Filters
total: 5293
-
Catalog
- Publications 795 available results
- Journals 16 available results
- Conferences 1 available results
- People 70 available results
- Inventions 18 available results
- Projects 8 available results
- Laboratories 6 available results
- Research Teams 4 available results
- Research Equipment 3 available results
- e-Learning Courses 181 available results
- Events 47 available results
- Open Research Data 4144 available results
displaying 1000 best results Help
Search results for: MMA
-
Dynamics of a linear pneumatic actuator with 50 mm piston diameter and 100 mm stroke subjected only to a mass load of 1530 g
Open Research DataThe aim of the study was to determine the dynamics of a linear pneumatic cylinder subjected only to mass load. An actuator of one of the well known European manufacturers was tested.The experiment were to measure pressure changes in both chambers of the actuator and the position of the piston during stroke and retracting. The test was repeated 11 times....
-
Dynamics of a linear pneumatic actuator with 63 mm piston diameter and 150 mm stroke subjected only to a mass load of 1640 g
Open Research DataThe aim of the study was to determine the dynamics of a linear pneumatic cylinder subjected only to mass load. An actuator of one of the well known European manufacturers was tested.The experiment were to measure pressure changes in both chambers of the actuator and the position of the piston during stroke and retracting. The test was repeated 11 times....
-
Dynamics of a linear pneumatic actuator with 80 mm piston diameter and 100 mm stroke subjected only to a mass load of 1100 g
Open Research DataThe aim of the study was to determine the dynamics of a linear pneumatic cylinder subjected only to mass load. An actuator of one of the well known European manufacturers was tested.The experiment were to measure pressure changes in both chambers of the actuator and the position of the piston during stroke and retracting. The test was repeated 11 times....
-
Dynamics of a linear pneumatic actuator with 80 mm piston diameter and 100 mm stroke subjected only to a mass load of 2570 g
Open Research DataThe aim of the study was to determine the dynamics of a linear pneumatic cylinder subjected only to mass load. An actuator of one of the well known European manufacturers was tested.The experiment were to measure pressure changes in both chambers of the actuator and the position of the piston during stroke and retracting. The test was repeated 11 times....
-
[IMa] Materials technologies - 2023/24
e-Learning Courses{mlang pl} Dyscyplina: inżynieria materiałowa Zajęcia obowiązkowe dla doktorantów I roku Prowadzący: prof. dr hab. inż. Maria Gazda, prof. dr hab. inż. Józef Haponiuk, dr hab. inż. Sebastian Molin, dr hab. inż. Jacek Ryl, dr hab. inż. Robert Bogdanowicz Liczba godzin: 15 Forma zajęć: wykład/seminarium {mlang} {mlang en} Discipline: materials engineering Obligatory course for 1st year PhD students Academic teachers: prof....
-
Synthesis and biological activity of mycophenolic acid-amino acid derivatives
PublicationIn search of new immunosuppressants, mycophenolic acid (MPA) was coupled with amino acid methyl esters followed by hydrolysis to analogs bearing free carboxylic groups. The obtained compunds were tested in vitro as growth inhibitors of lymphoid cell line (Jurkat) and human peripheral blood mononuclear cells (PBMC) from healthy donors. According to obtained results recovering of free carboxylic group increased their activity. Additionally,...
-
Ocena rozkładu namagnesowania wewnątrz płyty magnesowanej elektromagnesem jarzmowym. Zesz. Probl. - Badania Nieniszczące.**2003 nr 8 s. 61-66, 8 rys. bibliogr. 11 poz. Materiały 32 Krajowej Konferencji Badań nieniszczących 32 KKBN. Międzyzdro- je 28-30. X. 2003 r.
