Wyszukiwarka
Wyniki wyszukiwania dla: ELECTRICAL METHODS
-
The unstable thermoelectric effect in non-stoichiometric Cu2Se during the non-equilibrium phase transition
PublikacjaThe superionic α ↔ β phase transition in Cu1.96Se thermoelectric material is investigated by means of thermal analysis (DSC) and measurements of Seebeck coefficient and electrical conductivity. Results of the DSC measurements with 1–10 K/min heating and cooling rates show that the material is close to the equilibrium phase composition during the transformation. However, the kinetic limitation of the process exists, which is indicated...
-
Application of additional factors supporting the microextraction process
PublikacjaDue to the fact that green analytical chemistry is of high importance, the past two decades have witnessed a rapid growth in the sample preparation area with special emphasis on simplification, miniaturization and automation of extraction procedures. In addition, to accelerate the extraction processes and to improve the separation of analytes, several enhanced parameters are applied. These factors include, ultrasounds, microwaves,...
-
Conversion of Biomass and Municipal Wastes into Syngas and Hydrogen using Highly Preheated Agent (HTAG)
PublikacjaGasification is considered to be one of the most promising energy recovery technologies for the widespread utilization of biomass and wastes. During this process raw feedstock is converted into a combustible gas, which can then be burnt to produce thermal energy, or to run engines for mechanical or electrical power. The studies of biomass gasification demonstrate it as a friendly alternative to fossil fuels as one of renewable...
-
Objective relaxation algorithm for reliable simulation-driven size reduction of antenna structure
PublikacjaThis letter investigates reliable size reduction of antennas through electromagnetic-driven optimization. It is demonstrated that conventional formulation of the design task by direct footprint miniaturization with imposing constraints on electrical performance parameters may not lead to optimum results. The reason is that—in a typical antenna structure—only a few geometry parameters explicitly determine the antenna footprint,...
-
Modeling the impact of rotor movement on non-linearity of motor currents waveforms in high-speed PMSM drives
PublikacjaMotor current measurement techniques as well as predictive control algorithms for electric drives rely on an assumption of linear motor currents changes resulting from constant inverter output voltages. Recent research has reported that this assumption does not hold in motors with short electrical time constant, and in drives whose rotor position advances substantially during a control period. This paper proposes a simulation model...
-
Neoclassical Navier–Stokes Equations Considering the Gyftopoulos–Beretta Exposition of Thermodynamics
PublikacjaThe seminal Navier-Stokes equations were stated even before the creation of the foundations of thermodynamics and its first and second laws. There is a widespread opinion in the literature on thermodynamic cycles that the Navier-Stokes equations cannot be taken as a thermodynamically correct model of a local "working fluid", which would be able to describe the conversion of "heating" into "working" (Carnot's type cycles) and vice...
-
Determining and verifying the safety integrity level of the controland protection systems under uncertainty
PublikacjaThe probabilistic models of the electrical, electronic and programmable electronic (E/E/PE)systems, which are proposed in the IEC 61508 and IEC 61511 standards, do not cover the uncertainty aspectsof results obtained from these models. The proposed method takes into consideration the sensitivity analysisof probabilistic models of E/E/PE systems as well as the uncertainty of probabilistic results. It uses differentialfactors, which...
-
Rattling-enhanced superconductivity in MV2Al20 (M = Sc, Lu, Y) intermetallic cage compounds
PublikacjaPolycrystalline samples of four intermetallic compounds: MV2Al20 (M=Sc, Y, La, and Lu) were synthesized using an arc-melting technique. The crystal structures were analyzed by means of powder x-ray diffraction and Rietveld analysis, and the physical properties were studied by means of heat capacity, electrical resistivity, and magnetic susceptibility measurements down to 0.4 K. For ScV2Al20, LuV2Al20, and YV2Al20, superconductivity...
