Wyniki wyszukiwania dla: AXIAL PISTON PUMP
-
Experimental research of circular saw blade tooth axial run-out influence on cutting effects
PublikacjaW pracy przedstawiono metodę pomiaru i wyniki badań doświadczalnych wpływu bicia osiowego ostrzy piły tarczowej na efekty przecinania
-
Experimental Studies of Concrete-Filled Composite Tubes under Axial Short- and Long-Term Loads
PublikacjaThe paper presents experimental studies on axially compressed columns made of concrete-filled glass fiber reinforced polymer (GFRP) tubes. The infill concrete was C30/37 according to Eurocode 2. The investigated composite pipes were characterized by different angles of fiber winding in relation to the longitudinal axis of the element: 20, 55 and 85 degrees. Columns of two lengths, 0.4 m and 2.0 m, were studied. The internal diameter...
-
Analysis of catalitic reactors usefulness to reduce pollution generated by piston combustion engines with regard to ship main engines
PublikacjaThe article presents results which indicate that the use of catalytic reactors to reduce emissions of harmful compunds contained in the exhaust gas is important in the operation of vehicle motors operation. Efforts of the shipbuilding industry to reduce the toxicity of exhaust gas emitted by the main engines have been indicated and pointed to the desirability of the use of these catalysts in maritime transport. It has been pointed...
-
The operating field of a hydrostatic drive system. Parameters of the energy efficiency investigations of pump and hydraulic motors
PublikacjaPrzedstawiono pole pracy układu napędu hydrostatycznego. Uzasadniono podział parametrów pracy silnika hydraulicznego i pompy na parametry niezależne i zależne od pracy tych maszyn wyporowych i układu z nich utworzonego. Zaproponowano podjęcie tematu badawczego mającego na celu opracowanie metod wyznaczania charakterystyk energetycznych pomp i silników hydraulicznych obrotowych oraz zmodyfikowanych metod wyznaczania charakterystyk...
-
Selected aspects of determining the reliability of the pump subsystems with redundancy, used in main engine auxiliary systems
PublikacjaThe rules of classification societies require the use of redundancy in the systems essential for the safety of the ship. Duplication of pumps in the main engine auxiliary systems like cooling water system, lubricating oil system, fuel oil system is a good example here. Therefore, in the author's opinion, some attention should be paid to this issue. Two important questions arise here. Does duplication of pumps in marine systems...
-
Heat transfer enhancement of modular thermal energy storage unit for reversible heat pump cooperation
PublikacjaThe following article presents experimental comparison research on a hexagonal shelland-tube latent thermal energy storage (TES). Such shape of a shell was deliberately chosen instead of a cylindrical one due to its high modularity and with intent for future applications in automobiles (EV and PHEV) air conditioning systems (HVAC). Two geometries of helical coils, acting as tubes, were studied in this article. One was a simple...
-
Influence of geometry of iron poles on the cogging torque of a field control axial flux permanent magnet machine
Publikacja -
Design and Thermodynamic Analysis of a Steam Ejector Refrigeration/Heat Pump System for Naval Surface Ship Applications
Publikacja -
Comparing combined gas tubrine/steam turbine and marine low speed piston engine/steam turbine systems in naval applications
PublikacjaPorównano układy napędowe okrętowe kombinowane turbina gazowa- turbina parowa oraz spalinowy okrętowy silnik tłokowy wolnoobrotowy - turbina parowa. Porównywano moce oraz zużycie paliwa oraz parametry pary świeżej układu turbiny parowej.
-
The Influence of Permanent Magnet Length and Magnet Type on Flux-control of Axial Flux Hybrid Excited Electrical Machine
Publikacja -
Experimental and theoretical study on high-temperature creep of VT6 titanium alloy under multi-axial loading conditions
PublikacjaIn the framework of damage mechanics, we discuss a new mathematical model that describes the kinetics of the stress–strain state and damage accumulation during material degradation by the mechanism of long-term strength under complex multiaxial stress state. An experimental and theoretical technique is proposed for determination of material parameters and scalar constitutive functions for damaged media based on specially set experiments...
-
Efflux Pump Blockers in Gram-Negative Bacteria: The New Generation of Hydantoin Based-Modulators to Improve Antibiotic Activity
Publikacja -
On performance limits of switched-capacitor multi-phase charge pump circuits. Remarks on papers of Starzyk et al.
