displaying 1000 best results Help
Search results for: MULTIPHASE FLOWS
-
Acoustic Heating Produced in the Thermoviscous Flow of a Shear-Thinning Fluid
PublicationThis study is devoted to the instantaneous acoustic heating of a shear-thinningfluid. Apparent viscosity of a shear-thinning fluid depends on the shear rate. Thatfeature distinguishes it from a viscous Newtonian fluid. The special linear combi-nation of conservation equations in the differential form makes it possible to derivedynamic equations governing both the sound and non-wave entropy mode inducedin the field of sound. These...
-
Numerical Simulation of Open Channel Flow between Bridge Piers
PublicationPrzedstawiono dwuwymiarowy model przepływu wody płytkiej, który wykorzystano do symulacji przepływu wody w kanale otwartym w rejonie przekroju mostowego. Równania przepływu rozwiązano metodą objętości skończonych. Wyniki symulacji ruchu wody pomiędzy filarami mostowymi porównano z pomiarami laboratoryjnymi przeprowadzonymi w Laboratorium Hydrauliki i Inżynierii Środowiska politechniki Gdańskiej. Zgodność uzyskanych wyników obliczeń...
-
Liveness measurements using optical flow for biometric person authentication
PublicationAutomatyczne rozpoznawanie twarzy jest jedną z najpopularniejszych technik biometrycznych, jednak nawet najdokładniejsze algorytmy identyfikacji okażą się bezużyteczne, jeśli będzie można je oszukać, np. używając zdjęcia zamiast rzeczywistej osoby. Dlatego też odpowiedni pomiar żywotności jest niezwykle istotny. W pracy zaprezentowano metodę, która jest w stanie rozróżnić pomiędzy sekwencjami wideo pokazującymi żywe osoby oraz...
-
Selected studies of flow maldistribution in a minichannel plate heat exchanger
PublicationAnalysis of the state of-the-art in research of minichannel heat exchangers, especially on the topic of flow maldistribution in multiple channels, has been accomplished. Studies on minichannel plate heat exchanger with 51 parallel minichannels with four hydraulic diameters, i.e., 461 μm, 574 μm, 667 μm, and 750 μm have been presented. Flow at the instance of filling the microchannel with water at low flow rates has been visualized. The...
-
Estimating the uncertainty of the liquid mass flow using the orifice plate
PublicationThe article presents estimation of measurement uncertainty of a liquid mass flow using the orifice plate. This subject is essential because of the widespread use of this type of flow meters, which renders not only the quantitative estimation but also qualitative results of this type so those measurements are important. To achieve this goal, the authors of the paper propose to use the theory of uncertainty. The article shows the...
-
Numerical Study of Turbulent Flow and Heat Transfer of Nanofluids in Pipes
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (Reynolds number between 6000 and 12000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Reduction of Computational Complexity in Simulations of the Flow Process in Transmission Pipelines
PublicationThe paper addresses the problem of computational efficiency of the pipe-flow model used in leak detection and identification systems. Analysis of the model brings attention to its specific structure, where all matrices are sparse. With certain rearrangements, the model can be reduced to a set of equations with tridiagonal matrices. Such equations can be solved using the Thomas algorithm. This method provides almost the same values...
-
Pressure drop of HFE7000 and HFE7100 during flow condensation in minichannels
PublicationAttention is focused on the issues of flow resistance and pressure drop of perspective refrigeration fluids during condensation in the two-phase flow in minichannels. The case of the flow through a cylindrical single channel of 2.3 mm inner diameter was carefully analyzed. Pressure drop tests have been performed in diabatic flow conditions. The effect of heat flux, mass flux, vapour quality and saturation temperature on the two-phase...
-
Uncertainty of the liquid mass flow measurement using the orifice plate
PublicationThe article presents an estimation of measurement uncertainty of a liquid mass flow using the orifice plate. This subject is essential because of the widespread use of this type of flow meters. Not only the quantitative estimation but also the qualitative results of those measurements are important. To achieve these results the authors of the paper propose to use the theory of uncertainty. The article shows the analysis of the...
-
Numerical study of turbulent flow and heat transfer of nanofluids in pipes
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (6 000 < Re < 12 000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data of Vajjha et al. [1]. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
On various modelling approaches to real-time visualisation of blood flow
PublicationThis paper reviews various modelling approaches to real-time visualisation of blood flow. These include classic, macroscale approach based on the momentum conservation equation together with a proper constitutive equation. Moreover, modern micro- and mesoscale approaches, such as molecular dynamics and dissipative particle dynamics, are discussed. Advantages and disadvantages of the discussed methods are highlighted with particular...
