Wyszukiwarka
Wyniki wyszukiwania dla: RENEWABLE ENERGY SOURCES (RES)
-
Exergy analysis of the Szewalski cycle with a waste heat recovery system
PublikacjaThe conversion of a waste heat energy to electricity is now becoming one of the key points to improve the energy efficiency in a process engineering. However, large losses of a low-temperature thermal energy are also present in power engineering. One of such sources of waste heat in power plants are exhaust gases at the outlet of boilers. Through usage of a waste heat regeneration system it is possible to attain a heat rate of approximately...
-
Three-dimensional CFD modeling of a steam ejector
Publikacja -
The Influence of LED Lighting Sources on the Nature of Power Factor
PublikacjaThis article presents measurements of electric power absorbed by a newly built facility for office and scientific research activities. These measurements highlighted the need for compensation of capacitive reactive power—not predicted by the designer—due to the vast use of LED lighting in the facility. The article also describes a reactive power compensation system, designed on the basis of the above-mentioned measurements, and...
-
The Course and the Effects of Agricultural Biomass Pyrolysis in the Production of High-Calorific Biochar
PublikacjaThe thermal pyrolysis of agriculture biomass has been studied in a fixed-bed reactor, wherethe pyrolysis was conducted at a steady temperature of 800◦C. This work analyses the pyrolysisproducts of six agricultural wastes: pistachio husks, walnut husks, sunflower hulls, buckwheat husks,corncobs and coconut shells. The conducted research compared examples of large waste biomassstreams from different parts of the world as a potential...
-
Nature-Inspired Driven Deep-AI Algorithms for Wind Speed Prediction
PublikacjaPredicting wind energy production accurately is crucial for enhancing grid management and dispatching capacity. However, the inherent unpredictability of wind speed poses significant challenges to achieving high prediction accuracy. To address this challenge, this study introduces a novel pre-processing framework that leverages thirteen nature-inspired optimization algorithms to extract and combine Intrinsic Mode Functions (IMFs)...
-
g-C3N4 for Photocatalytic Degradation of Parabens: Precursors Influence, the Radiation Source and Simultaneous Ozonation Evaluation
PublikacjaGraphitic carbon nitride (g-C3N4) is a promising catalyst for contaminants of emerging concern removal applications, especially as a visible-light-driven material. In this study, g-C3N4 catalysts were effectively synthesized through a simple thermal polymerization method, using melamine, urea, and thiourea as precursors to elucidate the influence of these compounds on the final product’s photocatalytic performance. The degradation...
-
Quality Testing of Welded Joints of Wind Towers with Advanced Ultrasonic Techniques – a Case Study
PublikacjaThe application of advanced quality control tests for welds is essential for enhancing competitiveness in thewelded construction industry. The global focus on obtaining energy from alternative sources is leading to the increased production of wind towers. Improving the method of conducting inspections is necessary as wind tower structuresare subject to 100% quality control of welded joints. The article presents the comparison of...
-
Bio‐polyols synthesized by liquefaction of cellulose: Influence of liquefaction solvent molecular weight
PublikacjaCurrently, the plastics industry including polyurethanes is based on the use of petrochemicals. For this reason, scientists are looking for new types of renewable resources for the substitution of petrochemical substances. This work aims to evaluate the effect of polyethylene glycols (PEG) with different molecular mass impact on properties of bio-based polyols synthesized via biomass liquefaction of cellulose. To date, research...
-
The voltage on bus bars of the main switchboard of the ro-ro ship electrical power system during a sea voyage
Dane BadawczeThe dataset is part of the research results on the quality of supply voltage on bus bars of the main switchboard of the ship's electrical power system in different states of ship exploitation. The attached dataset contains the measurement results carried out onboard a ro-ro ship during a sea voyage.
-
The voltage on bus bars of the main switchboard of the ro-ro ship electrical power system during maneuvering
Dane BadawczeThe dataset is part of the research results on the quality of supply voltage on bus bars of the main switchboard of the ship's electrical power system in different states of ship exploitation. The attached dataset contains the measurement results carried out onboard a ro-ro ship during maneuvering.
-
COMBINING FUNCTIONAL AND AESTHETIC ASPECTS OF DAYLIGHTING IN SUSTAINABLE ARCHITECTURE WITH THE USE OF DIGITAL DESIGN METHODS
PublikacjaThe aesthetics of modern architecture should relate to its origins and goals - the environment, function, sustainability and its users. One of the conditions that meet the criteria is the presence of daylight and the use of its potential. The contemporary digital tools that support the design process allow to controlling the use of difficult and capricious materials, such as daylight. They also combine daylighting aspects with...
