Filtry
wszystkich: 1522
wybranych: 1141
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: CYCLIC PLASTIC BEHAVIOUR
-
Enhanced coupled elasto-plastic-damage models to describe concrete behaviour in cyclic laboratory tests: comparison and improvement.
PublikacjaArtykuł omawia różne modele połączone sprężysto-plastyczne z degradacją sztywności do opisu zachowania się betonu pod obciążeniem cyklicznym. Modele zostały rozszerzone o długość charakterystyczną mikrostruktury w do opisu lokalizacji odkształceń. Wykonano obliczenia MES dla ściskania i zginania. Zaproponowano własny ulepszony model.
-
Cyclic behaviour modelling of additively manufactured Ti-6Al-4V lattice structures
PublikacjaThe present work is concerned with the numerical modelling of the cyclic behaviour of Ti-6Al-4V lattice structures. In the study, diamond structures of titanium alloy produced by the additive laser powder bed fusion (LPBF) method with different degrees of relative density were used. Realistic geometric models of the studied mesostructures were generated using computed microtomography, taking into account the imperfections of the...
-
Strain-dependent behaviour of cold recycled material mixtures in cyclic compression tests
PublikacjaThe purpose of the study is to evaluate strain-dependent behaviour of Cold Recycled Material (CRM) mixtures using three frameworks typically applied for Hot Mix Asphalt (HMA): linear viscoelastic (LVE) limits; non-linearity directions; changes in rheological model parameters. To this aim, the complex modulus of three CRM mixtures with different bitumen-to-cement ratio (0.2, 0.6 and 1.8) was measured in cyclic compression mode,...
-
Combining tight-binding and molecular dynamics methods to model the behaviour of metals in the plastic regime
PublikacjaOpisujemy zastosowanie metody dwuskalowej (kwantowo-klasycznej) w zastosowaniu do metali. Region energetycznie najważniejszy jest traktowany kwantowo, podczas gdy reszta układu jest traktowana klasycznie. Wprowadzamy własną implementację metody oraz przedstawiamy uzyskane wyniki dla metali.
-
Effect of austempering temperature on microstructure and cyclic deformation behaviour of multiphase low-carbon steel
PublikacjaThis paper examined the cyclic deformation behaviour of multiphase low-carbon steel that was subjected to austempering heat treatments at four temperatures (190 °C, 230 °C, 275 °C, and 315 °C) below the martensite start temperature (Ms = 353 °C). The tests were conducted at room temperature, under fully reversed strain-controlled conditions, with strain amplitudes in the range 0.5–1.0%. The microstructure was observed by transmission...
-
Behaviour of asphalt concrete in cyclic and static compression creep test with and without lateral confinement
PublikacjaArtykuł przedstawia wpływ metodyki badań na określanie parametrów betonu asfaltowego. Wykazano, że badania pełzania bez skrępowania bocznego w większym stopniu uwypuklają wpływ asfaltu na parametry badanego betonu asfaltowego natomiast w badaniach ze skrępowaniem bocznym, zarówno rola asfaltu jak i szkieletu mineralnego jest uwzględniana przy ocenie parametrów betonu asfaltowego. Ponadto wykazano, że lepszymi miarami do oceny betonu...
-
Application of enhanced elasto-plastic damage models to concrete under quasi-static and dynamic cyclic loading
PublikacjaArtykuł omawia wyniki symulacji zachowania sie elementów betonowych poddanych zginaniu w czasie cyklicznego obciążenia. Do symulacji zastosowano 3 połączone modele sprężysto-plastyczne z degradacją sztywności i z nielokalnym osłabieniem. Wyniki symulacji porównano bezpośrednio z doświadczeniami.
-
An elasto-plastic constitutive model with non-local softening and viscosity to describe dynamic concrete behaviour.
PublikacjaW artykule zaproponowano model do opisu betonu podczas dynamicznego obciążenia. Przyjęto model sprężysto-plastyczny z degradacją sztywności i nielokalnym osłabieniem rozszerzony o lepkość. Obliczenia MES dla elementów betonowych pod obciążeniem dynamicznym o różnej prędkości obciążenia porównano z doświadczeniami.
