Filtry
wszystkich: 274
wybranych: 255
Wyniki wyszukiwania dla: STEEL BAR-REINFORCED CONCRETE
-
Modelling and parameter identification of steel–concrete composite beams in 3D rigid finite element method
Publikacja -
Mechanics of Micro- and Nano-Size Materials and Structures
PublikacjaNanotechnology knowledge is always looking to expand its boundaries to achieve the mostsignificant benefit to human life and meet the growing needs of today. In this case, we can refer tomicro- and nanosensors in micro/nano-electromechanical systems (MEMS/NEMS). These electricaldevices can detect minimal physical stimuli up to one nanometer in size. Today, micro/nano-sensordevices are widely used in the...
-
FE-analysis of spacing of localized zones in reinforced concrete bars under tension using elasto-plasticity with non-local softening
PublikacjaW artykule przedstawiono wyniki numerycznej analizy lokalizacji odkształceń w pręcie żelbetowym poddanym rozciąganiu. Obliczenia wykonano przy zastosowaniu metody elementów skończonych i sprężysto-plastycznego modelu z nielokalnym osłabieniem. Pokazano wpływ różnych parametrów na nośność pręta i rozstaw lokalizacji.
-
Experimental validation of the use of energy transfer ratio (ETR) for damage diagnosis of steel-concrete composite beams
Publikacja -
FE analysis of size effects in reinforced concrete beams without shear reinforcement based on stochastic elasto-plasticity with non-local softening.
PublikacjaW artykule przedstawiono wyniki analizy MES dotyczącej deterministycznego i statystycznego efektu skali w żelbetowych belkach bez zbrojenia na ścinanie. W analizie zastosowano prawo sprężysto-plastyczne z nielokalnym osłabieniem. Wyniki analizy porównano z doświadczeniami i modelem skali Bazanta.
-
Non-Destructive Assessment of Masonry Pillars using Ultrasonic Tomography
PublikacjaIn this paper, a condition assessment of masonry pillars is presented. Non-destructive tests were performed on an intact pillar as well as three pillars with internal inclusions in the form of a hole, a steel bar grouted by gypsum mortar, and a steel bar grouted by cement mortar. The inspection utilized ultrasonic stress waves and the reconstruction of the velocity distribution was performed by means of computed tomography. The...
-
Alternative way of the main reinforcement anchorage in reinforced short cantilevers
PublikacjaThe results of the experimental investigation of the reinforced corbels and dapped end beams with steel studs were introduced in the work. The efficiency of this type of the reinforcement was compared with the typical reinforcenet applied in reinforced conctrete construcions.
-
Monitoring system of the road embankment
PublikacjaThe paper presents the monitoring system of the embankment supported on concrete columns and overlaid by a load transfer platform (LTP) with the embedded steel grid. This field investigation was to study the complex inter-action between the columns, the LTP layer, and steel reinforcement via full-scale in situ measurements during erection of the embankment. The study was focused on the behaviour of steel reinforcement and the behaviour...
-
Guided ultrasonic waves for detection of debonding in bars partially embedded in grout
PublikacjaThis paper deals with theoretical, numerical and experimental investigations of guided wave propagation in multilayered cylindrical bars with pre-existing debonding. The research focuses on a complex description of the nature of the wave phenomena occurring in a debonded specimen with a special emphasis on the influence of the location of damage on the wave conversion and diffraction. Experimental non-destructive and destructive...
-
MONITORING SYSTEM OF THE ROAD EMBANKMENT
PublikacjaThe paper presents the analysis of the monitoring system of the embankment supported on concrete columns and overlaid by a load transfer platform with the embedded steel grid. This field investigation was to study the complex interaction among the columns, the load transfer platform layer, and steel grid via in situ measurements during erection and live loading of the embankment. The study was focused on the behaviour of steel...