PublicationPrzedstawiono wyniki badań rozkładu namagnesowania wewnątrz płyty magnesowa-nej elektromagnesem jarzmowym. Mierzono a) rozkład na powierzchni płyty na-tężenia efektu Barkhausena EB sondą punktową b) natężenie emisji magnetoaku-stycznej EMA. Pętle histerezy natężenia EB oraz EMA ujawniły efekt przesu-nięcia fazowego procesu magnesowania wewnątrz płyty wynikającego z prądówwirowych. Wyniki pomiarów zostały potwierdzone wynikami...
-
Investigation of magnetic and magnetomechanical hysteresis properties of Fe Si alloys with classical and mechanical Barkhausen effects and magnetoaco ustic emission.
PublicationW stopach Fe 3,5% Si o strukturze GO oraz NO badano własności histerezowe za pomocą polowego HBE i mechanicznego MEB efektu Barkhausena oraz emisji magnetoakustycznej EMA. Rozkład naprężeń wewnętrznych został wyznaczony wykorzystując zależność natężenia MEB od naprężeń zewnętrznych (próba pierwszego naprężania). Stwierdzenie MEB oraz EMA o znaczącym naprężeniu dowodzi występowania granic typu 90 deg. Są to granice domen typu...
-
[IMa] Experimental Methods for Materials Characterisation
e-Learning Courses{mlang pl} Dyscyplina: inżynieria materiałowa Zajęcia obowiązkowe dla doktorantów I i II roku Prowadzący: A. Mielewczyk-Gryń, M. Szkodo, B. Bochentyn, J. Ryl Liczba godzin: 30 Forma zajęć: laboratoria {mlang} {mlang en} Discipline: materials engineering Obligatory course for 1-st and 2nd-year PhD students Academic teachers: M. Gazda, A. Lisowska-Oleksiak, A. Mielewczyk-Gryń, R. Bogdanowicz, T. Klimczuk, Ł. Piszczyk,...
-
[NCh, IMa] Properties of novel materials
e-Learning Courses{mlang pl} Dyscyplina: nauki chemiczne, inżynieria materiałowa Zajęcia fakultatywne Prowadzący: prof. dr hab. inż. T. Klimczuk, WFTiMS Liczba godzin: 15 Forma zajęć: wykład {mlang} {mlang en} Discipline: chemical sciences, materials engineering facultative course Academic teacher: prof. dr hab. inż. T. Klimczuk, WFTiMS Total hours of training:15 teaching hours Course type: lecture {mlang}
-
Strain-dependent behaviour of cold recycled material mixtures in cyclic compression tests
PublicationThe purpose of the study is to evaluate strain-dependent behaviour of Cold Recycled Material (CRM) mixtures using three frameworks typically applied for Hot Mix Asphalt (HMA): linear viscoelastic (LVE) limits; non-linearity directions; changes in rheological model parameters. To this aim, the complex modulus of three CRM mixtures with different bitumen-to-cement ratio (0.2, 0.6 and 1.8) was measured in cyclic compression mode,...
-
Agata Kot-Wasik prof. dr hab. inż.
PeopleAgata Kot-Wasik, born in 1964 in Siedlce, graduated in 1988 from the Faculty of Chemistry, Gdańsk University of Technology in Industrial and Technical Analysis. In 1988-1992 she was employed in the Department of Organic Chemistry. In 1990, she completed postgraduate studies "Instrumental techniques in the traces analysis and Environmental Protection" at GUT, and in 1992 began PhD Studies at the Faculty of Chemistry, GUT, which...
-
Underwater Welding of Duplex Stainless Steel
PublicationThe present work was conducted to assess the weldability of duplex stainless steel at underwater conditions. Interest of underwater welding of this steel grade is connected with necessity of preparing welding repair technologies for subsea pipelines widely used in offshore oil and gas industry. The GMA local cavity welding method was used in the investigations. Welded beads were performed underwater at 0.5 m depth and in the air....
-
Eksperymentalne badania rozkładu ciśnienia w uszczelnieniu nadbandażowym stopnia turbinowego.**2002, 127 s. 86 rys. bibliogr. 164 poz. + zał. ma- szyn. Rozprawa doktorska /25.06.2002/ WOiO PG. Promotor: dr hab. inż. K. Kosowski, prof. nadzw. PG.
