Wyszukiwarka
Wyniki wyszukiwania dla: (li-s) batteries, porous carbon, biomass
-
Techno-economic analysis of a hybrid energy system for electrification using an off-grid solar/biogas/battery system employing HOMER: A case study in Vietnam
PublikacjaThe electrification of off-grid /island villages is a critical step towards improving the techno-economic circumstances of rural regions and the overall general growth of the country. However, consistent supply from a single source is not possible in these areas. Thus, a hybrid renewable energy system performs better in these conditions. The research challenge now is to identify the optimal combinations of HRES from the available...
-
Silicon Oxycarbide (SiOC) Ceramic Materials as Anodes for Lithium Ion Batteries
PublikacjaPolymer derived ceramics (PDCs) have attracted attention as alternative anode material for Li-ion batteries. It has been found that ternary SiOC and SiCN ceramics obtained through pyrolysis of various preceramic polymers display high reversible capacities of 500 – 650 mAh/g. In this work we try to correlate the electrochemical performance of polymer derived silicon oxycarbide with its chemical composition and microstructural features....
-
Miscanthus × giganteus growth and photosynthetic rate measurements
Dane BadawczeThis data set contains the findings of the growth development, gas exchange, and specific leaf area of the plants during the experiment in which straw and wood chips-based biochars were used as soil amendment for Miscanthus × giganteus (M×g) cultivation.
-
Electrochemistry from first-principles in the grand canonical ensemble
PublikacjaProgress in electrochemical technologies, such as automotive batteries, supercapacitors, and fuel cells, depends greatly on developing improved charged interfaces between electrodes and electrolytes. The rational development of such interfaces can benefit from the atomistic understanding of the materials involved by first-principles quantum mechanical simulations with Density Functional Theory (DFT). However, such simulations are...
-
A novel approach for processing CaAlSiON glass-ceramics by spark plasma sintering: Mechanical and electrical properties
PublikacjaLithium containing glassy materials can be used as solid electrolytes or electrode materials for lithium-ion batteries due to their high energy density. Conventional melt-quenched Ca11Al14Si16O49N10 glass powder containing 24 e/o N, doped with Li-ions (1, 3, and 6 wt. %) and sintered by spark plasma sintering technique (SPS) was studied. The benefits of using SPS to produce glass-ceramics are rapid heating rates compared to conventional...
-
N-doped carbon materials as electrodes for highly stable supercapacitors
PublikacjaThis article reports a strategy to use nitrogen-doped carbon materials as electrodes for supercapacitors. Depending on the carbon precursor, the porous structure is changed with specific surface area reached up to 2270 m2 g−1. The capacitance of carbon materials used as electrodes is related strictly to pore size. The microstructure and nitrogen functionalities enable a high capacitance (327 F g−1) and cycle durability. The nanoporous...
-
The application of moving bed biofilm reactor to denitrification process after trickling filters
PublikacjaThe paper presents research of a prototype moving bed biofilm reactor (MBBR). The device was used for the post-denitrification process and was installed at the end of a technological system consisting of a septic tank and two trickling filters. The concentrations of suspended biomass and biomass attached on the EvU Perl moving bed surface were determined. The impact of the external organic carbon concentration on the denitrification...
-
Comparison of the Effects of Conventional and Alternative External Carbon Sources for Enhancing of the Denitrification Process
PublikacjaFood industry effluents are considered a potential alternative for methanol when seeking external carbon sources to enhance denitrification in municipal wastewater treatment plants (WWTPs). The aim of this study was to determine the immediate effects of dosing different carbon sources on the denitrification capability of process biomass from the "Wschod" WWTP in Gdansk (northern Poland). Five carbon sources, including settled wastewater,...
-
The metabolic activity of denitrifying microorganisms accumulating polyphosphate in response to addition of fusel oil
PublikacjaThe effect of distillery waste product (fusel oil) as an alternative external organic carbon source (EOCS) was investigated in terms of the metabolic properties of denitrifying polyphosphate accumulating organisms (DPAOs). Samples of the non-acclimated biomass were collected from a local full-scale wastewater treatment plant employing A2/O type bioreactors. The acclimated biomass was obtained after cultivation (with fusel oil added)...
