Wyszukiwarka
Filtry
wszystkich: 1919
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: EXPERIMENTAL RESULTS
-
ENERGY ANALYSIS OF PROPULSION SHAFT FATIGUE PROCESS IN ROTATING MECHANICAL SYSTEM PART I TESTING SIGNIFICANCE OF INFLUENCE OF SHAFT MATERIAL FATIGUE EXCITATION PARAMETERS
PublikacjaThe article discusses the problem of mathematical modelling of energy conversion processes in a rotating mechanical system for the purpose of identifying fatigue states of propulsion shafts in this system. A simplified physical model of the analysed system, constructed in an appropriate scale, has made the basis for the experimental research. The research programme took into consideration mechanical fatigue excitation of the model...
-
Optimization of the Aeration Strategies in a Deammonification Sequencing Batch Reactor for Efficient Nitrogen Removal and Mitigation of N2O Production
PublikacjaIn deammonification systems, nitrite-oxidizing bacteria (NOB) suppression and nitrous oxide (N2O) mitigation are two important operational objectives. To carry out this multivariable analysis of response, a comprehensive model for the N cycle was developed and evaluated against experimental data from a laboratory-scale deammonification granular sludge sequencing batch reactor. Different aeration strategies were tested, and the manipulated...
-
Study of the Performance of DSSS UAC System Depending on the System Bandwidth and the Spreading Sequence
PublikacjaA signal transmitted in an Underwater Acoustic Communication (UAC) system operating in a shallow-water channel suffers from strong time dispersion due to multipath propagation. This causes the Inter-Symbol Interference (ISI) observed in the received signal, which significantly limits the communication system’s reliability and transmission rate. In such propagation conditions, the Direct-Sequence Spread Spectrum (DSSS) method is...
-
Person Tracking in Ultra-Wide Band Hybrid Localization System Using Reduced Number of Reference Nodes
PublikacjaIn this article a novel method of positional data integration in an indoor hybrid localization system combining inertial navigation with radio distance measurements is presented. A point of interest is the situation when the positional data and the radio distance measurements are obtained from less than thee reference nodes and it is impossible to unambiguously localize the moving person due to undetermined set of positional equations....
-
Nonlinear material identification of heterogeneous isogeometric Kirchhoff–Love shells
PublikacjaThis work presents a Finite Element Model Updating inverse methodology for reconstructing heterogeneous materialdistributions based on an efficient isogeometric shell formulation. It uses nonlinear hyperelastic material models suitable fordescribing incompressible material behavior as well as initially curved shells. The material distribution is discretized by bilinearelements such that the nodal values...
-
Wpływ parametrów strugi paliwa wtryskiwanego do cylindra silnika okrętowego na początkową fazę rozpylania
PublikacjaPrzedmiotem rozprawy jest analiza procesu wtrysku oleju napędowego do cylindra silnika okrętowego z zapłonem samoczynnym i bezpośrednim wtryskiem paliwa. Analiza tego zagadnienia została przeprowadzona w aspekcie wpływu makro parametrów strugi na początkową fazę rozpylania oleju napędowego. Celem niniejszej pracy jest określenie wpływu współczynnika L/D (długość otworu/średnica) otworu wylotowego wtryskiwacza na zmianę charakterystyki...
-
Study on Polymer Elements for Mitigation of Earthquake-Induced Pounding Between Buildings in Complex Arrangements
PublikacjaPounding between neighboring structures during seismic events has been revealed as one of the most commonly observed reasons for severe damage or even total collapse of the adjacent buildings. Therefore, pounding effects have recently become an issue of great interest of many numerical and experimental investigations in many earthquake-prone regions of the world. It has also been observed that the differences in dynamic characteristics...
-
Experiment-Based Study of Heat Dissipation from the Power Cable in a Casing Pipe
PublikacjaThe paper deals with the important challenges in terms of electricity transmission by means of underground cable lines. The power cable’s performance is characterized by an ampacity that represents its maximum electric current-carrying capacity. The ampacity of power cables depends on their ability to diffuse the heat generated by the current flow into the environment. In the performed research, the analysis of the efficiency of...
