Filtry
wszystkich: 431
wybranych: 418
Wyniki wyszukiwania dla: BEARING SYSTEMS
-
Report of Eurocode 7 application for pile foundation design in Poland
PublikacjaThe EC7 rules of geotechnical design are in use in Poland for several years, even though there is no National annex. With regard to pile foundations, there are valid EC7 recommendations concerning design approaches, load partial coefficients, correlation coefficients and capacity partial coefficients. Polish designers can be quite flexible when it comes to choose a method for static, bearing capacity and settlement calculations....
-
Influence of Protonation State on the Excited State Dynamics of a Photobiologically Active Ru(II) Dyad
PublikacjaThe influence of ligand protonation on the photophysics of a ruthenium (Ru) dyad bearing the 2-(1-pyrenyl)-1H-imidazo[4,5-f][1,10]-phenanthroline (ippy) ligand was investigated by time-resolved transient absorption spectroscopy. It was found that changes in the protonation state of the imidazole group led to changes in the electronic configuration of the lowest lying excited state. Formation of the fully deprotonated imidazole...
-
AN ATTEMPT AT IDENTIFYING THE INFLUENCE OF TEST HEAD ASSEMBLY STIFFNESS ON THE RESULTS OF A TRIBOLOGICAL EXPERIMENT CONDUCTED UNDER MICRO-OSCILLATION CONDITIONS
PublikacjaThe outcome of experimental research on a group of dry bearing materials carried out under small oscillation conditi ons and using a test rig designed and made at Gdansk University of Technology inspired the decision to find out if the stiffness of test head elements in fluenced the generated results. Therefore, a computer model utilising finite elements was devised and used to simulate the workings of the test head. The mode l...
-
Three-point bending test of sandwich beams supporting the GFRP footbridge design process - validation
PublikacjaSome selected aspects concerning material and construction design issues for pedestrian footbridge made of GFRP composite materials are elaborated in this paper. The analysis is focused on validation tests, which are particularly important because of the advanced technology and materials that are used for this innovative bridge. The considered footbridge is a sandwich-type shell structure comprising of PET foam core and outer skins...
-
Typology, current state and non-destructive testing of timber roof trusses of historic churches in the West Vistula Delta, Poland
PublikacjaThis paper presents the current state of conservation of historic roof churches located in the Żuławy of Gdańsk (Poland). It also describes the architecture of these temples, the region itself and old carpentry techniques for constructing roof trusses. Interdisciplinary tests were carried out in six churches. The geometry of the load bearing structures, the moisture content and the carpentry technique were specified. The field...
-
Novel Nonlinear High Order Technologies for Damage Diagnosis of Complex Assets
PublikacjaFor the first time worldwide, innovative techniques, generic non-linear higher-order unnormalized cross-correlations of spectral moduli, for the diagnosis of complex assets, are proposed. The normalization of the proposed techniques is based on the absolute central moments, that have been proposed and widely investigated in mathematical works. The existing higher-order, crosscovariances of complex spectral components are not sufficiently...
-
Novel Diazocrowns with Pyrrole Residue as Lead(II) Colorimetric Probes
PublikacjaNovel 18- and 23-membered diazomacrocycles were obtained with satisfactory yields by diazocoupling of aromatic diamines with pyrrole in reactions carried under high dilution conditions. X-ray structure of macrocycle bearing five carbon atoms linkage was determined and described. Compounds were characterized as chromogenic heavy metal ions receptors. Selective color and spectral response for lead(II) was found in acetonitrile and...
-
Exploring the Reactivity of Unsymmetrical Diphosphanes toward Heterocumulenes: Access to Phosphanyl and Phosphoryl Derivatives of Amides, Imines, and Iminoamides
PublikacjaWe present a comprehensive study on the diphosphanation of iso(thio)cyanates by unsymmetrical diphosphanes. The reactions involving unsymmetrical diphosphanes and phenyl isocyanate or phenyl thioisocyanate gave rise to phosphanyl, phosphoryl, and thiophosphoryl derivatives of amides, imines, and iminoamides. The structures of the diphosphanation products were confirmed through NMR spectroscopy, IR spectroscopy, and single-crystal...
