Filtry
wszystkich: 1938
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: GAS-STEAM CYCLES
-
Application of spatial neural simulators of turbine blade rows to fluid flow diagnostics
PublikacjaThis chapter presents the results of neural modelling of fluid flow in steam turbine row. In modelling working conditions of the flow channel varied, thus the aim of the work was to reconstruct the reference state - distributions of velocity, pressure, and losses in flow channel - with high accuracy for fluid flow diagnostics.
-
Cyclic voltammetry curves of the V2O5 nanorods (Na-ion batteries)
Dane BadawczeThe DataSet contains the next thirty cycles voltammetry curves for the V2O5 nanorods obtained by the sol-gel method. The cyclic voltammetry was measured using the AUTOLAB 302N potentiostat-galvanostat. The measurements were carried out in a voltage range of 2 V to 4 V vs. Na/Na+ at a scan rate of 1 mV/s. As an electrolyte 1M NaPF6 was applied.
-
Cyclic voltammetry curves of the V2O5 nanocrystals (Na-ion batteries)
Dane BadawczeThe DataSet contains the next thirty cycles voltammetry curves for the V2O5 nanocrystals obtained by the sol-gel method. The cyclic voltammetry was measured using the AUTOLAB 302N potentiostat-galvanostat. The measurements were carried out in a voltage range of 2 V to 4 V vs. Na/Na+ at a scan rate of 1 mV/s. As an electrolyte 1M NaPF6 was applied.
-
Toward Fast Calculation of Communication Paths for Resilient Routing
PublikacjaUtilization of alternate communication paths is a common technique to provide protection of transmission against failures of network nodes/links. However, a noticeable delay is encountered when calculating the relevant sets of disjoint paths using the available algorithms (e.g., using Bhandari’s approach). This, in turn, may have a serious impact on the ability of a network to serve dynamic demands...
-
Electrical conductivity of the Sr0.86Ti0.65Fe0.35O3-d pellet at different oxygen partial pressures
Dane BadawczeThis dataset contains results electrical conductivity measurements of dense Sr0.86Ti0.65Fe0.35O3-d (STF35) pellet. DC electrical conductivity measurements of STF35 were performed by the Van der Pauw method. Studies were performed at different oxygen partial pressures (20%, 1% and 0.1%) under humidified (~4 vol%) gas flow rate of 50 ml min -1.
-
Obrony prac doktorskich na Wydziale Chemicznym
WydarzeniaDn. 19.09.2022 r. o godz. 11.15 w Audytorium 1.4 Wydziału Chemicznego PG (budynek nr 5) odbędzie się w trybie hybrydowym publiczna obrona pracy doktorskiej mgr. inż. Maksymiliana Platy-Gryla.
-
Determination of carbonyl compounds in distilled alcoholic beverages using gas chromatography and head-space solid phase microextraction. Oznaczanie związków karbonylowych w napojach alkoholowych z użyciem chromatografii gazowej i mikroekstrakcji do fazy stacjonarnej z fazy nadpowierzchniowej
PublikacjaW pracy przedstawiono badania nad opracowaniem procedury oznaczania związków karbonylowych z użyciem mikroekstrakcji do fazy stacjonarnej w wersji analizy fazy nadpowierzchniowej (HS-SPME), chromatografii gazowej z detekcją wychwytu elektronów(GC-ECD) oraz derywatyzacji pentafluorobenzylohydroksyloaminą (PFBHA). Opisano wpływ parametrów: temperatury, mieszania, czasu ekspozycji włókna, dodatku soli, stężenia alkoholu. Opracowaną...
-
An O ( n log n ) algorithm for finding edge span of cacti
PublikacjaLet G=(V,E) be a nonempty graph and xi be a function. In the paper we study the computational complexity of the problem of finding vertex colorings c of G such that: (1) |c(u)-c(v)|>=xi(uv) for each edge uv of E; (2) the edge span of c, i.e. max{|c(u)-c(v)|: uv belongs to E}, is minimal. We show that the problem is NP-hard for subcubic outerplanar graphs of a very simple structure (similar to cycles) and polynomially solvable for...
-
Evaluation of the efficiency of the duty cycle of refuse collection vehicle based on real-world data
PublikacjaIn this paper a method of the efficiency evaluation of the duty cycle of Refuse Collection Vehicle is presented. Using real world data, two representative duty cycles were analysed. Total cycle efficiency was calculated, as well as the efficiency of particular cycle phases. Then, energy needed to collect and compact the waste and energy from fuel were compared. Measured and calculated values were shown on the diagrams illustrating...
