Filtry
wszystkich: 780
wybranych: 670
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: SIMULATION STUDY
-
Simulation-Based Design of Microstrip Linear Antenna Arrays Using Fast Radiation Response Surrogates
PublikacjaFast yet accurate technique for simulation-based design of linear arrays of microstrip patch antennas is presented. Our technique includes: (i) optimization of the corrected array factor of the antenna array under design for a phase excitation taper resulting in reduced side lobes; (ii) simulation-driven optimization of the array element for element dimensions resulting in matching at and about operational frequency, and (iii)...
-
Simulation of the Remanence Influence on the Transient States of the Single-Phase Transformer Including Feedback Preisach Model
PublikacjaThis paper presents the results of the experimental and simulation investigation concerning the influence of remanence in the core of a single-phase transformer at the no-load transient state. Experimental studies consisted of the discharge of the capacitor through the primary winding at several different values of the residual magnetic flux. The paper presents a model of the transformer test system, taking into account the magnetic...
-
Expedited Simulation-Driven Multi-Objective Design Optimization of Quasi-Isotropic Dielectric Resonator Antenna
PublikacjaMajority of practical engineering design problems require simultaneous handling of several criteria. Although many of design tasks can be turned into single-objective problems using sufficient formulations, in some situations, acquiring comprehensive knowledge about possible trade-offs between conflicting objectives may be necessary. This calls for multi-objective optimization that aims at identifying a set of alternative, Pareto-optimal...
-
Design and simulation of a new prototype of piezoelectric cantilever sensor/actuator for analysis of the soft tissues properties
PublikacjaThis paper is devoted to a new prototype of piezoelectric cantilever transducer dedicated for the characterization of the mechanical properties of soft tissues. General description of the actuator’s structure is presented including the basic principles of the measurement. The chosen geometry of the prototype is discussed and compared with the existing one. Constitutive equations are presented for the active and passive layer of...
-
Low-cost EM-Simulation-based Multi-objective Design Optimization of Miniaturized Microwave Structures
PublikacjaIn this work, a simple yet reliable technique for fast multi-objective design optimization of miniaturized microwave structures is discussed. The proposed methodology is based on point-by-point identification of a Pareto-optimal set of designs representing the best possible trade-offs between conflicting objectives such as electrical performance parameters as well as the size of the structure of interest. For the sake of computational...
-
Computational simulation of motion of a rescue module during its launching from ship at rough sea
PublikacjaThis paper is a continuation of the work titled : “A comp utational model for simulation of motion of rescue module during its launching from stern ramp of a ship at rough sea”. It presents results of computer simulations of motion of a rescue module with embarked persons during its launching on rollers along stern ramp of a ship at rough sea. The simulations were conducted for a selected ship fitted with a launching ramp , for...
-
Strategies for computationally feasible multi-objective simulation-driven design of compact RF/microwave components
PublikacjaMulti-objective optimization is indispensable when possible trade-offs between various (and usually conflicting) design objectives are to be found. Identification of such design alternatives becomes very challenging when performance evaluation of the structure/system at hand is computationally expensive. Compact RF and microwave components are representative examples of such a situation: due to highly compressed layouts and considerable...
-
Structural and dynamic changes adopted by EmrE, multidrug transporter protein—Studies by molecular dynamics simulation
PublikacjaEmrE protein transports positively charged aromatic drugs (xenobiotics) in exchange for two protons and thus provides bacteria resistance to variety of drugs. In order to understand how this protein may recognize ligands, the monomer and asymmetric apo-form of the EmrE dimer embedded in a heterogeneous phospholipid (POPE + POPG) membrane were studied by molecular dynamics simulations. Dimer is regarded as a functional form of the...
