Wyszukiwarka
dr inż. Krzysztof Formela
Zatrudnienie
- Profesor uczelni ze stop. nauk. dr w Katedra Technologii Polimerów
Publikacje
Filtry
wszystkich: 195
Katalog Publikacji
Rok 2021
-
Thermo-oxidative exfoliation of carbon black from ground tire rubber as potential reinforcement in green tires
PublikacjaConsidering the balance between rapidly growing global tire demand and scarcity of natural resources, recycling and reclaiming techniques of tire rubber have become the state of the art. Herein, we set out to implement a self-designed thermo-oxidative reactor for the exfoliation of carbon black (CB) from ground tire rubber, which is efficiently functioned under a thermo-oxidative reclaiming condition without any additive. The exfoliation...
Rok 2020
-
Bulk-Surface Modification of Nanoparticles for Developing Highly-Crosslinked Polymer Nanocomposites
PublikacjaSurface modification of nanoparticles with functional molecules has become a routine method to compensate for diffusion-controlled crosslinking of thermoset polymer composites at late stages of crosslinking, while bulk modification has not carefully been discussed. In this work, a highly-crosslinked model polymer nanocomposite based on epoxy and surface-bulk functionalized magnetic nanoparticles (MNPs) was developed. MNPs were...
-
Cellulose Nanofibers Isolated from the Cuscuta Reflexa Plant as a Green Reinforcement of Natural Rubber
PublikacjaIn the present work, we used the steam explosion method for the isolation of cellulose nanofiber (CNF) from Cuscuta reflexa, a parasitic plant commonly seen in Kerala and we evaluated its reinforcing efficiency in natural rubber (NR). Fourier Transform Infrared Spectroscopy (FTIR), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), and Thermogravimetric analysis (TGA) techniques...
-
Chitin nanowhiskers from shrimp shell waste as green filler in acrylonitrile-butadiene rubber: Processing and performance properties
PublikacjaIn this work, chitin nanowhiskers with high crystallinity index were obtained from shrimp shells waste using acid hydrolysis method and then comprehensively characterized. Subsequently, the impact of chitin nanowhisker content on processing and performance of acrylonitrile-butadiene rubber based nanocomposites was evaluated. The results showed that the addition of chitin nanowhiskers increased tensile strength and tear strength...
-
DETERMINATION OF THE HYDROXYL NUMBER OF GROUND TIRE RUBBER PARTICLES VIA MODIFIED TEST METHOD FOR ISOCYANATE GROUPS
PublikacjaNowadays, considering the environmental trends and law regulations associated with the circular economy, it is very important to seek for the methods of by-products and waste utilization. The example of such material, which requires the attention and recycling method is ground tire rubber generated during recycling of post-consumer car tires. It can be introduced into various polymer matrices as a filler, but to enhance its effectivity...
-
Effect of Surface Treatment of Halloysite Nanotubes (HNTs) on the Kinetics of Epoxy Resin Cure with Amines
PublikacjaThe epoxy/clay nanocomposites have been extensively considered over years because of their low cost and excellent performance. Halloysite nanotubes (HNTs) are unique 1D natural nanofillers with a hollow tubular shape and high aspect ratio. To tackle poor dispersion of the pristine halloysite (P-HNT) in the epoxy matrix, alkali surface-treated HNT (A-HNT) and epoxy silane functionalized HNT (F-HNT) were developed and cured with...
-
Enhanced interfacial and mechanical performance of styrene-butadiene rubber/silica composites compatibilized by soybean oil derived silanized plasticization
PublikacjaSilanized plasticizer (SP) was chemically derived and synthesized from soybean oil (SBO) co-vulcanized with bis-(3-(triethoxysilyl)-propyl) tetrasulfide (TESPT) by using the sulfur-accelerated curing system. SP extended styrene-butadiene rubber (SBR)/silica composites have been studied for their improved filler dispersion through coupling interaction at the SBR/silica interface. The effect of SP on cross-link density, thermal,...
