Filtry
wszystkich: 454
wybranych: 448
Filtry wybranego katalogu
Wyniki wyszukiwania dla: DYNAMIC IMPEDANCE
-
Novel microstrip low-pass filters with fractal defected ground structures
PublikacjaIn this study, three microstrip low-pass filters (LPFs) containing fractal-shaped defected ground structures have been designed and manufactured. To improve the performance of microstrip LPF, cascades of inductively coupled fractal resonators have been applied. Simultaneously, to achieve relatively constant microstrip impedance resulting in essentially low reflection losses, a modification of the strip geometry has been introduced....
-
A body position influence on ECG derived respiration
PublikacjaAn influence of a human body position on ECG derived respiration (EDR) signal is presented in the paper. Examinations were performed during deep, suspended and normal breathing for eight people in four different body positions. EDR and thoracic impedance signals were compared using correlation and standard deviation coefficients. Obtained results have shown that it is possible to monitor breath activity of people being in different...
-
Low-Cost Surrogate Modeling of Miniaturized Microwave Components Using Nested Kriging
PublikacjaIn the paper, a recently reported nested kriging methodology is employed for modeling of miniaturized microwave components. The approach is based on identifying the parameter space region that contains high-quality designs, and, subsequently, rendering the surrogate in this subset. The results obtained for a miniaturized unequal-power-split rat-race coupler and a compact three-section impedance transformer demonstrate reliability...
-
Assessment of protective properties of rubber lining in absorbers of flue gas desulphurization systems.
PublikacjaResults of research on degradation of rubber lining which is the main protection of absorbers in flue gas desulphurization (FGD) systems were presented. The power plant where the system operated is lignite-fired. Owing to measurements using electrochemical impedance spectroscopy and gravimetric determination of water content in the lining, the areas of the system which are most exposed to degradation were shown. The results obtained...
-
Investigation on accelerated impedance spectrum measurement method with multisine signal stimulation
PublikacjaThe paper presents an investigation on the accelerated impedance spectrum measurement method, oriented at parameter identification of technical objects modelled by a linear equivalent circuit, e.g. anticorrosion coatings.The method is based on multisine signal stimulation of an object and response analysis by triangle window filterbanks.It has several advantages, as compared with conventional point-by-point spectrum measurement....
-
Response features for fast EM-driven design of miniaturized impedance matching transformers
PublikacjaA framework for low-cost EM-driven design optimization of compact impedance matching transformers is presented. Our technique is based on a bottom-up design where design requirements for the transformer circuit are translated into specifications for its building blocks. These elementary cells are optimized using response features. Subsequently, the entire circuit is fine-tuned using local response surface approximation models and...
-
Remote Monitoring System for Impedance Spectroscopy using Wireless Sensor Network
PublikacjaThe architecture of a miniaturized impedanceanalyser with wireless communication module for remoteImpedance Spectroscopy (IS) of anticorrosion coatings ondifficult-to-reach objects (e.g. on the steel construction ofthe bridge) is described in this paper. Some practical aspectsof implementation of a Wireless Sensor Network (WSN) arealso discussed. A low scale, middle range, WSN networkcomposed of a Base Station (BS) with a Personal...
-
Broadband Modeling of Motor Cable Impact on Common Mode Currents in VFD
PublikacjaExamination of conducted EMI generation and propagation in AC motor drives fed by frequency converter requires to consider parasitic capacitances in converters, motor windings and feeding cables to be taken into account. AC motor winding voltage transients and related common mode currents are significantly correlated with resonance effects occurring in converter's load circuits. Intensity levels of these phenomena depend...
-
Motor Cable Influence on the Conducted EMI Emission of the Converter Fed AC Motor Drive. - Vol. 1
PublikacjaInvestigation of conducted electromagnetic interference in AC motor drives fed by pulse width modulated voltage converters requires considering parasitic capacitances in converters, motor windings and feeding cables to be taken into account. Motor voltage transients and related conducted electromagnetic emission are significantly correlated with resonance effects occurring in load circuits. The levels of intensity of these phenomena...
