displaying 1000 best results Help
Search results for: CHITOSAN HYDROGEL
-
Bioconversion of waste materials to hydrogen via dark fermentation using Enterobacter aerogenes
PublicationHydrogen can be obtained via dark fermentation with the use of anaerobic Enterobacter aerogenes. The efficiency of hydrogen production by fermentation techniques is strongly dependent on the con-ditions used i.e. the pH range, temperature, composition of fermentation broths, oxygen content, or even the presence of substances with potentially inhibitory effects on the microbiological culture [1-4]. The paper describes the study...
-
Bi-based halide perovskites: Stability and opportunities in the photocatalytic approach for hydrogen evolution
PublicationIn this study, we successfully prepared Bi-based single perovskites of the A3Bi2I9 type (A = Cs, Rb, MA, FA), and, for the first time, attempted to experimentally obtain double perovskites Cs2B’BiI6 type (B′ = Ag, Au, In, Cu). Despite the premises available in theoretical studies, our research has proven the impossibility of the existence of double perovskites of this type. Nevertheless, both types of obtained materials were subjected...
-
DEVELOPMENT OF HYDROGEL CAPSULES FOR USE IN DUAL-PHASE TOPICAL PREPARATIONS CONTAINING DIHYDROXYACETONE AND AMINO ACIDS – PRELIMINARY RESULTS
Publication -
In vivo evaluation of the antipsoriatic effect of hydrogel with lavandin essential oil and its main components after topical application
Publication -
Expermental investigation on adsorption of methylene blue dye from waste water using corncob cellulose-based hydrogel
PublicationHydrogel from corncob cellulose was synthesized in this investigation. The synthesized Hydrogel was characterized by SEM, XRD, and FTIR instruments. As the results indicate the synthesized hydrogel has required and important features, these suggest the suitability of hydrogel for the adsorption of methylene blue dye (MBD). Three important process variables (dosage, contact time, and initial concentration) with three levels were...
-
The effect of zinc oxide concentration on dry matter content of chitosan gels in carbonic acid.
Open Research DataThe dataset contains results determining the effect of zinc oxide addition at different concentrations on the dry matter content of chitosan gels in carbonic acid after a specified time. Zinc oxide at concentrations of 0.5 and 1% was added as a powder to a 1% solution of chitosan in carbonic acid and then homogenized. Differences were observed in the...
-
A novel method for drop in drop edible oils encapsulation with chitosan using a coaxial technique
Open Research DataThe dataset present a novel one step method for oil encapsulation. In this coaxial system the oil constitutes the core of the capsule, while the chitosan solution is the polymer shell surrounding the core to provide separation of the core from the external environment. In comparison to other encapsulation methods, the presented technique is much simpler...
-
Could spray-dried microbeads with chitosan glutamate be considered as promising vaginal microbicide carriers? The effect of process variables on the in vitro functional and physicochemical characteristics
Publication -
The combined effect of moderate pressure and chitosan on Escherichia coli and Staphylococcus aureus cells suspended in a buffer and on natural microflora of apple juice and minced pork
PublicationW pracy określono przeżywalność bakterii Escherichia coli i Staphylococcus aureus oraz naturalnej mikroflory soku jabłkowego i rozdrobnionego mięsa świńskiego po działaniu ciśnienia 193 MPa w temp. -20 C w obecności chitozanu. Stwierdzono, że traktowanie mikroorganizmów ciśnieniem w obecności chitozanu pozwala na przedłużenie trwałości badanych produktów przechowywanych w temperaturze chłodniczej o około 8-10 dni.
-
Badania bioaktywności z wykorzystaniem komórek kościotwórczych na tytanie pokrytym chitozanem = Bioactivity studies using osteogenic cells on titanium coated with chitosan
PublicationChitosan is a natural polymer from the group of polysaccharides, which has found wide application in biomedical applications to induce bioactivity of implant. The studies described were carried out test imposition of chitosan membranes with varying degrees of deacetylation on the surface of titanium, and then check the bioactivity of the material in vitro, using osteogenic cells MC3T3-E1. Titanium surface before imposition of...