-
Chemical and Mechanical Properties of 70-Year-Old Concrete
PublikacjaThe aim of this research is to determine the durability and strength of concrete continuous footing based on the chosen mechanical, physical, and chemical properties of the concrete. The presented investigations constitute some opinions from experts on the bearing capacity of concrete continuous footing and the possibilities of carrying additional loads and extended working life. The cylindrical specimens were taken from continuous...
-
DEFORMATIONS OF INNOVATIVE COLD-FORMED GEB SECTIONS
PublikacjaPermanent urban growth of the world of today world implies demanding challenges for the steel construction industry. Nowadays, one of the most important issues is the cost optimization of steel structures. Since the weight of building materials is a major component of the total cost, engineers and designers try to reduce structural weight, without compromising durability and sustainability of a steel structure. Therefore, light...
-
The determinants of morphology and properties of the nanohydroxyapatite coating deposited on the Ti13Zr13Nb alloy by electrophoretic techniqe
PublikacjaThe titanium and its alloys belong at present to the most preferred and commonly applied biomaterials for load- bearing implants. The surfaces of biomaterials are subjected to modification, including the hydroxyapatite coatings deposited in order to ensure corrosion resistance and better joining between an implant and a bone through the possibility of ingrowth bone into the coating. In this paper, the morphology and properties...
-
The effect of a belt position in the spindle driving system on critical rotational speeds
PublikacjaThe aim of this paper was to examine how the belt pulley position affects critical rotational speeds of the modernized spindle of the sliding table saw Fx3. Methodology of determination of critical rotational speeds of the spindle in a function of the spindle design features and its driving system is presented. Spindles in these kind of machine tools are mainly driven with V-belts, and the pulleys on the spindles might be positioned:...
-
Composite GFRP U-shaped footbridge
PublikacjaThe paper presents proposals for the use of glass fiber reinforced polymer composites for the construction of engineering objects, known and commonly used in the shipbuilding industry. An example of a pedestrian footbridge was used in this case, which, despite the considerable thickness of the structural material, was made using infusion technology in one production cycle. The designed and produced footbridge span is durable, dynamically...
-
1,3,4-Thiadiazole-based diamides: Synthesis and complexation properties
PublikacjaAromatic diamides, derivative of 2,6-pyridinedicarboxylic acid and isophthalic acid, bearing 1,3,4-thiadiazole residue were prepared with satisfactory yields in conventional procedures and microwave stimulated reactions. X-ray structure of N,N-bis (1,3,4-thiadiazol-2-yl)-2,6-pyridinedicarboxamide (2) DMSO solvate (2DMSO) was described. Selective zinc(II), lanthanum(III), terbium(III) and L-tyrosine recognition was found for N,N-bis(1,3,4-thiadiazol-2-yl)-2,6-pyridinedicarboxamide...
-
Implementation of DIFAR Processing in ASW Dipping Sonar
PublikacjaThis paper presents the implementation of the signal processing algorithm used by buoy DIFAR (Directional Frequency Analysis and Recording), that is fully operational on Polish Navy anti-submarine warfare (ASW) helicopters and ships, applied to dipping sonars for detection and tracking of submarines. The development of the DSP algorithms was a part of the modernization of sonars conducted at the Gdansk University of Technology....
-
Hydrogen and chalcogen bonds in crystals of chalcogenadiazolecarboxylic acids – competition or cooperation?
PublikacjaThis article presents crystal structures of chalcogenadiazolecarboxylic acids bearing both a hydrogen and a chalcogen bond donor. The selected molecules varied in the size of the aromatic unit, the chalcogen atom and/or the position of the carboxyl group in the core structure. The most common synthons in their lattice are "R" _"2" ^"2" (8) self-complementary acid dimers or four-membered [Ch···N]2 rings. Supramolecular synthons...