-
Silica-templated three-dimensional graphene xerogels
PublikacjaMost porous carbons require the uniform pore size distribution therefore many approaches have been applied to template the carbon scaffolds and among them the use of silica particles is the easiest and the most effective. After discovering of graphene, the whole family of new carbon nanomaterials arose and one of the promising materials is graphene xerogel (GX) with a three-dimensional, highly porous structure. This monograph reviews...
-
Review—Advances in Rechargeable Lithium-Ion Batteries Utilizing Polyoxometalate-Functionalized Nanocarbon Materials
PublikacjaPolyoxometalates (POMs) are inorganic nanoclusters that consist of oxygen and transition metals. These nanoclusters serve as excellent precursors for creating electrode materials that contain transition metals. Additionally, the interaction between POMs and carbon substrates produces positive synergistic effects. There has been considerable attention on employing POMs and carbon nanostructures (for example carbon nanotubes, graphene,...
-
SILICA AEROGEL TOWARDS ANODES FOR LITHIUM-ION BATTERIES
PublikacjaAn increasing demand for electrochemical energy storage and conversion devices stimulates progress in research on electrode and electrolyte materials. In the field of electrodes materials, silicon is the one of the most promising anode materials for Li-ion batteries. However silicon has the drastic volume variation (around 3 times lower on extraction) during insertion and extraction of lithium ions. As an alternative, nanocomposites...
-
A distillery by-product as an external carbon source for enhancing denitrification in mainstream and sidestream treatment processes
PublikacjaThe use of fusel oil as an 'alternative' carbon source for denitrification in the mainstream and sidestream treatment processes was studied. Research comprised two kinds of batch experiments as well as acclimation of process biomass to external carbon sources. In the conventional nitrate utilization rate (NUR) measurements (one-phase experiments with non-acclimated biomass), the NUR with fusel oil was 1.4-1.7 g N/(kg VSS•h which...
-
Negative CO2 Emission Gas Power Plant As Technology for Utilization of Sewage Sludge, Production of Electrical Energy, and CO2 Capture - Case of Chamber Under Transpiration Cooling
PublikacjaThis work focuses on the concept developed in the nCO2PP project, which aims to demonstrate a technology that allows to achieve negative CO2 emissions through Carbon Capture and Storage (CCS) applied to sewage sludge. A feedstock is first gasified, then the resulting syngas is burned in a semi-closed oxy-fuel gas turbine with pure oxygen and water, using the advantages of oxy-combustion, to ease the capture of CO2 in the resulting...
-
Pressure in charge. Neglected parameter in hydrothermal synthesis turns out to be crucial for electrochemical properties of ammonium vanadates
PublikacjaAmmonium vanadates are of great interest as they exhibit unusual electrical and sensory properties.(NH4)2V6O16and (NH4)2V10O25$8H2O with various morphology were obtained in the hydrothermalsynthesis under controlled temperature and pressure. It was shown, that the pure (NH4)2V10O25$8H2Owas obtained under 50 bar of initial pressure, whereas lower pressure lead to the mixture of twocompounds. The influence of the pressure was studied...
-
Battery Technologies in Electric Vehicles: Improvements in Electric Battery Packs
PublikacjaRestrictions on fossil fuels and related environmental pollution issues motivate many organizations and countries to set their focus on electric vehicles (EVs) rather than conventional internal combustion engine vehicles [1], [2]. EVs require an energy storage system to store converted electric power in another form of energy and then reconvert the stored energy to electric power whenever it is required. The energy stored can be...
-
Biosilica from sea water diatoms algae—electrochemical impedance spectroscopy study
PublikacjaHere, we report on an electrochemical impedance study of silica of organic origin as an active electrode material. The electrode material obtained from carbonized marine biomass containing nanoporous diatoms has been characterised by means of XRD, IR, SEM and EIS. Dif- ferent kinds of crystallographic phases of silica as a result of thermal treatment have been found. The electrode is electrochemically stable during subsequent cyclic...
-
Multifunctional catalyst-assisted sustainable reformation of lignocellulosic biomass into environmentally friendly biofuel and value-added chemicals
PublikacjaRapid urbanization is increasing the world's energy demand, making it necessary to develop alternative energy sources. These growing energy needs can be met by the efficient energy conversion of biomass, which can be done by various means. The use of effective catalysts to transform different types of biomasses will be a paradigm change on the road to the worldwide goal of economic sustainability and environmental protection. The...
