Wyszukiwarka
Filtry
wszystkich: 2130
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: TRAVELING WAVE DEVICES
-
Nonreciprocal Devices Utilizing Longitudinally Magnetized Ferrite Coupled Lines
PublikacjaThis chapter presents authors’ recent research on the nonreciprocal devices utilizing longitudinally magnetized ferrite coupled line (FCL) junction. The principle of operation of FCL junction is explained and the hybrid techniques of analysis are shown. Numerical and experimental results concerning the nonreciprocal devices utilizing the different configurations of FCL junctions are presented and discussed.
-
The effect of current delay angle on tripping of residual current devices
PublikacjaPower electronics converters applied in domestic or similar installations may utilize current delay (phase) angle control to change the level of transferred power. Due to application of such types of converters, earth fault current in the installation may be strongly distorted. The current distortion level depends on a value of current delay angle. This delay angle also influences the tripping threshold of residual current devices....
-
Devices and Methods of Measurements
Czasopisma -
IEEE CIRCUITS & DEVICES
Czasopisma -
PLASMA DEVICES AND OPERATIONS
Czasopisma -
Health monitoring services based on off-the-shelf mobile devices
PublikacjaDevelopment of health monitoring systems usually involves usage of dedicated devices with provided guarantees in terms of their reliability. Those devices raise the cost of the whole system, because of which such platforms are limited only to specific areas and constrained number of users. Usage of off-the- shelf devices could lower the cost and bring those systems to the masses. The paper covers possible uses of common off-the-shelf...
-
Testing the impact of simplifications adopted in models describing wave loads on ship
PublikacjaThe wave-ship system in naval architecture is generally assumed to be a linear one. This allows for the computation of a transfer function of ship response to waves including wave loads on ship. The transfer function and the wave spectral density function enable the development of the stochastic process of wave loads on ship, corresponding to the irregular wave generating that loads. If the mathematical models of wave load transfer...
-
Testing the impact of simplifications adopted in models describing wave loads on ship
PublikacjaThe wave-ship system in naval architecture is generally assumed to be a linear one. This allows for the computation of a transfer function of ship response to waves including wave loads on ship. The transfer function and the wave spectral density function enable the development of the stochastic process of wave loads on ship, corresponding to the irregular wave generating that loads. If the mathematical models of wave load transfer...
-
A new nethod for RTS noise of semiconductor devices identification
PublikacjaIn the paper, a new method, called the noise scatterin pattern method (NSP method), for random telegraph signal noise identyfication in the inherent noise of semiconductor devices is described. A block diagram of a noise measurement system based on the NSP method is presented. Examples of patterns of the NSP method are presented.
-
Mobile devices and computing cloud resources allocation for interactive applications
PublikacjaUsing mobile devices such as smartphones or iPads for various interactive applications is currently very common. In the case of complex applications, e.g. chess games, the capabilities of these devices are insufficient to run the application in real time. One of the solutions is to use cloud computing. However, there is an optimization problem of mobile device and cloud resources allocation. An iterative heuristic algorithm for...
-
Number of customers using only mobile devices (so-called "mobile only") - 2017
Dane BadawczeThe number of users who only use mobile devices is also growing (excluding access via desktop computers and people who manage to order current transactions in traditional bank branches). At the end of the fourth quarter 2017, there were 2.2 million such people - an increase by 434 thousand. compared to previous year.
-
Experimental and numerical analysis of wave propagation in ground anchors
PublikacjaThe article focuses on wave propagation phenomenon in ground anchors. The main aim of the investigation is the non-destructive diagnostics and the assessment of the state of ground anchors, using the guided wave propagation method. Laboratory models of anchors with different lengths of the anchor body were tested and voltage signals of propagating waves were registered at several locations. For all tested specimens corresponding...
-
A Finite Element Approach for Wave Propagation in Elastic Solids
PublikacjaThis book focuses on wave propagation phenomena in elastic solids modelled by the use of the finite element method. Although the latter is a well-established and popular numerical tool used by engineers and researchers all around the word the process of modelling of wave propagation can still be a challenge. The book introduces a reader to the problem by presenting a historical background and offering a broad perspective on the...
-
Measuring research on radio wave propagation
PublikacjaTelecommunication connections are increasingly based on the wireless links, both fixed and mobile, carried out under different radio systems. This kind of solution has many advantages. However, the propagation medium is a factor that causes many difficulties in designing wireless networks, because of large diversity of propagation environments. Transmission loss in each environment is determined by many variables phenomena and...
