Wyniki wyszukiwania dla: LIGHT PROPAGATION
-
Testing the Wide-Sense Stationarity of Bandpass Signals for Underwater Acoustic Communications
PublikacjaThe Underwater Acoustic Communication (UAC) systems work in communication channels characterized by a large variety of multipath propagation conditions that can additionally change over time. Designing a reliable communication system requires knowledge of the transmission parameters of the channel. There is a need for the development of adaptive signaling schemes that would dynamically optimize the signal parameters of the physical...
-
Properties and Formation of Mineralized Veins in an Organic-Rich Shale Formation
PublikacjaAn earlier paper defined mineral and organic matter constituents in weak interfaces in shale formations (Ptaszynska, et. al., 2016). The formation studied in the earlier work and here is the Jurassic, early-Cretaceous Vaca Muerta formation in the Neuquen basin in Argentina. In this earlier work, mineralized "veins" were noted to be prevalent and complicated, sometimes being shear weak interfaces while in other cases they were not....
-
MATCHED FILTER APPROACH FOR MICROSEISMIC SIGNAL PROCESSING OF REAL DATA FROM EAST POMERANIA SHALE GAS
PublikacjaThe microseismic monitoring is a method of monitoring of fracture propagation during hydraulic fracturing (HF)process. An array of several hundred geophones is placed on the surface to record little ground tremors induced by fracturing process. Filtration and summation of signals from geophones is essential to identify and locate fracturing events from underground. Authors propose a method of matched filtering, that is usually...
-
Guided ultrasonic waves for detection of debonding in bars partially embedded in grout
PublikacjaThis paper deals with theoretical, numerical and experimental investigations of guided wave propagation in multilayered cylindrical bars with pre-existing debonding. The research focuses on a complex description of the nature of the wave phenomena occurring in a debonded specimen with a special emphasis on the influence of the location of damage on the wave conversion and diffraction. Experimental non-destructive and destructive...
-
Investigation of the vertical distribution of the sound speed of the Gulf of Gdansk in the years 2000-2010
PublikacjaThe conditions of the acoustic wave propagation in the southern Baltic are much more complex than in other shallow waters. In the typical shallow water, seasonal changes in acoustical conditions in the upper layer, of the depth of about 60-70 m, are observed. They are caused by variation of the annual meteorological conditions. Most often, in the deep water layer, acoustical conditions are stable throughout the year. However, in...
-
Limitations of WSSUS modeling of stationary underwater acoustic communication channel
PublikacjaPerformances of underwater acoustic communication (UAC) systems are strongly related to specific propagation conditions of the underwater channel. Due to their large variability, there is a need for adaptive matching of the UAC systems signaling to the transmission properties of the channel. This requires a knowledge of instantaneous channel characteristics, in terms of the specific parameters of stochastic models. The wide-sense...
-
Mitigating Time-Constrained Stolen-Credentials Content Poisoning in an NDN Setting
PublikacjaNDN is a content-centric networking architecture using globally addressable information objects, created by publishers and cached by network nodes to be later accessed by subscribers. Content poisoning attacks consist in the substi-tution by an intruder publisher of bogus objects for genuine ones created by an honest publisher. With valid credentials stolen from an honest publisher, such attacks seem unstoppa-ble unless object...
-
Debonding Detection in Reinforced Concrete Beams with the Use of Guided Wave Propagation
PublikacjaOne of the most frequent damage of the reinforced concrete structures is debonding between steel bar and concrete cover. In the case of debonding occurrence not only the strength of the structure decreases, but also it is more vulnerable to corrosion damages. For this reason fast and effective methods of debonding detection in an early stage of its development need a significant boost. The paper presents analytical and experimental...
-
FDTD Method for Electromagnetic Simulations in Media Described by Time-Fractional Constitutive Relations
PublikacjaIn this paper, the finite-difference time-domain (FDTD) method is derived for electromagnetic simulations in media described by the time-fractional (TF) constitutive relations. TF Maxwell’s equations are derived based on these constitutive relations and the Grünwald–Letnikov definition of a fractional derivative. Then the FDTD algorithm, which includes memory effects and energy dissipation of the considered media, is introduced....