-
Simulation of Direct-Sequence Spread Spectrum Data Transmission System for Reliable Underwater Acoustic Communications
PublikacjaUnderwater acoustic communication (UAC) system designers tend to transmit as much information as possible, per unit of time, at as low as possible error rate. It is a particularly difficult task in a shallow underwater channel in which the signal suffers from strong time dispersion due to multipath propagation and refraction phenomena. The direct-sequence spread spectrum technique (DSSS) applied successfully in the latest standards...
-
On low-fidelity models for variable-fidelity simulation-driven design optimization of compact wideband antennas
PublikacjaThe paper addresses simulation-driven design optimization of compact antennas involving variable-fidelity electromagnetic (EM) simulation models. Comprehensive investigations are carried out concerning selection of the coarse model discretization density. The effects of the low-fidelity model setup on the reliability and computational complexity of the optimization process are determined using a benchmark set of three ultra-wideband...
-
Computational model for simulation of lifeboat motions during its launching from ship in rough seas
PublikacjaW artykule przedstawiono model obliczeniowy 3 D, opisujący ruch obiektu w 6 stopniach swobody (6DoF), do symulacji ruchu jedno- lub dwuzawiesiowej łodzi ratunkowej lub ratowniczej podczas opuszczania ze statku na wzburzonej wodzie. Jest to złożony model uwzględniający warunki morskie oraz elastyczność i własności tłumiące elementów i mechanizmów żurawika, liny oraz kadłuba łodzi. Ponadto przedstawiono przykładowe wyniki obliczeń...
-
Bitumen Aging—Laboratory Simulation Methods Used in Practice and Selected Directions of Research on New Methods
PublikacjaChanges in the properties of bitumen binders that occur as a result of aging have a huge impact on the durability of products produced from them. In particular, asphalt pavements, which constitute the most common use of petroleum bitumen, are susceptible to damage resulting from the increasing stiffness of the bitumen during its life cycle. Increased stiffness of asphalt pavements reduces the pavement resistance to low-temperature...
-
Simulation of fluid structure interaction in a novel design of high pressure axial piston hydraulic pump
PublikacjaA novel type of an axial, piston-driven high pressure hydraulic pump with variable capacity marks a significant improvement in the area of the hydraulic machinery design. Total discharge from hydrostatic forces eliminates a need for a servomechanism, thus simplifying operation, reducing weight and introducing the possibility of the pump displacement control by computer. PWK-type pumps, invented in the Gdansk University of Technology,...
-
Simulation Studies of Control Systems for Doubly Fed Induction Generator Supplied by the Current Source Converter
PublikacjaThe control system for a Doubly Fed Induction Generator (DFIG) supplied by a grid-connected Current Source Converter (CSC) is presented in this paper. Nonlinear transformation of DFIG model to the multi-scalar form is proposed. The nonlinear control strategy of active and reactive power of DFIG is realized by feedback linearization. In the proposed control scheme, the DFIG model and CSI parameters are included. Two Proportional-Integral...
-
Cost-Efficient EM-Driven Size Reduction of Antenna Structures by Multi-Fidelity Simulation Models
PublikacjaDesign of antenna systems for emerging application areas such as the Internet of Things (IoT), fifth generation wireless communications (5G), or remote sensing, is a challenging endeavor. In addition to meeting stringent performance specifications concerning electrical and field properties, the structure has to maintain small physical dimensions. The latter normally requires searching for trade-off solutions because miniaturization...
-
Encapsulation of an anticancer drug Isatin inside a host nano-vehicle SWCNT: a molecular dynamics simulation
PublikacjaThe use of carbon nanotubes as anticancer drug delivery cargo systems is a promising modality as they are able to perforate cellular membranes and transport the carried therapeutic molecules into the cellular components. Our work describes the encapsulation process of a common anticancer drug, Isatin (1H-indole-2,3-dione) as a guest molecule, in a capped single-walled carbon nanotube (SWCNT) host with chirality of (10,10). The...