-
Local Structure and Stability of SEI in Graphite and ZFO Electrodes Probed by As K-edge Absorption Spectroscopy
PublikacjaThe evolution of the solid electrolyte interphase (SEI) during the first Li uptake in advanced Li-ion electrodes is studied by X-ray absorption spectroscopy (XAS). The As atoms present in the electrolyte solution were used as a local probe for monitoring the SEI growth on different electrodes. High-quality As K-edge spectra were collected in fluorescence mode for a set of graphite and carbon-coated ZnFe2O4 electrodes. XAS measurements...
-
Production of fuel briquette from solid waste biomass using natural resin as a binder
PublikacjaBackground: This research aimed to evaluate the use of natural resin as a binder for the production of fuel briquette from solid waste biomass.Methods: Proximate analyses were made for fuel briquette prepared from solid waste biomass using natural resin as a binder in comparison with using starch as a binder.Results: The results for density, percent content of moisture, percent content of volatile matter, percent...
-
Production of fuel briquette from solid waste biomass using natural resin as a binder
PublikacjaAbstract Background: This research aimed to evaluate the use of natural resin as a binder for the production of fuel briquette from solid waste biomass. Methods: Proximate analyses were made for fuel briquette prepared from solid waste biomass using natural resin as a binder in comparison with using starch as a binder. Results: The results for density, percent content of moisture, percent content of volatile matter, percent content...
-
Electrochemical behavior of a composite material containing 3D-structured diatom biosilica
Publikacja3D-structured diatom biosilica mixed with conducting carbon black was investigated as an active electrode material for lithium-ion batteries. Diatom biosilica was obtained by cultivation of the selected diatom species under laboratory conditions. Several instrumental techniques (XRD, FTIR, Raman, SEM-EDX, TGA) were used to characterize the physicochemical properties of applied biosilica. It was evidenced that the prepared new composite...
-
Polymer derived SiOC/Sn nanocomposites from a low-cost single source precursor as anode materials for lithium storage applications
PublikacjaMetal- based materials capable of lithium (Li) alloy formation are key to realization of the next generation of high-energy density anodes for Li-ion batteries, owing to their high storage capacity. Designing a good sup- porting matrix is essential for homogeneously nesting these metallic nanodomains, to effectively utilize their high capacity while tackling the volume expansion issues. Silicon oxycarbides (SiOC), obtained via...
-
From ashes to porous hierarchical nanocarbon electrode: Upcycling secondary waste materials through self-catalytic chemical vapour deposition
PublikacjaMetal and metal oxide particles are abundant in various ash-based wastes. Utilizing these as catalyst sources for the fabrication of carbon nanomaterials could present a valuable approach to reduce our reliance on non-renewable and costly catalyst sources, thereby facilitating large-scale nanomaterial production. In this context, secondary waste materials (SWMs) are by-products resulting from the (complete or partial) combustion...
-
Synergistic effects of nitrogen-doped carbon and praseodymium oxide in electrochemical water splitting
PublikacjaHybrid materials featuring perovskite-type metal oxide in conjunction with heteroatom-doped graphene hold immense promise as alternatives to costly noble metal catalysts for electrochemical water splitting, facilitating the generation of environmentally friendly hydrogen. In this study, perovskite-type oxide containing praseodymium, barium, strontium, cobalt, and iron atoms dispersed in a carbon matrix as a catalyst is synthesized...
-
A negative effect of carbon phase on specific capacity of electrode material consisted of nanosized bismuth vanadate embedded in carbonaceous matrix
PublikacjaLithium-ion batteries (LIBs) are widely used all over the world. The LIBs belong to a renewable energy source and energy storage devices. The increase in energy demand causes that new materials of higher energy and higher power densities are still under investigation. Herein, we compare electrochemical properties of bismuth vanadate (BiVO4) embedded and not embedded into carbonaceous matrix as an anode material along with structural...
