wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: MODEL-ORDER REDUCTION, A POSTERIORI ERROR ESTIMATOR, FINITE ELEMENT METHOD.
-
Soft-decision schemes for radar estimation of elevation at low grazing angles
PublikacjaIn modern radars, the problem of estimating elevation angle at low grazing angles is typically solved using superresolution techniques. These techniques often require one to provide an estimate of the number of waveforms impinging the array, which one can accomplish using model selection techniques. In this paper, we investigate the performance of an alternative approach, based on the Bayesian-like model averaging. The Bayesian...
-
Numerical simulation of hardening of concrete plate
PublikacjaThe paper presents a theoretical formulation of concrete curing in order to predict temperature evolution and strength development. The model of heat flow is based on a well-known Fourier equation. The numerical solution is implemented by means of the Finite Difference Method. In order to verify the model, the in situ temperature measurements at the top plate of a road bridge were carried out. A high agreement between numerical...
-
A novel sandwich footbridge - Practical application of laminated composites in bridge design and in situ measurements of static response
PublikacjaA novel sandwich composite footbridge is presented in the paper, as an example of practical application of laminated composites in civil engineering. The in situ static load tests of the footbridge before its acceptation for exploitation are shown and discussed. The results are compared with the corresponding ones from a numerical equivalent single layer model of the sandwich structure created within the framework of finite element...
-
Alicja Sekuła dr hab. inż.
Osoby- 2017 r. - stopień doktora habilitowanego nauk ekonomicznych w dziedzinie ekonomia, dyscyplina - finanse; Szkoła Główna Handlowa, Kolegium Zarządzania i Finansów, - 2003 r. - stopień doktora nauk ekonomicznych w dziedzinie ekonomia, dyscyplina - ekonomia; Politechnika Gdańska, Wydział Zarządzania i Ekonomii, - 1997 r. - tytuł magister inżynier - Politechnika Gdańska, Wydział Zarządzania i Ekonomii, - 1996 r. - tytuł magister inżynier...
-
Progressive failure analysis of laminates in the framework of 6-field nonlinear shell theory
PublikacjaThe paper presents the model of progressive failure analysis of laminates incorporated into the 6-field non-linear shell theory with non-symmetrical strain measures of Cosserat type. Such a theory is specially recommended in the analysis of shells with intersections due to its specific kinematics including the so-called drilling rotation. As a consequence of asymmetry of strain measures, modified laminates failure criteria must...
-
Numerical estimation of the pile toe and shaft unit resistances during the installation process in sands
PublikacjaNumerical simulations of a pile jacking were carried out. A Coupled Eulerian–Lagrangian (CEL) formulation was used to treat with large deformation problems. An Abaqus, a commercial Finite Element Method software suit, was used as a computing environment. The Mohr–Coulomb constitutive model was applied and the Coulomb model of friction was used to describe pile-soil interaction. Calculations were made for three different pile diameters....
-
Heavy Duty Vehicle Fuel Consumption Modelling Based on Exploitation Data by Using Artificial Neural Networks
PublikacjaOne of the ways to improve the fuel economy of heavy duty trucks is to operate the combustion engine in its most efficient operating points. To do that, a mathematical model of the engine is required, which shows the relations between engine speed, torque and fuel consumption in transient states. In this paper, easy accessible exploitation data collected via CAN bus of the heavy duty truck were used to obtain a model of a diesel...
-
Ultrasonic Tomography of Brick Columns Based on FEM Calculations
PublikacjaUltrasonic tomography is one of the most developed method of non-destructive testing. Despite being used mainly in medicine, it is becoming more and more popular as a method for monitoring of structural elements. It allows to examine the internal structure and technical condition of the tested element. This paper investigates the influence of crosssectional geometry on an obtained tomographic image. Wave propagation signals were...
-
Detection of Delamination in Laminate Wind Turbine Blades Using One-Dimensional Wavelet Analysis of Modal Responses
PublikacjaThis paper demonstrates the effectiveness of a nondestructive diagnostic technique used to determine the location and size of delamination in laminated coatings of wind turbine blades. This is realized based on results of numerical and experimental investigations obtained by the use of the finite element method (FEM) and laser scanning vibrometry (LSV). The proposed method is based on the one-dimensional continuous wavelet transform...
-
Introduction to Numerical Simulation
Kursy OnlineCourse description: This interdisciplinary course provides an introduction to computational techniques for the simulation of a broad range of engineering and physical systems. Concepts and methods discussed are widely illustrated by applications drawn from electrical, mechanical, and chemical engineering. Topics include: mathematical formulations of simulation problems; sparse direct and iterative linear system solution techniques,...