-
The influence of core material on strength properties of hybrid sandwich panels
PublikacjaAlong with high prices of fuels and more restrictive safety and environmental regulations (including environment protection) increased interest in sandwich structures is being observed. One of the solution having growing application potential is steel sandwich panel. The construction consist of very thin steel plates (about 2mm) and stiffeners between them. The main advantage of using such solution is very high strength to weight...
-
Wpływ ukształtowania zbrojenia na zarysowanie i nośność żelbetowego węzła tarczowego ze wspornikiem
PublikacjaPraca ma charakter eksperymentalno-teoretyczny i dotyczy zagadnień związanych z żelbetowymi tarczami pracującymi w przestrzennym układzie konstrukcji budynków. Celem niniejszej dysertacji było określenie wpływu głównych parametrów jakimi są sposób ukształtowania zbrojenia i smukłość ścinania na zarysowanie i nośność żelbetowego przestrzennego węzła tarczowego ze wspornikiem. Na podstawie aktualnego stanu wiedzy, opracowano program...
-
Analiza doświadczalna wpływu długości zakotwienia pręta na zachowanie przyczepności w teście pull-out
PublikacjaArtykuł prezentuje badania przyczepności przeprowadzone przy użyciu testu pull-out. Eksperymenty miały na celu ocenę wpływu długości zakotwienia na przyczepność w tym teście. Z przeprowadzonej analizy wynika, że długość styku pręt-beton znacząco wpływa na zachowanie przyczepności. Określa ona typ zniszczenia połączenia, wpływa na rozkład i wartość naprężeń w pręcie oraz rzutuje na przebieg krzywej przyczepność-poślizg, która jest...
-
Teledetekcyjne badanie konstrukcyjnych elementów żelbetowych z użyciem naziemnego skaningu laserowego
PublikacjaWspółczesna technologia naziemnego skaningu laserowego (TLS) z użyciem skanerów geodezyjnych o zasięgu większym niż 50 metrów pozwala na pomiar geometrii elementów konstrukcyjnych z dokładnością bliską 1 mm. Autorzy, w oparciu o badania laboratoryjne i doświadczenia własne, prezentują rozwiązanie pozwalające na wstępną ocenę belek żelbetowych jako podstawowych elementów konstrukcyjnych budowli typu mosty, wiadukty, budynki wielkopowierzchniowe. Przedmiotem...
-
Standard and modified falling mass impact tests on preplaced aggregatefibrous concrete and slurry infiltrated fibrous concrete
PublikacjaAlthough several studies have been conducted to evaluate the impact response of concrete using theAmerican Concrete Institute (ACI) 544-2R falling mass impact test, the variations in test results are themain drawback of this testing method. This study aims to reduce the variations in experimental impacttest results by introducing two simple test setup modifications; (1) using coarse or fine aggregate bed-ding as an alternative...
-
Wybrane aspekty modelowania uderzenia pojazdem dźwigara wiaduktu
PublikacjaW pracy przedstawiono różne zagadnienia związane z uderzeniem pojazdu w dźwigar wiaduktu. Omówiono wybór modelu obliczeniowego, na podstawie porównania wyników dla modelu dźwigara zespolonego, modelu dźwigara stalowego oraz modelu wiaduktu. Następnie opisano model dźwigara zespolonego zastosowany w analizie MES oraz metodę wyznaczania współczynników tłumienia Rayleigha. Symulację numeryczną uderzenia dźwigara wiaduktu przez koparkę...
-
Impact of Tensile and Compressive Stress on Classical and Acoustic Barkhausen Effects in Grain-Oriented Electrical Steel
PublikacjaIn this paper, we present the results of the investigation of impact of tensile and compressive stress on the classical Barkhausen effect, magnetoacoustic emission (MAE) signal properties, and B(H) hysteresis loops for grain-oriented (GO) electrical steel. Samples have been glued to a nonmagnetic steel bar and stressed within elastic range (±800 μdef) by means of four-point bending method. The samples were cut out in two directions...