-
Correlation between natural frequencies and buckling load in a stiffened shell
PublikacjaThe paper deals with correlation between natural frequencies and buckling load of a stiffened shell composed of corrugated sheets and vertical stiffeners (columns). The simplified shell segment represents the buckling behaviour of a whole silo with sparsely distributed columns. The paper covers variants of linear buckling anal-yses, dynamic eigenvalue analyses and geometrically non-linear analyses of a segment modelled with shell...
-
Displacement measurements during load testing of railway arch bridge
PublikacjaThe paper discusses issues concerning load tests carried out on a twin-track, arch railway bridge over the Martwa Wisla river in Gdansk. Currently, it is the bridge with the longest span in its class in Poland. The load-bearing structure consists of three no-hinge arches and an orthotropic deck suspended from them. The studies of the structure assumed the performing of static and dynamic tests. The paper presents the method for...
-
Experimental study on steel columns subjected to impact load under earthquake conditions
PublikacjaEarthquakes affecting urbanized regions cause exceptional loads to load bearing structural elements such as columns. Such a boost in the load conditions can lead to severe damages which, in a worst case scenario, can lead to a total collapse of a building. This boost is caused by the horizontal ground movement generating a rise in the internal forces due to considerable large displacement between the top and bottom support of columns....
-
Highly linear self-assembled porphyrin wires
PublikacjaAn efficient noncovalent assembly process involving high geometrical control was applied to a linear bis(imidazolyl zinc porphyrin) 7Zn, bearing C18 substitutents, to generate linear multiporphyrin wires. The association process is based on imidazole recognition within the cavity of the phenanthroline-strapped zinc porphyrin. In chlorinated solvents, discrete soluble oligomers were obtained after (7Zn)n was end-capped with a terminal...
-
Sustainable development requires risky decisions - problematic 300 ton overweight transport passing a bridge
PublikacjaOversize load passages over bridges are one of the research issues related to sustainable development that engineering and scientific teams around the world have to deal with . The article presents the scope of activities that enabled the passage of an oversized vehicle with a total weight of over 300 tons over a reinforced concrete slab. The bridge load capacity is 30 tons. In order to assess the capacity of the bridge, detailed...
-
Modeling and Strength Calculations of Parts Made Using 3D Printing Technology and Mounted in a Custom-Made Lower Limb Exoskeleton
PublikacjaThis study is focused on the application of 3D-printed elements and conventional elements to create a prototype of a custom-made exoskeleton for lower limb rehabilitation. The 3D-printed elements were produced by using Fused Deposition Modeling technology and acrylonitrile butadiene styrene (ABS) material. The scope of this work involved the design and construction of an exoskeleton, experimental testing of the ABS material and...
-
Case Study of Old Steel Riveted Railway Truss Bridge: From Material Characterization to Structural Analysis
PublikacjaThe structural analysis of an old steel riveted railway truss bridge located over the Maruska River on the Działdowo – Olsztyn, Poland railway line is performed in this paper to check its behaviour under today’s railway loads. The mechanical properties of construction steel extracted from the old steel bridge are investigated by tensile tests, impact tests through the Charpy pendulum impact V-notch, and an optical emission spectrometer....
-
Simulation Environment in Python for Ship Encounter Situations
PublikacjaTo assess the risk of collision in radar navigation distance-based safety measures such as Distance at the Closest Point of Approach and Time to the Closest Point of Approach are most commonly used. Also Bow Crossing Range and Bow Crossing Time measures are good complement to the picture of the meeting situation. When ship safety domain is considered then Degree of Domain Violation and Time to Domain Violation can be applied. This...