-
Performance of microbial fuel cells operated under anoxic conditions
PublikacjaNowadays, microbial fuel cells (MFC) stand up as a promising renewable energy source. Due to the ability of the MFC to oxidize a wide spectrum of substrates, wastewater seems to be one of the most interesting fuels. Unfortunately, wastewater could contain electron acceptors such as nitrate, which could interfere with the electrical performance of the MFC. In this work, the influence of oxidised nitrogen forms on the electricity...
-
Novel sugar-based nickel-tungsten carbide catalysts for dry reforming of hydrocarbons
PublikacjaThe search for new materials for dry reforming of hydrocarbons with high activity, stability, and ease of synthesis is still one of the main directions of research in the field of heterogeneous catalysis. Traditional methods of carbide synthesis require the use of combustible gases of petrochemical origin. The search for new catalysts based on renewable and safe carbon sources is highly demanded. Therefore, we report WC and Ni-WC...
-
Swarm-Assisted Investment Planning of a Bioethanol Plant
PublikacjaBioethanol is a liquid fuel for which a significant increase in the share of energy sources has been observed in the economies of many countries. The most significant factor in popularizing bioethanol is the profitability of investments in construction of facilities producing this energy source, as well as the profitability of its supply chain. With the market filled with a large amount of equipment used in the bioethanol production...
-
Partially Isolated Multi-Active Bridge DC-DC Converter with Bidirectional EV Charging Ports
PublikacjaThere is a growing interest in multiport converters due to their ability to interconnect various energy sources and loads using reduced number of components. Regarding electric vehicle (EV) chargers connection, existing multiport solutions either lack scalability, featuring only one isolated charging port or the operation of ports depend on each other, complicating the converter control algorithm. This article proposes a partially...
-
Wastewater Engineering 2020/21 (Environmental Engineering, II stopnia, stacjonarne, II semestr))
Kursy OnlineWastewater sources and flows Wastewater characterization based on physical and biodegradation criteria Preliminary treatment unit operations (screens, grit chambers, primary clarifiers) Biological processes (suspended growth vs. attached growth, hybrid systems, granular sludge) for wastewater treatment. Principles of biological nutrient removal (nitrification, denitrification, enhanced biological P removal, anammox). Implementation...
-
The Simulation of Activated Sludge System for Optimization of Predictive Aeration at Large WWTP
PublikacjaEffective use of biodegradable substrates as an internal carbon sources (ICS) for denitrification and EBPR and predicting performance of aeration systems during nitrification in activated sludge bioreactors, may be useful in realization the sustainable development by potentially saving energy consumption at WWTPs. A large number of WWTPs use activated sludge systems with an integrated removal of carbon, nitrogen and phosphorus...
-
Potential of Functionalized Polyolefins in a Sustainable Polymer Economy: Synthetic Strategies and Applications
PublikacjaPolymers play a crucial role in our modern life as no other material exists that is so versatile, moldable, and lightweight. Consequently, the demand for polymers will continue to grow with the human population, modernization, and technological developments. However, depleted fossil resources, increasing plastic waste production, ocean pollution, and related growing emission of greenhouse gases has led to a change in the way we...
-
Negative carbon dioxide gas power plant integrated with gasification of sewage sludge
PublikacjaOne of the primary objectives of the negative carbon dioxide gas power plant (nCO2PP) is to develop an innovative technology confirming the possibility of the use of sewage sludge to produce electricity while having a positive impact on the environment. In this paper, a mathematical model is presented to estimate thermodynamic parameters of the system in relation to the gasification process and changes in such parameters in the...
-
Modelling of the Polish Electricity Generation Subsystem in MARKAL Program with Emphasis on the EU Emissions Trading Scheme
PublikacjaThis paper addresses issues related to greenhouse gas emissions in the European Union and measures to reduce them, in particular the European Emissions Trading Scheme (EU ETS). A model of the Polish electricity generation subsystem, taking into account EU ETS mechanisms, has been developed using the MARKAL optimization package. Data collected on the basis of available projects, regulations and statistics were entered into the model....
-
Digestate Quality Originating from Kitchen Waste
PublikacjaThis paper examines the influence of biomass directed to anaerobic digestion on the quality of digestate, specifically focusing on the presence of undesirable substances, such as plastics, including biodegradable ones. It analyses the susceptibility of selected bioplastics to degradation and addresses the problem of reliable identification of microplastics in both feedstock—directed to anaerobic digestion—and produced digestate....
