Search results for: CONCRETES
-
An experimental study of self-sensing concrete enhanced with multi-wall carbon nanotubes in wedge splitting test and DIC
PublicationConcrete is the worldwide most utilized construction material because of its very good performance, forming ability, long-term durability, and low costs. Concrete is a brittle material prone to cracking. Extensive cracking may impact durability and performance over time considerably. The addition of a small amount of carbon nanotubes (CNT) increases the concrete’s overall electrical conductivity, enabling internal structure...
-
Investigation of low-temperature cracking in newly constructed high-modulus asphalt concrete base course of a motorway pavement
PublicationThe paper presents the issue of low-temperature transverse cracks which have developed in newly constructed base courses made of high-modulus asphalt concrete mix (HMAC). Numerous transverse cracks developed in the analysed HMAC base during the winter season before the pavement was actually completed, both at the transverse joint locations and in the areas between them. This had not happened so far on such a scale during road construction...
-
Efektywność skrępowania betonu w grubościennych słupach typu Concrete-Filled Steel Tube o przekroju kołowym
PublicationW słupach typu CFST w stanie granicznym dochodzi do zwiększenia wytrzymałości betonu rdzenia na skutek jego skrępowania. Zaistnienie tego zjawiska zależy od wielu czynników. Jednym z najważniejszych z nich jest sztywność obwodowa płaszcza stalowego. Jej wpływ na efektywność wzrostu wytrzymałości betonu rdzenia przebadano eksperymentalnie na grupie 48 grubościennych słupów CFST. Wykazano, że nadmierne zwiększanie grubości płaszcza...
-
Characterization of Corrosion-Induced Fracture in Reinforced Concrete Beams Using Electrical Potential, Ultrasound and Low-Frequency Vibration
PublicationThe paper deals with the non-destructive experimental testing of the reinforced concrete beams under progressive corrosion. A series of experiments using electrical potential, ultrasound and low-frequency vibrations techniques are reported. Electrical potential and natural frequencies were used to characterise and monitor the corrosion process at its initial state. The P-wave velocity measurements were proved to be effective in...
-
Load-carrying capacity and state of effort of tubes made of glass and basalt fibre reinforced polymer filled with concrete
PublicationOpisano badania eksperymentalne słupów wykonanych z rur polimerowych zbrojonych włóknami szklanymi i bazaltowymi. Część rur wypełniano wewnątrz betonem. Słupy z wypełnieniem niszczyły się w sposób powolny, wykazując wysoką nośność pokrytyczną, podczas gdy słupy z rur pustych niszczyły się w sposób gwałtowny, niesygnalizowany. Nośności uzyskane eksperymentalnie porównano do nośności obliczonych teoretycznie na podstawie procedur...
-
State-of-the-art framework for high-speed camera and photogrammetric use in geometry evaluation of prestressed concrete failure process
PublicationPrestressed structures are a key to the realization of the boldest architectural ideas, regardless of shape complexity, great height and large span. A characteristic feature of the prestressed structure is the better use of concrete material properties by insertion of internal forces. The internal forces are opposed to external loads effects (forces and deformations of structure). Prestressed reinforced concrete beams are characterized...
-
Evaluation of pounding effects between reinforced concrete frames subjected to far-field earthquakes in terms of damage index
PublicationIn this paper, three different damage indexes were used to detect nonlinear damages in two adjacent Reinforced Concrete (RC) structures considering pounding effects. 2-, 4- and 8-story benchmark RC Moment Resisting Frames (MRFs) were selected for this purpose with 60%, 75%, and 100% of minimum separation distance and also without any in-between separation gap. These structures were analyzed using the incremental dynamic analysis...
-
Quantitative assessment of the influence of tensile softening of concrete in beams under bending by numerical simulations with XFEM and cohesive cracks
PublicationResults of the numerical simulations of the size effect phenomenon for concrete in comparison with experimental data are presented. In-plane geometrically similar notched and unnotched beams under three-point bending are analyzed. EXtended Finite Element Method (XFEM) with a cohesive softening law is used. Comprehensive parametric study with the respect to the tensile strength and the initial fracture energy is performed. Sensitivity...
-
3D X-ray Micro-CT Analysis of Rebar Corrosion in Reinforced Concrete Subjected to a Chloride-Induced Environment
PublicationThe paper presents experimental investigations of the concrete cover protective ability to coun-teract rebar corrosion in reinforced concrete cubes. To study and quantify the consequences of corrosion a reinforced concrete sample was subjected to chloride-induced environment in order to get corroded and combined with un-corroded sample. Chloride-accelerated technique can in-duce a high degree of corrosion within at a controlled...