-
Experiences from operation of various expansion devices in small scale ORC
PublikacjaThe main aim of this paper was to present various expansion devices for an application in the small scale ORC system. The investigations were carried out in two parallel directions. One direction was to design and construct a device dedicated to the analyzed ORC system. The second direction was to adapt existing expansion devices for the needs of the analyzed ORC system. Four various devices were described and presented together...
-
Guided wave propagation in diagnostic of steel elements
PublikacjaThis paper is devoted to numerical investigations of elastic wave propagation in steel elements. The aim of this study is to conduct numerical analysis and experimental investigations on the propagation of elastic waves in steel elements in the context of damage detection. In particular, this paper is devoted to detection of damage occurring in the form of notch or changed thickness. This approach utilized the fact that any discontinuities...
-
Guided wave propagation in diagnostic of steel elements
PublikacjaThis paper is devoted to numerical investigations of elastic wave propagation in steel elements. The aim of this study is to conduct numerical analysis and experimental investigations on the propagation of elastic waves in steel elements in the context of damage detection. In particular, this paper is devoted to detection of damage occurring in the form of notch or changed thickness. This approach utilized the fact that any discontinuities...
-
Study of Photovoltaic Devices with Hybrid Active Layer
PublikacjaThe aim of this work is to present the influences of composition of the material andmanufacturing technology conditions of the organic photovoltaics devices (OPv) with the organicand hybrid bulk heterojunction on the active layers properties and cells performance. The layers wereproduced by using small molecular compounds: the metal-phthalocyanine (MePc) and perylenederivatives (PTCDA) and the titanium dioxide (TiO2) nanoparticles....
-
Residual current devices in installations with PV energy sources
PublikacjaThe paper presents the principles of residual current devices (RCDs) application in photovoltaic (PV) installations. Provisions of standards in this regard are commented on, in particular, attention is drawn to the lack of obligation to use of RCDs in PV installations. The issue of the shape of the earth fault current and the level of leakage currents in such installations are discussed. These factors influence the selection of...
-
Investigation of continuous wave jamming in an IEEE 802.15.4 network
PublikacjaThis paper presents how continuous wave jamming affects IEEE 802.15.4 network. To this end, an office-based measurement setup has been proposed. Within the measurement area, 25 nodes have been set up in order to create a IEEE 802.15.4 tree-based test network structure. A dedicated jamming device that generates and transmits a continuous wave signal has been developed. Several tests have been conducted and presented to demonstrate...
-
Towards Contactless, Hand Gestures-Based Control of Devices
PublikacjaGesture-based intuitive interactions with electronic devices can be an important part of smart home systems. In this paper, we adapt the contactless linear gesture sensor for the navigation of smart lighting system. Set of handled gestures allow to propose two methods of active light source selection, continuous dimming, and turning on and off based on discrete gestures. The average gesture recognition accuracy was 97.58% in the...
-
Application of auto calibration and linearization algorithms to improve sound quality of computer devices
PublikacjaAn application of auto calibration and linearization algorithms designed for correcting acoustic characteristics of selected computer devices was presented in the paper. The functionality of the algorithms were presented for two kind of computer devices: ultrabook class computer and portable device of All-In-One type. The algorithms were adjusted for the given type of the device on the basis of series of measurements conducted...
-
Protonic Ceramic Fuel Cells as novel electrochemical devices
PublikacjaProton ceramic conductors are novel materials which are interesting from the application point of view. For example, Protonic Ceramic Fuel Cells (PCFCs) is a type of a solid oxide fuel cell, which uses proton ceramic conductors as an electrolyte. Scientists are looking for the most efficient materials for these devices. In recent years main focus has been put on the search for new proton and mixed proton-electron conductors which...
-
Energy consumption estimation of low-power devices using an integrating coulombmeter
PublikacjaThe main problem in designing devices powered with Energy Harvesting is an estimation of energy demand of low-power devices as well as quantity of energy provided by the selected energy transducer in the assumed work conditions. Due to the work characteristic of each block of the device and properties of the measured signal, measurement is not trivial. The paper presents the proposal of the micro-charge measurement device based...
-
Remarks on the Subject of Back-Up Protection of Residual Current Devices
PublikacjaResidual current devices without integral overcurrent protection (RCCBs) are back-up protected by fuses or miniature circuit-breakers (MCBs). If the latter are used, special attention must be given to the coordination between an RCCB and an MCB. This paper indicates probable cases of the aforementioned devices coordination, in which back-up protection of the RCCB is not adequate. A laboratory test has shown that depending on the...
-
Application of guided wave propagation in diagnostics of steel bridge components
PublikacjaEarly detection of potential defects and identification of their location are necessary to ensure safe, reliable and long-term use of engineering structures. Non-destructive diagnostic tests based on guided wave propagation are becoming more popular because of the possibility to inspect large areas during a single measurement with a small number of sensors. The aim of this study is the application of guided wave propagation in...