-
Predicting the impact of traffic–induced vibrations on buildings using artificial neural networks
PublikacjaTraffic–induced vibrations may constitute a considerable load to a building, cause cracking of plaster, cracks in load–bearing elements or even a global structural collapse of the whole structure [1-4]. Vibrations measurements of real structures are costly and laborious, not justified in all cases. The aim of the paper is to create an original algorithm, to predict the negative dynamic impact on the examined residential building...
-
Polymeric Bearings as a new base isolation system suitable for mitigating machine-induced vibrations
PublikacjaThe present paper summarizes the preliminary results of the experimental shaking table investigation conducted in order to verify the effectiveness of a new base isolation system consisting of Polymeric Bearings in reducing strong horizontal machine-induced vibrations. Polymeric Bearing considered in the present study is a prototype base isolation system, which was constructed with the use of a specially prepared flexible polymer...
-
A 95-Year-Old Concrete Arch Bridge: From Materials Characterization to Structural Analysis
PublikacjaThe structural analysis of a 95-year-old concrete arch bridge located in Jagodnik (Poland) is performed in this paper, in order to check its behavior under today’s traffic loads. The mechanical properties of both the concrete and the reinforcement are investigated by testing cores and bar stubs extracted from the bridge. Structural analysis confirms that the bridge meets today’s load requirements in terms of bearing capacity, serviceability...
-
Innovative cold-formed GEB section under compression
PublikacjaCold-formed steel sections extensively affect the modern steel construction industry. Not only are they used as secondary elements like purlins or sheeting, but also they can serve as primary load-bearing members in fabricated steel panels and trusses. A new cross-section called shortly a GEB may serve as that member. However, its existence of the metal building structures industry depends on the exact, optimal dimensional parameters...
-
Cure kinetics of epoxy/MWCNTs nanocomposites: Isothermal calorimetric and rheological analyses
PublikacjaA combinatorial route has been applied in cure kinetics study of epoxy nanocomposites containing multi-walled carbon nanotubes (MWCNTs) based on differential scanning calorimetry and rheokinetic analyses under isothermal conditions. Pristine and amine-modified MWCNTs bearing primary and secondary amines were used at very low concentrations (0.1 and 0.3 wt.% based on epoxy weight). Model-free and model-fitting methods were applied...
-
Numerical Simulations of Hydrodynamic Open-Water Characteristics of a Ship Propeller
PublikacjaThe paper presents the results of numerical simulations of ship propeller operation bearing the name of Propeller Open Water (POW) Tests. The object of tests was a sample ship propeller (PPTC1), the geometrical and kinematic data of which are available, along with the results of model tests, on the official page of the research centre involved in the measurements. The research aimed at verifying the correctness of results of numerical...
-
Study of railway traffic safety based on the railway track condition monitoring system
PublikacjaThe solution to the problem of monitoring the railway track, as well as potentially dangerous objects and phenomena in the adjacent territories, is determined by the need to implement increased requirements for traffic safety (primarily to the geometric parameters of the devices of a long railway track under construction and functioning load-bearing highways), prevention of technological disasters and large-scale negative effects...
-
Analysis of ring cracks in ceramic rolling elements using the boundary element method
PublikacjaCeramic materials have been increasingly used in bearing technology for over a dozen years. This is due to the characteristic properties of ceramic materials such as: high hardness, corrosion resistance, the possibility of use in aggressive chemical environments, as well as due to the lower specific weight compared to steel materials. However, the use of ceramic materials is connected with many limitations. The main disadvantages...
-
THE CONCEPT OF MODELING OF SNOW IMPACT ON THE STRUCTURE OF THE SUSPENDED TAURON ARENA ROOF IN CRACOW
PublikacjaThe article presents studies and numerical simulations on modeling snow influence on TAURON ARENA suspended roof structure in Cracow. The scope of work includes experimental tests, functions solutions taking into account various cases of snow impact according to PN and EC, as well as numerical simulations for the sport and entertainment arena in the Czyzyny district. The FEM roof structure model developed in the SOFISITK software...