-
Composites of tin oxide and different carbonaceous materials as negative electrodes in lithium-ion batteries
PublikacjaAbstract Tin and tin oxide have been considered as suitable materials with high theoretical capacity for lithium ion batteries. Their low cost, high safety and other technical benefits placed them as promising replacements for graphite negative electrodes. The problem to overcome with tin oxide, as well as with other metallic materials, is high volume changes during alloying/dealloying, subsequent pulverization, delamination from...
-
Comparison of Properties of the Hybrid and Bilayer MWCNTs—Hydroxyapatite Coatings on Ti Alloy
PublikacjaCarbon nanotubes are proposed for reinforcement of the hydroxyapatite coatings to improve their adhesion, resistance to mechanical loads, biocompatibility, bioactivity, corrosion resistance, and antibacterial protection. So far, research has shown that all these properties are highly susceptible to the composition and microstructure of coatings. The present research is aimed at studies of multi-wall carbon nanotubes in three different...
-
The biotic and abiotic mercury at the coastal zone of Gulf of Gdańsk
Dane BadawczeConcentration of neurotoxin Hg (mercury) was determined monthly form 01.2012 to 05.2013 (total and suspended) in the surface microlayer and the surface water as well as in: phytoplankton, zooplankton, epilithon, epifithon, phytobenthos (macroalgae and angiosperms), zoobenthos, and in the sediment. The study was conducted in the coastal zone of the Puck...
-
Materiał węglowy ptrzymany na bazie karbonizowanego chitozanu domieszkowanego platyną = CARBON MATERIAL RECEIVED THROUGH CARBONIZATION OF CHITOSAN DOPED WITH PLATINUM
PublikacjaThe aim of this work was to investigate the impact of porous carbons with high nitrogen content onthe platinum catalyst performance properties. The system may be applied as well as cathodic catalyst for oxygenreduction in microbial fuel cells.We report a simple route for preparation of dispersed Platinum on the carbon support. Chitosan powder wasprotonated using aqueous solution of organic acid. The water from the pores was removed...
-
N-doped mesoporous carbon nanosheets obtained by pyrolysis of a chitosan–melamine mixture for the oxygen reduction reaction in alkaline media.
PublikacjaBy simple thermal decomposition of low-cost precursors (chitosan, melamine) in an inert atmosphere, nitrogen-doped porous carbonaceous materials were prepared. The samples pyrolyzed at 700 C are composed of mainly mesoporous nitrogen-doped carbon nanosheets and partially graphitized carbon. The nanosheets contain a disordered area due to the strain imposed by the presence of nitrogen and/or oxygen groups in their structure. Some...
-
Microporous N-Doped Carbon Obtained from Salt Melt Pyrolysis of Chitosan toward Supercapacitor and Oxygen Reduction Catalysts
PublikacjaThe direct carbonization of low-cost and abundant chitosan biopolymer in the presencesalt eutectics leads to highly microporous, N-doped nanostructures. The microporous structureeasily manufactured using eutectic mixture (ZnCl2 -KCl) and chitosan. Potassium ions here can act as an intercalating agent, leading to the formation of lamellar carbon sheets, whereas zinc chloride generates significant porosity. Here, we present an efficient...
-
Material Design and Optimisation of Electrochemical Li-Ion Storage Properties of Ternary Silicon Oxycarbide/Graphite/Tin Nanocomposites
PublikacjaIn this work, we present the characterization and electrochemical performance of various ternary silicon oxycarbide/graphite/tin (SiOC/C/Sn) nanocomposites as anodes for lithium-ion batteries. In binary SiOC/Sn composites, tin nanoparticles may be produced in situ via carbothermal reduction of SnO2 to metallic Sn, which consumes free carbon from the SiOC ceramic phase, thereby limiting the carbon content in the final ceramic nanocomposite....
-
Efficiency of landfill leachate treatment in a MBR/UF system combined with NF, with a special focus on phthalates and bisphenol A removal
PublikacjaIn this study, a pilot-scale membrane bioreactor (MBR) was operated at a municipal solid waste plant (MSWP) to treat a mixture of landfill leachates (LLs) obtained from modern (MP-LLs) and previous (PP-LLs) waste cells. The MBR unit combined anoxic and aerobic zones with external ultra- and nanofiltration (MBR/UF and MBR/UF/NF, respectively). In addition to the removal of macropollutants, special attention was given to phthalates...