Publication.
-
Projektowanie opóźniających filtrów cyfrowych FIR metodą iteracji czasowo--częstotliwościowej.**2003, 136 s. 89 rys. 5 tab. bibliogr. 129 poz. ma- szyn. Rozprawa doktorska /11.02.2003/ WETI PG. Promotor: dr hab. inż. Ewa Hermanowicz, prof. PG.
PublicationRozprawa doktorska jest poświęcona projektowaniu filtrów cyfrowych ułamkowo--opóźniających typu FIR. W pracy przedstawiono dwie metody projektowania ta-kich filtrów. Pierwsza z nich jest oparta na zespolonym algorytmie Remeza.Umożliwia ona wydajne numeryczne projektowanie banków filtrów ułamkowo-opóź-niających optymalnych w sensie Czebyszewa. W drugiej metodzie projektowanieodbywa się drogą iteracji czasowo-częstotliwościowej....
-
Molecularly targeted nanoparticles: an emerging tool for evaluation of expression of the receptor for advanced glycation end products in a murine model of peripheral artery disease
PublicationAbstract Background: Molecular imaging with molecularly targeted probes is a powerful tool for studying the spatio-temporal interactions between complex biological processes. The pivotal role of the receptor for advanced glycation end products (RAGE) in numerous pathological processes, aroused the demand for RAGE targeted imaging in various diseases. In the study, we evaluated the use of a diagnostic imaging agent for RAGE quantification...
-
Underwater Local Cavity Welding of S460N Steel
PublicationIn this paper, a comparison of the mechanical properties of high-strength low-alloy S460Nsteel welded joints is presented. The welded joints were made by the gas metal arc welding (GMAW)process in the air environment and water, by the local cavity welding method. Welded joints were testedfollowing the EN ISO 15614-1:2017 standard. After welding, the non-destructive—visual, penetrant,radiographic, and ultrasonic (phased array) tests...
-
Modifications of total synthesis of mycophenolic acid
PublicationThe total synthesis of mycophenolic acid (MPA), a potent immunosuppressant, was modified. The obtained mycophenolic acid was suitable for further preparation of new prospective immunosuppressants with improved therapeutic properties.
-
Robert Janczewski dr hab. inż.
People -
rigid polyurethane foams modified with selected nanofillers
PublicationThe nanofillers: natural montmoryllonite (MMT) - Bentonite, natural MMT modified with a quaternary ammonium salt - Cloisite30B, has been used in rigid polyurethane foams (PUFs). The influence of fillers amounts on processing parameters, physical-mechanical properties (density, water absorption, brittleness and compression strength) and thermal properties (thermal stability, fire behaviours) of such foams has been analysed. The...
-
Effect of high pressure and sub-zero temperature on some gram-negative bacteria.
PublicationCelem pracy było określenie przeżywalności wybranych gramujemnych bakterii na działanie wysokiego ciśnienia i ujemnej temperatury. Traktowanie komórek bakterii ciśnieniem 193 MPa w temperaturze -20C przez 24 godziny, powodowało całkowitą inaktywację bakterii E. coli, P. fluorescens i T. thermophilus. Po działaniu ciśnienia przez krótszy czas występowały różnice we wrażliwości między badanymi szczepami. Najmniej odporny na działanie...
-
Badanie wytrzymałości zaczynu cementowego na ściskanie przeznaczonego do wypełnienia elementów konstrukcyjnych platform wiertniczych.
PublicationPrzedmiotem opracowania było badanie wytrzymałości zaczynu cementowego na ściskanie o wytrzymałości 70-80 MPa przeznaczonego do wypełnienia elementów konstrukcji platform wiertniczych pod wodą.