-
Cyclic deformation and fracture behaviour of additive manufactured maraging steel under variable-amplitude loading
PublikacjaThe cyclic deformation and fracture behaviour of 18Ni300 maraging steel produced by laser beam powder bed fusion is studied under variable-amplitude loading. The tests were conducted under fully-reversed strain-controlled conditions with a loading sequence comprising three ascending cycles and three descending cycles repeated sequentially until failure. After the tests, fracture surfaces were examined using height and volume surface...
-
Electrochemical behaviour of Cr coating in acidic sulphate solution studied by cyclic polarization and impedance spectroscopy
PublikacjaOdporność korozyjną powłok chromowych w 0.01 M H2SO4 zbadano metodami woltamperometrii cyklicznej i spektroskopii impedancyjnej. Stwierdzono, że właściwości ochronne powłoki chromowej w kontakcie z powietrzem wzrastają dzięki tworzeniu się warstwy tlenkowej zapełniającej defekty w powłoce. W trakcie polaryzacji anodowej następuje częściowe roztwarzanie tej warstwy i penetracja agresywnego środowiska do podłoża (stali), co powoduje...
-
Analysis of concrete behaviour under cycling within coupled elasto-plastic-damage with non-local softening
PublikacjaArtykuł omawia wyniki symulacji zachowania sie elementów betonowych poddanych cyklicznemu obciążeniu. Do symulacji zastosowano 3 połączone modele sprężysto-plastyczne z degradacją sztywności i z nielokalnym osłabieniem. Wyniki symulacji porównano z doświadczeniami laboratoryjnymi..
-
Orientation effects on the fracture behaviour of additively manufactured stainless steel 316L subjected to high cyclic fatigue
PublikacjaIn this paper, stainless steel 316L (SS316L) bars were additively manufactured (AM) in three orientations (Z – vertical, XY – horizontal, ZX45 – midway between vertical and horizontal) by using the Laser Powder Bed Fusion Melting (LPBF-M) method. The AM specimens were subjected to load control fatigue testing under full tension and compression (R = -1) at stress amplitudes ±350, ±400 and ±450 MPa. The XY and ZX45 printing orientations...
-
Coupled elasto-plastic-damage model with non-local softening enhanced by viscosity to describe dynamic concrete behaviour
PublikacjaW artykule zaproponowano model do opisu betonu podczas dynamicznego obciążenia. Przyjęto model sprężysto-plastyczny z degradacją sztywności i nielokalnym osłabieniem rozszerzony o lepkość. Obliczenia MES dla elementów betonowych pod obciążeniem dynamicznym o różnej prędkości obciążenia porównano z doświadczeniami.
-
Sustainable synthesis of cyclic carbonates from bio‐based polyether polyol: the structure characterization, rheological behaviour and thermal properties
PublikacjaThe cycloaddition of CO2 to epoxides represents a green efficient method to form bis(cyclic carbonate)s. The main purpose of the work reported in this paper was to examine the effect of the gas flow rate (20, 40, 60 and 100 mL min–1) during carbonation on the conversion yield, chemical structure, rheological behaviour and thermal properties of the prepared compounds. A series of new bis(cyclic carbonate)s was obtained from bio‐based...
-
Computational simulations of concrete behaviour under dynamic conditions using elasto-visco-plastic model with non-local softening
Publikacja -
Computational simulations of concrete behaviour under dynamic conditions using elasto-visco-plastic model with non-local softening.
PublikacjaW artykule przedstawiono wyniki obliczeniowych symulacji zachowania betonu w warunkach dynamicznych stosując sprężysto-lepko-plastyczny model z nielokalnym osłabieniem. Wykonano obliczenia dla ściskania jednoosiowego, rozciągania jednoosiowego i zginania. Dla dużych prędkości obciążenia uwzględniono fragmentację materiału. Wyniki porównano z doswiadczeniami.