-
Computational Simulation of the Effects of Different Culture Types and Leader Qualities on Mistake Handling and Organisational Learning
PublikacjaThis chapter investigates computationally the following research hypotheses: (1) Higher flexibility and discretion in organisational culture results in better mistake management and thus better organisational learning, (2) Effective organisational learning requires a transformational leader to have both high social and formal status and consistency, and (3) Company culture and leader’s behavior must align for the best learning...
-
Numerical simulation of the influence of the selected factors on the performance of a concrete road barrier H2/W5/B
PublikacjaThis paper discuss the influence of selected factors on the performance of a concrete road barrier H2/W5/B. Modelling techniques of a concrete road safety system were briefly discussed. Comparison to the full scale crash test results has been shown. The concrete road safety barrier has been investigated for evaluation of the overall damage after collision under various initial conditions. The failure assessment criterion has been...
-
Parameter and delay estimation of linear continuous-time systems
PublikacjaIn this paper the problem of on-line identification of non-stationary delay systems is considered. Dynamics of supervised industrial processes is usually described by ordinary differential equations. Discrete-time mechanization of their continuous-time representations is based on dedicated finite-horizon integrating filters. Least-squares and instrumental variable procedures implemented in recursive forms are applied for simultaneous...
-
Multi-Transformer Flyback Converter for Supplying Isolated IGBT and MOSFET Drivers
PublikacjaA multi transformer flyback converter topology for supplying transistor drivers is presented. The topology presents some advantages over typical multi output single transformer, as reduction of effective leakage inductance, equal magnetic coupling between primary and secondary circuits and better isolation between outputs. Simulation study carried out in the LTSpice IV program and preliminary experimental results indicate high...
-
Comparative Analysis of Salient and Non-Salient Pole Brushless Synchronous Generator for Application in Autonomous Electric Power System
PublikacjaThis paper presents a comparative study of two types of brushless synchronous generator for application in autonomous electric power systems (e.g. airplane power grid). Commercially used salient pole and a prototype non-salient pole high speed multi-pole brushless synchronous generator (BSG) have been presented. Comparative analysis of both types of the generator has been performed. Chosen simulation (using FEM and circuit models)...
-
On–line Parameter and Delay Estimation of Continuous–Time Dynamic Systems
PublikacjaThe problem of on-line identification of non-stationary delay systems is considered. The dynamics of supervised industrial processes are usually modeled by ordinary differential equations. Discrete-time mechanizations of continuous-time process models are implemented with the use of dedicated finite-horizon integrating filters. Least-squares and instrumental variable procedures mechanized in recursive forms are applied for simultaneous...
-
Accurate modeling of quasi-resonant inverter fed IM drive
PublikacjaIn this paper wide-band modeling methodology of a parallel quasi-resonant dc link inverter (PQRDCLI) fed induction machine (IM) is presented. The modeling objective is early-design stage prediction of conductive electromagnetic interference (EMI) emissions of the considered converter fed IM drive system. Operation principles of the selected topology of PQRDCLI feeding IM drive are given. Modeling of the converter drive system is...
-
Improving SBR Performance Alongside with Cost Reduction through Optimizing Biological Processes and Dissolved Oxygen Concentration Trajectory
PublikacjaAuthors of this paper take under investigation the optimization of biological processes during the wastewater treatment in sequencing batch reactor (SBR) plant. A designed optimizing supervisory controller generates the dissolved oxygen (DO) trajectory for the lower level parts of the hierarchical control system. Proper adjustment of this element has an essential impact on the efficiency of the wastewater treatment process as well...
-
Identification of Unstable Reference Points and Estimation of Displacements Using Squared Msplit Estimation
PublikacjaThe article presents a new version of the method for estimating parameters in a split functional model, which enables the determination of displacements of geodetic network points with constrained datum. The main aim of the study is to present theoretical foundations of Msplit CD estimation and its basic properties and possible applications. Particular attention was paid to the efficacy of the method in the context of geodetic...