-
Ground Tire Rubber Modified by Ethylene-Vinyl Acetate Copolymer: Processing, Physico-Mechanical Properties, Volatile Organic Compounds Emission and Recycling Possibility
PublikacjaGround tire rubber (GTR) was reclaimed and modified with 10 phr of ethylene-vinyl acetate copolymer via low-temperature extrusion process. Processing, physico-mechanical properties, volatile organic compounds emission, and recycling possibility were investigated. In order to better understand the impact of used modifiers, their efficiency was compared with transpolyoctenamer, which is an additive that is commercially dedicated...
-
Interface analysis of compatibilized polymer blends
PublikacjaThis chapter seeks to address the interface location in the compatibilized polymer blends and paves the way for quantitative analysis of interface in terms of interfacial tension and interfacial adhesion to provide support for understanding the relationship between morphology and ultimate properties in the compatibilized polymer blends through the lens of interface. Since understanding and analysis of interfacial phenomena in the...
-
Investigating the Impact of Curing System on Structure-Property Relationship of Natural Rubber Modified with Brewery By-Product and Ground Tire Rubber
PublikacjaThe application of wastes as a filler/reinforcement phase in polymers is a new strategy to modify the performance properties and reduce the price of biocomposites. The use of these fillers, coming from agricultural waste (cellulose/lignocellulose-based fillers) and waste rubbers, constitutes a method for the management of post-consumer waste. In this paper, highly-filled biocomposites based on natural rubber (NR) and ground tire...
-
Kinetics of Cross-Linking Reaction of Epoxy Resin with Hydroxyapatite-Functionalized Layered Double Hydroxides
PublikacjaThe cure kinetics analysis of thermoset polymer composites gives useful information about their properties. In this work, two types of layered double hydroxide (LDH) consisting of Mg2+ and Zn2+ as divalent metal ions and CO32− as an anion intercalating agent were synthesized and functionalized with hydroxyapatite (HA) to make a potential thermal resistant nanocomposite. The curing potential of the synthesized nanoplatelets in the...
-
Metal-Organic Framework (MOF)/Epoxy Coatings: A Review
PublikacjaEpoxy coatings are developing fast in order to meet the requirements of advanced materials and systems. Progress in nanomaterial science and technology has opened a new era of engineering for tailoring the bulk and surface properties of organic coatings, e.g., adhesion to the substrate, anti-corrosion, mechanical, flame-retardant, and self-healing characteristics. Metal-organic frameworks (MOFs), a subclass of coordinative polymers...
-
Microstructure and Mechanical Properties of Carboxylated Nitrile Butadiene Rubber/Epoxy/XNBR-grafted Halloysite Nanotubes Nanocomposites
PublikacjaThe effect of various amounts of carboxylated nitrile butadiene rubber (XNBR) functionalized halloysite nanotubes (XHNTs) on the cure characteristics, mechanical and swelling behavior of XNBR/epoxy compounds was experimentally and theoretically investigated. The morphology of the prepared XNBR/epoxy/XHNTs nanocomposites was imaged using scanning electron microscopy (SEM). The effects of various XNBR-grafted nanotubes on the damping...
-
Microstructure–Property Relationship of Polyurethane Foams Modified with Baltic Sea Biomass: Microcomputed Tomography vs. Scanning Electron Microscopy
PublikacjaIn this paper, novel rigid polyurethane foams modified with Baltic Sea biomass were compared with traditional petro-based polyurethane foam as reference sample. A special attention was focused on complex studies of microstructure, which was visualized and measured in 3D with high-resolution microcomputed tomography (microCT) and, as commonly applied for this purpose, scanning electron microscopy (SEM). The impact of pore volume,...