-
Deterioration and Protection of Concrete Elements Embedded in Contaminated Soil: A Review
PublikacjaCoating materials are considered one of the most antique materials of human civilization; they have been used for decoration and the protection of surfaces for millennia. Concrete structures—due to their permanent exposure to different types of environments and contaminants—require the use of coatings that contribute to its preservation by reducing the corrosion of its components (steel and aggregates). This article intends to...
-
Size effect in concrete under splitting tension
PublikacjaThe size effect is a fundamental phenomenon in concrete materials. It denotes that both the nominal structural strength and material ductility always decrease with increasing element size under tension. In the paper splitting tensile tests on cylindrical concrete specimens with the different diameter were carried out. Two types of the loading strip (plywood board and steel cylinder) were used. The concrete strength and ductility...
-
Analysis of load carrying capacity and destruction mechanism of an intermediate anchorage steel plate for pillar jib crane
PublikacjaPillar jib cranes are often mounted to existing floors with the use of an intermediate anchorage steel plate instead of using independent foundations, what is shown in the figure. Standards for steel design provide only basic rules for the design of such an intermediate plate. This study presents a simple design approach by using a numerical model in order to analyze different parameters that have significant influence in the anchorage...
-
The Application of Fibres from Recycled Postconsumer Tyres for Concrete Reinforcement
PublikacjaPoland as a Member State is obliged to implement the EU specific environmental legislation focused on the reduction, transport and treatment of waste. The Landfill Directive prohibited the landfilling of whole tyres and their by-products. Although the EU Directive of Waste limits the use of tyres as secondary fuel, Poland is still the EU leader in burning tyres in cement kilns. Post-consumer tyres are utilised in a number of...
-
Influence of selected additives and admixtures on underwater concrete and the environment
PublikacjaThe intensive civilization development has an influence on searching for new possibilities connected with extension of city agglomerations, both the areas of flat building and the industrial areas. One of the most interesting solution is to use water reservoirs, rivers and sea areas. The extension of buildings has an influence on building materials, especially hydrotechnical, which means development of production of hydrotechnical...
-
EXPERIMENTAL AND NUMERICAL INVESTIGATIONS OF CONCRETE BEHAVIOUR AT MESO-LEVEL DURING QUASI-STATIC SPLITTING TENSION
PublikacjaThe paper describes experimental and numerical results of quasi-static splitting tensile tests on concrete specimens at meso-scale level. The loading strip was made of plywood or steel. Fracture in concrete was detected at the aggregate level by means of three non-destructive methods: 3D x-ray micro-computed tomography, 2D scanning electron microscope and manual 2D digital microscope. The discrete element method was used to directly...
-
Przyczyny uszkodzeń i sposób naprawy posadzki ze styrobetonu
PublikacjaW artykule opisano uszkodzenia, badania i sposób naprawy posadzki wykonanej na istniejącym stropie żelbetowym o powierzchni ok. 1050 m2 i podłożu ze styrobetonu. W posadzce stwierdzono znaczne uszkodzenia w postaci zarysowań, odspojeń i nierówności. W celu określenia ich przyczyn wykonano badania in situ oraz badania laboratoryjne. Stwierdzono, że przyczyną powstania uszkodzeń są błędy wykonawcze. Wykonano próbną naprawę uszkodzeń...
-
Preliminary study of linear viscoelasticity limits of cold recycled mixtures determined in Simple Performance Tester (SPT)
PublikacjaThe publication presents methodology developed for determination of linear viscoelasticity limits for cold recycled mixtures with cement and bituminous emulsion using Simple Performance Tester (SPT). Methodology was verified on reference materials (PCV and steel dummy specimens, cement concrete and asphalt concrete) to comply with elasticity and viscoelasticity theory. The developed methodology enabled determination of linear viscoelasticity...