-
Finite element investigations of granular material behaviour during cyclic wall shearing under a constant normal stiffness condition
PublikacjaW artykule przedstawiono wyniki numnerycznej analizy zachowania sie materiałów granulowanych podczas cyklicznego ścinanai wzdłuz szorstkiej ściany z warunkiem stałej sztywności normalnej. Obliczenia wykonano przy zastosowaniu metody elementów skończonych i mikropolarnego nodelu hipopalstycznego. Obliczenia wykonano dla róznych sztywności, początkowych wskaźników porowatości i sredniej średnicy ziarna. Wyniki numeryczne porównano...
-
Effect of processing parameters on the cyclic behaviour of aluminium friction stir welded to spark plasma sintered aluminium matrix composites with bimodal micro-and nano-sized reinforcing alumina particles
PublikacjaUnderstanding the cyclic behaviour of Alumina reinforced Aluminium composites (Al-A2O3) was of critical importance, for their further application in the different industrial sectors. The present study is focussing on the cyclic behaviour of the Al-Alumina nanocomposite produced through the combination of spark plasma sintering (SPS) method and friction stir welding (FSW). The added Alumina with total content of 10% is the combination...
-
A continual model of a damaged medium used for analyzing fatigue life of polycrystalline structural alloys under thermal–mechanical loading
PublikacjaThe main physical laws of thermal–plastic deformation and fatigue damage accumulation processes in polycrystalline structural alloys under various regimes of cyclic thermal–mechanical loading are considered. Within the framework of mechanics of damaged media, a mathematical model is developed that describes thermal–plastic deformation and fatigue damage accumulation processes under low-cycle loading. The model consists of three...
-
Rigid finite elements and multibody modeling in analyses of a robot shaped elastic/plastic deformations of a beam
PublikacjaDynamics analysis of a system composed of a parallel manipulator and of an elastic beam is presented in the paper. Classic 3RRR parallel manipulator is considered and used to deform the beam. Elasto-plastic deformations are investigated. Rigid-finite-elements technique is employed to deal with dynamics of the beam. A multibody structure is associated with the introduced hybrid system in order to model its dynamics. Idea of the...
-
On modelling and non-linear elasto-plastic analysis of thin shells with deformable junctions
PublikacjaThe undeformed base surface of the irregular thin shell is modelled by the union of a finite number of regular smooth surface elements joined together along spatial curvilinear surface edges. The equilibrium conditions are formulated by postulating an appropriate form of the principle of virtual work, where also deformability of shell junctions is taken into account. The PVW is then discretised by C1 finite elements and the incremental-iterative...
-
Experimental study on the behaviour of steel columns under seismic-induced axial impact load
PublikacjaIt has been observed during major earthquakes that the so called soft-storey failure of an upper floor of a structure results in large impact load acting on structural members of the lower storeys. It may further lead to progressive collapse of the whole structure substantially intensifying human and material losses. Therefore, the aim of this paper is to investigate experimentally the behaviour of columns under bending (observed...
-
Numerical Modelling of Connections Between Stones in Foundations of Historical Buildings
PublikacjaThe aim of this paper is to analyse the behaviour of old building foundations composed of stones (the main load-bearing elements) and mortar, based on numerical analysis. Some basic aspects of historical foundations are briefly discussed, with an emphasis on their development, techniques, and material. The behaviour of a foundation subjected to the loads transmitted from the upper parts of the structure is described...
-
Experimental tests for the determination of mechanical properties of PVC foil
PublikacjaThe paper presents an application of the PVC film in civil engineering. Mechanical behaviour of the PVC film applied for suspended ceilings, in the form of a stretch ceiling is investigated under uniaxial and biaxial tensile tests. The study is focused on the determination of mechanical properties from experimental data (uniaxial and biaxial tensile tests). The uniaxial cyclic tests are performed in order to observe a variation...
-
Modelling reinforced concrete beams under mixed shear-tension failure with different continuous FE approaches
PublikacjaThe paper presents quasi-static numerical simulations of the behaviour of short reinforced concrete beams without shear reinforcement under mixed shear-tension failure using the FEM and four various constitutive continuum models for concrete. First, an isotropic elasto-plastic model with a Drucker-Prager criterion defined in compression and with a Rankine criterion defined in tension was used. Next, an anisotropic smeared crack...