PublikacjaW pracy zweryfikowano hipotezę Starzyka nt. maksymalnego, osiągalnego wzmocnienia napięciowego w wielotaktowym konwerterze napięcia stałego typu C-przełączane (w tzw. pompie ładunkowej). W konwerterze zbudowanym z k kondensatorów maksymalne wzmocnienie określone jest przez odpowiednią potęgę liczby 2 tj. 2^(k-1) przy czym warunek podany przez Starzyka jest konieczny lecz nie jest dostateczny. Podano warunki konieczne i dostateczne...
-
Features of load and wear of main propulsion devices on sea-going ships with piston combustion engines and their impact on changes in technical states of the systems
PublikacjaThe paper presents the specificity of operation of propulsion systems of seagoing ships which causes the need to control the load on them, especially on their engines called main engines. The characteristics of the load on the propulsion systems, especially on the main engines as well as on the shaft lines and propellers driven by the engines, along with the process of wear in tribological joints (sliding tribological systems)...
-
Badania kompensacji luzów osiowych w hydraulicznych silnikach satelitowych = Researcg of axial clearances compensation in hydraulic satellite motors
PublikacjaW pracy doktorskiej przedstawiono koncepcje silnika z mechanizmem satelitowym III typu. Istotną nowością w koncepcji tego typu silnika satelitowego jest zastosowanie nowego specjalnego rozwiązania kompensacji luzów osiowych dla zmniejszania przecieków przez szczeliny czołowe mechanizmu. Ma to zapewnić ich eksploatację również z cieczami roboczymi o bardzo małych lepkościach i możliwość uzyskania małych prętkości obrotowych.
-
The Unsteady Low-Frequency Forces Acting on the Rotor Blade in the First Stage on an Axial Compressor of SO-3 Jet Engine
Publikacja -
Design and Thermodynamic Analysis of Waste Heat-Driven Zeolite–Water Continuous-Adsorption Refrigeration and Heat Pump System for Ships
Publikacja -
Temporal fine structure of all-normal dispersion fiber supercontinuum pulses caused by non-ideal pump pulse shapes
Publikacja -
Discovery of phenylselenoether-hydantoin hybrids as ABCB1 efflux pump modulating agents with cytotoxic and antiproliferative actions in resistant T-lymphoma
Publikacja -
Ekonomična efektivnist` teplovoï pompi v sistemi opalennâ = Economical efficiency of heat pump system in heating system
PublikacjaW artykule opisano wynik porównawczych obliczeń kosztów ogrzewania budynku jednorodzinnego. Porównano koszty konwencjonalnego ogrzewania z kotłem olejowym jako źródłem ciepła z kosztami ogrzewania układem hybrydowym, w którym współpracują ze sobą dwa żródła ciepła: konwencjonalny kocioł olejowy i sprężarkowa pompa ciepła. Wykonano studium parametryczne kosztów ogrzewania z wykorzystaniem metody kosztów narastających.
-
A method for evaluating the performance of a marine piston internal combustion engine used as the main engine on a ship during its voyage in different sailing conditions
PublikacjaPrzedstawiono metodę oceny działania tłokowych silników spalinowych napędu głównego staków morskich, nazywanych silnikami głównymi, działających w typowych warunkach ich eksploatacji. Warunki te zostały opisane z uwzględnieniem pola osiągów tego rodzaju silników. Metoda ta umożliwia obliczenie wartości działania w wyniku zastosowania rachunku całkowego. Znamienne jest to, że działanie wspomnianych silników spalinowych zostało przyrównane...
-
The influence of rotor-stator axial gap on the aerodynamic forces generatedin the shroud clearance of a turbine stage. Part I: Pressure field
PublikacjaPrzedstawiono wyniki badań doświadczalnych wpływu zmiany luzu osiowego na rozkład ciśnienia w uszczelnieniu nadbandażowym stopnia powietrznej turbiny modelowej. Wykazano, że w przypadku uszczelnienia promieniowego zmiana luzu osiowego nieznacznie zmienia rozkład ciśnienia w szczelinie nadbandażowej w porównaniu ze zmianą mimośrodowości czy skośnego ustawienia osi wirnika względem osi korpusu.