-
Pracujący w czasie rzeczywistym system detekcji gazów wykorzystujący przenośny komputer Raspberry PI oraz matrycę półprzewodnikowych czujników gazu
PublikacjaThe gas-analyzing systems based on the array of partially selective gas sensors and pattern-recognition techniques are potentially fast and lowcost alternative for other devices, like gas‑analysers. They give the possibility of recognition the type and the concentration of measured volatile compounds in their working environment. In this work we present the implementation of gas recognition system, in which the signals from an...
-
Incorporation of the sulfur cycle in sustainable nitrogen removal systems - A review
PublikacjaIn wastewater treatment systems, sulfur (S) removal processes are generally based on heterotrophic sulfate (SO42−) reduction by sulfate reducing bacteria and S-dependent autotrophic denitrification by sulfur oxidizing bacteria. A combination of either two cycles (N and S) or three cycles (N, S and C) appears to be a viable approach to sustainable wastewater treatment, resulting in energy savings and reduction of sludge production....
-
The TPR reduction profile of Ce0.9M0.1O2
Dane BadawczeThe dataset includes the TPR reduction profiles of Ce0.9M0.1O2 (where M=Mn, Fe, Co, Ni, Cu) nanopowders prepared by the reverse microemulsion method. After the synthesis powders were dried, then calcined at 500 degrees for 2 h. The measurements were carried out in H2/Ar mixture from 100C to 900C. Gas flow:40ml/min and temperature ramp: 10deg/min.
-
Robert Aranowski dr inż.
Osoby -
Advanced operating methods
PublikacjaSelected operating methods of resistive gas sensors were presented. The methods utilize flicker noise (1/f noise), which gives additional information about ambient gas when compared with the recorded changes of DC resistance only. Methods of flicker noise measurements were outlined. Recently developed prototype gas sensors comprising golden nanoparticle functionalized with organic ligands can generate intense flicker noise induced...
-
Wstępne badania technologii spawania złączy narożnych ze stali niskoweglowej i nierdzewnej o grubości g=6mm i g=10mm
PublikacjaCelem pracy był dobór parametrów spawania dla spoin narożnych o grubości 6mm i 10mm próbek wykonanych ze stali niskowęglowej S355 i stali nierdzewnej - typu 304 (X6CrNI18-10). Złącza były spawane laserowo, jednostronnie z pełnym przetopem a powierzchnie lica i grani zapewniają uzyskanie szczelności przylegającego elementu uszczelniającego. Próbki zostały dostarczone przez Zleceniodawcę. Próby zostały przeprowadzone na stanowisku...
-
The Emission and Combustion Characteristics of Marine Diesel Engine with Extreme Throttled of Air or Exhaust Ducts
PublikacjaPresented paper shows the results of the laboratory tests on the relationship between the extreme throttling of both air intake duct and exhaust gas duct and gaseous emission from the marine engine. The object of research is a laboratory, 4-stroke, DI diesel engine, operated at loads from 50 kW to 250 kW at a constant speed equal to 750 rpm. During the laboratory tests the thermodynamic and exhaust gas emission characteristics...
-
TOXIC GASES IDENTIFICATION USING SINGLE ELECTROCATALYTIC SENSOR RESPONSES AND ARTIFICIAL NEURAL NETWORK
PublikacjaThe need for precise detection of toxic gases drives development of new gas sensors structures and methods of processing the output signals from the sensors. In literature, artificial neural networks are considered as one of the most effective tool for the analysis of gas sensors or sensors arrays responses. In this paper a method of toxic gas components identification using a electrocatalytic gas sensor as a detector and an artificial...
-
Zastosowanie połączenia mikroekstrakcji do fazy stacjonarnej i chromatografii gazowej do oznaczania lotnych kwasów tłuszczowych w próbkach środowiskowych i pokrewnych=Application of combination of solid phase microextraction and gas chromatography for determination of volatile fatty acids in environmental and related samples
PublikacjaOznaczanie lotnych kwasów tłuszczowych (LKT) w próbkach środowiskowych wymaga najczęściej izolacji i wzbogacania analitów na etapie przygotowania próbek oraz zastosowania techniki o dużym potencjale separacyjnym i identyfikacyjnym na etapie oznaczeń końcowych. W pracy dokonano krytycznego przeglądu zastosowań wygodnej i często stosowanej techniki mikroekstrakcji do fazy stacjonarnej (SPME) w połączeniu z wysokosprawną techniką...