-
Design and Evaluation of the Compact and Autonomous Energy Subsystem of a Wave Energy Converter
PublikacjaThis paper presents the results of the design process focused on the development of the energy subsystem (ES) of a wave energy converter (WEC). The ES is an important electrical part that significantly affects the energy reliability and energy efficiency of the entire WEC device. The designed ES was intended for compact WECs powering IoT network devices working in the distributed grid. The developed ES is an electronic circuit...
-
Noise in semiconductor devices
PublikacjaOmówiono typowe źródła szumów występujące w przyrządach pólprzewodnikowych, a mianowicie: cieplne, śrutowe, generacyjno-rekombinacyjne, 1/f, 1/f2, wybuchowe (RTS), lawinowe. Przedstawiono szumowe schematy zastępcze tranzystora bipolarnego, JFET i MOSFET oraz opisano wydajności poszczególnych źródeł szumów. Zasugerowano jak dobierać przyrządy półprzewodnikowe do małoszumowych układów w zakresie małych częstotliwości.
-
Waves Along Fractal Coastlines: From Fractal Arithmetic to Wave Equations
PublikacjaBeginning with addition and multiplication intrinsic to a Koch-type curve, we formulate and solve wave equation describing wave propagation along a fractal coastline. As opposed to examples known from the literature, we do not replace the fractal by the continuum in which it is embedded. This seems to be the first example of a truly intrinsic description of wave propagation along a fractal curve. The theory is relativistically...
-
An Efficient PEEC-Based Method for Full-Wave Analysis of Microstrip Structures
PublikacjaThis article introduces an efficient method for the equivalent circuit characterization and full-wave analysis of microstrip structures, leveraging the full-wave partial element equivalent circuit (PEEC). In particular, the multilayered Green's function is evaluated using the discrete complex-image method (DCIM) and employed to establish the mixed potential integral equations. The proposed strategy considers time delays for the...
-
Analysis of ship's magnetic field with consideration of inner ferromagnetic devices
PublikacjaThis paper presents computer simulations of ship’s magnetic signatures. The influence of ship’s inner ferromagnetic devices on the signature was presented. The magnetic fields of the ship’s model were calculated in Opera 3D 18R2. The model was built from thin plates. The new, thin plate boundary condition was introduced on all ship’s surfaces.
-
Plasma models, contribution matrix for detector setup and generated projections for plasma emissivity reconstruction in fusion devices
Dane BadawczeThe original plasma models for fusion devices, together with the complementary detector setup in the form of a contribution matrix and generated projections. Samples are packed inside a Plasma Tomography Format (PTF) files which is a part of the Plasma Tomography in Fusion Devices Python package, and inside the general JSON format. The constructed dataset...
-
Numerical Study of Concrete Mesostructure Effect on Lamb Wave Propagation
PublikacjaThe article presents the results of the numerical investigation of Lamb wave propagation in concrete plates while taking into account the complex concrete mesostructure. Several concrete models with randomly distributed aggregates were generated with the use of the Monte Carlo method. The influence of aggregate ratio and particle size on dispersion curves representing Lamb wave modes was analyzed. The results obtained for heterogeneous...
-
Immunity of residual current devices to the impulse leakage current in circuits with variable speed drives
PublikacjaThis paper concerns reliability of supply in variable speed drive circuits with residual current devices. During normal operation of these circuits high value of leakage current causes unwanted tripping of residual current devices. Immunity of residual current devices to the impulse leakage current should be evaluated. The system for testing of residual current devices and results of the test are presented
-
MATERIALS FOR ENERGY STORAGE AND CONVERSION DEVICES
Kursy Online -
Materials for energy storage and conversion devices
Kursy Onlinelecture course (Eng) 15h
-
Simulation of Wave Propagation in Media Described by Fractional-Order Models
PublikacjaIn this paper, algorithms for simulation of the wave propagation in electromagnetic media described by fractional-order (FO) models (FOMs) are presented. Initially, fractional calculus and FO Maxwell's equations are introduced. The problem of the wave propagation is formulated for media described by FOMs. Then, algorithms for simulation of the non-monochromatic wave propagation are presented which employ computations in the time...
-
Identification of inherent noise components of semiconductor devices on an example of optocouplers
PublikacjaIn the paper, a method of estimation of parameters of Gaussian and non-Gaussian components in the noise signal of semiconductor devices in a frequency domain is proposed. The method is based on composing estimators of two spectra, corresponding to noise (Gaussian component) and two-level RTS noise (non-Gaussian component). The proposed method can be applied for precise evaluation of the corner RTS frequency fRTS in the noise...