-
Modification of Ground Tire Rubber—Promising Approach for Development of Green Composites
PublikacjaGround tire rubber (GTR) was mechano-chemically modified using a road bitumen 100/150 and two types of organic peroxides: di-(2-tert-butyl-peroxyisopropyl)-benzene (BIB) and dicumyl peroxide (DCP). The impact of used additives on reactive sintering efficiency and physico-mechanical properties of modified GTR was investigated using oscillating disc rheometer measurements, followed by tensile tests and swelling behavior studies....
-
On the Correlation of Lignocellulosic Filler Composition with the Performance Properties of Poly(ε-Caprolactone) Based Biocomposites
PublikacjaIn this work, three types of agricultural waste: olive stones (OS), date seed (DS) and wheat bran (WB) were applied as potential lignocellulosic fillers in poly(ε-caprolactone) (PCL) based biocomposites. Differences in composites’ performance were related to the higher content of proteins, noted for WB comparing to other fillers applied, which enhanced plasticization of PCL matrix. The mechanical properties of biocomposites were...
-
Poloxamer: A versatile tri-block copolymer for biomedical applications
PublikacjaPoloxamers, also called Pluronic, belong to a unique class of synthetic tri-block copolymers containing central hydrophobic chains of poly(propylene oxide) sandwiched between two hydrophilic chains of poly(ethylene oxide). Some chemical characteristics of poloxamers such as temperature-dependent self-assembly and thermo-reversible behavior along with biocompatibility and physiochemical properties make poloxamer-based biomaterials...
-
Polyurethane/Silane-Functionalized ZrO2 Nanocomposite Powder Coatings: Thermal Degradation Kinetics
PublikacjaA polyurethane (PU)-based powder coating reinforced with vinyltrimethoxysilane (VTMS)-functionalized ZrO2 nanoparticles (V-ZrO2) for thermal stability was developed. Chemical structure, microstructure and thermal degradation kinetics of the prepared coatings were investigated. The peak of aliphatic C–H vibrating bond in the Fourier transform infrared (FTIR) spectrum of V-ZrO2 was a signature of VTMS attachment. Scanning electron...
-
Poly(ε-Caprolactone)/Poly(Lactic Acid) Blends Compatibilized by Peroxide Initiators: Comparison of Two Strategies
PublikacjaPoly(ε-caprolactone) (PCL) and poly(lactic acid) (PLA) blends were compatibilized by reactive blending and by copolymers formed during reaction in the solution. The reactive blending of PCL/PLA was performed using di-(2-tert-butyl-peroxyisopropyl)benzene (BIB) or dicumyl peroxide (DCP) as radical initiator. PCL-g-PLA copolymers were prepared using 1.0 wt. % of DCP or BIB via reaction in solution, which was investigated through...
-
Reactive extrusion of biodegradable aliphatic polyesters in the presence of free-radical-initiators: A review
PublikacjaNowadays, growing attention is being paid to the environment and sustainability, what fully justified research works focused on modification of biodegradable polymers and their composites. In this field of research reactive extrusion seems to be the most promising approach, which fits well to sustainable development strategy. In In the present work, the in-situ modification of biodegradable aliphatic polyesters and the compatibilization...
-
Reactive Processing and Functionalization of Ground Tire Rubber
PublikacjaThe dynamic development of the automotive industry resulted in a sig- nificant increase in rubber wastes, especially end-of-life tires, which are a serious threat to the natural environment and human health. This situation has enforced the industry and academic research groups to search new and cost-effective methods for recycling waste tires. In this field of research, reactive processing and functionaliza- tion seem to be a...
-
Reactive Sintering of Ground Tire Rubber (GTR) Modified by a Trans-Polyoctenamer Rubber and Curing Additives
PublikacjaThe proposed method of ground tire rubber (GTR) utilization involves the application of trans-polyoctenamer rubber (TOR), a commercially available waste rubber modifier. The idea was to investigate the influence of various curing additives (sulfur, N-cyclohexyl-2-benzothiazole sulfenamide (CBS), dibenzothiazole disulfide (MBTS) and di-(2-ethyl)hexylphosphorylpolysulfide (SDT)) on curing characteristics, physico-mechanical, thermal,...