-
Chosen aspects of skeletal system modeling: Numerical solid and shell models of femur part
PublikacjaThe purpose of this paper is to present a new method of femur part modeling by using the finite element method. This method treats a femur part as a system composed of cortical and trabecular bone. For the purpose of determining a proper shape of femur part model there were created three models: a) the first one describes a femur part as a solid structure; b) the second one describes a femur part as a connection of cortical bone...
-
A three-dimensional periodic beam for vibroacoustic isolation purposes
PublikacjaThis paper presents results of investigations on a three-dimensional (3-D) isotropic periodic beam. The beam can represent a vibroacoustic isolator of optimised dynamic characteristics in the case of its longitudinal, flexural and torsional behaviour. The optimisation process concerned both the widths as well as the positions of particular frequency band gaps that are present in the frequency spectrum of the beam. Since the dynamic...
-
Tropospheric parameters derived from the selected IGS stations in the global tropics for the years 2001-2018
Dane BadawczeThis dataset contains daily GNSS-derived zenith tropospheric delay (ZTD), a posteriori corrected zenith wet delay (ZWD), and precipitable water vapour (PWV) time series. These troposphere-related data were estimated for the period between January 2001 and December 2018, for the 43 International GNSS Service (IGS) stations, located in the global tropics....
-
Experiment-aided virtual prototyping to minimize tool-workpiece vibration during boring of large-sized structures
PublikacjaThe paper presents the author's method of solving the problems of vi-bration suppression during boring of large-sized workpieces by means of an in-novative method of adjusting the rotational speed of the boring bar. It consists in selecting the spindle speed in accordance with the results of the cutting process simulation. The method includes identification of the model of the finite element method of the boring bar. The Root Mean...
-
Modeling of Human Tissue for Medical Purposes
PublikacjaThe paper describes the possibilities offered for medicine by modeling of human tissue using virtual and augmented reality. It also presents three proposals of breast modeling for the use in clinical practice. These proposals are the result of arrangements of medical and computer scientists team (the authors) and will be pursued and implemented in the near future. There is included also a brief description of the most popular methods...
-
Advanced numerical modelling for predicting residual compressive strength of corroded stiffened plates
PublikacjaAn advanced methodology for predicting the residual compressive strength of corroded stiffened plates is developed here using the non-linear finite element method. The non-uniform loss of a plate thickness is accounted for on a macro-scale. In contrast, mechanical properties are changed using the constitutive model to reflect the corrosion degradation impact on a micro-scale. Three different stiffened plate thicknesses are considered,...
-
Electromagnetic Simulation with 3D FEM for Design Automation in 5G Era
PublikacjaElectromagnetic simulation and electronic design automation (EDA) play an important role in the design of 5G antennas and radio chips. The simulation challenges include electromagnetic effects and long simulation time and this paper focuses on simulation software based on finite-element method (FEM). The state-of-the-art EDA software using novel computational techniques based on FEM can not only accelerate numerical analysis, but...
-
Particle Shape Effect on Macroscopic Behaviour of Underground Structures: Numerical and Experimental Study
PublikacjaThe mechanical performance of underground flexible structures such as buried pipes or culverts made of plastics depend not only on the properties of the structure, but also the material surrounding it. Flexible drains can deflect by 30% with the joints staying tight, or even invert. Large deformations of the structure are difficult to model in the framework of Finite Element Method, but straightforward in Discrete Element Methods....
-
Particle Shape Effect on Macroscopic Behaviour of Underground Structures: Numerical and Experimental Study
PublikacjaAbstract: The mechanical performance of underground flexible structures such as buried pipes or culverts made of plastics depend not only on the properties of the structure, but also on the material surrounding it. Flexible drains can deflect by 30% with the joints staying tight, or even invert. Large deformations of the structure are difficult to model in the framework of Finite Element Method, but straightforward in Discrete...
-
Implementation of Extended Kalman Filter with Optimized Execution Time for Sensorless Control of a PMSM Using ARM Cortex-M3 Microcontroller
PublikacjaThis paper addresses the implementation and optimization of an Extended Kalman Filter (EKF) for the Permanent Magnet Synchronous Motor (PMSM) sensorless control using an ARM Cortex-M3 microcontroller. A various optimization levels based on arithmetic calculation reduction was implemented in ARM Cortex-M3 microcontroller. The execution time of EKF estimator was reduced from 260.4 μs to 37.7 μs without loss of accuracy. To further...
