased efficiency. Multiple solutions to the problem of steam loss in an operating turbine are available. The use of seals is one of them. Empirical methods or numerical calculations...
-
Confined granular flow in silos : experiments and numerical investigation
PublicationW monografii opisano niektóre charakterystyczne zjawiska mające miejsce podczas przepływów silosowych materiałów sypkich. Wykonano badania doświadczalne oraz obliczenia numeryczne celem wyjaśnienia zjawisk. Doświadczenia wykonano w dużych i małych silosach. Obliczenia wykonano przy zastosowaniu metody elementów skończonych opartej na hipoplastycznym modelu konstytutywnym dla materiałów sypkich.
-
Dynamic and tomography analysis of granular flow in cylindrical shell
PublicationW pracy przedstawiono wyniki badań ekperymentalnych dotyczących efektów dynamicznych występujących podczas przepływu materiałów sypkich w silosie cylindrycznym.
-
Application of a cellular automaton to simulations of granular flow in silos
PublicationA cellular automaton based on a gas model of hydrodynamics was used to calculate the kinematics of non-cohesive granular materials during confined flow in a mass flow and funnel flow model silo. In the model, collisions of particles were taken into account during granular flow. In addition, a simplified automaton was used wherein granular flow was assumed as an upward propagation of holes through a lattice composed of cells representing...
-
Silo music - mechanism of dynamic flow and structure interaction
PublicationArtykuł omawia zjawisko muzyki silosowe. Wykonano pomiary dynamiczne przyspieszeń, częstotliwości i postaci drgań własnych. Zaproponowano nowa hipotezę powstawania efektów dynamicznych podczas przepływu silosowego.
-
Reduction of dynamic effects during granular flow in silos
PublicationOmówiono kilka efektywnych sposobów redukcji nadmiernych dynamicznych efektów występujących w przepływie silosowym w silosach modelowych. Sposoby te mogą być wykorzystane w praktyce silosowej.
-
Silo music - mechanism of dynamic flow and structure interaction
PublicationArtykuł omawia zjawisko muzyki silosowej. Wykonano pomiary dynamiczne przyspieszeń, częstotliwości i postaci drgań własnych. Zaproponowano nowa hipotezę powstawania efektów dynamicznych podczas przepływu silosowego.
-
Aleksandra Parteka dr hab. inż.
PeopleAbout me: I am an associate professor and head of doctoral studies at the Faculty of Management and Economics, Gdansk University of Technology (GdanskTech, Poland). I got my MSc degree in Economics from Gdansk University of Technology (2003) and Universita’ Politecnica delle Marche (2005), as well as MA degree in Contemporary European Studies from Sussex University (2006, with distinction). I received my PhD in Economics...
-
Jarosław Guziński prof. dr hab. inż.
PeopleJaroslaw Guzinski received M.Sc., Ph.D. and D.Sc. degrees from the Electrical Engineering Department at Technical University of Gdansk, Poland in 1994, 2000 and 2011 respectively. Since 2016 he is Associate Professor at Gdansk University of Technology. Currently he is the head of the Department of Electric Drives and Energy Conversion. From 2006 to 2009 he was involved in European Commission Project PREMAID Marie Curie, ‘Predictive...
-
Rheology of polymer blends
PublicationPolymer blends are physical mixtures of two or more homopolymers or copolymers. This type of materials have wide spectrum of technological applications, and their properties are influenced, e.g., by the properties of single components and morphology of final material. The rheology of polymer blends is connected with the processing of polymer blends and is influenced by thermodynamics, morphology, and their evolution during testing....
-
Large eddy simulations of wall-bounded flows using a simplified immersed boundary method and high-order compact schemes
Publication -
Estimating the uncertainty of the liquid mass flow using the orifice plate
PublicationThe article presents estimation of measurement uncertainty of a liquid mass flow using the orifice plate. This subject is essential because of the widespread use of this type of flow meters, which renders not only the quantitative estimation but also qualitative results of this type so those measurements are important. To achieve this goal, the authors of the paper propose to use the theory of uncertainty. The article shows the...
-
Numerical Study of Turbulent Flow and Heat Transfer of Nanofluids in Pipes
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (Reynolds number between 6000 and 12000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Reduction of Computational Complexity in Simulations of the Flow Process in Transmission Pipelines
PublicationThe paper addresses the problem of computational efficiency of the pipe-flow model used in leak detection and identification systems. Analysis of the model brings attention to its specific structure, where all matrices are sparse. With certain rearrangements, the model can be reduced to a set of equations with tridiagonal matrices. Such equations can be solved using the Thomas algorithm. This method provides almost the same values...