-
HIERARCHICAL CYCLES IN MODERN POWER SYSTEMS – EXERGY ANALYSIS UNDER PART LOADS
PublikacjaThe aim of the paper is to investigate thermodynamic efficiency of advanced hierarchic power cyclesunder partial loads by using of exergy analyze. Advanced hierarchical power systems arecomposed of few energy conversion cycles, most common are steam and gas cycles in various configurations, but they may contain fuel cells, ORC, lithium bromide absorption chillers and others. Moreover hierarchical cycles can be powered by several...
-
Analytical fluctuation enhanced sensing by resistive gas sensors
PublikacjaResistance fluctuations across polarised resistive gas sensors were studied in detail to evaluate sensor working conditions for detecting methane and ammonia at various concentrations. The 1/f noise component typically dominates other noise sources up to a few kHz and can be utilised to improve gas selectivity when compared with measurements of the sensor DC resistance. The Arrhenius plot was created and the activation energy for...
-
Cascaded Buck Hybrid Interlink Converter for Multiple-Input / Multiple-Output Operation
PublikacjaThe provision of isolated- and non-isolated DC output voltages by Power electronics power-conditioning devices in the recent ‘green-energy-revolution’ era is on course. In this paper, a structure for multi-input multi-output(MIMO) DC–DC buck converter is proposed to generate output voltages of varying levels with fewer component-count. The DC output voltage of each of the constituting buck converters can be used independently or...
-
INDUSTRIAL HERITAGE IN “SACRIFICE ZONES”. THE POTENTIAL OF BOCAMINA I & II THERMOELECTRIC IN CORONEL, CHILE
PublikacjaThis work aims to present the recovery potential of the Chilean Sacrifice Zones, urban areas affected by high amounts of pollution caused by industrial activities. It centers in the case of “Bocamina I & II”, two Thermoelectric based in the city of Coronel, southern Chile. A settlement historically related to the mining processes. These plants operated for decades supplying the national energy grid and are seen as both symbols...
-
The assessment of solar photovoltaic in Poland: the photovoltaics potential, perspectives and development
PublikacjaThe following article explains the current condition of the photovoltaics sector both in Poland and worldwide. Recently, a rapid development of solar energy has been observed in Poland and is estimated that the country now has about 700,000 photovoltaics prosumers. In October 2021, the total photovoltaics power in Poland amounted to nearly 5.7 GW. The calculated technical potential of photovoltaics in Poland is 153.484 PJ (42.634...
-
Maximum Power Point Technique (MPPT) for PV System Based on Improved Pert and Observe (P&O) Method with PI Controller
PublikacjaPhotovoltaic power generation system has key rule in electricity production. Although, it is clean renewable energy with unlimited resources but it has some drawbacks in efficiency. In order to maximize the efficiency, PV array must drive at maximum power point. For the reason so, several algorithms are used in PV system to track MPP and reduce the...
-
Coffee silverskin as a potential bio-based antioxidant for polymer materials: Brief review
PublikacjaCoffee silverskin is one of the by-products generated by the coffee industry. Although it is not the most burdensome one, because it stands only for ~4.2 wt % of coffee, it seems like an auspicious raw material for industrial processes. Coffee silverskin is characterized by a relatively low moisture content of ~5–7%, so it often does not require quite energy-consuming drying processes. The chemical composition of coffee silverskin,...
-
Synthesis of eosin modified TiO2 film with co-exposed {001} and {101} facets for photocatalytic degradation of para-aminobenzoic acid and solar H2 production
PublikacjaOwing to the increasing photosensitivity and DNA damage properties of para-aminobenzoic acid (PABA), concerns have been raised over the exposure of humans to PABA. Solar light-driven photocatalysis (SPC) provides a promising solution for the effective removal of organic pollutants especially when directed towards sulfate radical (SO4−) production. Herein, we have developed a sulfite-enhanced SPC using Eosin-Y sensitized TiO2/Ti...
-
Investigating BiMeVOx compounds as potential photoelectrochemical and electrochemical materials for renewable hydrogen production
PublikacjaIn this study, BiMeVOx compounds (where Me: Co, Mo, Ce, Zr) were synthesized and characterized as potential photoelectrochemical materials for solar water splitting, the hydrogen evolution reaction (HER), and oxygen evolution reaction (OER). The analysis confirmed the successful formation of phase BiMeVOx compounds with the desired crystal structure. Among the tested materials, BiCoVOx(800) showed the highest photocurrent density...