-
Recent advances in compatibilization strategies of wood-polymer composites by isocyanates
PublikacjaWood-polymer composites technologies are gaining more and more attention in the scientific community, positively affecting the increase in their industrial applications, for example, automotive, building, 3D printing, etc. Many research works are focused on the improvement in matrix–lignocellulosic filler interactions to produce highly filled composites with satisfying performance properties. In this field of research, using isocyanates...
-
Reclaimed Rubber/Poly(ε‐caprolactone) Blends: Structure, Mechanical, and Thermal Properties
PublikacjaThe amount of elastomeric waste, especially from tires is constantly increasing on a global scale. The recycling of these residua should be considered a priority. Compounding the waste rubbers with other polymers can be an excellent alternative to reuse waste materials. This procedure requires solving the issue of the lack of compatibility between the waste rubber particles and other polymers. Simultaneously, there is a claim for...
-
THE IMPACT OF GROUND TIRE RUBBER TREATMENT ON THE THERMAL CONDUCTIVITY OF FLEXIBLE POLYURETHANE/GROUND TIRE RUBBER COMPOSITES
PublikacjaWaste car tires are burdensome waste, and their utilization is crucial for the natural environment. In many countries, the primary method of their recycling is energy recovery, performed by simple combustion. However, material recycling is much more effective and significantly more beneficial for the natural environment. It results in the generation of ground tire rubber, which can be used to produce polymerrubber composites. It...
-
Thermal-Resistant Polyurethane/Nanoclay Powder Coatings: Degradation Kinetics Study
PublikacjaIn the present study, thermal degradation kinetics of polyurethane (PU) powder coatings reinforced with organo-modified montmorillonite (OMMT) was investigated. PU nanocomposites were prepared in different concentrations of 1, 3, and 5 wt.% of OMMT via the extrusion method. The microstructure of the nanocomposites was observed by scanning electron microscope (SEM) illustrating uniform dispersion of OMMT nano-clay platelets in the...
-
Waste tire rubber as low-cost and environmentally-friendly modifier in thermoset polymers – a review
PublikacjaNowadays, waste tire rubber (WTR) management is a growing and serious problem. Therefore, research works focused on the development of cost-effective and environmentally-friendly methods of WTR recycling are fully justified. Incorporation of WTR into polymer matrices and composite materials attracts much attention, because this approach allows sustainable development of industrially applicable waste tires recycling technologies....
Rok 2019
-
Analiza produktów degradacji emitowanych podczas regeneracji gumy
PublikacjaWyznaczenie profilu emisji oraz wytypowanie charakterystycznych związków chemicznych uwalnianych z powierzchni opracowanych materiałów polimerowych może stanowić jeden z elementów kontroli ich jakości. W pracy przedstawiono wyniki badań emisji związków chemicznych z grupy lotnych związków organicznych uwalnianych z odpadów gumowych podczas ich przetwórstwa przy użyciu współbieżnej wytłaczarki dwuślimakowej. Ponadto, przedstawiono...
-
Cure Index demonstrates curing of epoxy composites containing silica nanoparticles of variable morphology and porosity
PublikacjaAn image was taken by Cure Index on curability of epoxy with silica nanoparticles having variable morphology and porosity. Three kinds of silica nanoparticles with non-porous curved-rod, non-porous spherical, and mesoporous spherical microstructures were synthesized and characterized by Fourier-transform infrared spectroscopy, scanning electron microscopy (SEM) and Brunauer–Emmett–Teller analyses. Epoxy nanocomposites containing...