-
Analiza numeryczna i analityczna przekrycia w kształcie powłoki synklastycznej o podstawie kwadratowej
PublikacjaW pracy poruszono problem obliczania przekrycia żelbetowego w kształcie powłoki synklastycznej ściętej o podstawie kwadratowej. Przedstawiono obliczenia analityczne i numeryczne sił w powłoce. Powłoka jest poddana działaniu głównie sił ściskających, co jest korzystne dla tego typu konstrukcji. W strefie brzegowej i podporowej konieczne jest wymiarowanie na mimośrodowe ściskanie i rozciąganie z uwagi na znaczący wzrost momentów...
-
Effect of slag coal ash and foamed glass on the mechanical properties of two-stage concrete
PublikacjaTwo-stage concrete (TSC) is known by various names such as colcrete, Polcrete, preplaced aggregate concrete and prepacked concrete. It is different from traditional concrete in two fundamental ways, namely method of construction and mix proportion. Two-stage concrete (TSC) is defined as firstly, coarse aggregates are placed into the formwork and grout is applied to fill in the between coarse aggregate particles voids. Secondly,...
-
FRP-based reinforcement coatings of steel with application prospects in ships and offshore structures: a review
PublikacjaLatest research on novel FRP-based anti-corrosion structural coatings (for enhancing structural capacity and strengthening the coating layer) is discussed with application prospects for ships and offshore structures. In the marine environment, structures constantly face corrosion and fatigue cracks. Combining this with high operational and wave loads, it might cause a structural collapse. Recently, polymer composites have been...
-
Ultrasonic Tomography of Brick Columns Based on FEM Calculations
PublikacjaUltrasonic tomography is one of the most developed method of non-destructive testing. Despite being used mainly in medicine, it is becoming more and more popular as a method for monitoring of structural elements. It allows to examine the internal structure and technical condition of the tested element. This paper investigates the influence of crosssectional geometry on an obtained tomographic image. Wave propagation signals were...
-
Influence of separation gap on the structural response of colliding structures under earthquake excitation
PublikacjaThe high level of urbanization in the XXIst century forces the designers to design closely-separated structures and to take into account many factors influencing their response during seismic excitation, which are the most unpredictable loads which can affect civil engineering structures. Interactions between insufficiently adjacent buildings, known as the earthquake-induced structural pounding, may cause serious damage to the structures,...
-
Load capacity and serviceability conditions for footbridges made of fibre-reinforced polymer laminates = Warunki nośności i użytkowalności w odniesieniu do kładek z laminatów polimerowych
PublikacjaThe contribution is focused on derivation of the Ultimate Limit State (ULS) and Serviceability Limit State (SLS) design criteria for footbridges built of fibre-reinforced polymer matrix (FRP) laminates. The ULS design criterion is based on the design guidelines for above-ground, pressure, FRP composite tanks and the Tsai-Wu failure criterion, which is used to predict the onset of FRP laminates damage. The SLS criterion is based...
-
Improving Thermal Insulation Properties for Prefabricated Wall Components Made of Lightweight Aggregate Concrete with Open Structure
PublikacjaPorous concrete is commonly used in civil engineering due to its good thermal insulation properties in comparison with normal concrete and high compression strength in comparison with other building materials. An extremely porous concrete, called ‘lightweight aggregate concrete with open structure’ (LAC), is used in some German plants to produce prefabricated wall components. They are used mainly in hall buildings, e.g. supermarkets....
-
OCENA NOŚNOŚCI STAREGO MOSTU ŁUKOWEGO W JAGODNIKU
PublikacjaArtykuł opisuje przeprowadzoną analizę statyczno-wytrzymałościowa 95-letniego betonowego mostu łukowego zlokalizowanego w Jagodniku w północnej Polsce. Trwałość i wytrzymałość starego betonu są określane na podstawie wybranych właściwości mechanicznych, fizycznych i chemicznych. Program badań laboratoryjnych składał się z następującego zestawu badań: pomiary głębokości strefy skarbonatyzowanej i gęstości w stanie suchym, badania...