-
The influence of rotor-stator axial gap on the aerodynamic forces generatedin the shroud clearance of a turbine stage. Part II: Forces and moments
PublikacjaPrzedstawiono wyniki badań doświadczalnych wpływu zmiany luzu osiowego na wymuszenia aerodynamiczne powstające w uszczelnieniu nadbandażowym stopnia powietrznej turbiny modelowej. Wykazano, że w przypadku uszczelnienia promieniowego zmiana luzu osiowego odgrywa niewielką rolę w generowaniu sił i momentów aerodynamicznych w szczelinie nadbandażowej w porównaniu ze zmianą mimośrodowości czy skośnego ustawienia osi wirnika względem...
-
Calculation Program Supporting Switched Capacitor DC-DC Charge Pump Design (CP Design Calculator) - PartII: User's Guide
PublikacjaPrzewodnik użytkownika programu wspomagającego projektowanie pomp ładunkowych z przełączanymi pojemnościami. Praca jest podzielona na 3 rozdziały (INTRODUCTI ON, GRAPHICAL USER INTERFACE (GUI), PROGRAM NOTIFICATIONS) i podziękowania.
-
Example of Using Particle Swarm Optimization Algorithm with Nelder–Mead Method for Flow Improvement in Axial Last Stage of Gas–Steam Turbine
Publikacja -
Calculation Program Supporting Switched Capacitor DC-DC Charge Pump Design (CP Design Calculator) - Part III: Illustrative Examples
PublikacjaW pracy przedstawiono szereg przykładów użycia programu do obliczeń wspomagających projektowanie pompy ładunkowej, w tym syntezę układu kanonicznego i wyznaczanie wszystkich teoretycznie realizowalnych współczynników przetwarzania (wzmocnień napięciowych), rezystancję wyjściową zastępczą w różnych trybach pracy, sprawność energetyczną, wrażliwość na pojemności pasożytnicze, warunki początkowe w okresowym stanie ustalonym - do współpracy...
-
Michał Wasilczuk prof. dr hab. inż.
OsobyMichał Wasilczuk, absolwent Wydziału Budowy Maszyn Politechniki Gdańskiej (1986), a obecnie profesor zwyczajny na Wydziale Mechanicznym PG i kierownik Katedry Konstrukcji Maszyn i Pojazdów od początku swojej działalności naukowej zajmuje się hydrodynamicznymi łożyskami wzdłużnymi oraz, szerzej inżynierią łożyskowania, w ramach zespołu naukowego stworzonego przez doc. Olgierda Olszewskiego. Od kilkunastu lat zespół specjalizuje...
-
The Quality of Life and Satisfaction with Continuous Glucose Monitoring Therapy in Children under 7 Years of Age with T1D Using the rtCGM System Integrated with Insulin Pump—A Caregivers Point of View
Publikacja -
Displacement control in PWK-type pumps
PublikacjaThe most important, strategic goal however is creation of the variable displacement version of the new pump PWK. Thanks to full discharge of it's commutation mechanism from hydrostatic forces the variable pump can be directly controlled by low-energy actuator like proportional electromagnet or stepping motor. It means that costly and complicated hydraulic servomechanism (applied in all present variable displacement pumps) is no...
-
Validation of lumbar spine finite element model
Dane BadawczeThe functional biomechanics of the lumbar spine have been better understood by finite element method (FEM) simulations. However, there are still areas where the behavior of soft tissues can be better modeled or described in a different way. The purpose of this research is to develop and validate a lumbar spine section intended for biomechanical research....
-
Compact satellite hydraulic unit
PublikacjaThe article describes the design and operation of a prototype hydraulic unit. It is based on an inversed kinematics, satellite pump in which the body rotates around the shaft. The pump is placed inside the electric motor. Thanks to that the compact and low mass construction was achieved. Thanks to new commutation unit with enlarged channels, lower pressure losses were obtained. The article presents the construction and results...
-
Influence of the low ambient temperature on the start-up process of hydraulic pumps
PublikacjaStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of pressure drop in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump working chambers with...
-
Possibility to use engine compression ignition engines in floating power plants marine
PublikacjaCompression-ignition engines used in ship technology as main propulsion engines are large units reaching even to 50-60 MW. The engines can be used in power industry for electricity generation in a simple or combined steam turbine system in combined heat and power plants. The leading engine in such an arrangement is an internal-combustion piston engine. The main propulsion engines are used in large piston internal-combustion engines...