-
Double-Layered Films Based on Furcellaran, Chitosan, and Gelatin Hydrolysates Enriched with AgNPs in Yerba Mate Extract, Montmorillonite, and Curcumin with Rosemary Essential Oil
Publication -
Performance tuning of chitosan-based membranes by protonated 2-Pyrrolidone-5-carboxylic acid-sulfolane DES for effective water/ethanol separation by pervaporation
PublicationToday, the applicability of deep eutectic solvents (DES) in various fields, including membrane science and technology, is extensively investigated. In pioneering works, we have implemented different DES as a component of chitosan (CS)-based flat membranes for pervaporation (PV) separation. Herein, we present a new protonated (by sulphuric acid) 2-Pyrrolidone-5-carboxylic acid: sulfolane DES, as a green additive for its chemical...
-
Photocatalytic mineralisation of humic acids using TiO2 modified by tungsten dioxide/ hydrogen peroxide
Publication -
Pd nanoparticles with tunable diameter deposited on carbon nanotubes with enhanced hydrogen storage capacity
Publication -
Crystal structure, hydrogen bonds, and lattice dynamics in kanemite from first-principles calculations
Publication -
In situ deposition of Pd nanoparticles with controllable diameters in hollow carbon spheres for hydrogen storage
Publication -
Pressure and temperature effect on hypergolic ignition delay of triglyme-based fuel with hydrogen peroxide
Publication -
Experimental determination of critical conditions for hydrogen-air detonation propagation in partially confined geometry
Publication -
Aluminum-TiO2 NPs Composites as Non-precious Catalysts for Efficient Electrochemical Generation of Hydrogen
PublicationIn this paper, we demonstrated, for the first time, aluminum titania nanoparticle (Al-TiO2 NP) composites with variable amounts of TiO2 NPs as nonprecious active catalysts for the electrochemical generation of H2. These materials were synthesized by mixing desired amounts of hydrogen titanate nanotubes (TNTs), fabricated here by a cost-effective approach at moderate hydrothermal conditions, with aluminum powder (purity 99.7%; size...
-
Conversion of Biomass and Municipal Wastes into Syngas and Hydrogen using Highly Preheated Agent (HTAG)
PublicationGasification is considered to be one of the most promising energy recovery technologies for the widespread utilization of biomass and wastes. During this process raw feedstock is converted into a combustible gas, which can then be burnt to produce thermal energy, or to run engines for mechanical or electrical power. The studies of biomass gasification demonstrate it as a friendly alternative to fossil fuels as one of renewable...
-
Hydrogen Production from Energy Poplar Preceded by MEA Pre-Treatment and Enzymatic Hydrolysis
PublicationThe need to pre-treat lignocellulosic biomass prior to dark fermentation results primarily from the composition of lignocellulose because lignin hinders the processing of hard wood towards useful products. Hence, in this work a two-step approach for the pre-treatment of energy poplar, including alkaline pre-treatment and enzymatic saccharification followed by fermentation has been studied. Monoethanolamine (MEA) was used as the...
-
Low-energy electron scattering from molecular hydrogen: Excitation of the X1Σg+ to b3Σu+ transition
PublicationWe present time-of-flight differential cross-section measurements and convergent close-coupling calculations of differential cross sections for the electron-impact excitation of the X 1 g + → b 3 u + transition in molecular hydrogen. A part of this work was recently published [M. Zawadzki et al., Phys. Rev. A 97, 050702(R) (2018)]. In this work, agreement between theory and experiment is excellent overall, and marks a transition...