-
ASSESSMENT OF UNDERPOWER ED PROPULSION MACHINERY IN ELECTRICALLY DRIVEN SMALL INLAND WATERWAY PASSENGER SHIPS FROM CLASSIFICATION SOCIETY POINT OF View
PublikacjaPaper presents short operat ional a nd engineering analysis of underpowered propulsion in small electrically propelled small inland passenger ships. There is evidence that in certain weather conditions the phenomena of added aerodynamic resistance of small water crafts may have serious influence on their speed and manoeuvrability. Existing regulations like class societies rules for ship classification and construction or EU Directive 2006/87/EC do...
-
Assessment of under power ed propulsion machinery in electrically driven small inland waterway passenger ships from classification society point of view
PublikacjaPaper presents short operat ional a nd engineering analysis of underpowered propulsion in small electrically propelled small inland passenger ships. There is evidence that in certain weather conditions the phenomena of added aerodynamic resistance of small water crafts may have seriou s influence on their speed and manoeuvrability. Existing regulations like class societies rules for ship classification and construction or EU Directive 2006/87/EC do...
-
PV installations and the safety of residential buildings
PublikacjaThe dynamic development of the photovoltaic industry entails threats that have a direct impact on the safety of residential buildings. Appropriate design of a PV installation can be a challenge due to the multifaceted nature of this issue. The designer should take into account issues related to the selection of electrical parameters of the installation, adapting lightning and surge protection in accordance...
-
CuMn1.7Fe0.3O4 – RE2O3 (RE=Y, Gd) bilayers as protective interconnect coatings for Solid Oxide Cells
PublikacjaEfficient replacement of materials based on critical elements such as cobalt is one of the greatest challenges facing the field of solid oxide cells. New generation materials, free of cobalt show potential to replace conventional materials. However, these materials are characterized by poor ability to block chromium diffusion. This article described the study of CuMn1.7Fe0.3O4 (CMFO) spinel combined with single metal oxide (Y2O3...
-
Performance of microbial fuel cells operated under anoxic conditions
PublikacjaNowadays, microbial fuel cells (MFC) stand up as a promising renewable energy source. Due to the ability of the MFC to oxidize a wide spectrum of substrates, wastewater seems to be one of the most interesting fuels. Unfortunately, wastewater could contain electron acceptors such as nitrate, which could interfere with the electrical performance of the MFC. In this work, the influence of oxidised nitrogen forms on the electricity...
-
A model development and experimental verification for a vapour microturbine with a permanent magnet synchronous generator
PublikacjaVapour microturbines with permanent magnet synchronous generators are implemented in micropower plants for dispersed power generation systems. The dynamic model of such a microturbine set was developed and presented. The developed relations result from the generic equations. Experimental data for two different working medium were used for model verification. A microturbine set model was tested during the changes in the parameters...
-
Tin Oxide Encapsulated into Pyrolyzed Chitosan as a Negative Electrode for Lithium Ion Batteries
PublikacjaTin oxide is one of the most promising electrode materials as a negative electrode for lithium-ion batteries due to its higher theoretical specific capacity than graphite. However, it suffers lack of stability due to volume changes and low electrical conductivity while cycling. To overcome these issues, a new composite consisting of SnO2 and carbonaceous matrix was fabricated. Naturally abundant and renewable chitosan was chosen...
-
Fault Loop Impedance Measurement in Circuits Fed by UPS and Principle of Safety Protection
PublikacjaThis paper indicates a significant problem of uncertainty of fault loop impedance (FLI) measurement in circuits powered from uninterruptible power supply (UPS) (double-conversion AC-DC-AC). The correctly determined value of this impedance, related to the short-circuit current disconnection time and to the reference value, is one of the most important elements that determines the approval of an electrical installation and its receivers...