-
Water-lubricated stern tube bearing - experimental and theoretical investigations of thermal effects
PublikacjaThe paper presents research results of thermal phenomena accompanying operation of a water-lubricated stern tube bearing with axial grooves. Experimental tests revealed, that intensity of forced axial flow has strong influence on bush temperature. Numerical simulations focused on investigation of the thermal phenomena under operation of water-lubricated journal bearing showed, that restricted axial flow promotes backflow of the...
-
Influence of lubricating oil improvers on performance of crankshaft seals
PublikacjaThis paper presents an original method for checking influence of lubricating oil improvers on performance of crankshaft seals of combustion piston engine. Crankshaft seals were tested with the use of a modified friction node of T-02 four- ball apparatus in laboratory conditions. The tests were conducted according to a worked-out algorithm. Their results confirmed usefulness of the method for determining „harmful” performance...
-
New generation of the satellite hydraulic pumps
PublikacjaHydraulic satellite machines are known and produced in many versions, recognizable by the number of humps on their inner rotor and external gear, and therefore by the number of cooperating gears (satellites). All known shapes were however designed on the base of preliminary assumption that rotor’s and external gear’s pitch lines are formed by merging arcs, tangent to each other in the. This assumption makes calculations easier,...
-
DESIGN OF THE DUAL CONSTELLATION GPS/GALILEO MOBILE DEVICE FOR IMPROVING NAVIGATION OF THE VISUALLY IMPAIRED IN AN URBAN AREA, POLISH MARITIME RESEARCH
PublikacjaThe article discusses damages of essential tribological associations in crankshaft and piston systems of large power two-stroke engines used as main engines, which take place during transport tasks performed by those ships. Difficulties are named which make preventing those damages impossible, despite the fact that the technical state of engines of this type is identified with the aid of complex diagnostic systems making use of...
-
In Situ Verification of Numerical Model of Water Hammer in Slurries
PublikacjaThis paper presents a numerical model of transient flow in a pressure slurry pipeline network with verification based on in situ measurements. The model, primarily verified in laboratory conditions, has been extended and applied to the case of a large and complex slurry pipeline network in Poland. In the model, the equivalent density concept was applied. In situ experiments were performed for various unsteady flow episodes, caused by...
-
PROBABILISTYCZNE ASPEKTY ZUŻYCIA SKOJARZEŃ CIERNYCH UKŁADÓW KORBOWO-TŁOKOWYCH NA PRZYKŁADZIE OKRĘTOWYCH SILNIKÓW SPALINOWYCH DWUSUWOWYCH NAPĘDU GŁÓWNEGO
PublikacjaW artykule przestawiono propozycję rozpatrywania zarówno obciążenia jak i zużywania ślizgowych skojarzeń ciernych (łożysk głównych i korbowych) układów korbowo-tłokowych silników spalinowych, zwłaszcza głównych, a także skojarzeń „tłok-tuleja” tych silników, jako procesów stochastycznych. Propozycję tę uzasadniono tym, że deterministyczne podejście do badania zarówno obciążenia jak i zużycia wspomnianych skojarzeń uniemożliwia...
-
New satellite pumps
PublikacjaStosowanie Maszyn company from Katowice was initiator and originator of newest original high pressure satellite pumps series of types PSM. Construction solution, research and development of these pumps have been conducted by Team of Hydraulics and Pneumatics of Gdansk University of Technology in cooperation with this company within the confines of research project nr R0300103 (source of funds: Ministry of Science and Higher Education)....
-
Porównanie mocy strat energetycznych w pompie wyporowej o zmiennej wydajności określonych bez uwzględnienia bądź z uwzględnieniem mocy ściskania oleju hydraulicznego
PublikacjaPorównano moce strat energetycznych w pompie wyporowej o zmiennej wydajności, określone bez uwzględnienia bądź z uwzględnieniem mocy ściskania oleju hydraulicznego. Ocena mocy ściskania cieczy w pompie stała się możliwa dzięki zastosowaniu, zaproponowanej przez autora, metody określenia stopnia zapowietrzenia cieczy w pompie. W metodzie określenia stopnia zapowietrzenia cieczy w pompie oraz w ocenie mocy strat objętościowych ściskania...