-
The LaPdIn 4 indide and elementary properties of the LaTIn 4 ( T = Ni, Pd, Pt) materials family
PublikacjaThe indium-rich intermetallic compound LaPdIn4 is reported, prepared by arc-melting and annealing at 600 C. Single crystal X-ray diffraction found the material to be orthorhombic, space group Cmcm (No. 63), with lattice parameters a ¼ 4.5462(3) Å, b ¼ 16.9208(10) Å, and c ¼ 7.3100(5) Å. This previously unreported indide is isostructural with LaNiIn4 and LaPtIn4. It is demonstrated that all three compounds in the LaTIn4 (T ¼ Ni,...
-
Reliability assessment of an OVH HV power line truss transmission tower subjected to seismic loading
PublikacjaThe study focuses on the reliability of a transmission tower OS24 ON150 + 10, an element of an OVH HV power line, under seismic loading. In order to describe the seismic force, the real-life recording of the horizontal component of the El Centro earthquake was adopted. The amplitude and the period of this excitation are assumed random, their variation is described by Weibull distribution. The possible space state of the phenomenon...
-
Crack propoagation in MgO-PSZ ceramic materials
PublikacjaThe properties of ceramic materials such as elevated hardness, high temperature capability, low coefficient of thermal expansion are of interest for rolling element materials. Widely used ceramic materials in engineering applications are silicon nitride, zirconia and alumina. The paper presents an experimental study of the fatigue life of MgO-PSZ ceramic material in lubricated contact with defined types of cracks. A ceramic angular...
-
One year performance evaluation of low volume road with cold recycled base course on the basis of FWD and Dynamic Modulus tests
PublikacjaArticle presents results of assessment of performance of trial section of flexible pavement with cold recycled base constructed on low volume road within typical contract conditions. Performance evaluation was made based on Falling Weight Deflectometer (FWD) test performed during construction stage – 2 times on the top of cold recycled base course – 28 and 180 days after compaction of base course and 2 times on the top of the wearing...
-
Model tests of cast-in-place piles formed by using different types of auger
PublikacjaModel tests are still a popular research tool used to observe and determine the mechanisms of pile-soil interaction. Due to the significant scale effect, the results of model tests performed in the 1g system can only be analysed from the qualitative side. This article describes and presents the results of 1g pile model tests carried out for comparative purposes. There were tested the effectiveness and efficiency of various types...
-
Towards Greater Citizen Participation in Financing Public Cultural Institutions—Legal Barriers and Proposed Solutions
PublikacjaThe paper contains a conceptual proposal that aims at indicating new models of participatory financing of cultural institutions as well as actions towards supporting culture. It presents results of a qualitative study in the form of action research, on identifying legal barriers of financing of cultural institutions in Poland. Additionally, it presents practical suggestions to the encountered problems that were worked out after...
-
Verification of punching shear outside the shear cap by the direct method
PublikacjaThe proposition of a method to verify the punching resistance for very large supports based on the EN 1992-1-1 standard is described in this paper. The present standard guidelines for the calculation of the punching resistance for large supports are also summarised. The proposed direct method is compared with other standard methods using an example taken from design practice. This method consists of a direct check of the shear...
-
Surface Texture Analysis of Hardened Shafts after Ceramic Ball Burnishing
PublikacjaThis article represents the results of testing the surface condition of shafts manufactured by the burnishing process. The shafts with a hardness of approximately 62 HRC (Rockwell C). were burnished with a ceramic ball (Si3N4), where the force range was controlled by the means of a hydraulic system. The machining process consisted of hard turning shafts with cubic boron nitride (CBN) inserts, followed by burnishing with the use...
-
Tacit Knowledge Sharing and Project Performance. Does the Knowledge Workers' Personal Branding Matter?