-
Analysis of unsteady flow forces on the thermowell of steam temperature sensor
PublicationIn this paper, 3D numerical analysis of unsteady flow forces acting on the measuring sheath of steam temperature is presented. According to that purpose, the CFD (Computation Fluid Dynamic [1]) approach has been used. The nonstationary of fluid acting on the measuring sheath such as: Strouhal frequency, amplitude of pressure, structure of vortex, peak of pressure, field of pressure, field of velocity etc. are studied analytically...
-
Approximate models and parameter analysis of the flow process in transmission pipelines
Publicationthe paper deals with the problem of early leak detection in transmission pipelines. First we present the derivation of state-space equations of the flow process in the pipelines. This description is then aggregated in order to obtain a principal model. Next, the problem of process model parameterization is addressed, taking into account the maximization of a model stability margin. The location of the maximum is determined using...
-
Analysis of radiometric signal in sedimentating suspension flow in open channel
PublicationThe article discusses issues related to the estimation of the sedimentating solid particles average flow velocity in an open channel using radiometric methods. Due to the composition of the compound, which formed water and diatomite, received data have a very weak signal to noise ratio. In the process analysis the known determining of the solid phase transportation time delay the classical cross-correlation function is the most...
-
Flow of liquid in flat gaps of the satellite motor working mechanism
PublicationThe article describes the methodology and results of investigations of the flow of oil and HFA-E emulsion in flat gaps of the working mechanism of a satellite motor. The flow of liquid in those gaps is turbulent and not fully developed. The article presents two methods of modelling this flow. Method I makes use of the Darcy-Weisbach formula, while Method II bases on the assumption that in the variable-length gaps the flow is turbulent...
-
Recent progress in experimental studies of electrohydrodynamic flow in electrostatic precipitators
PublicationMany experimental, theoretical and numerical works were devoted to the electrohydrodynamic (EHD) flow generated in electrostatic precipitators (EPSs). The generally accepted conclusion from these studies is that the EHD flow plays an important role in the particle collection in ESPs. However, despite of the recent fast progress in numerical simulation and experimental techniques used in the ESPs studies many problems related to...
-
PROPERTIES OF ONE DIMENSIONAL OPEN-CHANNEL STEADY FLOW EQUATIONS
PublicationIn this paper properties of discrete forms of one dimensional steady gradually varied flow equations are discussed. Such forms of flow equations are obtained as a result of approximation of their differential forms, which is required to solve them numerically. For such purpose explicit or implicit numerical approximation schemes for ordinary differential equations can be applied. It turns out that dependently on the chosen approximation...
-
Analysis of latency between quotations and capital flow in capital markets.
PublicationThe aim of this paper is to prove that the derivative of the log of capital flow understood as price times volume advances the derivative of log of the price. A certain concept of signal processing using linear filtering has been proposed to conduct the research.
-
Numerical simulation of cold flow and combustion in a swirl stabilized combustor
PublicationA numerical simulation model was developed to investigate the cold flow and combustion using Ansys FLUENT 2021R1. The governing equations were solved using the pressure-based method, and pressure–velocity coupling was performed using the SIMPLE method. To model the turbulent process, the RSM model was used. Non-premixed model is chosen to solve the chemical kinetics between fuel and oxigen. Radiation heat transfer was calculated...
-
Elektrochemiczne magazyny energii - baterie przepływowe typu "redox flow"
PublicationRozwój i wzrost udziału energii odnawialnej, ze względu na kurczące się zasoby konwencjonalnych źródeł energii i ochronę środowiska, jest możliwy tylko dzięki współpracującym z nimi odpowiednim stacjonarnym magazynom energii. Technologia baterii przepływowych (ang. redox flow batteries, RFB) pozwala świetnie zaspokoić tego typu potrzeby ze względu na: (i) wyjątkowo dużą skalowalność układów; (ii) niezależny dobór mocy i pojemności...
-
Simplified Numerical Model for Transient Flow of Slurries at Low Concentration
PublicationRapid transients are particularly dangerous in industrial hydro-transport systems, where solid-liquid mixtures are transported via long pressure pipelines. A mathematical description of such flow is difficult due to the complexity of phenomena and difficulties in determining parameters. The main aim of the study was to examine the influence of the simplified mixture density and wave celerity description on satisfactory reproduction...
-
Nonlinear Interaction of Magnetoacoustic Modes in a Quasi-Isentropic Plasma Flow
PublicationThe nonlinear interaction of magnetoacoustic waves in a plasma is analytically studied. A plasma is an open system. It is affected by the straight constant equilibrium magnetic flux density forming constant angle with the wave vector which varies from 0 till . The nonlinear instantaneous equation which describes excitation of secondary wave modes in the field of intense magnetoacoustic perturbations is derived by use of projecting....