-
Some Aspects of Shear Behavior of Soft Soil–Concrete Interfaces and Its Consequences in Pile Shaft Friction Modeling
PublicationThis paper examines the stiffness degradation and interface failure load on soft soil–concrete interface. The friction behavior and its variability is investigated. The direct shear tests under constant normal load were used to establish parameters to hyperbolic interface model which provided a good approximation of the data from instrumented piles. Four instrumented piles were used to obtain reference soil–concrete interface behavior....
-
Analytical approach for membrane action in laterally-restrained reinforced concrete square slabs under uniformly distributed loads
PublicationLaterally-restrained reinforced concrete slabs can mobilise compressive membrane action and subsequent tensile membrane action under extreme loading conditions, thereby enhancing the load resistance under uniformly distributed loads. Previous analytical study focuses primarily on tensile membrane action in simply-supported slabs. This paper describes an analytical approach for membrane action in laterally-restrained square slabs....
-
Two-dimensional simulations of concrete fracture at aggregate level with cohesive elements based on X-ray lCT images
PublicationThe paper presents results of two-dimensional meso-scale simulations of fracture in notched concrete beams subjected to three-point bending test. Concrete was assumed as a 4-phase material composed of aggregate grains placed in the cement matrix, interfacial transitional zones (ITZs) and macro-voids. The particle distribution was taken from real concrete beams on the basis of X-ray lCT images. Comprehensive numerical analyses were carried...
-
Coupled elasto-plastic-damage model with non-local softening enhanced by viscosity to describe dynamic concrete behaviour
PublicationW artykule zaproponowano model do opisu betonu podczas dynamicznego obciążenia. Przyjęto model sprężysto-plastyczny z degradacją sztywności i nielokalnym osłabieniem rozszerzony o lepkość. Obliczenia MES dla elementów betonowych pod obciążeniem dynamicznym o różnej prędkości obciążenia porównano z doświadczeniami.
-
Concrete beams under bending - calculations of size effects within stochastic elasto-plasticity with non-local softening
PublicationW artykule przedstawiono wyniki numerycznej analizy efektów skali (efektu deterministycznego i stochastycznego) w belkach betonowych nacięciem poddanych zginaniu z uwzględnieniem lokalizacji odkształceń. Obliczenia wykonano przy zastosowaniu metody elementów skończonych i sprężysto-plastycznego modelu z nielokalnym osłabieniem. Pokazano wpływ wielkości belek betonowych na nośność.
-
FE investigations of the effect of fluctuating local tensile strength on coupled energetic-statistical size effect in concrete beams
PublicationThe effect of fluctuating local tensile strength on a coupled energetic-statistical size effect in plain concrete beams under bending was numerically investigated. First, the influence of varying autocorrelation length of the random field describing a spatial variation of local tensile strength was studied. Next, the influence of the coefficient of variation of local tensile strength was analyzed. The numerical FE investigations...
-
Discrete element method simulations of fracture in concrete under uniaxial compression based on its real internal structure
PublicationThe paper describes experimental and numerical results of concrete fracture under quasi-static uniaxial compression. Experimental uniaxial compression tests were performed on concrete cubic specimens. Fracture in concrete was detected at the aggregate level by means of three non-destructive methods: three-dimensional X-ray microcomputed tomography, two-dimensional scanning electron microscope and manual two-dimensional digital...
-
A three-dimensional meso-scale approach with cohesive elements to concrete fracture based on X-ray μCT images.
PublicationArtykuł omawia wyniki numeryczne dotyczące pękania betonu uzyskane stosując trójwymiarowy model mezoskopowy z elementami kohezyjnymi. Obliczenia trójwymiarowe zostały wykonane dla zginanej belki betonowej. Beton został opisany jako model 3-fazowy. Mikrostruktura betonu odpowiadała zdjęciom tomograficznym. Wyniki numeryczne zostały porównane z wynikami doświadczalnymi. Uzyskano b. dobra zgodność między wynikami numerycznymi i doświadczalnymi.
-
Complex Concrete Structures (CE) - 2021/2022
e-Learning CoursesThe following issues in the field of concrete structures will be discussed in the lecture part: Mechanical properties of concrete and reinforcing steel; Calculation of reinforced concrete cross-sections bending; Calculation of reinforced concrete cross-sections shear; Serviceability limit state in reinforced concrete structures; Reinforced concrete slabs, one-way and cross-reinforced; Reinforced concrete stairs; Reinforced...