-
Analysis of passenger car crash with a cable barrier installed with anti-glare screens on a horizontal convex road curve with 400 m radius
PublikacjaHigh-tension cable barriers have been used on roads for a relatively short period compared with other types of road barriers. Hence, there remains a need for further research on various crash scenarios. An important issue is the performance of a cable barrier on a road curve, particularly when a vehicle impacts the convex side of the barrier. To address this issue, the analysis in this study considers a system of anti-glare screens...
-
Central heating temperature control algorithm for systems with condensing boilers
PublikacjaThe problem of control of a central heating system in a small residence is considered. It is assumed that the system is based on a condensing boiler. Since the boiler efficiency depends on a returning water temperature, the proposed control goal is to provide proper air temperature in the residence as well as the lowest possible water temperature. The proposed algorithm is applied to two buildings. Both of them have the same heating...
-
Numerical modeling of sound intensity distributions around acoustic transducer
PublikacjaThe aim of this research study is to measure, simulate and compare sound intensity distribution generated by the acoustic transducers of the loudspeaker. The comparison of the gathered data allows for validating the numerical model of the acoustic radiation. An accurate model of a sound source is necessary in mathematical modeling of the sound field distribution near the scattering obstacles. An example of such obstacle is a human...
-
Evaluation of electrical parameters of traction supply system for complex railway traffic conditions, using simulation methods
PublikacjaDevelopment of electrified transport systems, railways modernization, expansion of urban transport networks, purchases of modern rolling stock causes that updating of electric traction supply system is necessary. This chapter presents an effective method for electrical parameters of traction supply system evaluation, using simulation methods.
-
Simulation of unsteady flow over floodplain using the diffusive wave equation and the modified finite element method
PublikacjaWe consider solution of 2D nonlinear diffusive wave equation in a domain temporarily covered by a layer of water. A modified finite element method with triangular elements and linear shape functions is used for spatial discretization. The proposed modification refers to the procedure of spatial integration and leads to a more general algorithm involving a weighting parameter. The standard finite element method and the finite difference...
-
Component Based Flight Simulation in DIS Systems.Komponentowy model symulacji obiektów latających w systemach DIS.
PublikacjaInteraktywna symulacja rozproszona stanowi interesującą klasę systemów informacyjnych łączących kilka dziedzin informatyki pozwalających każdemu obiektowi na indywidualne symulowanie dla wizualizacji dynamicznego stanu wszystkich uczestniczących w symulacji obiektów rozproszonych. Obiekty są nieprzewidywalne, z tego powodu istnieje konieczność ciągłej wymiany informacji o ich stanie na potrzeby poprawnej wizualizacji 3D sceny z...
-
Efficient Simulation-Based Global Antenna Optimization Using Characteristic Point Method and Nature-Inspired Metaheuristics
PublikacjaAntenna structures are designed nowadays to fulfil rigorous demands, including multi-band operation, where the center frequencies need to be precisely allocated at the assumed targets while improving other features, such as impedance matching. Achieving this requires simultaneous optimization of antenna geometry parameters. When considering multimodal problems or if a reasonable initial design is not at hand, one needs to rely...
-
Lax-Wendroff and McCormack Schemes for Numerical Simulation of Unsteady Gradually and Rapidly Varied Open Channel Flow
PublikacjaTwo explicit schemes of the finite difference method are presented and analyzed in the paper. The applicability of the Lax-Wendroff and McCormack schemes for modeling unsteady rapidly and gradually varied open channel flow is investigated. For simulation of the transcritical flow the original and improved McCormack scheme is used. The schemes are used for numerical solution of one dimensional Saint-Venant equations describing free...
-
Atomistic Surrogate-Based Optimization for Simulation-Driven Design of Computationally Expensive Microwave Circuits with Compact Footprints
PublikacjaA robust simulation-driven design methodology for computationally expensive microwave circuits with compact footprints has been presented. The general method introduced in this chapter is suitable for a wide class of N-port un-conventional microwave circuits constructed as a deviation from classic design solutions. Conventional electromagnetic (EM) simulation-driven design routines are generally prohibitive when applied to numerically...