-
Modelling tunnelling-induced deformation in stiff soils with a hyperelastic–plastic anisotropic model
PublikacjaIn this paper, the tunnelling-induced deformation in anisotropic stiff soils is analysed using FE modelling. The influence of material description is investigated rather than an advanced simulation of the tunnelling method. A new hyperelastic– plastic model is proposed to describe the anisotropic mechanical behaviour of stiff highly overconsolidated soil. This model can reproduce the superposition of variable stress-induced anisotropy...
-
Study on deformed steel columns subjected to impact load due to soft-storey failure in buildings during earthquakes
PublikacjaThe so called soft-storey failure is one of the most typical types of damage induced in buildings as the result of earthquake excitation. It has been observed during ground motions that the failure of an upper soft storey of a structure results in large vertical impact load acting on the lower floors. If the resistance of the structural members of the lower storeys is not sufficient it may further lead to progressive collapse of...
-
Behaviour of deformed steel columns exposed to impact load during earthquakes - experimental study
PublikacjaIt has been observed during major earthquakes that the so called soft-storey failure of an upper floor of a structure results in large impact load acting on structural members of the lower storeys. It may further lead to progressive collapse of the whole structure substantially intensifying human and material losses. The aim of this paper is to investigate experimentally the behaviour of horizontally deformed columns (deformation...
-
SOLUTIONS OF THE INTERMEDIATE SUPPORT STRUC- TURES OF THE NORTHERN MARMARA HIGHWAY (ISTAN- BUL’S RING ROAD) IN THE CONTEXT OF SEISMIC ACTIVITY
PublikacjaIn 2014–2018, as a result of the expansion of the city of Istanbul in Turkey, a project was imple- mented consisting of building a northern ring road, called the Northern Marmara Highway. The concept of the structural design of the ring road’s intermediate supports aims at constructing sup- ports that according to the TURKISH DLH 2008 standard must comply with the design require- ments for the three calculated earthquake insensitivity...
-
Material characterisation of biaxial glass-fibre non-crimp fabrics as a function of ply orientation, stitch pattern, stitch length and stitch tension
PublikacjaDue to their high density-specific stiffnesses and strength, fibre reinforced plastic (FRP) composites are particularly interesting for mobility and transport applications. Warp-knitted non-crimp fabrics (NCF) are one possible way to produce such FRP composites. They are advantageous because of their low production costs and the ability to tailor the properties of the textile to the reinforcement and drape requirements of the application....
-
Acoustic Hysteresis in Flows with Different Kinds of Relaxation and Attenuation
PublikacjaGraphs in the thermodynamic plane acoustic pressure versus excess acoustic density representing acoustic hysteresis, are considered as indicators of relaxation processes, equilibrium parameters of a flow, and kinds of wave exciters. Some flows with deviation from adiabaticity are examined: the Newtonian flow of a thermocon- ducting gas, the flow of a gas with vibrational relaxation, the flow of liquid electrolyte with a chemical...
-
The effect of elevated temperature on LCF damage growth in 2024AA – Experiment and modeling
PublikacjaThis paper presents the results of experimental low-cycle fatigue (LCF) tests conducted on EN-AW 2024 alloy in T3511 temper at 100 ◦C, 200 ◦C and 300 ◦C. The material’s basic fatigue characteristics were determined, such as fatigue life curve and cyclic strain curve. Both the hysteresis loop and nature of fracture surfaces obtained in macro- and microscopic observations (scanning electron microscope, SEM) were accounted for. The...
-
High temperature corrosion resistance of porous hastelloy alloy
PublikacjaTo further understand the suitability of Ni-Cr-base alloy for solid oxide fuel cell (SOFC), a commercial Ni-Cr-Fe-Mo alloy, Hastelloy X was selected and evaluated for oxidation behaviour under high temperature conditions. HastelloyX was chosen due to its unusual resistance to oxidizing, reducing and neutral atmospheres. For long term stability of metal supported fuel cell, the corrosion resistance plays a vital role and must be...