-
Effect of Pd loading on hydrogen storage properties of disordered mesoporous hollow carbon spheres
Publication -
PANI/NaTaO3 composite photocatalyst for enhanced hydrogen generation under UV light irradiation
Publication -
Oxidized SWCNT and MWCNT as co-catalysts of polymeric carbon nitride for photocatalytic hydrogen evolution
Publication -
Enhancement of photocatalytic hydrogen evolution with catalysts based on carbonized MOF-5 and g-C3N4
Publication -
Effect of shielded electrode wet welding conditions on diffusible hydrogen content in deposited metal
PublicationWet welding is the most popular method of joining in water enviroment. During underwater welding, the weldability of steel is limited by the higher cooling rates and hydrogen content in weld metal. Article presents results of preliminary tests on the effects of wet welding conditions on diffusible hydrogen amount. Seven parameters were optimized using a Plackett-Burman plan to get the most relevant variables. These parameters were:...
-
High temperature air/steam gasification of biomass in view of hydrogen rich gas production.
PublicationArtykuł przedstawia opis nowej i zaawansowanej metody konwersji termochemicznej biomasy i miejskich odpadów stałych w paliwo gazowe, bogate w wodór. W porównaniu z tradycyjnym procesem gazyfikacji, w metodzie tej wykorzystuje się powietrze/parę wodną przegrzane do wysokiej temperatury (powyżej 1300 st. C). Przegrzanie powietrza lub pary wodnej odbywa się z zastosowaniem ceramicznego przegrzewacza wysokotemperaturowego. W celu...
-
Hydrogen-enhanced stress corrosion cracking and corrosion fatigue of HSLA steels in sea-water
PublicationPrzedstawiono ocenę podatności stali o wysokiej wytrzymałości na naprężeniowe pękanie korozyjne i zmęczenie korozyjne wspomagane przez wodór. Wykonano próby powolnego rozciągania i zmęczenia niskoczęstotliwościowego na stalach 17HMBVA i 14HNMBCu oraz ich złączach spawanych, w środowisku wody morskiej, przy polaryzacji katodowej. Zamieszczono wyniki badań elektrochemicznych oraz przełomów na skaningowym mikroskopie elektronowym.
-
Hydrogen rich gas production from high temperature air/steam gasification of biomass
PublicationW pracy przedstawiono nowoczesną technikę konwersji biomasy oraz stałych odpadów komunalnych w celu produkcji paliwa gazowego bogatego w wodór. Opisany proces gazyfikacji przebiega w wysokiej temperaturze przy obniżonej koncentracji tlenu i udziale pary wodnej. Dzięki temu możliwa jest produkcja gazów palnych, w szczególności H2, który można wykorzystać do produkcji energii elektrycznej i cieplnej.
-
Review of hydrogen production technologies for automotive sector – thermodynamic analysis of energy and exergy losses
PublicationFew recent years has shown that hydrogen technology has a good chance to replace petroleum technology in automotive sector. However, hydrogen in pure form practically does not occur on Earth. That is why H2 form is used only as an energy carrier and it must be produced using another source of energy form water or hydrocarbon fuels. In this paper short overview of hydrogen production technology has been presented, with energy and...
-
The effect of pre-hydrogen charging on corrosion behaviour of superduplex stainless steel welded joints
PublicationThe paper presents results of research undertaken to determine the influence of hydrogen on passivity and corrosion resistance of 2507 super duplex stainless steel welded joints. Butt welded joints were made with low heat input using flux corded arc welding (FCAW) method. Coupons of 5.0 x 5.0 mm were cut from the welded joints containing weld metal (WM), heat affected zone (HAZ) and parent metal (PM). Hydrogen was introduced...
-
Niszczenie wodorowe stali o podwyższonej wytrzymałości = Hydrogen degradation of high-strength steels.
PublicationW artykule przedstawiono niszczenie wodorowe stali 18G2A i jej symulowanej strefy wpływu ciepła (SWC). Jako parametry niszczenia wodorowego wybrano względne wartości energii zniszczenia, czasu do pęknięcia, wydłużenia, przewężenia i wytrzymałości na rozciąganie. Parametry te wyznaczono w próbie odkształcania z małą prędkością na próbkach gładkich, okrągłych. Stwierdzono, że stal 18G2A w środowisku kwaśnym (0,1 N H2SO4) podczas...