-
HYDROACOUSTIC NOISE MEASUREMENTS
PublikacjaThe paper deals mainly with investigation of underwater noise that propagation is in shallow water. In this paper has been presented the experimental investigation results concerning the distribution of the sound field pressure generated by moving ships in the shallow water at the small distance from the ship. The main acoustical characteristics describing features of the field are spectrograms in pseudo 3D system – distance and frequency...
-
Wielokryterialna analiza porównawcza lokalizacji źródeł wytwórczych energii elektrycznej
PublikacjaArtykuł przedstawia ranking lokalizacji czterech źródeł wytwórczych energii elektrycznej: biogazowni rolniczej, biogazowni utylizacyjnej oraz dwóch elektrowni fotowoltaicznych, wykonany przy użyciu połączonych metod Analitycznego Procesu Hierarchicznego (AHP) oraz taksonomii numerycznej. Omówiono zalety połączenia metod, przedstawiono przykład zastosowania oraz wskazano kryteria o największym i najmniejszym wpływie na realizację...
-
Perfectly Wetting Mixtures of Surfactants from Renewable Resources: The Interaction and Synergistic Effects on Adsorption and Micellization
PublikacjaThis paper presents a study of the surface properties of mixtures of surfactants originating from renewable sources, i.e., alkylpolyglucoside (APG), ethoxylated fatty alcohol (AE), and sodium soap (Na soap). The main objective was to optimize the surfactant ratio which produces the highest wetting properties during the analysis of the solution of the individual surfactants, twoand three-component mixtures, and at different pH values....
-
Manufacturing and Recycling Impact on Environmental Life Cycle Assessment of Innovative Wind Power Plant Part 2/2
PublikacjaThe process of conversion of wind kinetic energy into electricity in innovative wind power plant emits practically no harmful substances into the environment. However, the production stage of its components requires a lot of energy and materials. The biggest problem during production plan-ning process of an innovative wind power plant is selection of materials and technologies and, consequently, the waste generated at this stage....
-
A unified approach to the analysis of electric energy and fuel consumption of cars in city traffic
PublikacjaForecasting fuel and electricity consumption is an important factor determining the direction of changes in road engineering solutions, traffic management, selection of routes for public transport and development more efficient car drive systems. With a reliable and easy-to-use computational tool, it is possible to reduce the consumption of primary energy sources and reduce the emission of toxic compounds in cities. An analysis...
-
Advances and Trends in Non-Conventional, Abrasive and Precision Machining 2021
PublikacjaIn the modern, rapidly evolving industrial landscape, the quest for machining and production processes consistently delivering superior quality and precision is more pronounced than ever. This necessity and imperative are driven by the increasing complexity in the design and manufacturing of mechanical components, an evolution in lockstep with the swift advancements in material science. The real challenge of this evolution lies...
-
DTWO Cyfrowe bliźniaki dla produkcji morskiej energii wiatrowej i popytu rynkowego
ProjektyProjekt realizowany w Katedra Inteligentnych Systemów Interaktywnych zgodnie z porozumieniem Project 101146689 — DTWO z dnia 2024-04-23
-
LabVIEW-based intelligent system of protection against electric shock for photovoltaic installations
PublikacjaEvaluation of shock hazard in installations with photovoltaic sources of energy is more complicated than in a conventional low voltage system. In case of earth fault in photovoltaic generators, that are connected to the AC power public grid, a composite waveform of earth fault current in the installation may occur. For composite waveforms, the safety criteria should be modified. The paper considers the effect of the composite waveforms...
-
Photovoltaic bulk heterojunctions with interpenetrating network based on semiconducting polymers
PublikacjaPhotovoltaic cells are supposed to be the most common generators of useful electricity in the nearest future as they utilize inexhaustible carriers of renewable energy called photons. Despite the fact that 95% of worldwide applied photovoltaic devices are based on inorganic semiconductors the area of organic photovoltaics grows successively due to possibility of considerable reduction of manufacturing costs. Since the Heeger's...
-
Deep eutectic solvents – Ideal solution for clean air or hidden danger?
PublikacjaThe industrial sector is one of the fastest-growing sources of greenhouse gases, due to its excessive energy consumption to meet the rapidly growing demand for energy-intensive products. The use of deep eutectic solvents (DESs) has been studied extensively in order to cope with these harmful gases, but their usage can be an issue in respect to ecological reasons. Do deep eutectic solvents harm the atmosphere? Yes, these solvents...
-
The Effect of Laser Re-Solidification on Microstructure and Photo-Electrochemical Properties of Fe-Decorated TiO2 Nanotubes
PublikacjaFossil fuels became increasingly unpleasant energy source due to their negative impact on the environment; thus, attractiveness of renewable, and especially solar energy, is growing worldwide. Among others, the research is focused on smart combination of simple compounds towards formation of the photoactive materials. Following that, our work concerns the optimized manipulation of laser light coupled with the iron sputtering to...