-
Novel Cast Polyurethanes Obtained by Using Reactive Phosphorus-Containing Polyol: Synthesis, Thermal Analysis and Combustion Behaviors
PublikacjaPhosphorus-containing polyol applications in polyurethane synthesis can prevent volatilization of flame retardants and their migration on the surface of a material. In this work, novel cast polyurethanes were prepared by a one-step method with the use of different amounts of phosphorus-containing polyol, 4,4′–diphenylmethane diisocyanate and 1,4-butanediol. The chemical structure, thermal, physicochemical and mechanical properties...
-
Study of probe signal bandwidth influence on estimation of coherence bandwidth for underwater acoustic communication channel
PublikacjaA signal transmitted in a shallow Underwater Acoustic Communication (UAC) channel suffers from time dispersion due to the multipath propagation and the refraction phenomena. This causes intersymbol interference of the received signal and frequency-selective fading observed in its spectrum. Coherence bandwidth is one of the key transmission parameters used for designing the physical layer of a data transmission system to minimise...
-
LOS and NLOS identification in real indoor environment using deep learning approach
PublikacjaVisibility conditions between antennas, i.e. Line-of-Sight (LOS) and Non-Line-of-Sight (NLOS) can be crucial in the context of indoor localization, for which detecting the NLOS condition and further correcting constant position estimation errors or allocating resources can reduce the negative influence of multipath propagation on wireless communication and positioning. In this paper a deep learning (DL) model to classify LOS/NLOS...
-
Propagation of initially sawtooth periodic and impulsive signals in a quasi-isentropic magnetic gas
PublikacjaThe characteristics of propagation of sawtooth periodic and impulsive signals at a transducer are analytically studied in this work. A plasma under consideration is motionless and uniform at equilibrium, and its perturbations are described by a system of ideal magnetohydrodynamic equations. Some generic heating/cooling function, which in turn depends on equilibrium thermodynamic parameters, may destroy adiabaticity of a flow and...
-
Magnetoacoustic heating in a quasi-isentropic magnetic gas
PublikacjaThe nonlinear heating of a plasma which associates with the transfer of energy of magnetoacoustic waves into that of the entropy mode, is analytically studied. A plasma is uniform and motionless at equilibrium. Perturbations in a plasma are described by a system of ideal magnetohydrodynamic equations. The equilibrium straight magnetic strength and the wave vector form a constant angle which varies from 0 to π/2. There exist four...
-
Damage Imaging in Lamb Wave-Based Inspection of Adhesive Joints
PublikacjaAdhesive bonding has become increasingly important in many industries. Non-destructive inspection of adhesive joints is essential for the condition assessment and maintenance of a structure containing such joints. The aim of this paper was the experimental investigation of the damage identification of a single lap adhesive joint of metal plate-like structures. Nine joints with different defects in the form of partial debonding...
-
An intelligent cellular automaton scheme for modelling forest fires
PublikacjaForest fires have devastating consequences for the environment, the economy and human lives. Understanding their dynamics is therefore crucial for planning the resources allocated to combat them effectively. In a world where the incidence of such phenomena is increasing every year, the demand for efficient and accurate computational models is becoming increasingly necessary. In this study, we perform a revision of an initial proposal...
-
Multitaper-Based Post-processing of Compact Antenna Responses Obtained in Non-anechoic Conditions
PublikacjaThe process of developing antenna structures typically involves prototype measurements. While accurate validation of far-field performance can be performed in dedicated facilities like anechoic chambers, high cost of construction and maintenance might not justify their use for teaching, or low-budget research scenarios. Non-anechoic experiments provide a cost-effective alternative, however the performance metrics obtained in such...
-
EVALUATION OF THE USE OF M2M-TYPE NB-IoT AND LTE TECHNOLOGIES FOR MARITIME COMMUNICATION SYSTEMS
PublikacjaThe development of IoT (the Internet of Things) wireless transmission opens a new era in communication systems. In the next years, the development and implementation of IoT systems will be very dynamic. It can be seen that the solutions of LTE – NB-IoT (Long Term Evolution – Narrowband IoT) transmission devices are implemented in a wide range of terrestrial solutions, e.g. smart grids. This paper aims to analyse the possibility...
-
Designate of CTOD for WM and HAZ, report no: WOiO/II/122/2014
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...