-
Experimental investigation of Steel–Concrete–Polymer composite barrier for the ship internal tank construction
PublikacjaTransportation of dangerous cargo by ships demands ensuring an appropriate protection level in case of an accident. Two of the most dangerous accident types resulting in an oil spill are grounding and ship to ship collision. The article presents results of research on a new composite construction for a ship hull that increases structural safety during collision. The concept of semi-elastic Steel–Concrete–Polymer structure is presented....
-
Analiza porównawcza procesów tłumienia i wygładzania fali ciśnienia w trakcie nieustalonego przepływu w rurociągach wykonanych z różnych materiałów.
PublikacjaUderzenie hydrauliczne jest uważane za jeden z najważniejszych problemów nieustalonego przepływu w przewodach, dlatego nadal stanowi obiekt badań wielu naukowców. To zagadnienie może być badane na dwóch poziomach: praktycznym i teoretycznym. W artykule zaprezentowane zostały wyniki badań doświadczalnych przeprowadzonych na stanowisku pomiarowym nieustalonego przepływu, funkcjonującym w Laboratorium Hydraulicznym Wydziału Inżynierii...
-
Earthquake-induced pounding between asymmetric steel buildings
PublikacjaEarthquake-induced pounding between buildings has been the subject of numerous numerical and experimental studies in the resent years. The phe-nomenon may cause severe damage to structural elements as well as may also lead to the total collapse of colliding structures. A major reason leading to pounding between adjacent, insufficiently separated buildings results from the differences in their dynamic properties. The aim of this...
-
Torque capacity of multidisc wet clutch with reference to friction occurrence on its spline connections
PublikacjaIn this article developed mathematical model that includes friction occurrence on spline connections is presented. The work also contains results of experimental research on torque capacity of multidisc wet clutch. These results are expressed as a function of contact pressure for different number of friction surfaces. Due to increased interest in research concerning multidisc wet clutches it is essential to determine impact of...
-
Monte Carlo simulations of the fracture resistance degradation of asphalt concrete subjected to environmental factors
PublikacjaThe paper presents the results of laboratory tests of SCB (semi-circular beam) samples of asphalt concrete, subjected to the destructive effect of water and frost as well as the aging processes. The determined values of material parameters show significant dispersions, which makes the design of mixtures difficult. Statistical analysis of the test results supplemented by computer simulations made with the use of the proprietary...
-
Thermo-Mechanical Simulation of Underwater Friction Stir Welding of Low Carbon Steel
PublikacjaThis article investigates the flow of materials and weld formation during underwater friction stir welding (UFSW) of low carbon steel. A thermo-mechanical model is used to understand the relation between frictional heat phenomena during the welding and weld properties. To better understand the effects of the water environment, the simulation and experimental results were compared with the sample prepared by the traditional friction...
-
Experimental study on the seepage flow through the ice jam
PublikacjaIn light of the observed climate change, there is a need for better understanding of river ice processes for managing water resources in the cold regions. Ice jams produce significant resistance which may cause rise of water level and flooding. The jam resistance is only referred to the roughness of its underside, and this approach lead to exceptional roughness coefficients which has no physical explanation. Number of evidences...
-
<title>Cavity simulator and controller for VUV free electron laser SIMCON 2.1, part III: I/O ports and measurement results</title>
Publikacja -
Analysis of the risk factors for perioperative morbidity after laparoscopic revisional bariatric procedures: results from the multicenter Polish Revision Obesity Surgery Study
Publikacja -
Complicated appendicitis: risk factors and outcomes of laparoscopic appendectomy – results from Pol-LA (Polish Laparoscopic Appendectomy) multicenter large cohort study.