-
Curing epoxy resin with anhydride in the presence of halloysite nanotubes: the contradictory effects of filler concentration
PublikacjaEpoxy resins can be cured with a wide variety of curing agents such as amines and anhydrides, but anhydride curing would be more favorable for research purpose because of epoxy-anhydride curing taking place slowly at room temperature. Incorporation of natural nanosized minerals into epoxy is of environmental importance. Halloysite nanotubes (HNTs) display chemical properties similar to those of silica and alumina, and hydroxyl...
-
Curing epoxy with electrochemically synthesized Zn Fe3-O4 magnetic nanoparticles
PublikacjaCathodic electrodeposition (CED) was applied in synthesis of undoped and zinc (Zn) doped Fe3O4 nanoparticles. Changes in the lattice structure of nanoparticles were monitored using X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM) supported by dispersive X-ray spectrometry (EDS), and vibrating sample magnetometry (VSM). Detailed analyses explored the formation of ZnxFe3–xO4 nanoparticles with x ≈ 0.1,...
-
Curing epoxy with ethylenediaminetetraacetic acid (EDTA) surface-functionalized Co Fe3-O4 magnetic nanoparticles
PublikacjaIn this work, the bulk and surface composition of Fe3O4 supermagnetic nanoparticles were modified for efficient epoxy curing. The bare, ethylenediaminetetraacetic acid (EDTA) capped, and cobalt (Co)-doped EDTA capped Fe3O4 nanoparticles were synthesized electrochemically. The crystalline structure and phase information, surface capping, morphology and magnetization behavior of nanoparticles were studied by X-Ray diffraction (XRD),...
-
Dynamiczna technika analizy fazy nadpowierzchniowej
PublikacjaDążność do uzyskiwania miarodajnej informacji analitycznej na temat rodzaju oraz ilości związków chemicznych emitowanych z powierzchni materiałów polimerowych stanowi istotny czynnik w procesie rozwoju technik analitycznych, jako nieodzowny element kontroli jakości opracowywanych materiałów użytkowych. W pracy naświetlono najważniejsze informacje na temat rozwiązań konstrukcyjnych i aparaturowych zaliczanych do dynamicznych technik...
-
Ground tire rubber thermo-mechanically devulcanized in the presence of waste engine oil as asphalt modifier
PublikacjaCross-linked elastomers network is main limitation for industrial usage of ground tire rubber (GTR) as asphalts’ and road pavements modifier. GTR was thermo-mechanically devulcanized via extrusion in the presence of waste engine oil (WEO) at temperature ranges from 150 to 280 °C. Combined impact of WEO content and extruder barrel temperature on the change of cross-linked structure of degraded GTR (DTGR) was investigated through...
-
Influence of microwave treatment conditions of GTR on physico-mechanical and structural properties of NBR/NR/GTR composites
PublikacjaThe increasing amount of tires used in the industry induces the researchers to find alternatives to the recycling of the end-of-life tires. Several alternatives in order to application of ground tire rubber GTR include their incorporation as a filler in composites. The main issue in this approach is the lack of compatibility between GTR and polymer matrix. In order to solve this problem the devulcanization by microwaves has been...
-
Injectable poloxamer/graphene oxide hydrogels with well‐controlled mechanical and rheological properties
PublikacjaAlthough significant progress has been made in the design and application of injectable hydrogels for biomedical applications, concurrent control of rheological and mechanical properties of injectable hydrogels has remained as an open challenge to the researchers. In this work, we introduce and put into practice a photo‐curable poloxamer (also known as Pluronic)/graphene oxide (Plu/GO) injectable hydrogel with well‐controlled rheological...
-
Microwave treatment in waste rubber recycling – recent advances and limitations
PublikacjaEnvironmentally-friendly microwave heating is increasingly used in polymer chemistry and technology. The selectivity and highly efficiency in the heat transfer present a huge advantage in systems based on recycling, improving their productivity and economic competitiveness. In case of the industrial recycling of waste rubbers, especially end-of-life tires, microwave-induced devulcanization and pyrolysis are nowadays considered...