-
Verification of geotechnical numerical simulations by model tests using PIV technique. Part II Numerical Simulation
PublikacjaPrzedstawiono zakres i wyniki symulacji numerycznych stateczności fundamentów bezpośrednich posadowionych w sąsiedztwie kątowych ścian oporowych. Wyniki symulacji numerycznych zweryfikowano na podstawie wyników badań modelowych z uwzględnieniem techniki PIV przedstawionych w części I niniejszego artykułu. W obliczeniach numerycznych wykorzystano trzy kryteria wytrzymałości gruntu na ścinanie: Coulomba - Mohra, Matsuoki - Nokaiego...
-
Electrochemical simulation of metabolism for antitumor-active imidazoacridinone C-1311 and in silico prediction of drug metabolic reactions
PublikacjaThe metabolism of antitumor-active 5-diethylaminoethylamino-8-hydroxyimidazoacridinone (C-1311) has been investigated widely over the last decade but some aspects of molecular mechanisms of its metabolic transformation are still not explained. In the current work, we have reported a direct and rapid analytical tool for better prediction of C-1311 metabolism which is based on electrochemistry (EC) coupled on-line with electrospray...
-
Operation of the Hybrid Photovoltaic-Battery System on the Electricity Market—Simulation, Real-Time Tests and Cost Analysis
PublikacjaThis paper presents research on a hybrid photovoltaic-battery energy storage system, declaring its hourly production levels as a member of a balancing group submitting common scheduling unit to the day-ahead market. It also discusses the variability of photovoltaic system generation and energy storage response. The major research questions were whether the operation of a hybrid photovoltaic-battery energy storage system is viable...
-
Modeling, simulation, and validation of a TB41 crash test of the H2/W5/B concrete vehicle restraint system
PublikacjaThe paper addresses numerical simulations of a concrete vehicle restraint system. The model is described in detail. The advanced material law of the continuous surface cap model was used to analyze the damage locations in concrete barrier segments. The results were validated against the TB41 full-scale crash test. The test was conducted in compliance with European standard EN 1317, and the validation was performed in accordance...
-
Rapid simulation-driven design of miniaturised dual-band microwave couplers by means of adaptive response scaling
PublikacjaOne of the major challenges in the design of compact microwave structures is the necessity of simultaneous handling of several objectives and the fact that expensive electromagnetic (EM) analysis is required for their reliable evaluation. Design of multi-band circuits where performance requirements are to be satisfied for several frequencies at the same time is even more difficult. In this work, a computationally efficient design...
-
Efficient parallel implementation of crowd simulation using a hybrid CPU+GPU high performance computing system
PublikacjaIn the paper we present a modern efficient parallel OpenMP+CUDA implementation of crowd simulation for hybrid CPU+GPU systems and demonstrate its higher performance over CPU-only and GPU-only implementations for several problem sizes including 10 000, 50 000, 100 000, 500 000 and 1 000 000 agents. We show how performance varies for various tile sizes and what CPU–GPU load balancing settings shall be preferred for various domain...
-
Assessment of the Speed Management Impact on Road Traffic Safety on the Sections of Motorways and Expressways Using Simulation Methods
PublikacjaMethods used to evaluate the impact of Intelligent Transport System (ITS) services on road safety are usually based on expert assessments or statistical studies. However, commonly used methods are challenging to apply in the planning process of ITS services. This paper presents the methodology of research using surrogate safety measures calculated and calibrated with the use of simulation techniques and a driving simulator. This...