Publikacja -
Long-term safety and efficacy of benralizumab in patients with severe, uncontrolled asthma: 1-year results from the BORA phase 3 extension trial
Publikacja -
Allelic length of a CA dinucleotide repeat in theegfr gene correlates with the frequency of amplifications of this sequence—first results of an inter-ethnic breast cancer study
Publikacja -
A European Research Agenda for Somatic Symptom Disorders, Bodily Distress Disorders, and Functional Disorders: Results of an Estimate-Talk-Estimate Delphi Expert Study
Publikacja -
Clinical Course and Severity of COVID-19 in 940 Infants with and without Comorbidities Hospitalized in 2020 and 2021: The Results of the National Multicenter Database SARSTer-PED
Publikacja -
Pediatric Inflammatory Multisystem Syndrome (PIMS) Did Occur in Poland during Months with Low COVID-19 Prevalence, Preliminary Results of a Nationwide Register
Publikacja -
The conversion of multinuclear μ-oxo titanium(IV) species in the reaction of Ti(OiBu)4 with branched organic acids; results of structural and spectroscopic studies
PublikacjaW reakcji tetraizobutoksylanu tytanu z rozgałęzionymi kwasami karboksylowymi otrzymano szereg wielordzeniowych związków kompleksowych tytanu(IV). Otrzymane produkty scharakteryzowano wykorzystując techniki spektroskopowe: FTIR, 1H i 13C NMR oraz rentgenowską analizę strukturalną. Zaproponowano ścieżki reakcji prowadzące do konwersji poszczególnych związków w coraz stabilniejsze formy.
-
Prediction of metal deformation due to line heating; an alternative method of mechanical bending, based on artificial neural network approach
PublikacjaLine heating is one of the alternative methods of forming metals and this kind of forming uses the heating torch as a source of heat input. During the process, many parameters are considered like the size of the substrate, thickness, cooling method, source power intensity, the travel speed of the power source, the sequence of heating, and so on. It is important to analyze the factors affecting the...
-
Increased Certification of Semi-device Independent Random Numbers using Many Inputs and More Postprocessing
PublikacjaQuantum communication with systems of dimension larger than two provides advantages in information processing tasks. Examples include higher rates of key distribution and random number generation. The main disadvantage of using such multi-dimensional quantum systems is the increased complexity of the experimental setup. Here, we analyze a not-so-obvious problem: the relation between randomness certification and computational requirements...
-
Recent advances of selected passive heat transfer intensification methods for phase change material-based latent heat energy storage units: A review
PublikacjaThe following article overviews recent studies regarding heat transfer enhancement methods, explicitly focusing on fins and coils utilization, in phase change material-based latent heat thermal energy storage systems. It discusses the influence of various geometrical and material parameters on the melting and solidification processes, as well as the orientation of the heat transfer surface within the storage tank. Additionally,...
-
Technical State Assessment of Charge Exchange System of Self-Ignition Engine, Based On the Exhaust Gas Composition Testing
PublikacjaThis paper presents possible use of results of exhaust gas composition testing of self - ignition engine for technical state assessment of its charge exchange system under assumption that there is strong correlation between considered structure parameters and output signals in the form of concentration of toxic compounds (ZT) as well as unambiguous character of their changes. Concentration of the analyzed ZT may be hence considered...
-
Experimental Verification of the CFD Model of the Squeeze Film Lifting Effect
PublikacjaAbstract: The presented study shows the results of the research into the squeeze film levitation phenomena. The system introduced in the investigation is composed of a vibrating surface, air squeeze film, and the surface of the body freely suspended over the film. The use of the CFD (Computational Fluid Dynamics) model used in the system allows us to determine the steady state, periodic behavior of the air film (described by Navier–Stokes,...
-
Mathematical Modelling of a Seismic Isolation System to Protect Structures During Damaging Earthquakes
PublikacjaThe present study aims to determine the effectiveness of a nonlinear mathematical model in simulating complex mechanical behaviour of a seismic isolation system to protect structures during strong and damaging earthquakes. In order to construct the Polymeric Bearings considered in this research, a specially prepared flexible polyurethane elastomer with increased damping properties has been used. The usefulness of the proposed mathematical...
-
Dynamic soil improvement by hybrid technologies
PublikacjaHybrid method of subsoil improvement for road embankment foundation is described. This method is composed of two wellknown methods: dynamic replacement (DR) and microblasting (DDC) one (Deep Dynamic Compaction). The method was used for both the strengthening of the fully saturated organic subsoil as well as for acceleration of the consolidation of the organic layers. The practice ensures the expected results. A proper example on...