-
Ultrafast degradation of brilliant cresyl blue under hydrodynamic cavitation based advanced oxidation processes (AOPs)
PublikacjaThe study highlights effectiveness of hydrodynamic cavitation (HC) in the degradation of effluents polluted by Brilliant Cresyl Blue (BCB) dye. Optimal process parameters were cavitation number 0.27, inlet pressure 1.70 bar, temperature 20 °C and pH 7. The efficiency of HC was investigated in combination with other advanced oxidation processes, including the addition of external oxidants (hydrogen peroxide, ozone, and sodium persulfate)...
-
Electrocatalytic oxidation of methanol, ethylene glycol and glycerine in alkaline media on TiO2 nanotubes decorated with AuCu nanoparticles for an application in fuel cells
PublikacjaIn this work, we present the catalytic and photocatalytic activity of AuCu nanostructures obtained on TiO2 nanotubes toward methanol, ethylene glycol and glycerine oxidation. The electrode material is prepared by anodization of Ti foil, thin AuCu layer sputtering and rapid thermal treatment under argon atmosphere. Scanning electron microscopy images confirmed the presence of ordered tubular architecture of TiO2 as well as nanoparticles...
-
Superconductivity in the intermetallic compound Zr5Al4
PublikacjaPolycrystalline Zr5Al4 was synthesized using the arc-melting method. Powder X-ray diffraction confirms the previously reported crystal structure of the Ti5Ga4-type P63/mcm with lattice parameters: a = 8.4312(6) A , and c = 5.7752(8) A . Electrical resistivity and low-temperature magnetic susceptibility measurements indicate that Zr5Al4 exhibits superconducting behavior below 2 K. The normalized heat capacity jump at Tc= 1.82 K...
-
Impedance Measurement and Selection of Electrochemical Equivalent Circuit of a Working PEM Fuel Cell Cathode
PublikacjaThe dynamic impedance analysis of direct methanolfuel cell (DMFC) cathode supplied with pure oxygen is pre-sented. Presented results were obtained during dynamic chang-es of the current density in working fuel cell. Investigation ofthe occurring processes at cathode was carried with dynamicelectrochemical impedance spectroscopy (DEIS). A discussionwas conducted based on the determined correlation parameterχ2. It was shown that...
-
Magnetoelectric effect in (BiFeO3)x–(BaTiO3)1-x solid solutions
PublikacjaThe aim of the present work was to study magnetoelectric effect (ME) in (BiFeO3)x–(BaTiO3)1x solid solutions in terms of technological conditions applied in the samples fabrication process. The rapidly growing interest in these materials is caused by their multiferroic behaviour, i.e. coexistence of both electric and magnetic ordering. It creates possibility for many innovative applications, e.g. in steering the magnetic memory...
-
Enhancing electrochemical properties of an ITO-coated lossy-mode resonance optical fiber sensor by electrodeposition of PEDOT:PSS
PublikacjaA sensor working in multiple domains may offer enhanced information about the properties of an investigated analyte, including those containing biological species. It has already been shown that a dual-domain sensing capability, i.e., in optical and electrochemical domains, can be offered by lossy-mode resonance (LMR) sensors based on indium-tin-oxide (ITO) thin film. The spectral response of the LMR sensors depends on the refractive...
-
Analysis of the harmonic structure of the vowel /a/ taking into account the age and gender of the speaker
PublikacjaSound waves are disturbances propagating through an elastic medium that, upon reaching the ear, elicit auditory sensations. Sounds generated by the surroundings can be captured by a transducer (microphone), which transforms them into an electrical signal. The signal from the microphone is then transmitted to a computer, where software allows for the extraction and analysis of individual tones. This process enables the description...
-
Superconductivity in PrBa 2Cu 3O 7− δ single crystals after high-temperature thermal treatment
PublikacjaThe influence of post-growth treatment, consisting of high-temperature reduction, quench and oxidation, on the structural, electrical and magnetic properties of PrBa2Cu3O7−δ single crystals, obtained in Al2O3 and ZrO2 crucibles by the self-flux method, was examined. We report on the observation of inhomogeneous superconductivity in several Al-doped crystals from the ac magnetic susceptibility and resistivity measurements. Superconducting...