-
Analytical and reliability data from the real-time simulator biogas plant
Dane BadawczeThe dataset represents the results of biogas plant simulation. The described plant is an agricultural biogas system, which can produce electrical energy with power estimated up to 1070 kW and heat energy that can reach 1200 kW simultaneously.
-
The effectivness of fault detection in common rail injectors examination methods
PublikacjaThe article presents the effectiveness tests of fault detection in common rail injectors. 40 injectors with different wear levels were tested. Testing was made on two test benches of a completely different design. Research includes comparison of accuracy, reproducibility and testability to detect specific defects. A device was created for visualization of the fuel injector spraying steam.
-
Complete input data to CFD 3D model of combustion in the large marine 4-stroke engine
Dane BadawczeInput data to CFD and 3D model of combustion process for large marine 4-stroke diesel engine.
-
Low temperature electrical conductivity of the SrFeO3-d pellet
Dane BadawczeThis dataset contains results of low temperature electrical conductivity measurements of dense SrFeO3-d (SFO) pellet. DC electrical conductivity measurements of SFO were performed by the Van der Pauw method between 400 °C and room temperature with 20 °C step. Studies were performed at Synthetic Air flow under humidified (~4 vol%) gas flow rate of 40...
-
Low temperature electrical conductivity of the SrTi0.65Fe0.35O3-d pellet
Dane BadawczeThis dataset contains results of low temperature electrical conductivity measurements of dense SrTi0.65Fe0.35O3-d (STF35) pellet. DC electrical conductivity measurements of STF35 were performed by the Van der Pauw method between 400 °C and room temperature with 20 °C step. Studies were performed at Synthetic Air flow under humidified (~4 vol%) gas...
-
Low temperature electrical conductivity of the SrTi0.30Fe0.70O3-d pellet
Dane BadawczeThis dataset contains results of low temperature electrical conductivity measurements of dense SrTi0.30Fe0.70O3-d (STF70) pellet. DC electrical conductivity measurements of STF70 were performed by the Van der Pauw method between 400 °C and room temperature with 20 °C step. Studies were performed at Synthetic Air flow under humidified (~4 vol%) gas...
-
Low temperature electrical conductivity of the SrTi0.50Fe0.50O3-d pellet
Dane BadawczeThis dataset contains results of low temperature electrical conductivity measurements of dense SrTi0.50Fe0.50O3-d (STF50) pellet. DC electrical conductivity measurements of STF50 were performed by the Van der Pauw method between 400 °C and room temperature with 20 °C step. Studies were performed at Synthetic Air flow under humidified (~4 vol%) gas...
-
Low temperature electrical conductivity of the SrTi0.10Fe0.90O3-d pellet
Dane BadawczeThis dataset contains results of low temperature electrical conductivity measurements of dense SrTi0.10Fe0.90O3-d (STF90) pellet. DC electrical conductivity measurements of STF90 were performed by the Van der Pauw method between 400 °C and room temperature with 20 °C step. Studies were performed at Synthetic Air flow under humidified (~4 vol%) gas...
-
Scanning electron microscopy (SEM) images of the boron-doped carbon nanowalls surfaces
Dane BadawczeThe dataset contains the scanning electron micrographs (SEM), revealing the surface morphology of boron-doped carbon nanowalls electrodes on silicon substrates. The surface is characterized by nano-walled structures. The obtained electrodes were doped with boron at the level of [B]/[C] = 5000ppm in the gas atmosphere during the synthesis.
-
Scanning electron microscopy (SEM) images of the boron-dopied carbon nanowalls surfaces
Dane BadawczeThe dataset contains the scanning electron micrographs (SEM), revealing the surface morphology of boron-doped carbon nanowalls electrodes on silicon substrates. The surface is characterized by nano-walled structures. The obtained electrodes were doped with boron at the level of [B]/[C] = 1200ppm in the gas atmosphere during the synthesis.
-
Scanning electron microscopy (SEM) images of the boron-doped carbon nanowalls surfaces
Dane BadawczeThe dataset contains the scanning electron micrographs (SEM), revealing the surface morphology of boron-doped carbon nanowalls electrodes on silicon substrates. The surface is characterized by nano-walled structures. The obtained electrodes were doped with boron at the level of [B]/[C] = 2000ppm in the gas atmosphere during the synthesis.
-
The phenomenon of increasing capacitance induced by 1T/2H-MoS2 surface modification with Pt particles – Influence on composition and energy storage mechanism
PublikacjaIn this paper, several approaches to the synthesis of molybdenum-based electrode materials for supercapacitors are presented, including anodization, hydrothermal process and annealing. For the material prepared via anodization of a molybdenum plate, followed by a hydrothermal process in thiourea aqueous solution, a thorough study of the Pt-surface modification through repetitive cycling in 1 M sulfuric acid with Pt acting as a...