-
Modelling of the Heat Flux Density Distribution for Laser Beam Welding
PublikacjaGreat interest of the laser beam welding in industry is a new theoretical task, making planning the welding procedure specification and the quality control of welded joints easier. Estimating and calculating the dimensions of a weld pool and temperature distribution near weld mainly concern heat source modelling. In the presented work calculations of welding pool shape and thermal field for cylindrical-powered-normally model of...
-
Modeling and Strength Calculations of Parts Made Using 3D Printing Technology and Mounted in a Custom-Made Lower Limb Exoskeleton
PublikacjaThis study is focused on the application of 3D-printed elements and conventional elements to create a prototype of a custom-made exoskeleton for lower limb rehabilitation. The 3D-printed elements were produced by using Fused Deposition Modeling technology and acrylonitrile butadiene styrene (ABS) material. The scope of this work involved the design and construction of an exoskeleton, experimental testing of the ABS material and...
-
Visualization of a lifeboat motion during lowering along ship’s side
PublikacjaThis paper presents description of a computer program for motion visualization of a lifeboat lowered along ship’s side. The program is a post-processor which reads results of numerical calculations of simulated objects’ motions. The data is used to create scene composed of 3D surfaces to visualize mutual spatial positions of a lifeboat, ship’s side and water waving surface. Since the numerical data contain description of a simulation...
-
Objective relaxation algorithm for reliable simulation-driven size reduction of antenna structure
PublikacjaThis letter investigates reliable size reduction of antennas through electromagnetic-driven optimization. It is demonstrated that conventional formulation of the design task by direct footprint miniaturization with imposing constraints on electrical performance parameters may not lead to optimum results. The reason is that—in a typical antenna structure—only a few geometry parameters explicitly determine the antenna footprint,...
-
Signal filtering method of the fast-varying diesel exhaust gas temperature
PublikacjaThe paper presents the problem of the impact of external distortions originating on laboratory test stands on the results of measurements of fast-varying diesel exhaust gas temperature. It has been stressed how significant the aspect of the test stand adaptation is during an experiment to ensure the smallest possible impact. This paper, however, focuses on the methods of mathematical processing of a signal recorded during experimental...
-
FEM modelling of stress and strain distribution in weld joints of steel sandwich panels
PublikacjaThe development of laser welding technology has enabled the mass production of thin-walled structures, including steel sandwich panels. The technology of joining plating panels with stiffeners by welding allows us to create joints with a specific geometry and material properties. In comparison with other types of joints, laser welds are characterized by their specific behaviour under cyclic load and, as a consequence, a different...
-
Polymeric Bearings as a new base isolation system suitable for mitigating machine-induced vibrations
PublikacjaThe present paper summarizes the preliminary results of the experimental shaking table investigation conducted in order to verify the effectiveness of a new base isolation system consisting of Polymeric Bearings in reducing strong horizontal machine-induced vibrations. Polymeric Bearing considered in the present study is a prototype base isolation system, which was constructed with the use of a specially prepared flexible polymer...
-
Evaluating Asymmetric N-Grams as Spell-Checking Mechanism
PublikacjaTypical approaches to string comparing marks two strings as either different or equal without taking into account any similarity measures. Being able to judge similarity is however required for spelling error corrections, as we want to find the best match for a given word. In this paper we present a bi2quadro-grams method for spelling errors correction. The method proposed uses different n-grams dimension for the source (checked)...
-
The assessment of metrological properties of segmental orifice based on simulations and experiments
PublikacjaSegmental orifices are often used to measure flows of heterogeneous mixtures, especially in flow meters in the power industry, for example. The orifice (with module m= 0.25) was installed in a stainless-steel pipe with internal diameter of 50 mm, placed in a hydraulic water system. The research was performed for Reynolds numbers ranging from 9,000 to 17,000. The flow characteristics of this orifice obtained based on simulation...
-
Mathematical modeling of hydrogen production performance in thermocatalytic reactor based on the intermetallic phase of Ni3Al
PublikacjaThe main goal of the following work is to adjust mathematical modelling for mass transfer, to specific conditions resulting from presence of chemical surface reactions in the flow of the mixture consisting of helium and methanol. The thermocatalytic devices used for decomposition of organic compounds incorporate microchannels coupled at the ends and heated to 500 oC at the walls regions. The results of the experiment were compared...