-
Dynamics of mechanical model of implant-tissue system in ventral hernia repair
PublikacjaThe paper deals with a finite element modelling of implants in the problem of ventral hernia repair. The synthetic mesh implanted in the abdomen during surgery is here modelled as a membrane structure. Thesystem undergoes the internal abdominal pressure that occurs during the postoperative cough, the load identified in the literature as the main cause of the connection failure and hernia recurrence. The model can be used to estimate...
-
A high-accuracy method of computation of x-ray waves propagation through an optical system consisting of many lenses
PublikacjaThe propagation of X-ray waves through an optical system consisting of many X-ray refractive lenses is considered. Two differential equations are contemplated for solving the problem for electromagnetic wave propagation: first – an equation for the electric field, second – an equation derived for a complex phase of an electric field. Both equations are solved by the use of a finite-difference method. The simulation error is estimated...
-
Numerical Methods for Partial Differential Equations
Kursy OnlineCourse description: This course focuses on modern numerical techniques for linear and nonlinear elliptic, parabolic and hyperbolic partial differential equations (PDEs), and integral equations fundamental to a large variety of applications in science and engineering. Topics include: formulations of problems in terms of initial and boundary value problems; finite difference and finite element discretizations; boundary element approach;...
-
Numerical analyses of novel prefabricated structural wall panels in residential buildings based on laboratory tests in scale 1:1
PublikacjaThe paper presents experimental and numerical investigations on novel prefabricated composite building wall panels for residential building constructions. The wall panels were composed of reinforced concrete ribbed elements with the core from the EPS foam as the thermal insulation. The wall panels in the full-scale 1:1 were subjected to vertical loads. In the first step, the experiments were analysed with simple usual static methods....
-
A technique of experiment aided virtual prototyping to obtain the best spindle speed during face milling of large-size structures
PublikacjaThe paper presents an original method concerning vibration suppression problem during milling of large-size and geometrically complicated workpieces with the use of novel way of selecting the spindle speed. This consists in repetitive simulations of the cutting process for subsequent values of the spindle speed, until the best vibration state of the workpiece is reached. An appropriate method of obtaining a computational model,...
-
Laboratory Determination of Burger's Model Parameters for Visco-elastic Analysis of Road Pavement Materials
PublikacjaBurger's Model is one of those models that describes performance of asphalt mixtures. Its parameters can be used in road construction analysis based on visco-elastic properties in wide variety of temperatures using dedicated programs (e.g. Veroad) or in Finite Element Method (FEM). Parameters of Burger's Model can be used for example in prediction of low temperature cracking in low winter temperatures or permanent deformation...
-
Comparison of noise reduction methods in radiometric correlation measurements of two-phase liquid-gas flows
PublikacjaTwo-phase liquid-gas flows occur frequently in the mining, energy, chemical, and petrochemical industries. One of non-contact methods used to analyse these flows is the gamma ray absorption method. However, the signals received from radiation detectors contain a significant stochastic noise, which makes them difficult to analyse. The article describes four methods of noise reduction in cross-correlation measurements of water-air...
-
Hybrid Method Analysis of Unshielded Guiding Structures
PublikacjaA combination of mode matching, finite element methods and generalized impedance matrix is presented in a context of propagation problems for open guiding structures. The computational domain is divided into two regions: the first one is a circular cylinder containing whole guiding structure and the second one surrounds this artificial cylinder. The impedance matrix is calculated with the use of finite element method in the first...
-
Emilia Miszewska dr inż.
OsobyEmilia Miszewska urodziła się w 1986 roku w Gdańsku. Ukończyła Szkołę Podstawową nr 17 w Gdańsku z klasami sportowymi o profilu pływanie oraz Liceum Sportowe nr 11 im. Janusza Kusocińskiego w Gdańsku. W 2005 roku rozpoczęła jednolite studia magisterskie na Wydziale Inżynierii Lądowej i Środowiska, które ukończyła w roku 2011, broniąc pracę dyplomową pt. „Analiza i opracowanie wytycznych zabezpieczenia pożarowego oraz planu...
-
Subcritical bifurcation of free elastic shell of biological cluster
PublikacjaIn this paper we will investigate symmetry-breaking bifurcation of equilibrium forms of biological cluster. A biological cluster is a two-dimensional analogue of a gas balloon. The cluster boundary is connected with its kernel by elastic links. The inside part is filled with compressed gas or fluid. Equilibrium forms of biological cluster can be found as solutions of a certain second order ordinary functional-differential equation...