-
Preparation, morphology and properties of natural rubber composites filled with untreated short jute fibres
PublikacjaGreen composites were obtained by incorporation of short jute fibres in natural rubber matrix using a laboratory two-roll mill. The influence of untreated fibre content (1, 2.5, 5, 7.5 and 10 phr) on the mechanical properties, dynamic mechanical properties, swelling properties was examined. The behaviour of prepared green composites under cyclic compression was also investigated. Fibre dispersion in rubber matrix was studied by...
-
LCF behavior of 2024AA under uni- and biaxial loading taking into account creep pre-deformation
PublikacjaThis study presents the results of experimental low-cycle fatigue (LCF) tests of aluminum 2024 alloy T3511 temper in uni- and biaxial loading states. Tests were carried out on both the as-received material (hardened extruded rods) and material with different pre-deformation histories. These deformations were carried out in the creep process at 200 °C and 300 °C for two different levels of at each temperature. The pre-deformed material’s...
-
Estimation of Stresses in a Dry Sand Layer Tested on Shaking Table
PublikacjaTheoretical analysis of shaking table experiments, simulating earthquake response of a dry sand layer, is presented. The aim of such experiments is to study seismic-induced compaction of soil and resulting settlements. In order to determine the soil compaction, the cyclic stresses and strains should be calculated first. These stresses are caused by the cyclic horizontal acceleration at the base of soil layer, so it is important...
-
FEM modelling of stress and strain distribution in weld joints of steel sandwich panels
PublikacjaThe development of laser welding technology has enabled the mass production of thin-walled structures, including steel sandwich panels. The technology of joining plating panels with stiffeners by welding allows us to create joints with a specific geometry and material properties. In comparison with other types of joints, laser welds are characterized by their specific behaviour under cyclic load and, as a consequence, a different...
-
Investigation of natural frequencies of axially loaded thin-walled columns
PublikacjaThe paper deals with correlation between natural frequencies of two steel thin-walled columns and the corresponding applied load. The structures are made of cold-formed lipped channel sections. The columns lengths were assumed to follow two buckling patterns – global flexural and flexural-torsional buckling. In the thicker structure two material models were considered – linearly-elastic and elastic-perfectly plastic. Numerical...
-
A novel approach in wood waste utilization for manufacturing of catalyst-free polyurethane-wood composites (PU-WC)
PublikacjaIn recent decades, due to the increase in environmental awareness and noticeable environmental degradation, the area of wood waste management has attracted increasing attention. The purpose of this study is to develop a new type of highly filled polyurethane wood-composite (PU-WC) by the utilization of large amount of wood wastes without addition of a catalyst. Although wood-plastic composites (WPCs) are widely known, there is...
-
NON-LOCAL VOLUMETRIC APPROACH TO ANALYSIS DEFECT'S SHAPE INFLUENCE ON SPECIMENS DURABILITY SUBJECTED TO BENDING AND TORSION
PublikacjaThe influence of defect features on fatigue behaviour is a complex trivial issue. Although the important advances over the last decades, the dialectical relationship between the defect orientation and durability is not clearly understood. The paper aims at studying the influence of the orientation of elliptical defects on the durability of samples made of C45 steel. Three types of samples with elliptical defects were subjected...
-
Refinement of the Hardening Soil model within the small strain range
PublikacjaThe popularity of the elasto-plastic Hardening Soil (HS) model is based on simple parameter identification from standard testing and empirical formulas. The HS model is implemented in many commercial FE codes designed to analyse geotechnical problems. In its basic version, the stress–strain behaviour within the elastic range is subject to the hypoelastic power law, which assures the barotropy of the elastic stiffness. However,...
-
On some problems in determining tensile parameters of concrete model from size effect tests
PublikacjaThe paper presents results of numerical simulations of size effect phenomenon in concrete specimens. The behaviour of in-plane geometrically similar notched and unnotched beams under three-point bending is investigated. In total 18 beams are analysed. Concrete beams of four different sizes and five different notch to depth ratios are simulated. Two methods are applied to describe cracks. First, an elasto-plastic constitutive law...