-
Effect of wet Hydrogen Sulfide on Carbon Steels Degradation in Refinery Based on Case Study
PublicationMaterial degradation caused by wet hydrogen sulfide (Wet H2S) is one of the major issues in refineries. Carbon steel is the main construction material used in refineries and is subjected not only to thickness loss but the hydrogen is the major concern. H2S leads to high atomic hydrogen penetration in steel which causes degradation in the form of blistering and/or cracking (HIC/SOHIC) and stress cracking in the area of welds and...
-
Influence of conductive carbon and MnCo2O4 on morphological and electrical properties of hydrogels for electrochemical energy conversion
PublicationIn this work, a strategy for one-stage synthesis of polymer composites based on PNIPAAm hydrogel was presented. Both conductive particles in the form of conductive carbon black (cCB) and MnCo2O4 (MCO) spinel particles were suspended in the three-dimensional structure of the hydrogel. The MCO particles in the resulting hydrogel composite acted as an electrocatalyst in the oxygen evolution reaction. Morphological studies confirmed...
-
Preliminary investigations of effect of conditions of FCAW process on diffusible hydrogen content in deposited metal
PublicationOne of the types of hydrogen degradation of steel welded joints is cold cracking. The direct cause of the formation of cold cracks is simultaneous presence of hydrogen, residual stresses and brittle structure. The way of preventing the occurring of degradation is to eliminate at least one of these factors. Practice has shown that the best solution is to control the amount of hydrogen in deposited metal. In this paper the state...
-
Diffusible hydrogen management in underwater wet self-shielded flux cored arc welding
PublicationThis article reports the effect of underwater wet welding parameters and conditions on the diffusible hydrogen content in deposited metal for welding with a self-shielded flux cored wire. The diffusible hydrogen content in deposited metal was determined using the glycerin method according to the Plackett-Burman design determining the significance of the effect of the stick out length, welding current, arc voltage, travel speed...
-
Nanosize effect of clay mineral nanoparticles on the drug diffusion processes in polyurethane nanocomposite hydrogels
PublicationStudies of swelling and release of naproxen sodium (NAP) solution by polyurethane nanocomposite hydrogels containing Cloisite® 30B (organically modified montmorillonite (OMMT)) have been performed. Polyurethane nanocomposite hydrogels are hybrid, nontoxic biomaterials with unique swelling and release properties in comparison with unmodified hydrogels. These features enable to use nanocomposite hydrogels as a modern wound dressing....
-
Bismuth-Doped Nano Zerovalent Iron: A Novel Catalyst for Chloramphenicol Degradation and Hydrogen Production
PublicationIn this study, we showed that doping bismuth (Bi) at the surface of Fe0 (Bi/Fe0, bimetallic iron system)—synthesized by a simple borohydride reduction method—can considerably accelerate the reductive degradation of chloramphenicol (CHP). At a reaction time of 12 min, 62, 68, 74, 95, and 82% degradation of CHP was achieved with Fe0, Bi/Fe0-1 [1% (w/w) of Bi], Bi/Fe0-3 [3% (w/w) of Bi], Bi/Fe0-5 [5% (w/w) of Bi], and Bi/Fe0-8 [8%...
-
Kinetic characterization of hydrogen sulfide inhibition of suspended anammox biomass from a membrane bioreactor
PublicationThe inhibition effects of hydrogen sulfide (H2S) on anammox-enriched biomass from a laboratory membrane reactor were analyzed in a series of batch respirometric experiments. The determined half maximal inhibitory concentration (IC50) was 4.67 mg H2S-S L−1 at the constant pH = 7.0 and the total sulfide concentration varying between 1 and 15 mg TS-S L−1. In another test, the IC50 was found to be 4.25 mg H2S-S L−1 under a constant...