-
Satelitowy agregat pompowy
PublikacjaW artykule opisano najnowszą konstrukcję satelitowego agregatu pompowego charakteryzującego się tym, że pompa satelitowa jest umieszczona wewnątrz silnika elektrycznego i zasysa ciecz poprzez otwór wydrążony osiowo w wale silnika. Zastosowana w agregacie pompa satelitowa jest nowatorską konstrukcją zawierającą mechanizm satelitowy o odwróconej kinematyce znamienny tym, że planeta (wirnik) oraz płyty kompensacyjne (rozrządu) są...
-
Fatigue fracture surface metrology of thin-walled tubular austenitic steel specimens after asynchronous loadings
PublikacjaThis paper aims to study the effect of asynchronous axial-torsional strain-controlled loading histories on fracture surface behavior of thin-walled tubular X5CrNi18-10 (304/304L) austenitic steel specimens. Tests under pure axial loading and pure torsional loading are also conducted to better segregate the effect of multiaxiality. The fractures surface topographies were examined through the profiles over the entire surface with...
-
ASSESSMENT OF ENGINE OPERATION WITH THE USE OF AN OPERATION INDICATOR BASED ON TEST BENCH RESULTS OF A ROBINSUBARU EX17 ENGINE
PublikacjaPaper presents results of an experimental verification of the method of quantitative evaluation of engine operation, presented in the literature, exemplified by a low-power internal combustion piston engine. In accordance with such interpretation, engine operation may be presented as a physical quantity defined as operation indicator. The paper presents results of preliminary tests, processed in that aspect, carried out on an engine...
-
Low-cost 3D Printed Circularly Polarized Lens Antenna for 5.9 GHz V2X Applications
PublikacjaThis paper presents design and realization of a circularly polarized antenna consisting of a linearly polarized patch antenna and a 3D printed lens, at the same time performing the functions of wave collimator and a polarizer. The antenna is dedicated for 802.11p systems, as a part of road infrastructure, with operation bandwidth 5.85 - 5.925 GHz. Its realised gain and axial ratio at center frequency 5.9 GHz are 14.3 dBi and 2.17...
-
Model matematyczny strat objętościowych ściskania oleju hydraulicznego w pompie wyporowej o zmiennej wydajności
PublikacjaCelem pracy było stworzenie możliwości oceny strat objętościowych wynikających ze ściskania oleju hydraulicznego w komorach roboczych wysokociśnieniowej pompy wyporowej o zmiennej wydajności na obrót wału. Straty objętościowe ściskania oleju muszą być określone jako funkcje tych samych parametrów, w zależności od których ocenione są straty objętościowe przecieków oleju w komorach, wynikające z jakości rozwiązania konstrukcyjnego...
-
Experimental ORC micro-power plant for CHP application Part A: power plant arrangement
PublikacjaThe co-generative micro-power plant with the HFE7100 applied as a working medium was designed and built for experimental investigations. The heat output of the plant was assumed equal to 20 kW, while the electric output amounted to about 3kW. Examples of the results of the preliminary experimental research on a boiler, heat exchangers, a pump and a turbine-generator set are presented and analysed.
-
Studies on the influence of technological variants of finishing machining on flow of parts in flexible manufacturing
PublikacjaIn the article below the problems of influence of variants of finishing processing on flow of machining parts in flexible manufacturing system were presented. The investigations were carried out the technological processes for piston rods and rams of hydraulic cylinders. There were also presented model variants of technological processes for piston rods finished with the burnishing. In these studies the influence of technological...
-
Selection of drive engines for dredge pumps
PublikacjaThis paper presents the principles of selecting drive engines for dredge pumps, formulated by this author. In order to formulate them influence of drive engines on dredge pump characteristics and dredger effectiveness, have been analyzed. Also, an analysis of results of the author's operational investigations concerning energy consumption and parameters of excavated soil transport on board dredgers has been performed.
-
Design and optimization of a novel compact broadband linearly/circularly polarized wide-slot antenna for WLAN and Wi-MAX applications
PublikacjaA novel topologically modified structure of a compact low profile wide-slot antenna for broadband applications is presented. The antenna comprises a modified E-shaped slot with unequal arm lengths in the ground plane, and a parasitic quasi-rectangular loop placed coplanar with the feedline. For exciting orthogonal modes with equal amplitude, a single-point feeding technique with an asymmetrical geometry of the coplanar waveguide...