-
Influence of soil anisotropic stiffness on the deformation induced by an open pit excavation.
PublikacjaIn this paper, the problem of deformation induced by an open pit excavation in anisotropic stiff soils is analysed by FE modelling. The presented research is focused on the influence of material model with anisotropic stiffness on the accuracy of deformation predictions as compared with the field measurements. A new hyperelastic-plastic model is applied to simulate anisotropic mechanical behaviour of stiff soils. It is capable...
-
Effect of carbazole and pyrrolidine functionalization of phenanthroline ligand on ground- and excited-state properties of rhenium(I) complexes. Interplay between 3MLCT and 3IL/3ILCT
PublikacjaNew rhenium(I) tricarbonyl complexes based on the phenanthroline ligand were designed and synthesized to investigate the role of carbazole (cbz) and pyrrolidine (pyrr) substituents in determining thermal, electrochemical and optoelectronic properties. Both pyrr and cbz are electron-releasing substituents, but they differ in the steric hindrance and electron delocalization ability. The impact of pyrr and cbz on ground- and excited-state...
-
Amperometric sensing of chemical oxygen demand at glassy carbon and silicon electrodes modified with boron-doped diamond
Publikacja.A boron-doped diamond (BDD) sensor is proposed for effective detection of chemical oxygen demand (COD) by means of amperometric technique. Boron-doped diamond thin films, acting as active sensors, were deposited on both silicon wafer and glassy carbon (GC) substrates by microwave plasma assisted chemical vapour deposition. SEM micrographs showed that BDD–Si displays triangle-faceted crystallites ca. 0.5–3 μm in size, while BDD–GC...
-
Titania nanotubes modified by a pyrolyzed metal-organic framework with zero valent iron centers as a photoanode with enhanced photoelectrochemical, photocatalytical activity and high capacitance
PublikacjaThe paper discusses the synthesis, photoelectrochemical and electrochemical behaviour of titania nanotube arrays modified by a pyrolyzed metal-organic framework (MOF). A poly(3,4–ethylenedioxyphene) (PEDOT) matrix with an embedded inorganic network of iron hexacyanoferrate (BP) covering TiO2 nanotubes (TNT) is used as a MOF for the further sintering procedure, resulting in a novel, thin film of carbonaceous wrap supported Fe catalytic...
-
Experimental and numerical study on deformed steel columns subjected to impact load during earthquakes
PublikacjaThe soft-storey failure is one of the most typical types of damage observed in buildings during earthquakes. The failure of an upper soft storey of a structure results in large impact load acting on the lower floors and if the resistance of the structural members of the lower storeys is not sufficient it may further lead to progressive collapse of the whole building. The aim of the present paper is to investigate the dynamic behaviour...
-
Bounds on the Cover Time of Parallel Rotor Walks
PublikacjaThe rotor-router mechanism was introduced as a deterministic alternative to the random walk in undirected graphs. In this model, a set of k identical walkers is deployed in parallel, starting from a chosen subset of nodes, and moving around the graph in synchronous steps. During the process, each node maintains a cyclic ordering of its outgoing arcs, and successively propagates walkers which visit it along its outgoing arcs in...
-
Medium-sized cyclic bis(anisylphosphonothioyl)- disulfanes and their corresponding cyclic sulfane-structures and most characteristic reactions
PublikacjaCyclic 8-, 9-, 10-, and 12-membered bis(anisylphosphonothioyl)disulfanes were synthesized. Next, structurally related 7 to 9-membered cis and trans sulfanes were isolated as a result of sulfur atom extrusion from the parent cyclic disulfanes. The results of the desulfurization of the disulfanes were compared to the results obtained for desulfurization of the respective bis(anisylphosphodithioates). Cyclic disulfanes predominantly...
-
Distributed representation of information on cyclic events
PublikacjaA representation of information on cyclic events has been proposed which is advantageous for computing environments where a distributed set of Receivers reacts to cyclic events generated by distributed sources. In such scenario no immanent central information repository exist on event timing or volume. Receivers are able to learn the event cycles without communicating with each other, merely on the basis of the fact that an event...