-
Modyfikacja biodegradowalnych poliestrów alifatycznych za pomocą inicjatorów nadtlenkowych
PublikacjaCzynniki ekologiczne, ekonomiczne oraz większa świadomość społeczeństwa wpływają korzystnie na dynamiczny rozwój bio- degradowalnych materiałów, które sukcesywnie zastępują polimery „konwencjonalne”. Biodegradowalne polimery zarówno ze źródeł odnawialnych, jak i nieodnawialnych wzbudzają duże zainteresowanie wielu jednostek naukowo-badawczych oraz firm, głównie w zakresie ich modyfikacji. W pracy przedstawiono wyniki badań wpływu...
-
Modyfikacja biodegradowalnych poliestrów ialifatycznych i ich mieszanin w obecności inicjatorów nadtlenkowych.
PublikacjaStreszczenie Czynniki ekologiczne, ekonomiczne oraz większa świadomość społeczeństwa wpływają korzystnie na dynamiczny rozwój biodegradowalnych materiałów, które sukcesywnie zastępują polimery „konwencjonalne”. Na szczególną uwagę zasługują komercyjnie dostępne poliestry alifatyczne takie jak: poli(kwas mlekowy) (PLA), poli(3-hydroksymaślan) (PHB), oraz poli(ε-kaprolakton) (PCL). Jednakże ich wysoka cena oraz problemy technologiczne...
-
Preliminary Investigation on Auto-Thermal Extrusion of Ground Tire Rubber
PublikacjaGround tire rubber (GTR) was processed using an auto-thermal extrusion as a prerequisite to green reclaiming of waste rubbers. The reclaimed GTR underwent a series of tests: thermogravimetric analysis combined with Fourier-transform infrared spectroscopy (TGA-FTIR), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), and static headspace and gas chromatography-mass spectrometry (SHS-GC-MS) in order...
-
Properties of nano-Fe3O4 incorporated epoxy coatings from Cure Index perspective
PublikacjaThe mission of an advanced epoxy-based nanocomposite coating is to provide a given substrate with protection against an unwelcome guest; e.g. corrosive molecules/media, environmental stress, flame, thermal degradation or microorganisms. In such systems, the degree to which superior properties can be guaranteed depends on the state of network formation in the epoxy in the presence of nanoparticles. For low-filled epoxy nanocomposite coatings,...
-
Reclaimed rubber in-situ grafted with soybean oil as a novel green reactive plasticizer in SBR/silica compounds
PublikacjaPolymer recycling and biodegradable polymeric materials are two major routes towards the sustainable development of polymer materials which contributes to the management of waste. In this regard, an eco-friendly approach is presented wherein high reclaiming degree of ground tire rubber (GTR) was achieved by low-temperature oxidation under swollen action of soybean oil. In-situ reclaimed GTR with soybean oil was cured into reactive...
-
Structural and Thermo-Mechanical Properties of Poly(ε-caprolactone) Modified by Various Peroxide Initiators
PublikacjaThe modification of poly(ε-caprolactone) (PCL) was successfully conducted during reactive processing in the presence of dicumyl peroxide (DCP) or di-(2-tert-butyl-peroxyisopropyl)-benzene (BIB). The peroxide initiators were applied in the various amounts of 0.5 or 1.0 pbw (part by weight) into the PCL matrix. The effects of the initiator type and its concentration on the structure and mechanical and thermal properties of PCL were...
-
Studies on the Combined Impact of Starch Source and Multiple Processing on Selected Properties of Thermoplastic Starch/Ethylene-Vinyl Acetate Blends
PublikacjaThermoplastic starch (TPS)/ethylene vinyl acetate (EVA) blends compatibilized with polyethylene-graft-maleic anhydride (PE-g-MA) were prepared from various native starches (potato, maize and waxy maize) and subjected to multiple extrusion cycles. Source of starch has significant impact on its composition, hence properties of obtained TPS and their blends with EVA. Higher content of amylopectin in waxy maize starch, comparing to...