-
Controlled grafting of vinylic monomers on polyolefins: a robust mathematical modeling approach
PublicationExperimental and mathematical modeling analyses were used for controlling melt free-radical grafting of vinylic monomers on polyolefins and, thereby, reducing the disturbance of undesired cross-linking of polyolefins. Response surface, desirability function, and artificial intelligence methodologies were blended to modeling/optimization of grafting reaction in terms of vinylic monomer content, peroxide initiator concentration,...
-
The influence of moderate pressure and subzero temperature on the shelf life of minced cod, salmon, pork and beef meat
PublicationThe effect of moderate pressure at subzero temperature on natural microflora of minced cod, salmony, pork and beef meat was studied. Pressure of 193 MPa at –20 °C caused reduction of total bacterial count in pork and beef meat by 1.1 and 0.6 log cycles, respectively, and by about 1.5 log cycles in fish meat. Under these conditions the psychrophilic and psychrotophic bacteria were below the detection limit (<10CFU/g of sample) in...
-
Wear Resistance Enhancement of Al6061 Alloy Surface Layer by Laser Dispersed Carbide Powders
PublicationIn this paper, results of the experimental study on improving wear resistance in sliding friction of Al-based alloy are presented. The technique used involves the formation of a metal matrix composite (MMC) in the alloy surface layer by laser dispersion of carbide powders such as WC, TiC and SiC. For WC and TiC MMC surface coatings fabricated under conditions typical for most of the technologically relevant solid-state lasers (wavelength...
-
Formation of chlorinated breakdown products during degradation of sunscreen agent, 2-ethylhexyl-4-methoxycinnamate in the presence of sodium hypochlorite
PublicationIn this study, a new degradation path of sunscreen active ingredient, 2-ethylhexyl-4-methoxycinnamate (EHMC) and 4-methoxycinnamic acid (MCA) in the presence of sodium hypochlorite (NaOCl), was discussed. The reaction products were detected using gas chromatography–mass spectrometry (GC-MS). Since HOCl treatment leads to more polar products than EHMC, application of polar extracting agents, dichloromethane and ethyl acetate/n-hexane...
-
Effect of microwave and convection heating on selected nutrients of human milk
PublicationThe aim of this study was to determine the influence of the microwave heating method (MWH) on selected determinants of the nutritional value of human milk (HM) and compare to the effect exerted by the standard convection heating (CH) method, including holder pasteurization (HoP). It was showed that using MWH under conditions assumed to ensure microbiological safety, changes in the level of the nutrients were not observed. In these...
-
Opinia o nowej technologii planowanej do wdrożenia w ramach inwestycji na którą ma być udzielony kredyt technologiczny: ''Sposób wytwarzania składanych szaf teleinformatycznych o zwiększonej odporności korozyjnej i walorach estetycznych w procesie jednoczesnego kształtowania stelaży modułowych wsporczych''
PublicationOpinię o nowej technologii opracowano dla Banku Gospodarstwa Krajowego na podstawie Ustawy z dnia 30 maja 2008 r. o niektórych formach wspierania działalności innowacyjnej (Dz. U. z 2008 r. Nr 116, poz. 730) z późniejszymi zmianami. Jednostką Naukową wystawiającą Opinię był Wydział Mechaniczny PG. Podmiotem wdrażającym opiniowaną technologię było Przedsiębiorstwo EL-BOX, Krzysztof Kraszewski.
-
Opinia naukowo-techniczna dotycząca nośności pali wierconych fi 1500 mm wykonanych pod podpory wiaduktu C-4 na podstawie badań statycznych. Budowa Północnego Obejścia Krakowa w ciągu Drogi Krajowej nr 94 na odcinku Węzeł Radzikowskiego - Węzeł Modlnica.
PublicationOpinia dotycząca nośności pali wierconych o średnicy 1500 mm wykonanych pod podpory wiaduktu C-4 w ciągu Drogi Krajowej nr 94 na odcinku Węzeł Radzikowskiego - Węzeł Modlnica na podstawie próbnych obciążeń statycznych.