-
The equivariant spectral flow and bifurcation of periodic solutions of Hamiltonian systems
PublicationWe define a spectral flow for paths of selfadjoint Fredholm operators that are equivariant under the orthogonal action of a compact Lie group as an element of the representation ring of the latter. This G-equivariant spectral flow shares all common properties of the integer valued classical spectral flow, and it can be non-trivial even if the classical spectral flow vanishes. Our main theorem uses the G-equivariant spectral flow...
-
A numerical and experimental analysis of multi-hole orifice in turbulent flow
PublicationIn this research study, the comprehensive metrological analysis is investigated for a 4-hole orifice with module m = 0.25 installed in the pipeline with an internal diameter of 50 mm. A detailed numerical simulation was performed for the turbulence models: k-ε-realizable and k-ω-BSL. The novelties of the research include model validation by comparing the results of numerical studies with the experiment conducted in the area of...
-
Turbulence models impact on the flow and thermal analyses of jet impingement
PublicationAccurate numerical reconstruction of heat and mass transfer processes in particular applications, such a jet impingement, is difficult to obtain even with the use of modern computational methods. In the proposed paper, the flow and thermal phenomena occurring during single minijet impingement on the flat, concave and convex, heated surfaces were considered. Problem of impingement on non-flat surface, still not common and purely...
-
Analysis and interpretation of radiometric signals in a liquid-gas bubble flow
PublicationThe article presents the analysis of signals from a radiometric system consisting of two scintillation probes and two gamma radiation sealed sources. Calculations and interpretation were carried out for the bubble flow of the water-air mixture in the horizontal pipeline. The analysis of the obtained signals was done in time and frequency domain. In the frequency domain, a range of usable frequencies was identified, which were associated...
-
Simplified unsteady flow routing models for flood operating systems
PublicationW pracy omówiono właściwości modeli uproszczonych transformacji przepływów nieustalonych z punktu widzenia możliwości zastosowania do sterowania falą powodziową.
-
Examination of the effect of altering model complexity on representing groundwater flow
PublicationW artykule przedstawiono wyniki badań na dokładnością modeli numerycznych przepływu wód podziemnych. Analizowano wpływ upraszczania struktury przestrzennej modelu na wyniki obliczeń.
-
Electrical capacitance tomography for studying the flow of friable materials in silos.
PublicationArtykuł opisuje możliwość aplikacji tomografii do pomiarów przepływu materiałów sypkich w silosach
-
Horizontal flow boiling of refrigerants inside porous coated tube.
PublicationPrzedstawiono wyniki badań przejmowania ciepła i spadku ciśnienia podczas wrzenia czynników chłodniczych R22, R134a i R407C w poziomej rurce z wewnętrzną powłoką porowatą.
-
Application of time-frequency methods for analysis of dynamic silo flow
PublicationW artykule przedstawiono możliwość stosowania metod czasowo-częstotliwościowych w analizie dynamicznego przepływu materiału sypkiego w silosie. W pracy omówiono wyniki FT (Fourier Transform), STFT (Short Time Fourier Transform) oraz WT (Wavelet Transform)
-
The numerical simulation of two-dimensional vertical incompressible viscous flow
PublicationW artykule przedstawiono numeryczne symulacje płaskiego pionowego przepływu nieściśliwej cieczy lepkiej ze swobodną powierzchnią. Zastosowano model bazujący na rozwiązaniu równań Naviera-Stokesa metodą "ciśnień" (SIMPLE). Przy takim podejściu otrzymano dywergencję równań Naviera-Stokesa oraz równanie Poissona na ciśnienie. W rozwiązaniu zastosowano schemat Laxa-Wendroffa z przesuniętą siatką Eulera. Takie podejście zapewnia dokładność...
-
The contribution of blood-flow-induced conductivity changes to measured impedance
PublicationW pracy rozwazane sa zmiany przewodnosci zachodzace w anizotropowym osrodku i ich wplyw na mierzona rezystancje. Uzyskano to za pomoca rozszerzenia wzoru Geselowizta na przypadki anizotropowe. Wykazano, ze tylko te skladowe zmian przewodnosci wplywaja na mierzona rezystancje, dla ktorych odpowiadajacy im skladnik pola eklektrycznego byl niezerowy.Wyniki te zastosowanu do zmian rezystywnosci wywolanych zmiananmi przewodnosci plynacej...