-
FURTHER REMARKS ON THE SURFACE VIS IMPRESSA CAUSED BY A FLUID-SOLID CONTACT
PublikacjaIt is well-known that, nano-mechanics should take into account not only physical phenomena occuring within the bulk but, first of all, the physical phenomena appropriate for a surface of two materials contact. The huge volume density of internal surfaces as well countours lines located within the nanomaterial results in our interest in, apart from classical form of mass, momentum and entropy transport, those modes of transportation...
-
CFFT columns in road through railroad crossings
PublikacjaThere were 12801 road through railroad one-level crossings in Poland in 2018. 215 accidents happened at them in 2018. In order to increase safety in rail and road traffic two-level crossings should be used. They are definitely safer and make the traffic more smooth. In the design and construction of two-level intersections of railway and road or path columns of circular cross-section are often used. They can be successfully replaced...
-
Mechanism of hopping conduction in Be–Fe–Al–Te–O semiconducting glasses and glass–ceramics
PublikacjaElectrical properties of beryllium-alumino-tellurite glasses and glass–ceramics doped with iron ions were studied using impedance spectroscopy. The conductivity was measured over a wide frequency range from 10 mHz to 1 MHz and the temperature range from 213 to 473 K. The D.C. conductivity values showed a correlation with the Fe-ion concentration and ratio of iron ions on different valence states in the samples. On the basis of...
-
High-conducting Bi4V2-xFexO11-δ ceramics containing Fe2O3 nanocrystals: Structure and properties
PublikacjaThe topography, structure, thermal, magnetic, and electrical properties of Bi4V2-xFexO11-δ ceramics substituted with x = 0.5 and 0.7 Fe were studied. The microscope analysis showed the presence of iron-rich nanocrystals formed on the Bi-Fe-V-O grains. The X-ray diffraction studies confirmed that grains are built mostly of tetragonal Bi4V1.5Fe0.5O10.5 phase. Thermal properties analysis showed an order-disorder type γ ↔ γʹ phase...
-
Implementation of Extended Kalman Filter with Optimized Execution Time for Sensorless Control of a PMSM Using ARM Cortex-M3 Microcontroller
PublikacjaThis paper addresses the implementation and optimization of an Extended Kalman Filter (EKF) for the Permanent Magnet Synchronous Motor (PMSM) sensorless control using an ARM Cortex-M3 microcontroller. A various optimization levels based on arithmetic calculation reduction was implemented in ARM Cortex-M3 microcontroller. The execution time of EKF estimator was reduced from 260.4 μs to 37.7 μs without loss of accuracy. To further...
-
MgPd2Sb : A Mg-based Heusler-type superconductor
PublikacjaWe report the synthesis and physical properties of a full Heusler compound, MgPd2Sb, which we found toshow superconductivity belowTc=2.2K. MgPd2Sb was obtained by a two-step solid-state reaction methodand its purity and cubic crystal structure [Fm-3m,a=6.4523(1) Å] were confirmed by powder x-ray diffrac-tion. Normal and superconducting states were studied by electrical resistivity, magnetic susceptibility, andheat...
-
Application of Rapid Prototyping technology in the manufacturing of turbine blade with small diameter holes
PublikacjaThe article presents the possibilities of using Rapid Prototyping (RP) technology in the manufacturing of turbine blades with small diameter holes. The object under investigation was gas turbine blade with small diameter cooling holes and holes for generating longitudinal vortices. A turbine blade model was produced by means of Direct Metal Laser Sintering (DMLS) technology and subsequently validated in terms of detection and accuracy...
-
Direct brain stimulation modulates encoding states and memory performance in humans
PublikacjaPeople often forget information because they fail to effectively encode it. Here, we test the hypothesis that targeted electrical stimulation can modulate neural encoding states and subsequent memory outcomes. Using recordings from neurosurgical epilepsy patients with intracranially implanted electrodes, we trained multivariate classifiers to discriminate spectral activity during learning that predicted remembering from forgetting,...