-
Opinia o nowej technologii planowanej do wdrożenia w ramach inwestycji na którą ma być udzielony kredyt technologiczny: ''Sposób wytwarzania drzwi zewnętrznych o podwyższonym wskaźniku przenikalności cieplnej oraz podwyższonej odporności na wilgoć, w tym drzwi z przeszkleniem''
PublicationOpinię o nowej technologii opracowano dla Banku Gospodarstwa Krajowego na podstawie Ustawy z dnia 30 maja 2008 r. o niektórych formach wspierania działalności innowacyjnej (Dz. U. z 2008 r. Nr 116, poz. 730) z późniejszymi zmianami. Jednostką Naukową wystawiającą Opinię był Wydział Mechaniczny PG. Opinia dotyczyła projektu zatytułowanego "Wdrożenie innowacyjnej technologii energooszczędnych zewnętrznych drzwi stalowych". Podmiotem...
-
On the possibility of the application of magnetoacoustic emission intensity measurements for the diagnosis of thick-walled objects in the industrial environment
PublicationArtykuł przedstawia wyniki pomiarów sygnału emisji magnetoakustycznej (EMA) wykonanych na obiektach grubościennych w środowisku przemysłowym oraz omawia możliwe sposoby jego dalszej analizy. Pomimo tego, ze bezpośredni pomiar sygnału EMA nie pozwala na określenie jego natężenia w artykule wykazano, że możliwa jest separacja użytecznego sygnału od szumów tła albo poprzez analogowe filtrowanie sprzętowe albo poprzez cyfrową analizę...
-
Guangcheng Ma Ph.D.
People我是上海财经大学城市与区域科学学院的博士生。 研究方向包括气候变化主题,如绿色经济发展、城市低碳研究、DSGE研究和碳足迹核算。 在硕士和博士学习期间,我认真学习学院安排的各种专业课程,在课堂上积极与老师和同学讨论,并主动与导师交流学习经验。 我利用学校图书馆资源广泛阅读国内外文献,仔细研究研究领域的热点话题和前沿方法。 我学会了如何使用各种统计软件,主要掌握了STATA、MATLAB、Eviews和SPSS等计量软件的使用。 在写作方面,我精通使用LaTeX编译进行学术论文写作和排版。 DSGE模型的推导和政策模拟也有一定的基础。 还能够进行投入产出分析和增值核算、空间测量和ArcGIS应用。 这些测量方法的使用为获得当前的一些结果奠定了基础。 到目前为止,我已经作为第一作者和通讯作者发表在国内外知名期刊上:《中国产业经济学》、《城市》、《能源经济学》、《结构变化与经济动力学》、《清洁生产杂志》、《 《国际企业家精神和管理杂志》和《环境科学前沿》。...
-
Konsultacje (MMM, Robotyka) ACR sem. 4
e-Learning CoursesMateriały do zajęć: Metody Modelowania Matematycznego, Podstawy Robotyki
-
[IMa] Experimental Methods for Materials Characterisation - 2024
e-Learning Courses{mlang pl} Dyscyplina: inżynieria materiałowa Zajęcia obowiązkowe dla doktorantów I i II roku Prowadzący: R. Bogdanowicz, J. Karczewski, T. Klimczuk, S. Molin, M. Strankowski, N. Wójcik, Liczba godzin: 30 Forma zajęć: laboratoria {mlang} {mlang en} Discipline: materials engineering Obligatory course for 1-st and 2nd-year PhD students Teachers: R. Bogdanowicz, J. Karczewski, T. Klimczuk, S. Molin, M. Strankowski, N....