-
Wave propagation in damage assessment of ground anchors
PublikacjaThe inspection possibilities of ground anchors are limited to destructive test such as pull-out test. Guided wave propagation gives an opportunity to develop an inspection system dedicated to determine the condition of inspected element without violation of their integrity. In this paper the experimental study on wave propagation in laboratory models of ground anchors are presented. Experiments were conducted for different bonding...
-
Badania eksperymentalne słupów CFST z betonem zwykłym i ekspansywnym
PublikacjaPraca przedstawia badania eksperymentalne ponad 40 słupów CFST. Analizie poddano wyniki siły niszczącej słupy w aspekcie grubości stalowego płaszcza, smukłości słupa, rodzaju betonu wypełniającego stalową rurę (zwykły i ekspansywny) i jego wytrzymałości a także sposobu obciążania słupa (przez rdzeń lub przez cały przekrój). Sprawdzono efektywność słupów CFST z użyciem betonu ekspansywnego i zwykłego rozumianą jako stosunek nośności...
-
Wpływ zbrojenia polimerowymi włóknami rozproszonymi na wybrane właściwości mieszanek mineralno-asfaltowych
PublikacjaW artykule przedstawiono wybrane wyniki badań mieszanek mineralno-asfaltowych zbrojonych polimerowymi włóknami rozproszonymi. Ocenie poddano mieszankę włókien zbrojących aramidowo-poliolifenowych pod kątem wpływu ich zastosowania na właściwości niskotemperaturowe i odporności na deformacje trwałe mieszanek mineralno-asfaltowych. Właściwości niskotemperaturowe oceniano na podstawie testu zginania próbek belkowych oraz na podstawie...
-
Timber - material of the future. Examples of small wooden architecture structures.
PublikacjaThe aim of this article is to present various types of wood-based products, classified as engineered timber, while specifying the implications of their structural properties for their forms. Timber is used as a construction material due to its fire resistance, good structural characteristics and insulating properties. The advent of new technologies of wood processing and wood-based materials production has converted timber into...
-
Building damage due to structural pounding during earthquakes
PublikacjaEarthquake-induced pounding between adjacent buildings has been identified as one of the reasons for substantial damage or even total collapse of colliding structures. A major reason leading to interactions in buildings results from the differences in their dynamic parameters and also from insufficient distance between the structures. Although the research on structural pounding has been much advanced, the studies have mainly been...
-
Badania eksperymentalne strefy przypodporowej żelbetowych belek częściowo sprężonych
PublikacjaThis project refers to the study the shear zone, under full and partial prestressing in comparison to beams with passive reinforcement.For comparison, variable parameters have been determined:- a/d (from 1,5 to 3,5) - it's shear span to effective depth of the beam . Assuming constant geometrical quantities, "a" is variable.- 26 beams had no vertical shear reinforcement, and the other 26 had closed stirrups.- prestressing intensity...
-
Investigation on Damage-Involved Structural Response of Colliding Steel Structures during Ground Motions
PublikacjaEarthquakes are the most unpredictable damaging loads which can affect civil engineering structures. Due to insufficient separation distance between adjacent structures with different dynamic properties, structural collisions may occur during ground motions. Although the research on structural pounding has recently been much advanced, the studies have mainly been conducted for concrete structures. The aim of this paper is to show...
-
Mechanical Properties of Aluminium Bracket Strengthening
PublikacjaThe aim of the research is laboratory investigation of aluminium brackets employed to fasten lightweight curtain walls to building facilities. Tensile loads perpendicular to end plates (vertical) were applied here. The author focused on the solutions intended to increase the load-carrying capacity of aluminium brackets applying the plain washer form A (DIN 125; ISO 7089), plain washer with an outer diameter about 3d (DIN 9021;...