-
Electrical conductivity and relaxation processes in V2O5 nanorods prepared by sol–gel method
PublikacjaProperties of high purity V2O5 nanorods prepared by a sol – gel method are presented. The studied materials were characterized by: X-ray diffractometry (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). The electrical impedance was measured as a function of temperature and frequency. The obtained results show that the electrical conductivity increases with increasing temperature. The d.c. conductivity...
-
Hybrid Technique for the EM Scattering Analysis with the Use of Ring Domain Decomposition
PublikacjaA hybrid technique combining finite-element and mode-matching methods for the analysis of scattering problems in open space is presented here. The main idea is based on impedance matrix descriptions of the boundary surrounding the discrete computational domain and combine it with external field described analytically. The discrete analysis, which is the most time- and memory-consuming, is limited here only to the close proximity...
-
Insightful Analysis of Phenomena Arising at the Metal|Polymer Interphase of Au-Ti Based Non-Enzymatic Glucose Sensitive Electrodes Covered by Nafion
PublikacjaThis paper focuses on the examination of glucose oxidation processes at an electrode material composed of gold nanoparticles embedded in a titanium template. Three dierent conditions were investigated: the chloride content in the electrolyte, its ionic conductivity and the presence of a Nafion coating. The impact of the provided environment on the oxidation reaction was evaluated by cyclic voltammetry (CV) and electrochemical impedance...
-
Improvement of electrochemical action of zinc-rich paints by addition of nanoparticulate zinc
PublikacjaThe influence of nanosized particles on electrochemical action of standard zinc-rich paints by means of SEM as well as potential and impedance measurements has been investigated. The motivation for doing this was to obtain additional electrical connection between the spherical microparticles themselves and zinc particles and steel substrate. Overall zinc content was at the level of 92% by weight. Samples with different concentration...
-
Novel Structure and EM-Driven Design of Small UWB Monopole Antenna
PublikacjaA novel structure of a small UWB monopole antenna is presented. In our approach, a compact size is achieved by means of a meander line for current path enlargement as well as the two parameterized slits that introduce additional degrees of freedom helping to ensure good impedance matching. The antenna design is carried out using surrogate-based optimization involving variable-fidelity EM simulations. This allows us to simultaneously...
-
A Concept and Design Optimization of Compact Planar UWB Monopole Antenna
PublikacjaA novel structure concept of a compact UWB monopole antenna is introduced together with a low-cost design optimization procedure. Reduced footprint is achieved by introduction of a protruded ground plane for current path increase and a matching transformer to ensure wideband impedance matching. All geometrical parameters of the structure are optimized simultaneously by means of surrogate based optimization involving variable-fidelity...
-
Left-handed propagation characteristics of a dielectric and metal-loaded periodic circular waveguide
PublikacjaIn this paper, a periodic dielectric/metallic rod is located in a circular waveguide to obtain left-handed operation. Two geometries of the dielectric/metallic rod are proposed and examined. The dispersion characteristics of the investigated waveguides are obtained using a surface impedance model. Moreover, equivalent circuit models are proposed allowing for calculation of the dispersion characteristics and scattering parameters...
-
A novel sensor for measuring temperature profile during the thermoablation
PublikacjaAbstract — A novel approach for monitoring a temperature distribution inside a tissue during thermoablation is presented in the paper. A thermal profile is measured using a set of serially connected thermistors each bypassed by a capacitor. This technique allows a two-wire and simultaneous multi- point measurements using a multi-frequency measurement of electrical impedance. It is...
-
Space-mapping-based design flow of miniaturized broadband matching transformer with perforated metallization
PublikacjaA fast design procedure of unconventional passive components has been presented and experimentally validated on the basis of a wideband microstrip four-section matching transformer (50:6 OHm). A classic impedance matching circuit has been miniaturized by means of compact microstrip resonant cells (CMRCs) leading to a considerable length reduction (34%) together with minor degradation in its performance. The spacemapping-based design...