-
The Taste of Waste: The Edge of Eggshell Over Calcium Carbonate in Acrylonitrile Butadiene Rubber
PublikacjaRubber technology experiences a new age by the use of biowaste or natural fillers. In this regard, taking properties of reinforcing agents from biowaste fillers remains as the challenging matter. Chicken eggshell (ES) biowaste has recently been introduced to substitute calcium carbonate (CaCO3) duo to its superior properties and low price. In this work, composites based on acrylonitrile butadiene rubber (NBR) reinforced with ES...
-
Thermal decomposition kinetics of dynamically vulcanized polyamide 6-acrylonitrile butadiene rubber-halloysite nanotube nanocomposites
PublikacjaThermally stable thermoplastic elastomer nanocomposites based on polyamide 6 (PA6), acrylonitrile butadiene rubber (NBR), and halloysite nanotubes (HNTs) were dynamically vulcanized, and their nonisothermal decomposition kinetics were examined. The Friedman, Kissinger–Akahira–Sunose (KAS), Ozawa–Wall–Flynn (FWO), and modified Coats–Redfern (m‐CR) isoconversional models were used to obtain information about the kinetics of the thermal...
-
Towards understanding the role of peroxide initiators on compatibilization efficiency of thermoplastic elastomers highly filled with reclaimed GTR
PublikacjaThermoplastic elastomers based on recycled high density polyethylene (rHDPE) and styrene-butadiene-styrene (SBS) block copolymer were highly filled with reclaimed ground tire rubber (RR). The impact of various organic peroxides (dicumyl peroxide (DCP), benzoyl peroxide (BP) and di-tert-butyl peroxide (DB)), applied as free-radical initiators, on the processing, structure and performance properties of rHDPE/SBS/RR blends was investigated....
-
Unconditionally blue: Curing epoxy with polyethylene glycol (PEG) surface-functionalized Zn Fe3-O4 magnetic nanoparticles
PublikacjaNanoparticles govern early (chemical-controlled) and late (diffusion-controlled) stages of epoxy crosslinking, respectively. Surface functionalization of nanoparticles with macromolecules was recognized as an effective route to compensate for inadequate diffusion-controlled crosslinking. However, the effect of bulk composition amended with cations having catalytic effect towards epoxy ring opening has remained hitherto undescribed....
-
Wykorzystanie technik analitycznych do oceny emisji lotnych związków organicznych uwalnianych z materiałów polimerowych, jako obiecujące rozwiązania w kontroli ich jakości – Część 1
PublikacjaDynamiczny wzrost w zakresie wykorzystania szerokiej gamy materiałów polimerowych w produkcji przedmiotów codziennego użytku powoduje, że mogą one znacząco wpływać na rodzaj i ilość związków chemicznych występujących w środowisku zewnętrznym (outdoor), jak i w środowisku wewnętrznym (indoor), takich jak pomieszczenia mieszkalne oraz środowiska pracy (stanowiska pracy). Bardzo istotny wpływ na jakość środowiska wewnętrznego ma...
-
Wykorzystanie technik analitycznych do oceny emisji lotnych związków organicznych uwalnianych z materiałów polimerowych, jako obiecujące rozwiązania w kontroli ich jakości – Część 2
PublikacjaW pracy przedstawione zostały informacje na temat najczęściej stosowanych procedur analitycznych opartych na wykorzystaniu techniki analizy fazy nadpowierzchniowej w trybie dynamicznego pobierania próbek analitów do badania emisji związków chemicznych z grupy lotnych związków organicznych. Rozwiązanie to zostało zaproponowane, jako nowego typu podejście do oceny zmian właściwości fizyko-chemicznych materiałów polimerowych zachodzących...
wyświetlono 11583 razy