-
Designate CTOD Heat Affected Zone of butt weld, Report No: WOiO/II/76/2013
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
Designate CTOD of Weld Metal of butt weld, No WOiO/II/108/2013
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
Crack propoagation in MgO-PSZ ceramic materials
PublikacjaThe properties of ceramic materials such as elevated hardness, high temperature capability, low coefficient of thermal expansion are of interest for rolling element materials. Widely used ceramic materials in engineering applications are silicon nitride, zirconia and alumina. The paper presents an experimental study of the fatigue life of MgO-PSZ ceramic material in lubricated contact with defined types of cracks. A ceramic angular...
-
CTOD designation for WM and HAZ in butt joint made from S460 ML steel, Expertise No. WOiO/II/82/2015
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...
-
Characteristics of the Polarised Off-Body Channel in Indoor Environments
PublikacjaThis paper addresses the depolarisation effect in off-body Body Area Networks channels, based on measurements performed at 2.45 GHz in an indoor environment. Seven different scenarios, involving both static and dynamic users, were considered, taking a statistical perspective. The analysis of the cross-polarisation discrimination is performed, as well as the analysis of path loss in co- and cross-polarised channels. Results show...
-
Wave Method for Structural Health Monitoring: Testing Using Full-Scale Shake Table Experiment Data
PublikacjaAn algorithm of the wave method for structural health monitoring (SHM) is tested and calibrated using shake table experiment data of a full-scale, seven-story, reinforced-concrete building slice. The method is based on monitoring changes in the velocity of waves propagating vertically through the structure, identified by least-squares (LSQ) fit of beam models. The experiment was conducted by a team from the University of California,...
-
Characteristics of the polarised off-body channel in indoor environments
PublikacjaThis paper addresses the depolarisation effect in off-body body area networks channels, based on measurements performed at 2.45 GHz in an indoor environment. Seven different scenarios, involving both static and dynamic users, were considered, taking a statistical perspective. The analysis of the cross-polarisation discrimination is performed, as well as the analysis of path loss in co- and cross-polarised channels. Results show...
-
MICROSEISMIC EVENT DETECTION USING DIFFERENT ALGORITHMS ON REAL DATA FROM PATCH ARRAY GEOPHONE GRID FROM EASTERN POMERANIA FRACTURING JOB
PublikacjaThe microseismic monitoring is a method of monitoring of fracture propagation during hydraulic fracturing process. Hydraulic fracturing is a method of reservoir stimulation used especially for unconventional gas recovery. A matrix of several thousand geophones is placed on the surface of earth to record every little tremor of ground induced by fracturing process. Afterwards, the signal is analysed and the place of tremor occurrence...
-
Vehicular Communication Environments
PublikacjaCommunication to and between road vehicles (cars, truck, buses, trains, etc.) are of growing interest. This is partly due to the attractive services that cooperative intelligent transport systems (C-ITSs) provides, mainly in the areas of traffic safety and traffic efficiency. An enabler for C-ITS is wireless vehicle-to-vehicle (V2V) and vehicle-to-infrastructure (V2I) communication, collectively referred to as vehicle-to-X (V2X)...
-
Consequences of lysine auxotrophy for Candida albicans adherence and biofilm formation
PublikacjaA number of factors are known to be involved in Candida albicans virulence, although biofilm development on the surfaces of indwelling medical devices is considered to promote superficial or systemic disease. Based on previously reported up-regulation of saccharopine and acetyllysine in biofilm cells and activation of the lysine biosynthesis/degradation pathway, we investigated...
-
Evaluation of the resistance of steel–concrete adhesive connection in reinforced concrete beams using guided wave propagation
PublikacjaThe development of the nondestructive diagnostic methods is of significant importance in the last decades. A special attention is paid to diagnostics of reinforced concrete structures, which are very popular in the civil engineering field. A possible use of the guided waves in the estimation of the resistance of steel–concrete adhesive connection is studied in the following paper. The relationships relating adhesive connection...
-
Deep Learning-Based Intrusion System for Vehicular Ad Hoc Networks
PublikacjaThe increasing use of the Internet with vehicles has made travel more convenient. However, hackers can attack intelligent vehicles through various technical loopholes, resulting in a range of security issues. Due to these security issues, the safety protection technology of the in-vehicle system has become a focus of research. Using the advanced autoencoder network and recurrent neural network in deep learning, we investigated...