-
Complex Concrete Structures (CE) - 2023/2024
e-Learning CoursesThe following issues in the field of concrete structures will be discussed in the lecture part: Mechanical properties of concrete and reinforcing steel; Calculation of reinforced concrete cross-sections bending; Calculation of reinforced concrete cross-sections shear; Serviceability limit state in reinforced concrete structures; Reinforced concrete slabs, one-way and cross-reinforced; Reinforced concrete stairs; Reinforced...
-
Vibration signals collected for concrete beams with GFRP reinforcement subjected to elevated temperatures (120C-240C)
Open Research DataThe dataset contains the time domain signals obtained during dynamic tests of concrete beams reinforced with GFRP bars. The vibration were induced with the use of modal hammer, while the signals were collected by the accelerometers attached at the beam surface. The signals were captured before and after subjecting the concrete beams to elevated temperatures.
-
International Journal of Concrete Structures and Materials
Journals -
RMS-based damage identification in adhesive joint between concrete beam and steel plate using ultrasonic guided waves
PublicationAdhesive joints have numerous applications in many branches of industry, such as civil engineering, automotive, aerospace and shipbuilding. As with most structural elements, adhesive joints can experience any damage mechanism, which induces the need for diagnostic testing. Ultrasonic waves are widely used for non-destructive inspection of many structures and their elements, including adhesive joints. Guided wave propagation method...
-
Simulations of spacing of localized zones in reinforced concrete beams using elasto-plasticity and damage mechanics with non-local softening
Publication -
Computational simulations of concrete behaviour under dynamic conditions using elasto-visco-plastic model with non-local softening
Publication -
Polyethylene Terephthalate Wastes as a Partial Replacement for Fine Aggregates in Concrete Mix, Case of Jimma Town, South West Ethiopia
Publication -
Numerical investigations of discrete crack propagation in Montevideo splitting test using cohesive elements and real concrete micro-structure
PublicationThe paper is aimed at accurately predicting the discrete fracture process in concrete specimens under complex stress states in two dimensional (2D) simulations. Plain concrete specimens subjected to Montevideo splitting test (MVD) were used for consideration due to non-negligible shear stresses impact in this type of test. In order to reflect the heterogeneous nature of the concrete, the meso-structure of the samples was included...
-
Modelling of concrete facture at aggregate level using DEM based on x-ray mu CT images of internal structure
PublicationW artykule pokazano wyniki dyskretne DEM dla pękania betonu poddanego zginaniu. Beton został symulowany jako ośrodek 4-fazowy. Mikrostrukturę betonu określono na podstawie zdjęć uzyskanych mikro-tomografem. Szczególną uwagę zwrócono na zjawiska mikrostrukturalne podczas zarysowania na poziomie kruszywa.
-
Notched concrete beams under bending - calculations of size effects within stochastic elasto-plasticity with non-local softening
PublicationW artykule przedstawiono wyniki numerycznej analizy efektów skali (efektu deterministycznego i stochastycznego) w belkach betonowych nacięciem poddanych zginaniu z uwzględnieniem lokalizacji odkształceń. Obliczenia wykonano przy zastosowaniu metody elementów skończonych i sprężysto-plastycznego modelu z nielokalnym osłabieniem. Pokazano wpływ wielkości belek na nośność z uwzględnieniem stochastycznego rozkładu wytrzymałości na...
-
Simulations of spacing of localized zones in reinforced concrete beams using elastic-plasticity and damage mechanics with non-local softening
PublicationArtykuł omawia obliczanie belek żelbetowych z uwzględnieniem lokalizacji odkształceń. Obliczenia wykonano przy zastosowaniu MES na bazie sprężysto-plastycznego prawa konstytutywnego i modelu zniszczeniowego uwzględniającego degradację sztywności rozszerzonego o długość charakterystyczną mikrostruktury za pomocą teorii nielokalnej.
-
Computational simulations of concrete behaviour under dynamic conditions using elasto-visco-plastic model with non-local softening.
PublicationW artykule przedstawiono wyniki obliczeniowych symulacji zachowania betonu w warunkach dynamicznych stosując sprężysto-lepko-plastyczny model z nielokalnym osłabieniem. Wykonano obliczenia dla ściskania jednoosiowego, rozciągania jednoosiowego i zginania. Dla dużych prędkości obciążenia uwzględniono fragmentację materiału. Wyniki porównano z doswiadczeniami.
-
Modelling of concrete fracture at aggregate level using FEM and DEM based on X-ray uCT images of internal structure
PublicationArtykuł podejmuje problem pękania w zginanych belkach betonowych. Proces pękania był obserwowany przy zastosowaniu mikrotomografii . Zaobserwowany proces był symulowany numerycznie przy zastosowaniu metody elementów skończonych i metody elementów dyskretnych. Beton był opisany jako materiał 4-fazowy. Otrzymano dobrą zgodność wyników numerycznych z doświadczalnymi.