-
Laboratory bioreactor with pH control system for investigations of hydrogen production in the dark fermentation process
PublicationThe work presents the construction of a low-cost research bioreactor equipped with a pH control sys-tem. The developed bioreactor was applied for hydrogen production in the dark fermentation process using Enterobacter aerogenes ATCC 13048. Presented paper compares the results obtained during the process without and with pH regulation for different feed materials: glucose, energetic poplar hydro-lysates, acid whey and glycerol....
-
Effect of the welding environment and storage time of electrodes on the diffusible hydrogen content in deposited metal
PublicationIn the study the glycerin displacement method was used for determination of diffusible hydrogen content in deposited metal. Specimens were welded in the air and in the water with covered rutile electrodes. The first part of the specimens was made immediately after opening the package of the electrodes. The electrodes were then stored in opened packages in laboratory conditions that allowed for contact with the air for three years....
-
Mathematical modeling of hydrogen production performance in thermocatalytic reactor based on the intermetallic phase of Ni3Al
PublicationThe main goal of the following work is to adjust mathematical modelling for mass transfer, to specific conditions resulting from presence of chemical surface reactions in the flow of the mixture consisting of helium and methanol. The thermocatalytic devices used for decomposition of organic compounds incorporate microchannels coupled at the ends and heated to 500 oC at the walls regions. The results of the experiment were compared...
-
TG-hydroxyl groups in TiO2-P25
Open Research DataTG analyses were performed for powdered TiO2 - commercial P25 sample, which was heat-treated from room temperature to 500 C in the nitrogen atmosphere. Mass loss at lower temperature such as 120 C was related to the physisorbed water, and that one occurring at 500 C to the chemisorbed hydroxyl groups.
-
Raman data of deuterium and hydrogen grown boron-doped diamond
Open Research DataRaman spectra were recorded at room temperature using a micro-Raman spectrometer (Invia, Renishaw) equipped with an edge filter with different excitation wavelengths and lasers: UV λ = 325 nm (HeCd), blue λ = 488 nm (Ar+), green λ = 514 nm (Ar+), and IR λ = 785 nm (IR diode) and 50× microscope objective. To avoid sample heating, the radiation power...
-
The effect of changes in the concentration of hydroxypropylcellulose on the rheological stability of pectin hydrogels.
Open Research DataThe rheological characteristics of the pectin hydrogel modified by hydroxypropylcellulose (added in a concetration range from 0.1 to 0.55% m/m) were made on the basis of the viscosity assessment using a Brookfield viscometer with an LV SC4 - 25 spindle and a shear rate of 0,22 s-1 in the temperature range 19-96 ° C.The data allowed selection of optimal...
-
XPS data of deuterium and hydrogen grown boron-doped diamond
Open Research DataThe high-resolution C1s X-ray absorption spectra of BDD@H and BDD@D samples were measured using the facilities of the HE-SGM beamline (HE-SGM) at the BESSY II synchrotron radiation source of Helmholtz–Zentrum Berlin (HZB).[90] The measurements were carried out under ultra-high vacuum conditions: P ≈ 2×10−9 Torr at T = 300 K. The NEXAFS spectra were...
-
Data on hydrogen migration in cation-induced dissociation of furan molecules
Open Research DataThe data include furan luminescence spectra obtained in collisions with H3+ and C+ cations and theoretical spectra of OH and CH radicals published in [1].
-
Determination of changes in viscosity of hydrogel depending on shear rate (1.1 to 55 s-1).
Open Research DataThe rheological characteristics of hydrogel were made on the basis of a viscosity measurement using a Brookfield viscometer, using LV SC4 - 25 spindle and shear rates from 1.1 to 55 s-1.
-
Determination of changes in viscosity of hydrogel depending on shear rate (1.7 to 34 s-1).
Open Research DataThe rheological characteristics of hydrogel were made on the basis of a viscosity measurement using a Brookfield viscometer, using LV SC4 - 27 spindle and shear rates from 1.7 to 34 s-1.