-
Screw displacement pile shaft deformations measured by vibrating wire and fiber optic systems during a static load test
PublikacjaThis paper describes a full scale static load test performed on a 400 mm diameter screw displacement pile equipped with four different strain measuring systems. Three types of vibrating wire strain gauges (VWSG) were used: global - retrievable, local attached to steel pipe and local concrete embedded. The fourth system was distributed fiber optic sensors based on Rayleigh back scattering (DFOS) - three in the pile cross section....
-
Load Tests of the Movable Footbridge Over the Port Canal in Ustka
PublikacjaThe paper presents the acceptance tests carried out on the open footbridge over the port canal in the Port of Ustka. The steel footbridge construction is created by a single pylon to which a movable truss span is suspended with a theoretical span of 52.3 m. The studies about load test of the object included static and dynamic extortion and measurements. In static tests the ballast was of pallets with concrete blocks. Dynamic studies...
-
LNG TANK IN ŚWINOUJŚCIE: NONLINEAR ANALYSIS OF THE TANK DOME ELEMENTS BEHAVIOUR
PublikacjaIn this paper, the dome of a tank in the Świnoujście LNG terminal is analysed. Some of the rafter ribs at the connection with hangers were not mounted during construction of the tank dome. Therefore, it has become necessary to estimate its response, which has been done with the aid of some computational models of the dome, that have been created in the finite element method environment. Different local models are studied, aiming...
-
Impact performance of novel multi-layered prepacked aggregate fibrous composites under compression and bending
PublikacjaMulti-layered Prepacked aggregate fibrous composite (MLPAFC) is a new type of concrete, which is prepared in two subsequent stages of aggregate-fibre skeleton prepacking and cementitious grouting. In this study, ten MLPAFC mixtures were prepared in three subsequent layers incorporating different contents of four different types of steel fibres. Long and short hooked-end and crimped steel fibers were adopted with 3.0 and 1.5% dosages...
-
The geodetic monitoring of the engineering structure – a practical solution of the problem in 3D space
PublikacjaThe study raises the issues concerning the automatic system designed for the monitoring of movement of controlled points, located on the roof covering of the Forest Opera in Sopot. It presents the calculation algorithm proposed by authors. It takes into account the specific design and location of the test object. High forest stand makes it difficult to use distant reference points. Hence the reference points used to study the stability...
-
Instalacja oświetleniowa w zbiorniku wody "Stary Sobieski" - rozważania o spektakularnym zabytku techniki
PublikacjaArtykuł przedstawia efekty badań autora nad niezwykle okazałą, ponad stuletnią instalacją elektryczną, która zachowała się w zabytkowym obiekcie infrastruktury wodociągowej w niemal 100% oryginalnej formie (nie licząc częściowej dewastacji). Jest to rzadki przykład tego rodzaju zabytku, ponieważ obiekty tego typu i w tym wieku zwykle podlegały modernizacji na przestrzeni lat albo, po wyłączeniu z eksploatacji zostały całkowicie...
-
The use of fibre-reinforced polymers (FRP) in bridges as a favourable solution for the environment
PublikacjaThe purpose of this article is to show the modern engineering, in which sustainability and taking care of ecology play a significant role. The authors are focused on FRP composite materials and their applications in civil engineering. Case studies showing renovation and design of new bridges with the use of FRP are presented and discussed to clarify benefits, which this solution provides. Main advantages of FRP materials in comparison...
-
The effect of road restraint systems on the level of road safety - Polish experience
PublikacjaRoadside accidents happen when a vehicle runs off the road. The majority of these accidents are very severe because leaving the road is usually followed by hitting a solid obstacle (tree, pole, support, culvert front wall, barrier). Roadsides are some of the most important issues of road safety. They have been studied for years to identify roadside hazards and the effectiveness of road safety measures such as restraint systems....
-
Analiza kosztów i czasu budowy domu jednorodzinnego w technologii drewna krzyżowo klejonego CLT
Publikacja-