-
Computational fluid dynamics simulation of heat transfer from densely packed gold nanoparticles to isotropic media
PublikacjaThis work aims to determine and compare heat generation and propagation of densely packed gold nanoparticles (Au NPs) induced by a resonant laser beam (532 nm) according to the Mie theory. The heat flux propagation is transferred into the materials, which here are: silica glass; soda-lime-silica glass; borosilicate glass; polymethyl methacrylate (PMMA); polycarbonate (PC); and polydimetylosiloxane (PDMS). This analysis aims to...
-
Globalized Knowledge-Based Simulation-Driven Antenna Miniaturization Using Domain-Confined Surrogates and Dimensionality Reduction
PublikacjaDesign of contemporary antenna systems encounters multifold challenges, one of which is a limited size. Compact antennas are indispensable for the new fields of application such as inter-net of things or 5G/6G mobile communication. Still, miniaturization generally undermines elec-trical and field performance. When attempted through numerical optimization, it turns into a constrained problem with costly constraints requiring electromagnetic...
-
Low-Cost Quasi-Global Optimization of Expensive Electromagnetic Simulation Models by Inverse Surrogates and Response Features
PublikacjaConceptual design of contemporary high-frequency structures is typically followed by a careful tuning of their parameters, predominantly the geometry ones. The process aims at improving the relevant performance figures, and may be quite expensive. The reason is that conventional design methods, e.g., based on analytical or equivalent network models, often only yield rough initial designs. This is especially the case for miniaturized...
-
Modular power converter with superconducting magnetic energy storage for electric power distribution system — Analysis and simulation
PublikacjaThis paper describes selected issues concerning realization of energy storage system (ESS) designed to operate in power distribution system. This paper presents a modular approach of 300 kVA power converter operating with superconducting magnetic energy storage (SMES), which gives high dynamics together with high power and suitable capability for instantaneous energy storage. Analysis and simulation studies of selected power converter...
-
Energy Consumption Modeling in SPMD and DAC Applications
PublikacjaIn this chapter, we show a study of energy consumption during execution of SPMD and DAC application – the same applications which time of execution we modeled in the previous two chapters. We measured an average power usage at a single node of the GALERA+ cluster during application execution and then we modeled the total energy consumption by the application. Next we simulated the applications using MERPSYS and we compared the...
-
Analysis the Parameters of the Adaptive Controller for Quality Control of Dissolved Oxygen Concentration
PublikacjaThe wastewater treatment plant can be considered a dynamic large scale complex system, in which the most important control parameter is the dissolved oxygen concentration in the aerobic zone. The air is supplied to this zone by the aeration system. In the paper, both the sequencing batch reactor and the aeration system are modelled and used as plant of control performed by the cascade nonlinear adaptive control system extended...
-
Supervisory fuzzy control system for biological processes in sequencing wastewater batch reactor
PublikacjaThe paper proposes the design of the supervisory heuristic fuzzy control system applied to a Sequencing Batch Reactor (SBR) in the Wastewater Treatment Plant (WWTP). Based on real data records and the biological process and aeration system models, a control system for biological processes has been designed. The supervisory control system performs management of the reactor work cycle, determines the phase length, controls the sludge...
-
Comparative Study of Integer and Non-Integer Order Models of Synchronous Generator
PublikacjaThis article presents a comparison between integer and non-integer order modelling of a synchronous generator, in the frequency domain as well as in the time domain. The classical integer order model was compared to one containing half -order systems. The half-order systems are represented in a Park d-q axis equivalent circuit as impedances modelled by half-order transmittances. Using a direct method based on the approximation...
-
On implementation of fibrous connective tissues’ damage in Abaqus software
PublikacjaConnective fibrous tissues, such as tendons and ligaments, in humans and animals exhibit hyperelastic behaviour. The constitution of the material of these tissues is anisotropic due to the presence of the collagen fibres, where one family of fibres is the typical case. Traumatic events and/or aging may sometimes lead to the damage of the tissue. The study of motion of affected joints or limbs is usually not permitted in vivo. This...