-
Pressure drop of HFE7000 and HFE7100 during flow condensation in minichannels
PublicationAttention is focused on the issues of flow resistance and pressure drop of perspective refrigeration fluids during condensation in the two-phase flow in minichannels. The case of the flow through a cylindrical single channel of 2.3 mm inner diameter was carefully analyzed. Pressure drop tests have been performed in diabatic flow conditions. The effect of heat flux, mass flux, vapour quality and saturation temperature on the two-phase...
-
Flow of liquid in flat gaps of the satellite motor working mechanism
PublicationThe article describes the methodology and results of investigations of the flow of oil and HFA-E emulsion in flat gaps of the working mechanism of a satellite motor. The flow of liquid in those gaps is turbulent and not fully developed. The article presents two methods of modelling this flow. Method I makes use of the Darcy-Weisbach formula, while Method II bases on the assumption that in the variable-length gaps the flow is turbulent...
-
Selected studies of flow maldistribution in a minichannel plate heat exchanger
PublicationAnalysis of the state of-the-art in research of minichannel heat exchangers, especially on the topic of flow maldistribution in multiple channels, has been accomplished. Studies on minichannel plate heat exchanger with 51 parallel minichannels with four hydraulic diameters, i.e., 461 μm, 574 μm, 667 μm, and 750 μm have been presented. Flow at the instance of filling the microchannel with water at low flow rates has been visualized. The...
-
Analysis of radiometric signal in sedimentating suspension flow in open channel
PublicationThe article discusses issues related to the estimation of the sedimentating solid particles average flow velocity in an open channel using radiometric methods. Due to the composition of the compound, which formed water and diatomite, received data have a very weak signal to noise ratio. In the process analysis the known determining of the solid phase transportation time delay the classical cross-correlation function is the most...
-
Numerical study of turbulent flow and heat transfer of nanofluids in pipes
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (6 000 < Re < 12 000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data of Vajjha et al. [1]. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
NP-hardness of compact scheduling in simplified open and flow shops
Publication -
Power flow in typical series-parallel hybrid filters topologies
Publication -
Flow Boiling in Minigap in the Reversed Two-Phase Thermosiphon Loop
PublicationThe paper presents the results of experimental investigations of a model of a heat exchanger featuring a minigap, which is perceived as an evaporator for an inverted thermosiphon. The system works with a single component test fluid. The tested evaporator generates pumping power in the test loop in a way similar to the mammoth pump. The tests regarded a module of the heat exchanger, consisting of a hot leg and a cold leg with the...
-
The Discrete-Continuous, Global Optimisation of an Axial Flow Blood Pump
PublicationThis paper presents the results of the discrete-continuous optimisation of an axial flow blood pump. Differential evolution (DE) is used as a global optimisation method in order to localise the optimal solution in a relatively short time. The whole optimisation process is fully automated. This also applies to geometry modelling. Numerical simulations of the flow inside the pump are performed by means of the Reynolds-Average Navier-Stokes...
-
Uncertainty of the liquid mass flow measurement using the orifice plate
PublicationThe article presents an estimation of measurement uncertainty of a liquid mass flow using the orifice plate. This subject is essential because of the widespread use of this type of flow meters. Not only the quantitative estimation but also the qualitative results of those measurements are important. To achieve these results the authors of the paper propose to use the theory of uncertainty. The article shows the analysis of the...
-
On various modelling approaches to real-time visualisation of blood flow
PublicationThis paper reviews various modelling approaches to real-time visualisation of blood flow. These include classic, macroscale approach based on the momentum conservation equation together with a proper constitutive equation. Moreover, modern micro- and mesoscale approaches, such as molecular dynamics and dissipative particle dynamics, are discussed. Advantages and disadvantages of the discussed methods are highlighted with particular...
-
Analysis of unsteady flow forces on the thermowell of steam temperature sensor
PublicationIn this paper, 3D numerical analysis of unsteady flow forces acting on the measuring sheath of steam temperature is presented. According to that purpose, the CFD (Computation Fluid Dynamic [1]) approach has been used. The nonstationary of fluid acting on the measuring sheath such as: Strouhal frequency, amplitude of pressure, structure of vortex, peak of pressure, field of pressure, field of velocity etc. are studied analytically...