-
[IMa] Electrical methods of materials and structures characterization
e-Learning Courses{mlang pl} Dyscyplina: inżynieria materiałowa Zajęcia fakultatywne dla doktorantów I i II roku Prowadzący: prof. dr hab. inż. Piotr Jasiński Liczba godzin: 15 Forma zajęć: wykład/seminarium {mlang} {mlang en} Discipline: materials engineering Facultative course for 1st and 2nd year PhD students Academic teachers: prof. dr hab. inż. Piotr Jasiński Total hours of training: 15 teaching hours Course type: lecture/seminar {mlang}
-
[NCh, IMa] Health Effects of Food Components
e-Learning Courses{mlang pl} Dyscyplina: nauki chemiczne, inżynieria materiałowa Zajęcia fakultatywne dla doktorantów I i II roku Prowadzący: prof. dr hab. inż. Agnieszka Bartoszek-Pączkowska Liczba godzin: 15 Forma zajęć: wykład {mlang} {mlang en} Discipline: chemical sciences, materials engineering Facultative course for 1st and 2nd-year PhD students Academic teachers: prof. dr hab. inż. Agnieszka Bartoszek-Pączkowska Total hours...
-
Catalytic impact of alloyed Al on the corrosion behavior of Co50Ni23Ga26Al1.0 magnetic shape memory alloy and catalysis applications for efficient electrochemical H2 generation
PublicationThe electrochemical and corrosion behaviour of Co50Ni23Ga27-xAlx (x = 0 and 1.0 wt%) magnetic shape memory alloys (MSMAs) was studied in 0.5 M NaCl solutions using various electrochemical techniques. Results showed remarkable activation of the tested MSMA toward pitting corrosion upon alloying it with Al. XPS examination confirmed the activation influence of alloyed Al. It proved that the presence of Al in the alloy's matrix weakens...
-
Metallurgical characterization and high-temperature tensile failure of Inconel 617 alloy welded by GTAW and SMAW—a comparative study
PublicationTwo types of the weld joint of Inconel 617 alloy were produced using gas tungsten arc welding (GTAW) and shielded metal arc welding (SMAW) processes with ERNiCrCoMo-1 filler metal and ENiCrCoMo-1 electrode, respectively. The weld metal showed the segregation of the principle alloying elements like Mo and Cr along the inter-dendritic spaces, triggering the formation of secondary phases. The microstructure characterization of the...
-
Changes in enzymatic activity of fish and slaughter animals meat after high pressure treatment at subzero temperatures
PublicationThe aim of this study was to determine changes in the activity of proteolytic enzymes and transglutaminase of fish and mammal meat after pressurization at subzero temperatures. The activity was measured at the optimal pHs determined for enzymes from particular types of tested meat. It was found that increasing the pressure in the range of 60–193 MPa, did not change significantly the activity of acidic proteases of cod flesh, while...
-
Robust procedure for flow coefficient calculation. W: Recent advances in simulation, computational methods and soft computing. Ed. W. Nikos, E. Ma-torakis. New York: WSEAS Press**2002 s. 152-155, 5 rys. bibliogr. 7 poz. Krzepka procedura obliczania współczynnika przepływu.
PublicationW pracy przedstawiono efektywne i szybkie metody obliczania współczynnikaprzepływu powietrza na podstawie znanych: stosunku ciśnień statycznych i oporności dźwiekowej (patrz norma ISO6358).
-
Preparation and characterization of rigid polyurethane-polyglycerolnanocomposite foams
PublicationThis work reports on the preparation of polyurethane-polyisocyanurate (PUR-PIR) foams containing different polyglycerols and layered silicate nanoclays. The rigid polyurethane foams were obtained in a laboratory scale, in a single step method, from a two-component system with a NCO to OH groups ratio equal to two. The reaction mixture consisted of the proper amounts of a commercial oligoetherpolyol, polyglycerol, catalysts, water,...
-
Mechanical, structural and diffusion studies of hydrogel polyurethane nanocomposites containing modified montmorillonite
PublicationW pracy zaprezentowano wyniki badań hydrożeli poliuretanowych zawierających poli(tlenek etylenu) oraz montmorylonit. Otrzymane układy scharakteryzowano z użyciem technik XRD, DMA, badań mechanicznych oraz wyznaczono chłonność wody i parametry dyfuzji.