-
Mechanical behaviour of knit synthetic mesh used in hernia surgery
PublikacjaPurpose: There is a discussion in literature concerning mechanical properties and modelling of surgical meshes. An important feature of elastic modulus dependency on load history is taken into account in this paper, as implants are subjected to variable loading during human activity. The example of DynaMesh®-IPOM surgical implant is studied. Methods: The analysis is based on failure tension tests and cyclic loading and unloading...
-
The impact of freeze-thaw processes on a cliff recession rate in the face of temperate zone climate change
PublikacjaFreeze-thaw action is a common type of geomorphological processes eroding cliff faces in the temperate climate zone. In our previous study, we assessed the geomorphological effects of freeze-thaw fluctuations occurring within the cliff of Jeziorsko Reservoir (central Poland). Based on those findings, we have now determined the number of freeze-thaw cycles to assess their historical impact on the studied cliff. We have also traced...
-
Operation of the 900 MW power plant with the ORC supplied from three heat sources
PublikacjaThe chapter is aimed at utilisation of waste heat in the reference supercritical power plant in the manner to produce electricity in ORC installation. The waste heat is available in the form of a stream of hot water at 90°C, recovered from the exhaust gases in the amount of 200MW. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. Therefore an original approach to increase...
-
Predicting cutting power for band sawing process of pine and beech wood dried with the use of four different methods
PublikacjaWood drying is an important stage in the woodworking process. After drying, wood is subject to a re-sawing process, for which a high quality surface, low material loss, and high efficiency are often required. In this paper, forecasted values were presented of cutting power for the re-sawing process of pine and beech wood that were dried with four different methods. Forecasting of cutting power for an industrial band saw machine...
-
Permeation and sorption properties of poly(ether-block-amide) membranesfilled by two types of zeolites
PublikacjaThe experimental study of transport properties of mixed matrix membranes (MMMs) based on PEBA-4033 with two types of zeolites is reported. Gas (CO2, O2, N2) and vapor (benzene, toluene, methanol, water) permeation measurements were performed using the differential flow permeameter at temperature of 298.15 K and at atmospheric pressure. Gas/vapor permeation was monitored by measuring the changes of the thermal conductivity of carrier...
-
The Effect of Steaming Beech, Birch and Maple Woods on Qualitative Indicators of the Surface
PublikacjaThis work presents the effect of steaming beech, birch and maple woods on the resulting quality of the milled wood surface. The steaming process of the studied woods results in a targeted change in the color of the wood, which changes from the original light white-gray color to fine reddishbrown to dark brown color shades that are more or less saturated depending on the temperature of the saturated water steam. The color changes...
-
Influence of cyclic frozen and defrost on mechanical properties of polytetrafluoroethylene (PTFE)-coated woven fabrics
PublikacjaThis research aims to determine the influence of the cyclic process of freezing and defrosting on the mechanical properties of the chosen glass fibres and PTFE-coated woven fabrics. The specimens were subjected to freezing at about −20 °C for 4 h and thawing by full immersion into the water at about +20 °C for 4 h. The fabric samples after 25 and 50 frozen cycles were air-dried at room temperature for one week and then subjected...
-
Widening of the electroactivity potential range by composite formation – capacitive properties of TiO2/BiVO4/PEDOT:PSS electrodes in contact with an aqueous electrolyte
PublikacjaComposites based on the titania nanotubes were tested in aqueous electrolyte as a potential electrode material for energy storage devices. The nanotubular morphology of TiO2 was obtained by Ti anodization. TiO2 nanotubes were covered by a thin layer of bismuth vanadate using pulsed laser deposition. The formation of the TiO2/BiVO4 junction leads to enhancement of pseudocapacitance in the cathodic potential range. The third component,...
-
Make lighting healthier
PublikacjaLife on Earth evolved in day-and-night cycles. Plants and animals, including insects such as the fruit fly, have a biological clock that controls their circadian rhythms — as the 2017 winners of the Nobel Prize in Physiology or Medicine showed. Now, humans’ increasing reliance on artificial lighting is changing those rhythms.
-
Zastosowanie metod eksploracji danych do analizy odpowiedzi czujników gazu
PublikacjaZagadnienia poruszane w niniejszej rozprawie dotyczą zastosowania metod eksploracji danych do analizy odpowiedzi czujników gazu, umożliwiających poprawną identyfikację składu mieszaniny gazowej w elektronicznych systemach rozpoznawania gazu. Elektroniczne systemy rozpoznawania gazu to urządzenia wykorzystujące czujniki gazu oraz odpowiednio dobrane metody analizy danych pomiarowych, zdolne do określenia składu mierzonej mieszaniny...