-
Selected Aspects of Biofuels Market and the Electromobility Development in Poland: Current Trends and Forecasting Changes
PublikacjaThis work presents basic information associated with markets of selected alternative fuels used in transport, such as methyl esters, conventional bioethanol and lignocellulosic bioethanol, and the market of electrical vehicles. Legal conditions, which stimulate development and regulate the mode of functioning of the liquid biofuel market until 2020 are discussed, based on provisions of EU directives. Data on biofuel production...
-
Model Correction and Optimization Framework for Expedited EM-Driven Surrogate-Assisted Design of Compact Antennas
PublikacjaDesign of compact antennas is a numerically challenging process that heavily relies on electromagnetic (EM) simulations and numerical optimization algorithms. For reliability of simulation results, EM models of small radiators often include connectors which—despite being components with fixed dimensions—significantly contribute to evaluation cost. In this letter, a response correction method for antenna models without connector,...
-
Thermal and hydraulic phenomena in boundary layer of minijets impingement on curved surfaces
PublikacjaPresented work considers flow and thermal phenomena occurring during the single minijet impingement on curved surfaces, heated with a constant heat flux, as well as the array of minijets. Numerical analyses, based on the mass, momentum and energy conservation laws, were conducted, regarding single phase and two-phase simulations. Focus was placed on the proper model construction, in which turbulence and boundary layer modeling...
-
Nonlinear secondary arc model use for evaluation of single pole auto-reclosing effectiveness
PublikacjaPurpose – The purpose of this paper is to discuss two evaluation methods of single pole autoreclosing process effectiveness in HV transmission lines. Secondary arc current and recovery voltage results obtained by load flow calculation are compared to the results obtained by the time domain simulations. Moreover, a nonlinear secondary arc implementation is presented. Design/methodology/approach – A computer simulation studies were...
-
The effect of interview location on the perception of Ecosystem Services provided by trees. A Polish case study.
Dane BadawczeSeveral survey research methods are available to study attitudes towards the environment, including: CAWI (computer-assisted Internet interview), CATI (computer-assisted telephone interview), CAPI (computer-assisted personal interview), and PAPI (paper-pencil interview). An increasingly popular CAWI approach is the geo-questionnaire – an internet survey...
-
Permanent traffic count stations - expressway S6 Poland 2016
Dane BadawczeThe data includes traffic data from permanent traffic count stations located on the expressway S6 in the Tri-City Agglomeration area in Poland. The data covers the 12 months of 2016.
-
Video traffic data - Interchange Bielany (A4-5) - weaving, Poland
Dane BadawczeThe data includes video traffic data registered with 12 video cameras at weaving area (weaving section type A) of the Bielany interchange within A4 motorway in Poland (interchange of motorway A4 and nacional road 5), located in the Silesian Agglomeration.The data covers the one day: 07.06.2017 (motorway A4)
-
Video traffic data - Interchanges Wolnosci (86 - 94)
Dane BadawczeThe data includes video traffic data registered with 3 video cameras at entry or exit lanes of the Wolnosci interchange within 86 national road in Poland (interchange of national roads 86 and 94 ), located in the Silesian Agglomeration). The data covers the one days: 22.05.201 (national road 86).
-
Video traffic data - Interchange Slowackiego (S8-Slowackiego), Poland
Dane BadawczeThe data includes video traffic data registered with 4 video cameras at entry or exit lanes of the Slowackiego interchange within S8 expressway in Poland (interchange of expressway S8 and Slowackiego street), located in the Warsaw Agglomeration. The data covers the one day: 10-11.05.2017 (expressway S8).