-
Determination of Mathematical Model Parameters of a Medium Frequency Transformer
PublikacjaThe paper presents the results of experimental studies of the medium frequency transformer. The object of the research was a prototype of a single-phase transformer with a core made of ferrite I-core elements and windings made of Litz conductors. The research was carried out to determine the parameters of the transformer's mathematical model. The scope of the tests included determining the magnetic hysteresis loop and measuring...
-
Electronic conductivity in the SiO2-PbO-Fe2O3 glass containing magnetic nanostructures
PublikacjaThe linear impedance spectra of iron–silicate–lead glass samples were measured in the frequency range from 1 MHz to 1 MHz and in the temperature range from 153 K to 423 K. The structure was investigated by means of XRD and atomic force microscopy. Local electrical and magnetic properties of the samples were tested with the aid of electrostatic force microscopy (EFM) and magnetic force microscopy (MFM). The obtained results show...
-
Electrochemical and photoelectrochemical properties of the interface between titania nanotubes covered by conducting polymer in aqueous by conducting polymer in aqueous electrolytes – The effect of various geometry and electrolytes concentration
PublikacjaIn the present work we show the impact of nanotubes (NTs) geometry of titania utilized as a substrate in organic-inorganic systems acting as a p-n junction on efficient conversion of radiation energy into electrochemical energy. The electrolytic bath composition and electrolysis conditions were controlled in order to obtain TiO2NTs of various geometry as a result of electrochemical oxidation of titanium foil. The electrode material...
-
Novel Coplanar-Strip-Based Excitation Technique for Design of Broadband Circularly Polarization Antennas with Wide 3-dB Axial Ratio Beamwidth
PublikacjaIn this paper, a novel excitation technique for design of a single-point-fed compact low-profile wide-slot antennas with broadband circular polarization (CP) and wide 3 dB axial ratio (AR) beamwidth is presented. Two inverted L-shape parasitic strips placed coplanar to the microstrip line of an asymmetric CPW, and a horizontal strip that protrudes from the vertical edge of the backside ground plane of the substrate are used for...
-
Impedance Studies of Phosphate-iron Glasses Containing Niobium and Titanium
PublikacjaThe ac and dc conductivity in phosphate-iron-niobate glasses with addition of titanium oxide was investigated as a function of temperature and frequency with the use of impedance spectroscopy. The topography and microstructure of glasses were investigated by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM), and confocal microscopy methods. The obtained results show that all samples are amorphous but they...
-
Phase Separation and Electrical Properties of Manganese Borosilicate Glasses
PublikacjaThe structure and electrical properties of manganese borosilicate glasses of a composition of xMnO-(0.8-x)SiO2-(0.2)B2O3 (x=0.4, 0.5 and 0.6 in mol) were investigated by impedance spectroscopy, SEM, XRD and confocal microscopy methods. The influence of composition on the glass structure and electrical properties was discussed. A separation of two amorphous phases was observed and it was concluded that one phase is SiO2-rich and...
-
A Goal-Oriented Error Estimator for Reduced Basis Method Modeling of Microwave Devices
PublikacjaThis letter proposes a novel a-posteriori error estimator suitable for the reduced order modeling of microwave circuits. Unlike the existing error estimators based on impedance function residuals, the new one exploits the residual error associated with the computation of the scattering matrix. The estimator can be effectively used in the Reduced Basis Method (RBM) to automatically generate reduced-order models. The results of numerical...
-
Analysis of Corrugated Coaxial Line with the Use of Body of Revolution and Finite Element Method
PublikacjaA combination of the body-of-revolution and finite element methods is utilized to the analysis of coaxial lines with corrugated rod and wall. Both periodic and non-periodic structures can be investigated. As the structure is axially symmetrical the two dimensional scalar-vector finite element method can be used, which allows for the investigation of complex geometries and is computationally efficient. A generalized impedance matrix...