-
A Wideband Channel Model for Body Area Networks in Circular Metallic Indoor Environments
PublikacjaIn this paper, the wideband characterization of the propagation channel in circular metallic indoor environments is addressed, regarding Body Area Networks and 5G small cells, an analytical model for the dependence of the mean delay and the average delay spread on the circle radius, the working frequency and the distance between the transmitter and the receiver being proposed. The derivation of the model is initially done analytically,...
-
Simulations of hydro-fracking in rock mass at meso-scale using fully coupled DEM/CFD approach
PublikacjaThe paper deals with two-dimensional (2D) numerical modelling of hydro-fracking (hydraulic fracturing) in rocks at the meso-scale. A numerical model was developed to characterize the properties of fluid-driven fractures in rocks by combining the discrete element method (DEM) with computational fluid dynamics (CFD). The mechanical behaviour of the rock matrix was simulated with DEM and the behaviour of the fracturing fluid flow...
-
Fatigue Bending of V-Notched Cold-Sprayed FeCoCrNiMn Coatings
PublikacjaCold-spray coatings were produced by FeCoCrNiMn high-entropy alloy powders deposited on carbon steel substrate. The coatings were realized at intermediate temperature and high pressure (at 1100 °C and 7 MPa). The coating microstructure was characterized by scanning electron microscopy and X-ray diffraction, revealing a very dense deposition and high flattening ratio of the splatted particles. This had a large influence on the...
-
A new model of fuel spray shape at early stage of injection in a marine Diesel engine
PublikacjaIn the cylinders of a marine diesel engine, self-ignition occurs in very shortly time after the fuel injection into the combustion chamber. Therefore, the paper present was to develop a model of diesel fuel spray for the early stage of fuel spray for in marine diesel engine. There were taken into consideration the main aspects technical such as nozzle diameter of marine engine injector and backpressure in combustion chamber. In...
-
Analysis of Impulse Responses Measured in Motion in a Towing Tank
PublikacjaThe growing interest in developing autonomous underwater vehicles (AUVs) and creating underwater sensor networks (USNs) has led to a need for communication tools in underwater environments. For obvious reasons, wireless means of communication are the most desirable. However, conducting research in real conditions is troublesome and costly. Moreover, as hydroacoustic propagation conditions change very significantly, even during...
-
On the crack front curvature in bonded joints
PublikacjaStandard tests of adhesively bonded specimens are likely to produce heterogeneous stress distribution along the crack front and its vicinity. High separation rate mode I dominated fracture test is performed.Observation of post mortem fractured surfaces with an optical microscope reveals characteristic features of mixed mode I/III fracture near the sides of the specimen but not in the middle. At first, finite elements calculations...
-
Earthquake-Induced Structural Pounding
PublikacjaEarthquake-induced structural pounding between insufficiently separated build-ings, or bridge segments, has been repeatedly observed during ground motions. The reports after earthquakes indicate that it may lead to some local damage in the case of moderate seismic events or may result in considerable destruction or even collapse of colliding structures during severe ground motions. Pounding in build-ings is usually caused by the...
-
Sound intensity distribution around organ pipe
PublikacjaThe aim of the paper was to compare acoustic field around the open and stopped organ pipes. The wooden organ pipe was located in the anechoic chamber and activated with a constant air flow, produced by an external air-compressor. Thus, long-term steady state response was possible to obtain. Multichannel acoustic vector sensor was used to measure the sound intensity distribution of radiated acoustic energy. Measurements have been...
-
Planar Microwave Bragg Reflector Resonant Dielectric Sensor
PublikacjaIn this paper, a periodic structure is used to design a microwave Bragg reflector with the help of hexagonal lattice, which provides a 5 GHz wide stopband between the low-pass band with cut-off frequency 2.6 GHz and the bandpass response with start and stop frequency 7.8 GHz and 10.5 GHz, respectively. A defect in lattice allows passing a narrowband signal at 6 GHz which is found, from the dispersion relation, to be in the region...
-
The In-Depth Studies of Pulsed UV Laser-Modified TiO2 Nanotubes: The Influence of Geometry, Crystallinity, and Processing Parameters
PublikacjaThe laser processing of the titania nanotubes has been investigated in terms of morphology, structure, and optical properties of the obtained material. The length of the nanotubes and crystallinity, as well as the atmosphere of the laser treatment, were taken into account. The degree of changes of the initial geometry of nanotubes were checked by means of scanning electron microscopy, which visualizes both the surface and the cross-section....