-
Performance and emission characteristics of diesel engines running on gaseous fuels in dual-fuel mode
PublikacjaConventional fossil fuels are being substituted with alternative green fuels because of their greenhouse gas emissions and pollution problems, which pose a severe threat to the environment. Several studies have reported the usage of biodiesel and gaseous fuels in both single and dual-fuel modes. Gaseous fuels such as producer gas, biogas, syngas, and hydrogen produced from renewable biomass could potentially be used along with...
-
Maximizing Bio-Hydrogen and Energy Yields Obtained in a Self-Fermented Anaerobic Bioreactor by Screening of Different Sewage Sludge Pretreatment Methods
PublikacjaEgypt faces significant challenges in managing its sewage sludge generated in large quantities from wastewater treatment plants. This study investigates the feasibility of utilizing sewage sludge as a renewable resource for hydrogen production through anaerobic digestion at the 100 L bioreactor level. Hydrogen is considered a promising alternative energy source due to its high energy content and environmental benefits. To optimize...
-
Onboard Energy Storage and Power Management Systems forAll-Electric Cargo Vessel Concept
PublikacjaThis paper presents an innovative approach to the design of a forthcoming, fully electric-powered cargo vessel. This work begins by defining problems that need to be solved when designingvessels of this kind. Using available literature and market research, a solution for the design of apower management system and a battery management system for a cargo vessel of up to 1504 TEUcapacity was developed. The proposed solution contains...
-
The Influence of a Photovoltaic Micro-Installation on the Low-Frequency Parameters of Electricity at PCC and Its Impact on the Thermal Characteristics of Selected Devices
PublikacjaThis manuscript illustrates the measurement results of parameters describing the quality of energy at the PCC (point of common coupling) of a photovoltaic micro-installation that can significantly affect devices in the same power grid. The analyses reflecting heating of selected devices used in domestic installations, which were performed in an isolated laboratory environment, are also indicated. The conducted study aimed at checking...
-
Signals features extraction in radioisotope liquid-gas flow measurements using wavelet analysis
PublikacjaKnowledge of the structure of a flow is significant for the proper conduct of a number of industrial processes. In this case, a description of a two-phase flow regimes is possible by use of the time-series analysis in time, frequency and state-space domain. In this article the Discrete Wavelet Transform (DWT) is applied for analysis of signals obtained for water-air flow using gamma ray absorption. The presented method was illustrated...
-
Novel, Fully Biobased Semicrystalline Polyamides
PublikacjaNovel, semicrystalline polyamides and co(polyamides) were synthesized from biobased sebacic acid (SA), 2,5-diamino-2,5-dideoxy-1,4;3,6-dianhydroiditol (diaminoisoidide, DAII) as well as from 1,4-diaminobutane (DAB), also known as putrescine in nature. Low molecular weight polyamides were obtained by melt polycondensation of the salts based on these monomers or by interfacial polycondensation. In order to increase their molecular...
-
Wastewater Engineering 2021/22 (Environmental Engineering, II stopnia, stacjonarne, II semestr))
Kursy OnlineWastewater sources and flows Wastewater characterization based on physical and biodegradation criteria Preliminary treatment unit operations (screens, grit chambers, primary clarifiers) Biological processes (suspended growth vs. attached growth, hybrid systems, granular sludge) for wastewater treatment Principles of biological nutrient removal (nitrification, denitrification, enhanced biological P removal, anammox) Implementation...
-
Wastewater Engineering 2022/23 (Environmental Engineering, II stopnia, stacjonarne, II semestr))
Kursy OnlineWastewater sources and flows Wastewater characterization based on physical and biodegradation criteria Preliminary treatment unit operations (screens, grit chambers, primary clarifiers) Biological processes (suspended growth vs. attached growth, hybrid systems, granular sludge) for wastewater treatment Principles of biological nutrient removal (nitrification, denitrification, enhanced biological P removal, anammox) Implementation...
-
Wastewater Engineering 2024/25 (Environmental Engineering, II stopnia, stacjonarne, II semestr)
Kursy OnlineWastewater sources and flows Wastewater characterization based on physical and biodegradation criteria Preliminary treatment unit operations (screens, grit chambers, primary clarifiers) Biological processes (suspended growth vs. attached growth, hybrid systems, granular sludge) for wastewater treatment Principles of biological nutrient removal (nitrification, denitrification, enhanced biological P removal, anammox) Implementation...