-
Conductivity and viscosity changes of imidazolium ionic liquids induced by H2O and CO2
PublikacjaSeveral solutions of ionic liquids based on 1-ethyl-3-methylimidazolium cation saturated and unsaturated with carbon dioxide were prepared and characterized by electrochemical impedance spectroscopy. The in fluence of ILs saturation on its electrical conductivity was determined. Additionally, the in fluence of the water presence and variations of temperature on electrical properties of ionic liquids were investigated. Changes of...
-
Tailoring the electrochemical degradation of iron protected with polypyrrole films for biodegradable cardiovascular stents
PublikacjaThe degradation of polypyrrole (PPy) coated iron is studied in phosphate buffer saline solution at 37 °C by odd random phase multisine electrochemical impedance spectroscopy (ORP-EIS). PPy is electropolymerized with anti-inflammatory salicylates incorporated in the film, as a drug release system. The modelling of EIS over time provides the quantitative description of the corrosion behaviour of the material. Thus, the reliable...
-
Hybrid piezoelectric motor based on electroactive lubrication principle
PublikacjaA novel conception of hybrid piezoelectric motor is presented in this paper. Proposed conception required synchronised work of quasi-static and resonant piezoelectric actuators that results in a rotary movement. The motor's working principle is explained and the main characteristics are described. Studied topology is compared to the existing piezoelectric motors with regards to its field of applications. The assembling process...
-
Heterogeneous distribution of surface electrochemical activity in polycrystalline highly boron-doped diamond electrodes under deep anodic polarization
PublikacjaThe surface homogeneity of boron-doped diamond electrodes is variable and depends on anodic polarization conditions. The differentiation factor is the gradual and localized change in surface termination. A series of measurements under different polarization conditions was performed in order to investigate the scale of this effect. Nanoscale impedance microscopy (NIM) revealed large variation of surface resistance in individual...
-
Assessment of copper surface coverage with corrosion inhibitor using AFM-based local electrical measurements
PublikacjaThe paper presents a new method of assessment of metal surface coverage with corrosion inhibitor and thus of inhibitor protective performance. It is based on the atomic force microscopy measurement performed in a contact mode. Apart from topography images the proposed approach allows acquisition of local DC maps and local electrical impedance spectra via application of DC bias voltage or AC perturbation signal between the conductive...
-
Microstructure and Dielectric Properties of Barium-vanadate Glasses
PublikacjaThe ac and dc conductivity in barium-vanadate glasses was investigated as a function of temperature and frequency with the use of impedance spectroscopy. The topography and microstructure of glasses were investigated by the means of X-ray diffraction (XRD) and scanning electron microscopy (SEM) methods. The XRD results show that all samples are amorphous but microscopy investigation reveals that glasses with greater amount of V2O5...
-
Determination of time delay between ventricles contraction using impedance measurements
PublikacjaThe paper presents a novel approach to assessment of ventricular dyssynchrony basing on multichannel electrical impedance measurements. Using a proper placement of electrodes, the sensitivity approach allows estimating time difference between chambers contraction from over determined nonlinear system of equations. The theoretical considerations which include Finite Element Method simulations were verified using measurements on...
-
Improved performance of LaNi0.6Fe0.4O3 solid oxide fuel cell cathode by application of a thin interface cathode functional layer
PublikacjaIn this work, novel functional layers were prepared by a low temperature spray pyrolysis method on the oxygen side of the solid oxide cells. Thin layers of Ce0.8Gd0.2O2 and LaNi0.6Fe0.4O3 are prepared between the electrolyte and the porous oxygen electrode. Additionally the influence of the sprayed ceria barrier layer on the zirconia based electrolyte with the new layers is evaluated. Impedance spectroscopy results show improvement...
-
Induction machine behavioral modeling for prediction of EMI propagation.