-
Effects of different external carbon sources and electron acceptors on interactions between denitrification and phosphorus removal in BNR processes
PublikacjaThe effects of two different external carbon sources (acetate, ethanol) and electron acceptors (dissolved oxygen, nitrate and nitrite) were investigated under aerobic and anoxic conditions with non-acclimated process biomass from a full-scale biological nutrient removal activated sludge system. When acetate was added as an external carbon source, phosphate release was observed even in the presence of electron acceptors. The release...
-
Properties of LiMnBO3 glasses and nanostructured glass-ceramics
PublikacjaPolycrystalline LiMnBO3 is a promising cathode material for Li-ion batteries. In this work, we investigated the thermal, structural and electrical properties of glassy and nanocrystallized materials having the same chemical composition. The original glass was obtained via a standard melt-quenching method. SEM and 7Li solid-state NMR indicate that it contains a mixture of two distinct glassy phases. The results suggest that the...
-
Mercury in various components of the environment (Gulf of Gdańsk, southern Baltic Sea)
PublikacjaTotal mercury concentration was determined monthly form January 2012 to May 2013 in the water (microlayer and the surface), plankton, epilithon, epiphyton, benthos and sediment. The study was conducted in the coastal zone of the Gulf of Gdańsk. The abundance and biomass of plankton, benthos; the concentration of suspended particulate matter, particulate organic carbon and nitrogen; δ13C and δ15N in the suspended matter; sediment...
-
Gasification of Densified Biomass (DB) and Municipal Solid Wastes (MSW) Using HTA/SG Technology
PublikacjaThe necessity of economical and rational use of natural energy sources caused a rapid development of research on the possibilities of using non‐conventional energy resources. Taking the above into account, a new technological process of thermochemical conversion of biomass and communal waste, commonly known as High Temperature Air/Steam Gasification (HTA/SG) and Multi‐Staged Enthalpy Extraction Technology (HTAG‐MEET), was developed....
-
Distillery Wastes as External Carbon Sources for Denitrification in Municipal Wastewater Treatment Plants
PublikacjaIn order to improve efficiency of N removal within the existing capacities, the denitrification process can be enhanced by adding external carbon sources. The studies on utilization of various by-products or waste materials as alternative carbon sources for denitrification have been carried out for over 20 years (Sage et al. 2006). Among several commercially available organic compounds (such as methanol, ethanol, acetic acid, glucose),...
-
The new diphosphanylphosphido complexes of tungsten(VI) and molybdenum(VI). Their synthesis, structures and properties
PublikacjaWe report on the reactivity of R2P–P(Li)–PR’2 (R = tBu, iPr, R’ = NEt2, iPr) towards diimido complexes [(dippN)2MCl2·dme] (M = Mo, W and dipp = 2,6-iPr2C6H3). A series of new complexes with diphosphanylphosphido ligands R2P–P–PR’2 were isolated. The solid-state structures of [(dippN)2M(Cl)(1,2-η-iPr2P–P– PiPr2)] (2Mo and 2W) and [(dippN)2M(Cl){1,2-η-tBu2P–P–P(NEt2)2}] (3Mo and 3W) were established by single-crystal X-ray diffraction...
-
Combined effect of nitrogen-doped functional groups and porosity of porous carbons on electrochemical performance of supercapacitors
PublikacjaIn this work, nitrogen-doped porous carbons obtained from chitosan, gelatine, and green algae were investigated in their role as supercapacitor electrodes. The effects of three factors on electrochemical performance have been studied— of the specific surface area, functional groups, and a porous structure. Varying nitrogen contents (from 5.46 to 10.08 wt.%) and specific surface areas (from 532 to 1095 m2g−1) were obtained by modifying...
-
Electrochemical Characterization of Gelatine Derived Ceramics
PublikacjaNew materials obtained by pyrolysis of gelatine (G) and poly(1,2-dimethylsilazane) (PSN) (weight ratio: G/PSN 70/30) at temperatures 700 and 900 °C were characterized by SEM and Raman spectroscopy. The presence of ceramics influences on the cluster size of the materials. Electrochemical tests were performed by cyclic voltammetry and galvanostatic cyclic polarization. The capacity of G/PSN was 464 and 527 mAh/g for materials pyrolysed...