-
Video traffic data - Interchange Tychy (1-44), Poland
Dane BadawczeThe data includes video traffic data registered with 8 video cameras at weaving area (weaving section type A) of the Tychy interchange within national road 1 in Poland (interchange of national roads 1 and 44), located in the Silesian Agglomeration. The data covers the two days:13-14.09.2017.
-
Video traffic data - Interchange Broniewskiego (S8-Broniewskiego), Poland
Dane BadawczeThe data includes video traffic data registered with 4 video cameras at entry or exit lanes of the Broniewskiego interchange within S8 expressway in Poland (interchange of expressway S8 and Broniewskiego street), located in the Warsaw Agglomeration. The data covers the two days: 10-11.05.2017 (expressway S8).
-
Glutathione conjugation of the antitumor-active 1-nitroacridine derivatives compounds C-857 and C-1748 – the major role of glutathione S-transferase M1-1
Dane BadawczeObjectives: C-857 and C-1748 are antitumor-active agents, monomers of unsymmetrical bisacridine derivatives. The aim of this study was to analyze their glutathione (GSH) conjugation in vitro in the presence of glutathione S-transferase (GST) M1-1.
-
Cathodic activation of synthesized highly defective monoclinic hydroxyl‐functionalized ZrO2 nanoparticles for efficient electrochemical production of hydrogen in alkaline media
PublikacjaThe high electrochemical stability of Zirconia (ZrO2) at high potentials strongly suggested it as an alternative to carbon supports, which experience reduced efficiency due to some corrosion problems particularly during prolonged electrocatalysis activity. However, the use of ZrO2 was limited by its low electrical conductivity and surface area. In this work, we developed a methodology for synthesizing monoclinic ZrO2 NPs with increased...
-
Graphene-based Silicone rubber Nanocomposites: Preparation, Characterization, and Properties
PublikacjaThis study aims to understand better the mechanical, thermal, and tribological behavior of silicone rubber nanocomposites. Graphite, exfoliated graphite, reduced graphene oxide, ionic liquid modified graphene oxide, silane-modified graphene oxide, fumed silica, and other fillers were used in this study. Adding graphene-based fillers to the silicone rubber matrix substantially improves the nanocomposite's mechanical, thermal, and...
-
TIME- AND FREQUENCY-DOMAIN QUASI-2D SMALL-SIGNAL MOSFET MODELS
PublikacjaA novel approach to small-signal MOSFET modeling is presented in this book. As a result, time- and frequency-domain physics-based quasi-2D NQS four-terminal small-signal MOSFET models are proposed. The time-domain model provides the background to a novel DIBL-included quasi‑2D NQS four-terminal frequency-domain small-signal MOSFET model. Parameters and electrical quantities of the frequency-domain model are described by explicit...
-
Multi-objective optimization of microwave couplers using corrected domain patching
PublikacjaPractical design of microwave components and circuits is a compromise between various, often conflicting objectives. In case of compact structures, the trade-offs are typically concerned with the circuit size and its electrical performance. Comprehensive information about the best possible trade-offs can be obtained by means of multi-objective optimization. In this paper, we propose a computationally efficient technique for identifying...
-
Solid State Conductivity of Optimized Polypyrrole Coatings on Iron Obtained from Aqueous Sodium Salicylate Solution Determined by Impedance Spectroscopy
PublikacjaIn this work the optimization procedure for corrosion resistance, surface analysis and electrical properties of PPy-Fe electrodes have been examined. Polypyrrole (PPy) film was electrochemically synthesized in a one step process from an aqueous solution of sodium salicylate and pyrrole with certain concentrations, different parameters and type of polymerization...
-
Half-Order Modeling of Saturated Synchronous Machine
PublikacjaNoninteger order systems are used to model diffusion in conductive parts of electrical machines as they lead to more compact and knowledge models but also to improve their precision. In this paper a linear half-order impedance model of a ferromagnetic sheet deduced from the diffusion of magnetic field is briefly introduced. Then, from physical considerations and finite elements simulation, the nonlinear half-order impedance model...