-
Detection and Imaging of Debonding in Adhesive Joints of Concrete Beams Strengthened with Steel Plates Using Guided Waves and Weighted Root Mean Square
PublikacjaStrengthening of engineering structures is an important issue, especially for elements subjected to variable loads. In the case of concrete beams or slabs, one of the most popular approaches assumes mounting an external reinforcement in the form of steel or composite elements by structural adhesives. A significant disadvantage of adhesive joints is the lack of access to the adhesive film for visual condition assessment, thus, there...
-
Smart acoustic band structures
PublikacjaSmart acoustic band structures exhibit very interesting and non-standard physical properties due to the periodic nature of their certain characteristic on different scale levels. They manifest mostly in their frequency spectra as socalled frequency band-gaps or stop-bands, what has a great impact on the behaviour of these structures in relation to the propagation of vibro-acoustic signals that can be transmitted through the structures...
-
Fracture surface formation of notched 2017A-T4 aluminium alloy under bending fatigue
PublikacjaThe effect of cyclic loading on facture surface topology in notched components made by aluminium alloys is not completely clear. Fractogra-phy and fracture mechanics can help to understand this interdependency. This paper aims to study the distribution of the fracture surface roughness of notched 2017A-T4 aluminium alloy after bending fatigue using an optical focus-variation surface measurement technique by applying the fracture...
-
Propagation Characteristics of Partial Discharges in an Oil-Filled Power Transformer
PublikacjaPower transformers are among the most important assets in the power transmission and distribution grid. However, they suffer from degradation and possible faults causing major electrical and financial losses. Partial discharges (PDs) are used to identify the insulation health status and their degradation level. PDs are incipient, low-magnitude faults caused by localized dielectric breakdown. Those activities emit signals in many...
-
Fracture Areas Quantitative Investigating of Bending-Torsion Fatigued Low-Alloy High-Strength Steel
PublikacjaIn this study, the impact of pseudo-random non-proportional bending-torsion fatigue loadings proportion on the fatigue life and the fracture surface topography was analyzed. Investigation was carried out for 24 specimens made of S355J2 steel with 11 different ratios of maximum stresses λ. For these cases, after the fatigue tests, the surface topography measurements were carried out using an optical profilometer, using the focus...
-
Perfect thermal contact of hyperbolic conduction semispaces with an interfacial heat source
PublikacjaThe problem of thermal contact between two bodies with a heat source at their interface presents great scientific and practical interest. On the time scale of a nanosecond or shorter, heat propagation should be considered in the form of thermal waves of finite speeds. This study investigated the thermal behaviour of hyperbolic conduction semispaces in perfect thermal contact subjected to the action of an interfacial heat source....
-
Analysis of Impulse Responses Measured in Motion in a Towing Tank
PublikacjaThe growing interest in developing autonomous underwater vehicles (AUVs) and creating underwater sensor networks (USNs) has led to a need for communication tools in underwater environments. For obvious reasons, wireless means of communication are the most desirable. However, conducting research in real conditions is troublesome and costly. Moreover, as hydroacoustic propagation conditions change very significantly, even during...
-
Accounting for the distributions of input quantities in the procedure for the measurement uncertainty evaluation when calibrating the goniometer
PublikacjaThe discords concerning the measurement uncertainty evaluation in the Guide to the Expressing of Uncertainty in Measurement (GUM) and its Supplement 1 are considered. To overcome these discords, the authors of the paper propose to use the kurtosis method and the law of the propagation of the expanded uncertainty. Using the example of the goniometer calibration, the features of accounting for the distribution laws of input quantities...
-
Free-standing TiO2 nanotubes decorated with spherical nickel nanoparticles as a cost-efficient electrocatalyst for oxygen evolution reaction
PublikacjaHere, we report significant activity towards the oxygen evolution reaction (OER) of spherical nickel nanoparticles (NPs) electrodeposited onto free-standing TiO2 nanotubes (TNT) via cyclic voltammetry. It has been shown that simple manipulation of processing parameters, including scan rate and number of cycles, allows for formation of the NPs in various diameters and amounts. The polarization data with respect to transmission electron...