PublikacjaThis paper presents the results of wideband behavioral modeling of an induction machine (IM). The proposed solution enables modeling the IM differential- and common-mode impedance for a frequency range from 1 kHz to 10 MHz. Methods of parameter extraction are derived from the measured IM impedances. The developed models of 1.5 kW and 7.5 kW induction machines are designed using the Saber Sketch scheme editor and simulated in the...
-
Doubly miniaturized rat-race hybrid coupler
PublikacjaTwo complementary miniaturization techniques have beenapplied to reduce the size of a rat-race hybrid coupler: (i) conventional microstrip sections have been replaced with their diminished lowimpedance counterparts as the first step of size reduction and (ii) novel fractal-shaped compact microstrip resonant cells dedicated to efficiently shorten low-impedance transmission line segments have been implemented as the second step of...
-
Efficient Finite Element Analysis of Axially Symmetrical Waveguides and Waveguide Discontinuities
PublikacjaA combination of the body-of-revolution and finite element methods is adopted for full-wave analysis of waveguides and waveguide discontinuities involving angular field variation. Such an approach is highly efficient and much more flexible than analytical techniques. The method is performed in two different cases: utilizing a generalized impedance matrix to determine the scattering parameters of a single waveguide section and utilizing...
-
A method of earth fault loop impedance measurement without unwanted tripping of RCDs
PublikacjaIn low-voltage networks, earth fault loop impedance (EFLI) measurement is the basis for assessing the effectiveness of automatic disconnection of supply. Such a measurement is performed during initial and periodical verification, especially in a TN low-voltage network. Nowadays, due to widespread application of residual current devices (RCDs), such test is difficult in many circuits because RCDs operate during the test. In this...
-
Phospholipid-functionalized gold electrode for cellular membrane interface studies - interactions between DMPC bilayer and human cystatin C
PublikacjaThis work describes the electrochemical studies on the interactions between V57G mutant of human cystatin C (hCC V57G) and membrane bilayer immobilized on the surface of a gold electrode. The electrode was modified with 6-mercaptohexan-1-ol (MCH) and 1,2-dimyristoyl-sn-glycero-3-phosphocholine (DMPC). DMPC was used as a membrane mimetic for monitoring electrochemical changes resulting from the interactions between the functionalized...
-
Locust bean gum as green and water-soluble binder for LiFePO4 and Li4Ti5O12 electrodes
PublikacjaLocust Bean Gum (LBG, carob bean gum) was investigated as an environmentally friendly, natural, and water-soluble binder for cathode (LFP) and anode (LTO) in lithium-ion batteries (Li-ion). For the frst time, we show LBG as an electrode binder and compare to those of the most popular aqueous (CMC) and conventional (PVDF) binders. The electrodes were characterized using TGA/DSC, the galvanostatic charge–discharge cycle test, cyclic...
-
Corrosion Resistance and Surface Bioactivity of Ti6Al4V Alloy after Finish Turning under Ecological Cutting Conditions
PublikacjaThe influence of cooling conditions and surface topography after finish turning of Ti6Al4V titanium alloy on corrosion resistance and surface bioactivity was analyzed. The samples were machined under dry and minimum quantity lubrication (MQL) conditions to obtain different surface roughness. The surface topographies of the processed samples were assessed and measured using an optical profilometer. The produced samples were subjected...
-
Discriminating macromolecular interactions based on an impedimetric fingerprint supported by multivariate data analysis for rapid and label-free Escherichia coli recognition in human urine
PublikacjaThis manuscript presents a novel approach to address the challenges of electrode fouling and highly complex electrode nanoarchitecture, which are primary concerns for biosensors operating in real environments. The proposed approach utilizes multiparametric impedance discriminant analysis (MIDA) to obtain a fingerprint of the macromolecular interactions on flat glassy carbon surfaces, achieved through self-organized, drop-cast,...