-
The SEM micrographs of the synergistic action between cavitation erosion and pitting corrosion on stainless steel 304
Dane BadawczeThe dataset contains Scanning Electron Micrographs of stainless steel AISI304 samples made after cavitation erosion-corrosion exposure using a vibratory transducer (in accordance with ASTM G32). The micrographs compare the topography of samples subjected to either cavitation erosion (in deionized water), pitting corrosion (in 8% FeCl3 solution, without...
-
FORECASTING BIOGAS FORMATION IN LANDFILLS
Publikacja: The aim of the present research was to develop a mathematical model for estimating the amount of viscous gas generated as a function of weather conditions. Due to the lack of models for predicting gas formation caused by sudden changes in weather conditions in the literature, such a model was developed in this study using the parameters of landfills recorded for over a year. The effect of temperature on landfill gas production...
-
Wybrane zagadnienia przepływowe turbiny gazowej pracującej w tłoczni gazu ziemnego.
PublikacjaW niniejszym artykule przedstawiono cieplno-przepływowe obliczenia turbiny gazowej, stanowiącej napęd sprężarki w tłoczni gazu ziemnego. Wartości parametrów wejściowych niezbędnych do przeprowadzenia obliczeń przyjęto na podstawie danych technicznych tłoczni zasilających polski odcinek gazociągu tranzytowego Jamał-Europa, w których pracują turbiny gazowe SGT-600 firmy Siemens, o mocy 25,3 MW.
-
Immobilized biocatalysts - useful tool for industrial processes
PublikacjaThe main goal of biomaterials immobilization is the industrial re-use of them for many reaction cycles. However, application of this technolgoy for full commercialization requires more experiments in this field. In this study thermostable beta-galactosidases from Ptrococcus woesei and Meiothermus ruber were taken as model proteins immobilized in alginate gel.
-
Advanced Control Structures of Turbo Generator System of Nuclear Power Plant
PublikacjaIn the paper a synthesis of advanced control structures of turbine and synchronous generator for nuclear power plant working under changing operating conditions (supplied power level) is presented. It is based on the nonlinear models of the steam turbine and synchronous generator cooperating with the power system. Considered control structure consists of multi-regional fuzzy control systems with local linear controllers, including...
-
Advanced Control Structures of Turbo Generator System of Nuclear Power Plant
PublikacjaIn the paper a synthesis of advanced control structures of turbine and synchronous generator for nuclear power plant working under changing operating conditions (supplied power level) is presented. It is based on the nonlinear models of the steam turbine and synchronous generator cooperating with the power system. Considered control structure consists of multi-regional fuzzy control systems with local linear controllers, including...
-
Mathematical model of the energy consumption calculation during the pine sawn wood (Pinus sylvestris L.) drying process
PublikacjaThe article presents the modification of the existing mathematical model to calculate energy consumption during conventional drying process. Apart from energy consumption the model permits to estimate the time of high-temperature drying process. The drying medium is air and superheated steam mixture. The obtained calculation results were compared with conducted experimental tests of drying square-edged sawn sapwood timber (Pinus...
-
Taguchi sensors under temperature modulation
PublikacjaSemiconductor gas sensors are widely used in gas- analyzing applications for various gas species determination due to their low cost and possibility to detect number of different gases. However, one of the main problems with such sensors is their lack of selectivity. To overcome this issue different ap- proaches can be used. One of them is the operation with sensor temperature modulation combined with dedicated data process- ing...
-
Determination of toxic gases based on the responses of a single electrocatalytic sensor and pattern recognition techniques
PublikacjaA response from an electrocatalytic gas sensor contains fingerprint information about the type of gas and its concentration. As a result, a single gas sensor can be used for the determination of different gases. However, information about the type of gas and its concentration is hidden in the unique shape of the current–voltage response and it is quite difficult to explore. One of the ways to get precise information about the measured...
-
Performance and emission characteristics of diesel engines running on gaseous fuels in dual-fuel mode
PublikacjaConventional fossil fuels are being substituted with alternative green fuels because of their greenhouse gas emissions and pollution problems, which pose a severe threat to the environment. Several studies have reported the usage of biodiesel and gaseous fuels in both single and dual-fuel modes. Gaseous fuels such as producer gas, biogas, syngas, and hydrogen produced from renewable biomass could potentially be used along with...