-
Baseline-free debonding detection in reinforced concrete structures by elastic wave propagation
PublikacjaThe article presents the results of the numerical and experimental analysis concerning wave propagation in reinforced concrete (RC) beams with various extent of debonding between the steel rod and concrete cover. The main aim of the paper was to consider the unsolved research gaps, which considerably limit the application of wave-based methods in practice. The propagation of the flexural wave modes excited and registered on the...
-
Quality of graphical markers for the needs of eyewear devices
Publikacjain this paper we propose to cast the problem of identification of people, objects or places into an application for smart glasses that decodes information from graphical markers. We focus on analyzing different factors that can have influence on the processes of the automatic recognition of information from a code. The research we present aims at reviewing recognition performances in function of: size of a marker, distance from/to...
-
Behavior of residual current devices at frequencies up to 50 kHz
PublikacjaThe use of residual current devices (RCDs) is obligatory in many types of low-voltage circuits. They are devices that ensure protection against electric shock in the case of indirect contact and may ensure additional protection in the case of direct contact. For the latter purpose of protection, only RCDs of a rated residual operating current not exceeding 30 mA are suitable. Unfortunately, modem current-using equipment supplied...
-
Damage localisation in a stiffened plate structure using a propagating wave
PublikacjaThe paper presents an application of changes in propagating waves for damage detection in a stiffened aluminium plate. The experimental investigation was conducted on an aluminium plate with riveted two L-shape stiffeners. The wave has been excited with a piezoelectric transducer and measured with the Laser Scanning Doppler Vibrometer. Recorded signals were analysed using the special signal processing techniques developed for damage...
-
IEEE Microwave and Guided Wave Letters
Czasopisma -
Simulations of wave propagation and attenuation in fields of colliding ice floes
Dane BadawczeThis dataset contains results of numerical smulations of sea ice-wave interactions, corresponding to laboratory experiments conducted at the Large Ice Model Basin (LIMB) at the Hamburg Ship Model Basin (HSVA) as part of the LS-WICE ("Loads on Structure and Waves in Ice"; https://zenodo.org/record/1067170#.XrLt_dhpxhE) project. THe simulations were conducted...
-
INTERNATIONAL JOURNAL OF NUMERICAL MODELLING-ELECTRONIC NETWORKS DEVICES AND FIELDS
Czasopisma -
Photovoltaic properties of cadmium selenide–titanyl phthalocyanine planar heterojunction devices
PublikacjaPhotovoltaic phenomenon taking place in cadmium selenide (CdSe)/titanyl phthalocyanine (TiOPc) planar heterojunction devices is described. Mechanisms of free charge carrier generation and their recombination in the dark and under illumination are analyzed, chosen photovoltaic parameters are presented.
-
Non-destructive inspection of ground anchors using guided wave propagation
PublikacjaThis paper deals with numerical and experimental investigations of specific problems of guided wave propagation in ground anchors. The research focuses on recognizing the phenomenon of the energy transfer between anchor components. Particular attention is paid to characteristic features of guided waves propagating in free and embedded parts of the tendon, at the interface between the tendon and the surrounding anchor body as well...
-
Interactive Application for Visualization of the Basic Phenomena in RF and Microwave Devices
PublikacjaAn interactive computer application visualizing the basic phenomena in RF and microwave devices is presented. Such kind of educational package can be a very helpful tool for the students as well as for the teachers (of electronics and related fields). This paper is focused on three exemplary problems only and involves: movement of electric charge, filtering of electromagnetic waves and interference phenomena in antenna arrays. The...
-
Nonlinear Excitation of the Non-Wave Perturbations by the Magnetoacoustic Waves in the Non-Isentropic Plasma
PublikacjaNonlinear excitation of slow modes by the planar magnetosonic perturbations in a plasma is discussed. Plasma is an open system due to radiation and external heating. This may stipulate enhancement of wave perturbations and hence the acoustical activity of plasma. Plasma is assumed to be a homogeneous ideal gas with infinite electrical conductivity. The straight magnetic field is orthogonal to the velocity of fluid’s...
-
Fast Full-Wave Multilevel Zero-Pole Optimization of Microwave Filters
PublikacjaA new concept is proposed for the full-wave computer-aided design of microwave filters. The method consists of two stages and operates on the zeros and poles of the transfer function and their derivatives. These quantities are evaluated from the response computed by a full-wave electromagnetic solver with two levels of accuracy. The two stages make use of different models that are optimized using a low-accuracy electromagnetic...