-
Experimental and numerical analysis of streamwise vortex generator for subsonic flow
PublicationW pracy przedstawiono porównanie wyników obliczeń numerycznych dwoma kodami (FLUENT i SPARC) na tle badań eksperymentalnych generatora wirów wzdłużnych. Przedstawiono wyniki dla liczb Macha przepływu głównego 0.3 i 0.8. Porównano ciśnienie całkowite w dwóch przekrojach za otworem przez który realizowany jest wydmuch. Przedstawiono strukturę wiru wzdłużnego uzyskaną dla obu programów. Średnica otworu jetu jest równa 1mm, co odpowiada...
-
Experimental and theoretical investigations of silo music during granular flow
PublicationPraca dotyczy analizy efektów dynamicznych w silosach podczas przeływu materiałów sypkich.
-
Numerical simulations of granular material flow in silos with and without insert
PublicationArtykuł omawia wyniki naporu materiału sypkiego podczas przepływu w silosach z i bez wkładek. Obliczenia wykonano wykorzystując sformułowanie ale na bazie prawa sprężysto-plastycznego według druckera-pragera. Zbadano wpływ kształtu i położenia wkładki na wielkość naporu i rodzaj przepływu.
-
Confined granular flow in silos with inserts - full-scale experiments
PublicationArtykuł omawia wyniki doświadczalne przepływów silosowych w silosach w naturalnej skali ze wstawkami. Podczas doświadczeń pomierzono przemieszczenia oraz napór na ściany. Zastosowano różne typy wstawek położone na różnej wysokości. Wyniki badań doświadczalnych porównano z przepływami bez wstawek.
-
Experimental and theoretical studies of resonance effects during silo flow.
PublicationPrzedstawiono badania nad rezonansowymi efektami dynamicznymi podczas przepływów silosowych. Wpływ rezonansu na wielkość naporu był analizowany przy pomocy badań doświadczalnych i obliczeń MES na bazie prawa mikropolarnego sprężysto-plastycznego. Doświadczenia wykonano w silosie o przekroju okrągłym i prostokątnym. Zaproponowano efektywną metodę redukcji efektów dynamicznych.
-
Numerical modeling of shear localizations during granular flow in silos.
PublicationW artykule przedstawiono wyniki numerycznej analizy MES dotyczącej przepływów materiałów sypkich w silosach. Omówiono różne metody opisu lokalizacji odkształceń stycznych wewnątrz materiałów. Wyniki porónano z wynikami doświadczalnymi.
-
Simulations of flow patterns in silos with a cellular automaton - part 2
PublicationW artykule przedstawiono wyniki symulacji przepływów silosowych przy zastosowaniu zaawansowanego aparatu komórkowego, w którym uwzględniono kolizje cząstek i dysypację energii. Obliczenia wykonano dla przepływu masowego i kominowego.
-
Analytical model with non-adiabatic effects for pressure drop and heat transfer during boiling and condensation flows in conventional channels and minichannels
PublicationIn the paper a method developed earlier by authors is applied to calculations of pressure drop and heat transfer coefficient for boiling flow and condensation flow with account of non- adiabatic effects for some recent data collected from literature. The first effect, the modification of interface shear stresses in annular flow pattern is considered through incorporation of the so called "blowing parameter". The mechanism of...
-
Possibilities of radioisotope measuring in control of an unstable solid particles hydrotransport
PublicationThe paper presents γ-radiation proposal to control a multiphase flow, independently from circumstances. So this method may be applied even in compound industrial or environmental processes. Moreover in many cases, it is the only method for applications for dense mixture containing coarse angular grains. The constructed equipment allows continuous measurement of density as well as solid phase for both concentration and average velocity....
-
Vident-synth: a synthetic intra-oral video dataset for optical flow estimation
Open Research DataWe introduce Vident-synth, a large dataset of synthetic dental videos with corresponding ground truth forward and backward optical flows and occlusion masks. It can be used for:
-
Flow cytometric sorting and analysis of human epidermal stem cell candidates
Publication -
Interline power flow controller - properties and control strategy in dynamic states
Publication -
Selected thermal and flow issues in a reversed thermosiphon with a steam liquid lifter
Publication -
Isotropic damage in viscoplastic flow conditions, fem applications with practical examples
PublicationW pracy omówiono niektóre zagadnienia zniszczenia w warunkach płynięcia lepkoplastycznego. Podano podstawowe prawa konstytutywne jakie mogą tu być zastosowane oraz sposoby identyfikacji parametrów materiałowych. Pokazano przykład zastosowania.
-
Comparison of cadmium adsorption process on barley straw in batch and flow reactors
Publication -
Cash Flow Management in Small and Medium Enterprises in Times of Economic Uncertainty
Publication -
Recognition of two-phase flow patterns with the use of dynamic image analysis
Publication