-
FEM modelling of stress and strain distribution in weld joints of steel sandwich panels
PublikacjaThe development of laser welding technology has enabled the mass production of thin-walled structures, including steel sandwich panels. The technology of joining plating panels with stiffeners by welding allows us to create joints with a specific geometry and material properties. In comparison with other types of joints, laser welds are characterized by their specific behaviour under cyclic load and, as a consequence, a different...
-
FEM and experimental investigations of concrete temperature field in the massive stemwall of the bridge abutment
PublikacjaThe paper deals with the prediction of early-age concrete temperature of cast-in-place stemwall of the bridge abutment. The considered object is an arch bridge located in Gda´nsk. In the case of massive structures, it is particularly important to not exceed the temperature difference between the core and the concrete surface. Too high temperature gradient generates an increase in thermal stresses, what could be the reason of exceeding...
-
Closed Form Constraint Equations Used to Express Frictionless Slip of Multibody Systems Attached to Finite Elements—Application to a Contact between a Double Pendulum and a Beam
PublikacjaThis paper focuses on the numerical modeling of the dynamics of mechanical systems. Robots that can inspect high-voltage lines inspired this research. Their control systems must anticipate potential grab positions appropriately. We intend to formulate equations dedicated to the numerical description of the robot/cable contact. The investigated problem is not straightforward, since parts of the modeled systems are numerically inhomogeneous....
-
A DISCRETE-CONTINUOUS METHOD OF MECHANICAL SYSTEM MODELLING
PublikacjaThe paper describes a discrete-continuous method of dynamic system modelling. The presented approach is hybrid in its nature, as it combines the advantages of spatial discretization methods with those of continuous system modelling methods. In the proposed method, a three-dimensional system is discretised in two directions only, with the third direction remaining continuous. The thus obtained discrete-continuous model is described...
-
Equivalent Single Layer Models in Free Vibration Analysis of Laminated Multi-Layered Plates
PublikacjaThe performance of selected equivalent single-layer (ESL) models is evaluated within several classical benchmark tests for small amplitude free vibration analysis of multi-layered plates. The authors elaborated their own Finite Element software based on the first-order shear deformation (FOSD) theory with some modifications incorporated including a correction of the transverse shear stiffness and an application of zigzag type functions....
-
Robust Model Predictive Control for Autonomous Underwater Vehicle – Manipulator System with Fuzzy Compensator
PublikacjaThis paper proposes an improved Model Predictive Control (MPC) approach including a fuzzy compensator in order to track desired trajectories of autonomous Underwater Vehicle Manipulator Systems (UVMS). The tracking performance can be affected by robot dynamical model uncertainties and applied external disturbances. Nevertheless, the MPC as a known proficient nonlinear control approach should be improved by the uncertainty estimator...
-
Mechanical compatibility of implants used in hernia repair with abdominal wall
PublikacjaThe paper deals with a membrane model of a synthetic surgical mesh for treatment of abdominal hernia. The authors analyse the compatibility of two implant types with the human wall: Dualmesh Gore and Proceed. The finite element method is applied to simulate tjhe behavior of the proposed model. Due fact that recurrences are usually caused by connection failure, this study is focused on reaction forces in supports representing the...
-
Random field modelling of mechanical behaviour of corroded thin steel plate specimens
PublikacjaThe objective of this work is to explore the possibility of corrosion degradation modelling of thin steel plate specimens with the use of random field approach. The mechanical properties are obtained via the nonlinear Finite Element Analysis with the use of an explicit dynamic solver. The fully nonlinear material model is adopted to obtain the proper stress-strain response. Sensitivity analysis considering the main statistical...
-
The Influence of Articular Cartilage Thickness Reduction on Meniscus Biomechanics
PublikacjaObjective Evaluation of the biomechanical interaction between meniscus and cartilage in medial compartment knee osteoarthritis. Methods The finite element method was used to simulate knee joint contact mechanics. Three knee models were created on the basis of knee geometry from the Open Knee project. We reduced the thickness of medial cartilages in the intact knee model by approximately 50% to obtain a medial knee osteoarthritis...
-
A new open-source software developed for numerical simulations usingdiscrete modeling methods
PublikacjaThe purpose of this work is to present the development of an open-source software based on a discrete description of matter applied to study the behavior of geomaterials. This software uses Object Oriented Programming techniques, and its methodology design uses three different methods, which are the Discrete Element Method (DEM) [F. Donzé, S.A. Magnier, Formulation of a three-dimensional numerical model of brittle behavior, Geophys....