-
NMR dispersion studies of poly(ethylene oxide)/sodium montmorillonitenanocomposites
PublicationPraca prezentuje wyniki badań dotyczące struktury nanokompozytów opartych na matrycy poli(tlenku etylenu) zawierającej montmorylonit sodowy. Układy zawierające PEO/MMT scharakteryzowano metodami NMR (Fast Field Cycling NMR), DSC oraz XRD.
-
Mieczysław Brdyś prof. dr hab. inż.
People -
Analiza namagnesowania w badaniach technicznych materiałów ferromagnetycznych
PublicationDo elektromagnetycznych metod badań nieniszczących stali należą m.in. polowy efekt Barkhausena (HBN) oraz emisja magnetoakustyczna (EMA). Pełne zrozumienie i optymalizacja wspomnianych technik wymaga scharakteryzowania zależności między czasoprzestrzennym stanem namagnesowania obiektu a mierzonymi wielkościami fizycznymi. Potrzebne jest podjęcie badań nad ilościowym opisem stanu namagnesowania materiałów ferrytycznych dla przypadku...
-
Possibility of Application of Magnetoacoustic Emission for the Assessment of Plastic Deformation Level in Ferrous Materials
PublicationArtykuł prezentuje wyniki badań dotyczących możliwości zastosowana emisji magnetoakustycznej (EMA) do nieniszczącej oceny stopnia deformacji plastycznej próbek poddanych jednoosiowemu rozciąganiu. Przebadane zostały cztery różne materiały: stale 13HMF, CSN12021 i P91 oraz żelazo Armco. Badania pokazały, że różne parametry magnetyczne i magnetoakustyczne badanych materiałów mogą zmieniać się w rożny sposób, jednakże zawsze obserwuje...
-
A facile approach to fabricate load-bearing porous polymer scaffolds for bone tissue engineering
PublicationBiodegradable porous scaffolds with oriented interconnected pores and high mechanical are load-bearing biomaterials for bone tissue engineering. Herein, we report a simple, non-toxic, and cost-effective method to fabricate high-strength porous biodegradable scaffolds, composed of a polymer matrix of polycaprolactone (PCL) and water-soluble poly (ethylene oxide) (PEO) as a sacrificial material by integrating annealing treatment,...
-
Opinia naukowo-techniczna dotycząca nośności pali wierconych fi 1500 mm wykonanych pod podpory wiaduktu C-3 (jezdnia prawa) na podstawie badań statycznych. Budowa Północnego Obejścia Krakowa w ciągu Drogi Krajowej nr 94 na odcinku Węzeł Radzikowskiego - Węzeł Modlnica.
PublicationOpinia dotycząca nośności pali wierconych o średnicy 1500 mm wykonanych pod podpory wiaduktu C-3 (jezdnia prawa) w ciągu Drogi Krajowej nr 94 na odcinku Węzeł Radzikowskiego - Węzeł Modlnica na podstawie badań statycznych.
-
Zastosowanie logiki rozmytej w sterowaniu na przykładzie platformy mobilnejPIONEER 2CE.**2002, 176 s. 10 fot. 77 rys. 2 tab. bibliogr. 166 poz. ma- szyn. Rozprawa doktorska /9.10.2002/. P. Gdań., Wydz. Mechaniczny. Promotor: prof. dr hab. inż. E. Wittbrodt.
Publication.
-
Modelling and analysis of a synchronous generator in more electric aircraft power system using Synopsys/Saber simulator = Modelowanie i analiza generatora synchronicznego w systemie elektroenergetycznym nowoczesnego samolotu. Zastosowanie symulatora Synopsys/Saber
PublicationStreszczenie angielskie: A model for studying synchronous machine (SM) dynamic behaviour in more electric aircraft (MEA) power system is developed and implemented in the Synopys/Saber simulation environment. The modelling language MAST has been used to elaborate the SM model. The elaborated model exhibit a network with the same number of external terminals/ports as the real SM, and represents its behaviour in terms of the electrical...