-
Transient States during Short-circuit in a Line Powered by UPS and its Impact on Earth Fault Loop Impedance Measurement and Power Quality
PublikacjaThe short-circuit in a line powered by Uninterruptible Power Supply (UPS) during different UPS operation modes is presented in the article. The transient state condition related to the short-circuit in a line fed from double conversion On-line UPS is discussed in detail. The results of the measurements of earth fault loop impedance (FLI) in circuits powered by UPS with the instruments of various manufacturers are presented. The...
-
Adhesion of organic coatings to hot-dip galvanized steel
PublikacjaDuplex systems provide long-time corrosion protection, much longer than the sum of the lifetimes of zinc and paint used individually. However loss of adhesion between coating and zinc substrate is often found in practice. Different methods of zinc surface preparations are used in the fi eld. The aim of this study was to examine and compare coating protection when the old zinc surface, stored during long-time period (15 years) in...
-
APPLICATION OF THE HIGH FREQUENCY LINEARIZATION OF THE EAR IN PATIENTS WITH TINNITUS . Metoda linearyzacji narządu słuchu u osób cierpiących z szumami usznymi
PublikacjaThis paper summarises the problem of tinnitus, hypotheses on its causes and the treatment methods. Moreover, a hypothesis on tinnitus origins is explained, based on the mechanisms of the analog-to-digital conversion and quantization. In addition, this paper describes methods of determining the acoustic intensity and spectra of low- level ultrasonic signals, as well as impedance characteristics of an ultrasound transducer. Furthermore,...
-
Electromagnetic interference frequencies prediction model of flyback converter for snubber design
PublikacjaSnubber design for flyback converters usually requires experimental prototype measurements or simulation based on accurate and complex models. In this study simplified circuit modelling of a flyback converter has been described to dimension snubbers in early stage of design process. Simulation based prediction of the transistor and diode ringing frequencies has been validated by measurements in a prototype setup. In that way obtained...
-
NANOCRYSTALLINE CATHODES FOR SOLID OXIDE FUEL CELLS MADE OF NOBLE METALS
PublikacjaCathodes for solid oxide fuel cells prepared by the infiltration method at 600 °C are presented. The infiltration method allows to produce stable, nanostructured electrodes. Cathodes were prepared using gold, platinum, La2NiO4+δ (L2N) and La0.6Sr0.4Co0.2Fe0.8O3 δ (LSCF). Symmetrical cathode/electrolyte/cathode samples were prepared and examined with SEM microscopy and electrochemical impedance spectroscopy. Despite successful deposition...
-
Effect of the let-through energy of overcurrent protective devices on the temperature of conductors during short-circuits
PublikacjaThe scope of the verification of low-voltage systems covers the earth fault loop impedance measurement. This measurement is usually performed with the use of low-value current meters, which force a current many times lower than the one occurring during a real short-circuit. Therefore, the international standard recommends consideration of the increase of resistance of conductors with the increase of temperature, which may occur...
-
Instantaneous Impedance Analysis of Non-Stationary Corrosion Process: a Case Study of Carbon Steel in 1M HCl
PublikacjaThe paper concerns the problem of evaluation of stationarity of carbon steel corrosion in 1M HCl. Comparison of corrosion rate with addition of corrosion inhibitor to the reference measurement is the most often used way of evaluating inhibitor efficiency. Such an approach is valid only if corrosion rate is a stationary process. Two complementary techniques were used simultaneously: volumetric analysis of evolved hydrogen and instantaneous...
-
Magnetic and capacitive couplings influence on power losses in double circuit high voltage overhead transmission line
PublikacjaPurpose – The paper aims to discuss problems of power and energy losses in a double-circuit overhead transmission line. It was observed from energymeters’ readings, that in such a line, active power losses can be measured as “negative”. The “negative” active power losses appear when the active power injected to the circuit is lower than the active power received at the circuit end. The purpose of this paper is to explain this phenomenon. Theoretical...