-
Approximate models and parameter analysis of the flow process in transmission pipelines
Publicationthe paper deals with the problem of early leak detection in transmission pipelines. First we present the derivation of state-space equations of the flow process in the pipelines. This description is then aggregated in order to obtain a principal model. Next, the problem of process model parameterization is addressed, taking into account the maximization of a model stability margin. The location of the maximum is determined using...
-
Numerical Analysis of Flow in Building Arrangement: Computational Domain Discretization
Publication -
Laboratorial studies on the seepage impact in open-channel flow turbulence
Publication -
Analysis of Turbulent Flow Measurements in a Flume with Induced Upward Seepage
Publication -
Flow cytometry as an estimation tool for honey bee sperm viability
Publication -
Design and evaluation of a flow-to-frequency converter circuit with thermal feedback
Publication -
Comparative study of flow condensation in conventional and small diameter tubes
PublicationFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena, however their description with a single correlation has yet to be suggested. In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the bubble generation is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationIn the paper a method developed earlier by the first author is applied to calculations of heat transfer coefficient for inside tube condensation. The method has been verified using experimental data from literature on several fluids in different microchannels and compared to three well established correlations.
-
Acoustic Heating Produced in the Thermoviscous Flow of a Shear-Thinning Fluid
PublicationThis study is devoted to the instantaneous acoustic heating of a shear-thinningfluid. Apparent viscosity of a shear-thinning fluid depends on the shear rate. Thatfeature distinguishes it from a viscous Newtonian fluid. The special linear combi-nation of conservation equations in the differential form makes it possible to derivedynamic equations governing both the sound and non-wave entropy mode inducedin the field of sound. These...
-
Numerical Simulation of Open Channel Flow between Bridge Piers
PublicationPrzedstawiono dwuwymiarowy model przepływu wody płytkiej, który wykorzystano do symulacji przepływu wody w kanale otwartym w rejonie przekroju mostowego. Równania przepływu rozwiązano metodą objętości skończonych. Wyniki symulacji ruchu wody pomiędzy filarami mostowymi porównano z pomiarami laboratoryjnymi przeprowadzonymi w Laboratorium Hydrauliki i Inżynierii Środowiska politechniki Gdańskiej. Zgodność uzyskanych wyników obliczeń...
-
Liveness measurements using optical flow for biometric person authentication
PublicationAutomatyczne rozpoznawanie twarzy jest jedną z najpopularniejszych technik biometrycznych, jednak nawet najdokładniejsze algorytmy identyfikacji okażą się bezużyteczne, jeśli będzie można je oszukać, np. używając zdjęcia zamiast rzeczywistej osoby. Dlatego też odpowiedni pomiar żywotności jest niezwykle istotny. W pracy zaprezentowano metodę, która jest w stanie rozróżnić pomiędzy sekwencjami wideo pokazującymi żywe osoby oraz...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationFlow boiling and flow condensation are often regarded as two opposite or symetrical phenomena. Their description however with a single correlation has yet to be suggested.In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the buble generetion is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such case...
-
Efficiency of acoustic heating produced in the thermoviscous flow of a fluid with relaxation
PublicationInstantaneous acoustic heating of a fluid with thermodynamic relaxation is the subject of investigation. Among others, viscoelastic biological media described by the Maxwell model of the viscous stress tensor, belong to this type of fluid. The governing equation of acoustic heating is derived by means of the special linear combination of conservation equations in differential form, allowing the reduction of all acoustic terms in...
-
PROPERTIES OF ONE DIMENSIONAL OPEN-CHANNEL STEADY FLOW EQUATIONS
PublicationIn this paper properties of discrete forms of one dimensional steady gradually varied flow equations are discussed. Such forms of flow equations are obtained as a result of approximation of their differential forms, which is required to solve them numerically. For such purpose explicit or implicit numerical approximation schemes for ordinary differential equations can be applied. It turns out that dependently on the chosen approximation...
-
Analysis of latency between quotations and capital flow in capital markets.
PublicationThe aim of this paper is to prove that the derivative of the log of capital flow understood as price times volume advances the derivative of log of the price. A certain concept of signal processing using linear filtering has been proposed to conduct the research.