-
Chestnut-Derived Activated Carbon as a Prospective Material for Energy Storage
PublikacjaIn this work, we present the preparation and characterization of biomass-derived activatedcarbon (AC) in view of its application as electrode material for electrochemical capacitors. Porouscarbons are prepared by pyrolysis of chestnut seeds and subsequent activation of the obtainedbiochar. We investigate here two activation methods, namely, physical by CO2and chemical usingKOH. Morphology, structure and specific surface area (SSA)...
-
Composite Materials Based on Polymer-Derived SiCN Ceramic and Disordered Hard Carbons as Anodes for Lithium-Ion Batteries
PublikacjaNew composite materials based on polymer-derived SiCN ceramics and hard carbons were studied in view of its application as anodes for lithium-ion batteries. Two kinds of composites were prepared by pyrolysis of the preceramic polysilazane (HTT1800, Clariant) at 1000 °C in Ar atmosphere mixed with hard carbons derived from potato starch (HC_PS) or with a hard carbon precursor, namely potato starch (PS), denoted as HTT/HC_PS and...
-
Synthesis and modification of reduced graphene oxide aerogels for biofuel cell applications
PublikacjaWe have carried out the preparation of reduced graphene oxide aerogels using eco-friendly method that is based on the Hummers method of graphite oxidation without the use of NaNO3 that produces toxic gases. To obtain a porous 3D structure of reduced graphene oxide, we performed the hydrothermal reduction at elevated temperature. We also prepared the rGO aerogel/CNT composite using multiwalled carbon nanotubes as linkers. The rGO...
-
Recovery of Anammox Biomass at Short Hydraulic Retention Time in a MBR Reactor
PublikacjaThe anammox system has been consider as an economical option for treating high concentration of nitrogen and poor in biodegradable orgaednic carbon wastewaters. This process is attractive option compared with conventional nitrogen removal because it provides a significant saving in aeration and organic addition for denitrification. The anammox technology has been applied mostly for concentrated nitrogenous wastewater containing...
-
Industrial wastewater as an external carbon source for optimization of nitrogen removal at the "Wschod" WWTP in Gdansk (Poland)
PublikacjaCarbon source alternatives for denitrification belong to the highest research area priorities as they allow to optimize N removal within the existing capacities. In particular, some food industry effluents appear to be good candidates for such alternatives due to their high C/N ratios and high content of readily biodegradable organic fraction. The aim of this study was to determine the immediate effects of dosing different types...
-
Improving denitrification efficiency at the "Wschod" WWTP in Gdansk (Poland) - effects of different carbon sources
PublikacjaCelem badań było określenie wpływu dawkowania trzech różnych źródeł węgla (ścieków po oczyszczaniu mechanicznym, metanolu, ścieków gorzelnianych) na szybkość denitryfikacji, mierzoną w warunkach laboratoryjnych z osadem czynnym z oczyszczalni ścieków Gdańsk-Wschód. Największą szybkość procesu (4.8-5.2 mgN/(g*h)) zaobserwowano dla ścieków przemysłowych. Dodatkowo przeprowadzono badanie długości fazy adaptacji osadu do metanolu w...
-
Experimental and computational analysis of SnSx encapsulated into carbonized chitosan as electrode material for potassium ion batteries
PublikacjaTin sulphide compounds (SnSx, x = 1, 2) are potential anode materials for potassium-ion batteries (PIBs) due to their characteristic layered structure, high theoretical capacity, non-toxicity and low production cost. However, they suffer from significant volume changes resulting in poor performance of such anodes. In this work incorporation of SnSx into the carbon structure was expected to overcome these disadvantages. Two SnS-based...
-
Preparation and characterization of genipin cross-linked porous chitosan–collagen–gelatin scaffolds using chitosan–CO2 solution
PublikacjaNovel porous scaffolds composed of chitosan, collagen and gelatin were prepared by the multistep procedure involving final freeze-drying and characterized. To eliminate the need for residual acid removal from the material after drying, carbon dioxide saturation process was used for chitosan blend formulation. The use of CO2 for chitosan dissolution made the scaffold preparation process more reproducible and economically sustainable....