-
MODELLING OF CONCRETE FRACTURE AT AGGREGATE LEVEL USING DEM BASED ON X-RAY mu CT IMAGES OF INTERNAL STRUCTURE
PublicationThe paper describes two-dimensional meso-scale numerical results of fracture in notched concrete beams under quasi-static three-point bending. Concrete was modelled as a random heterogeneous 4-phase material composed of aggregate particles, cement matrix, interfacial transitional zones (ITZs) and air voids. As a numerical approach, the discrete element method (DEM) was used. The concrete micro-structure in calculations was directly...
-
A three-dimensional meso-scale approach to concrete fracture based on combined DEM with x-ray micro-CT images
PublicationArtykuł omawia wyniki numeryczne uzyskane stosując 3-wymiarowy mezoskopowy model do opisu pękania w betonie na poziomie kruszywa w belce z nacięciem podczas zginania. Do obliczeń użyto metodę elementów dyskretnych. Beton został opisany jako materiał 4-fazowy złożony z kruszywa, zaprawy, makro-porów i stref przejściowych miedzy kruszywem a zaprawą. Kształt i położenia kruszywa przyjęto na podstawie skanów z mikro-tomografu. Uzyskano...
-
Meso-mechanical modelling of damage in concrete using discrete element method with porous ITZs of defined width around aggregates.
PublicationArtykuł omawia wyniki obliczeń numerycznych pękania dla betonu stosując metodę elementów dyskretnych. Beton był opisany jako materiał 4-fazowy i był poddany zginaniu. W obliczeniach uwzględniono strefy ITZ o skończonej szerokości dookoła wszystkich ziaren kruszywa. Nacisk położono na przebieg mikropęknięć przy kruszywie. Wyniki porównano bezpośrednio z doświadczeniami. Obliczenia wykonano także dla szorstkich ziaren kruszywa....
-
Effect of free water on the quasi‑static compression behavior of partially‑saturated concrete with a fully coupled DEM/CFD approach.
PublicationThe work aims to numerically investigate the quasi-static response of partially fluid-saturated concrete under two-dimensional uniaxial compression at the mesoscale. We investigated how the impact of free pore fluid content (water and gas) affected the quasi-static strength of concrete. The totally and partially fluid-saturated concrete behavior was simulated using an improved pore-scale hydro-mechanical model based on DEM/CFD....
-
Mesoscopic simulations of a fracture process in reinforced concrete beam in bending using a 2D coupled DEM/micro-CT approach
PublicationW tej pracy zbadano numerycznie w warunkach 2D złożony proces pękania w krótkiej prostokątnej belce betonowej wzmocnionej jednym prętem podłużnym (bez zbrojenia pionowego) i poddanej quasi-statycznemu zginaniu w trzech punktach. Krytyczne pęknięcie poprzeczne w belce spowodowało jej uszkodzenie podczas doświadczenia. Symulacje numeryczne przeprowadzono klasyczną metodą elementów dyskretnych (DEM). Przyjęto trójfazowy opis betonu:...
-
Assessment of the application of CEM III with exposed aggregate as an alternative to CEM I for road pavements
PublicationThe article presents a results of study on the impact of replacing CEM I SR3/NA by CEMIII/A LH/HSR/NAon the mechanical properties and durability of pavement concrete with exposed aggregate. Was used granite aggregate and washed sand. Water/cement () ratio in the tested concretes constituted 0.35 and 0.4 and part of the cement was replaced with a 5% addition of natural pozzolana – zeolite. Compressive strength tests were performed...
-
Acoustic emission signals in concrete beams under 3-point bending (beams #1, #2, #3)
Open Research DataThe DataSet contains the results of the mechanical behaviour of concrete beams with dimensions 40 x 40 x 160 cm3under the 3-point bending. The beams were made of concrete with the following ingredients: cement CEM I 42.5R (330 kg/m3), aggregate 0/2 mm (710 kg/m3), aggregate 2/8 mm (664 kg/m3), aggregate 8/16 mm (500 kg/m3), water (165 kg/m3) and super-plasticizer...
-
3-D finite-difference time-domain modelling of ground penetrating radar for identification of rebars in complex reinforced concrete structures
PublicationThis paper presents numerical and experimental investigations to identify reinforcing bars using the ground penetrating radar (GPR) method. A novel element of the paper is the inspection of different arrangements of reinforcement bars. Two particular problems, i.e. detection of few adjacent transverse bars and detection of a longitudinal bar located over or under transverse reinforcement, have been raised. An attention was also...