PublikacjaTacit knowledge sharing is the real challenge for knowledge management today. Network economy has completely changed the role of knowledge workers who now become independent tacit knowledge producers. Bearing this fact in mind, the author studied how tacit knowledge sharing affects the process of building a personal brand and project performance. For this purpose, the authors conducted a study among Polish professionals with different...
-
Materials Design for the Titanium Scaffold Based Implant
PublikacjaThe main objective of here presented research is a design the scaffold/porous titanium(Ti) alloy based composite material demonstrating better biocompatibility, longer lifetime andbioactivity behaviour for load-bearing implants. The development of such material is proposed bymaking a number of consecutive tasks. Modelling the mechanical, biomechanical and biologicalbehavior of porous titanium structure and an elaboration of results...
-
Materials Design for the Titanium Scaffold Based Implant
PublikacjaThe main objective of here presented research is a design the scaffold/porous titanium(Ti) alloy based composite material demonstrating better biocompatibility, longer lifetime andbioactivity behaviour for load-bearing implants. The development of such material is proposed bymaking a number of consecutive tasks. Modelling the mechanical, biomechanical and biologicalbehavior of porous titanium structure and an elaboration of results...
-
Photochemical Rearrangement of a 19-Membered Azoxybenzocrown: Products and their Properties
PublikacjaThe preparation and characterization of products of the chemical and photochemical rearrangements of a 19-membered o,o'-azoxybenzocrown were presented. In photochemical rearrangement, besides expected product i.e. 19-membered o-hydroxy-o,o'-azobenzocrown (19-o-OH), obtained under defined conditions with 75% yield, also other macrocyclic products were isolated and identified, namely: 19-membered p-hydroxy-o,o'-azobenzocrown (19-p-OH),...
-
Shear fracture of longitudinally reinforced concrete beams under bending using Digital Image Correlation and FE simulations with concrete micro-structure based on X-ray micro-computed tomography images
PublikacjaThe paper presents experimental and numerical investigations of the shear fracture in rectangular concrete beams longitudinally reinforced with steel or basalt bar under quasi-static three point bending. Shear fracture process zone formation and development on the surface of beams was investigated by Digital Image Correlation (DIC) whereas thorough analyses of 3D material micro-structure, air voids, width and curvature of shear...
-
A Proposed Machine Learning Model for Forecasting Impact of Traffic-Induced Vibrations on Buildings
PublikacjaTraffic-induced vibrations may cause various damages to buildings located near the road, including cracking of plaster, cracks in load-bearing elements or even collapse of the whole structure. Measurements of vibrations of real buildings are costly and laborious. Therefore the aim of the research is to propose the original numerical algorithm which allows us to predict, with high probability, the nega-tive dynamic impact of traffic-induced...
-
Comparative wear test of journal sliding bearings with sintered bronze and Babbitt alloy bushes lubricated by environmentally acceptable/adapted lubricants (EAL)
PublikacjaA growing awareness of the negative effects of mineral oils on the natural environment has resulted in the introduction of new regulations related to environmental protection. One of these regulations requires the use of environmentally acceptable/adapted lubricants (EAL) to lubricate marine main shaft bearings, in place of the mineral lubricating oils that have been used for decades. Classification Societies, which supervise...
-
Analysis of Failure Mechanism in Joints with Positive Eccentricity in CFS Truss
PublikacjaThe paper presents studies concerning the load-bearing capacity of truss joints with a positive eccentricity resulting from the arrangement of geometric members and the failure mechanisms observed in the joints. Based on the previously conducted experimental study, a numerical model of the tested fragment of the CFS truss with eccentricity in the joint was created and validated. All structural details of the tested truss and the...
-
Vibro piles performance prediction using result of CPT
PublikacjaVibro piles belong to the group of full displacement piles with an expanded base, characterised by a very high load capacity, especially in non-cohesive soils. The problem is to adopt a reliable method for the determination of full load–settlement (Q–s) curve. A frequent difficulty is the determination of the load capacity limit based on the static load test because the course of the load–settlement curve is of a linear nature....