-
Experimental investigation and process parameter optimization of sheet metal bending by line heating method
PublikacjaThe present study is concerned with the experimental investigation of sheet metal deforming by line heating method that incorporates the combined effect of traverse speed of the torch, thickness of the sheet metal, and the number of passes of the torch. For the numerical analysis of metal bending by line heating, the
-
Strength parameters of masonry walls in modelling historic constructions
PublikacjaThe paper presents the determination of the basic material properties of a historic brickwork. Experimental studies were used to identify the basic material properties of bricks. The mechanical properties of the masonry, as an orthotropic homogenized material, were calculated. Then, numerical simulations using the Finite Element Method (FEM) were performed to verify the experimental outcomes. Macromodels with element sizes of 40,...
-
Exact modal absorbing boundary condition for waveguide simulations - discrete Green's function approach
PublikacjaA modal absorbing boundary condition (ABC) based on the discrete Green's function (DGF) is introduced and applied for termination of waveguides simulated by means of the finite-difference time-domain (FDTD) method. The differences between the developed approach and implementations already demonstrated in the literature are presented. By applying DGF, a consistent theoretical approach to modal ABC in the FDTD method is obtained....
-
3-D finite-difference time-domain modelling of ground penetrating radar for identification of rebars in complex reinforced concrete structures
PublikacjaThis paper presents numerical and experimental investigations to identify reinforcing bars using the ground penetrating radar (GPR) method. A novel element of the paper is the inspection of different arrangements of reinforcement bars. Two particular problems, i.e. detection of few adjacent transverse bars and detection of a longitudinal bar located over or under transverse reinforcement, have been raised. An attention was also...
-
On the convergence of a nonlinear finite-difference discretization of the generalized Burgers–Fisher equation
PublikacjaIn this note, we establish analytically the convergence of a nonlinear finite-difference discretization of the generalized Burgers-Fisher equation. The existence and uniqueness of positive, bounded and monotone solutions for this scheme was recently established in [J. Diff. Eq. Appl. 19, 1907{1920 (2014)]. In the present work, we prove additionally that the method is convergent of order one in time, and of order two in space. Some...
-
On the convergence of a finite-difference discretization à la Mickens of the generalized Burgers–Huxley equation
PublikacjaIn this note, we establish the property of convergence for a finite-difference discretization of a diffusive partial differential equation with generalized Burgers convective law and generalized Hodgkin–Huxley reaction. The numerical method was previously investigated in the literature and, amongst other features of interest, it is a fast and nonlinear technique that is capable of preserving positivity, boundedness and monotonicity....
-
The Influence of Selected Parameters of Numerical Modelling on Strains and Stresses at Weld Toe Notch
PublikacjaLatest development in the field of welding technology and prefabrication enabled massive production of thin-walled sandwich structures. Multi-layered sandwich structures are fabricated with the use of high-power CO2 lasers, friction welding, arc welding, hybrid welding, or other technique designed for the special purpose. Steel or aluminium alloy plates with thickness between 1 and 5 mm are connected by internal stiffeners. Strength...
-
Coupled Urban Areas Inundation Model with Interaction Between Storm Water System and Surface Flow - Case Study of Sea Level Impact on Seaside Areas Flooding
PublikacjaInundations are becoming more frequent than ever. What is connected with increasing area of impervious surface in cities. This makes predicting urban flooding and its scale especially important. At the seaside we observe additional conditions such as sea level that makes accurate numerical modelling of issue even harder. With complex approach to the matter which is simultaneous calculation of storm water conduit flow and overland...
-
A study on transverse shear correction for laminated sandwich panels
PublikacjaThe paper presents a study on an application of the First Order Shear Deformation Theory in a linear static analysis of elastic sandwich panels. A special attention has been given to the issue of the transverse shear correction. Two benchmark examples of sandwich plate problems with known reference solutions have been selected for a comparative analysis performed with own Finite Element codes. Interesting results allowed for drawing...
-
A Diagnostic Method Based on Deflection Analysis for Monitoring Post-elastic Response of Beams
PublikacjaA non-destructive diagnostic method based on deflection analysis for monitoring the post-elastic response of beams was developed, and a diagnostic indicator was proposed. The indicator was defined as the second moment of the normalised curvature function about the mid-span, where the curvature was computed from the normalised deflection function. Elastic reference values of the indicator were computed for simply supported beams...