-
Potential use of granite waste sourced from rock processing for the application as coarse aggregate in high-performance self-compacting concrete
Publication -
Crack monitoring in concrete beams under bending using ultrasonic waves and coda wave interferometry: the effect of excitation frequency on coda
PublicationConcrete is one of the most widely used construction materials in the world. In recent years, various non-destructive testing (NDT) and structural health monitoring (SHM) techniques have been investigated to improve the safety and control of the current condition of concrete structures. This study focuses on micro-crack monitoring in concrete beams. The experimental analysis was carried out on concrete elements subjected to three-point...
-
OPTICAL STRAIN MEASUREMENT OF CONCRETE VERSUS MANUAL EXTENSOMETER MEASUREMENT BASED ON THE TEST RC DEEP BEAM IN A COMPLEX STATE OF STRESS
PublicationThe purpose of this study is to compare the strain measurement techniques of concrete in R-C element subjected to the monotonic load up to the failure. In the analysis manual extensometer methods of measurements and the optical system ARAMIS for non-contact three-dimensional measurements of deformation was used. The test sample was a cantilever deep beam loaded throughout the depth which was a part of the reinforced concrete deep...
-
A coupled constitutive model for fracture in plain concrete based on continuum theory with non-local softening and eXtended Finite Element Method
PublicationThe paper presents a constitutive model for concrete which combines a continuous and discontinuous fracture description. In a continuum regime, two different constitutive laws were used. First, a plasticity model with a Rankine failure criterion and an associated fl ow rule was used. Second, a constitutive law based on isotropic damage mechanics was formulated. In order to capture the width of a localized zone and to obtain mesh-independent...
-
FE calculations of a deterministic and statistical size effect in concrete under bending within stochastic elasto-plasticity and non-local softening
PublicationW artykule przedstawiony wyniki obliczeń MES deterministycznego i statystycznego efektu skali w belkach betonowych podczas zginania. Zastosowano model w ramach stochastycznej sprężysto-plastyczności i nielokalnego osłabienia. Belki były geometrycznie podobne. Wyniki porównano z modelem efektu skali Bazanta.
-
FE-analysis of spacing of localized zones in reinforced concrete bars under tension using elasto-plasticity with non-local softening
PublicationW artykule przedstawiono wyniki numerycznej analizy lokalizacji odkształceń w pręcie żelbetowym poddanym rozciąganiu. Obliczenia wykonano przy zastosowaniu metody elementów skończonych i sprężysto-plastycznego modelu z nielokalnym osłabieniem. Pokazano wpływ różnych parametrów na nośność pręta i rozstaw lokalizacji.
-
Source code - AI models (MLM1-5 - series I-III - QNM opt)
Open Research DataSource code - AI models (MLM1-5 - series I-III - QNM opt) for the paper "Computational Complexity and Its Influence on Concrete Compressive Strength Prediction Capabilities of Machine Learning Models for Concrete Mix Design Support" accepted for publication.
-
A concerted evolution of supramolecular interactions in a {cation; metal complex; π-acid; solvent} anion-π system
Publication -
Właściwości niskotemperaturowe betonów asfaltowych o wysokim module sztywności (AC-WMS) w badaniach trzypunktowego zginania
PublicationArtykuł przedstawia właściwości niskotemperaturowe betonów asfaltowych o wysokim module sztywności. Przedstawione wyniki zostały uzyskane w dwóch badaniach zginania trzypunktowego próbek belkowych: ze stałą prędkością przemieszczenia oraz pod stałym obciążeniem. Obie te metody są od dawna stosowane na Politechnice Gdańskiej do oceny właściwości niskotemperaturowych betonów asfaltowych. Badaniu poddano pięć betonów asfaltowych –...
-
Comparative study on fracture evolution in steel fibre and bar reinforced concrete beams using acoustic emission and digital image correlation techniques
PublicationIn recent decades, the demand for sustainable construction practices has increased, but raw materials such as reinforcing steel remain scarce. Therefore, steel fibres have emerged as a popular and sustainable choice in the construction industry, offering a cost-effective alternative to traditional steel bar reinforcement for both flatwork and elevated structures. The purpose of this study is therefore to compare the performance...
-
Microcrack monitoring and fracture evolution of polyolefin and steel fibre concrete beams using integrated acoustic emission and digital image correlation techniques
PublicationThe use of polymer and steel fibres in plain concrete appears to be an excellent solution for limiting crack propagation and improving the post-ductility performance of concrete structures. Based on this premise, this study investigated the fracture evolution of polyolefin fibre-reinforced concrete (PFRC) and steel fibre-reinforced concrete (SFRC) specimens through the integrated application of two diagnostic techniques, acoustic...