-
An Improved Convolutional Neural Network for Steganalysis in the Scenario of Reuse of the Stego-Key
PublikacjaThe topic of this paper is the use of deep learning techniques, more specifically convolutional neural networks, for steganalysis of digital images. The steganalysis scenario of the repeated use of the stego-key is considered. Firstly, a study of the influence of the depth and width of the convolution layers on the effectiveness of classification was conducted. Next, a study on the influence of depth and width of fully connected...
-
Torque Transmitted by Multi-plate Wet Clutches in Relation to Number of Friction Plates and Their Dimensions
PublikacjaIn the paper results of experimental tests on multi-plate wet clutch torque capacity for various diameters and numbers of friction plates are presented. Construction of an apparatus for laboratory tests of wet clutch engagement, drag torque and maximum torque is shown. Methodology of maximum torque capacity experiment and hydraulic circuit diagram, which supplies a motor and an actuator for the experiment are described. Analytically...
-
Influence of Sn and Pb Ions Substitutions on Dielectric Properties of Barium Titanate
PublikacjaThe results of the microstructural and dielectric measurements of (Ba1-xPbx)(Ti1-xSnx)O3 (BPTSx) (x = 0, 0.05, 0.10, 0.30) polycrystalline samples are presented. The samples were obtained by means of a high temperature synthesis and their expected stoichiometry was confirmed by energy dispersive spectroscopy (EDS) measurements. The dielectric properties of BPTSx were studied with the use of broadband dielectric spectroscopy. The...
-
Single-phase, Five-level Inverter with SPWM-Based Neutral Point Voltage Balancing Scheme
PublikacjaMultilevel inverter topologies provide several advantages over two-level inverter configuration. These benefits are the reason for the growing interest in multilevel topologies among research society. One of the most popular topological concepts (diode and active switch clamping) requires neutral-point potential balancing due to series-connected capacitor banks across the input dc link in such derived inverter configurations. This...
-
Niekorzystny wpływ przekształtnikowego zasilania PWM na silniki asynchroniczne trakcyjne
PublikacjaThe electric traction drives with an AC motor fed by a frequency converter are used more and more often nowadays. The most significant side effects, of a converter's output voltage forming PWM method for AC motor windings, are steep voltage changes, which can initiate several destructive phenomena. The paper presents the adverse influence of a converter common mode voltage on the motor windings' increased voltage exposure and the...
-
Destructive impact of PWM inverters on traction AC motors
PublikacjaThe electric traction drives with an AC motor fed by a frequency converter are used more and more often nowadays. The most significant side effects, of a converter's output voltage forming PWM method for AC motor windings, are steep voltage changes, which can initiate several destructive phenomena. The paper presents the adverse influence of a converter common mode voltage on the motor windings's increased voltage exposure and...
-
KEMR-Net: A Knowledge-Enhanced Mask Refinement Network for Chromosome Instance Segmentation
PublikacjaThis article proposes a mask refinement method for chromosome instance segmentation. The proposed method exploits the knowledge representation capability of Neural Knowledge DNA (NK-DNA) to capture the semantics of the chromosome’s shape, texture, and key points, and then it uses the captured knowledge to improve the accuracy and smoothness of the masks. We validate the method’s effectiveness on our latest high-resolution chromosome...
-
Destructive Consequences of PWM Inverter Feeding for Traction AC Motors
PublikacjaThe electric traction drives with an AC motor fed by a frequency converter are used more and more often nowadays. The most significant side effects, of a converter's output voltage forming PWM method for AC motor windings, are steep voltage changes, which can initiate several destructive phenomena. The paper presents the adverse influence of a converter common mode voltage on the motor windings' increased voltage exposure and the...
-
Interactive Query Expansion with the Use of Clustering by Directions Algorithm
PublikacjaThis paper concerns Clustering by Directions algorithm. The algorithm introduces a novel approach to interactive query expansion. It is designed to support users of search engines in forming web search queries. When a user executes a query, the algorithm shows potential directions in which the search can be continued. This paper describes the algorithm and it presents an enhancement which reduces the computational complexity of...