Wyszukiwarka
Wyniki wyszukiwania dla: BENDING PROPERTIES
-
Determination of the Bending Properties of Wire Rope Used in Cable Barrier Systems
PublikacjaThis paper presents research on the bending properties of 3 × 7 19-mm wire rope commonly used in road cable barriers. A total of 19 experimental tests were conducted. In addition, two nonlinear 3D numerical models of the wire rope using beam and solid finite elements were developed. Based on these models, four numerical simulations were carried out. The numerical results were validated against the experimental ones and a very good...
-
A new prototype of piezoelectric bending resonant transducer for analysis of soft tissues properties
PublikacjaThis paper is devoted to a new piezoelectric bending resonant transducer prototype dedicated to the characterization of the mechanical properties of soft tissue. A general description of the actuator’s structure is presented including the basic principles of the measurement. The chosen geometry of the prototype is discussed and compared with the existing version. Constitutive equations are presented for the active and passive layer...
-
On Effective Bending Stiffness of a Laminate Nanoplate Considering Steigmann–Ogden Surface Elasticity
PublikacjaAs at the nanoscale the surface-to-volume ratio may be comparable with any characteristic length, while the material properties may essentially depend on surface/interface energy properties. In order to get effective material properties at the nanoscale, one can use various generalized models of continuum. In particular, within the framework of continuum mechanics, the surface elasticity is applied to the modelling of surface-related...
-
Fracture simulations in concrete beam under bending using a mesoscopic model with cohesive elements
PublikacjaThe main aim of this paper was to investigate a complex fracture process in a concrete beam subjected to 3-point bending test by means of the 2D meso-scale FEM with 4-node cohesive elements embedded in the initial mesh of 3-node solid elements. The material heterogeneity was taken into account by considering 3 different phases (aggregate, cement matrix, ITZs) on the basis of randomly generated internal structure of concrete and...
-
Three-point bending test of sandwich beams supporting the GFRP footbridge design process - validation
PublikacjaSome selected aspects concerning material and construction design issues for pedestrian footbridge made of GFRP composite materials are elaborated in this paper. The analysis is focused on validation tests, which are particularly important because of the advanced technology and materials that are used for this innovative bridge. The considered footbridge is a sandwich-type shell structure comprising of PET foam core and outer skins...
-
The impact of surface slope and calculation resolution on the fractal dimension for fractures of steels after bending-torsion fatigue
PublikacjaThe article presents the results of the fractal dimension measurements on the fatigue fracture surfaces of 10HNAP and S355J2 steels specimens after combined bending-torsion fatigue. For smooth and ring-notched specimens, three loading conditions were analyzed: (1) bending; (2) bending-torsion; and (3) torsion fatigue. Post-failure surface topography measurements were carried out on the entire fracture surfaces using an optical...
-
Textile reinforced concrete members subjected to tension, bending, and in-plane loads: Experimental study and numerical analyses
PublikacjaTextile reinforced concrete has raised increasing research interest during the last years, mainly due to its potential to be used for freeform shell structures involving complex load situations. Yet, most experimental work has focused on test setups with primarily uniaxial loading. In the current work, such setups are complemented with a novel test setup of deep beams, including in-plane bending and shear. Further, nonlinear finite...
-
Assessment of Thermal Stresses in Asphalt Mixtures at Low Temperatures Using the Tensile Creep Test and the Bending Beam Creep Test
PublikacjaThermal stresses are leading factors that influence low-temperature cracking behavior of asphalt pavements. During winter, when the temperature drops to significantly low values, tensile thermal stresses develop as a result of pavement contraction. Creep test methods can be suitable for the assessment of low-temperature properties of asphalt mixtures. To evaluate the influence of creep test methods on the obtained low-temperature...
-
On the Bending of Multilayered Plates Considering Surface Viscoelasticity
PublikacjaWe discuss the bending resistance of multilayered plates taking into account surface/interfacial viscoelasticity. Within the linear surface viscoelasticity we introduce the surface/interfacial stresses linearly dependent on the history of surface strains. In order to underline the surface viscoelasticity contribution to the bending response we restrict ourselves to the elastic behaviour in the bulk. Using the correspondence principle...
-
Bending of a Three-Layered Plate with Surface Stresses
PublikacjaWe discuss here the bending deformations of a three-layered plate taking into account surface and interfacial stresses. The first-order shear deformation plate theory and the Gurtin-Murdoch model of surface stresses will be considered and the formulae for stiffness parameters of the plate are derived. Their dependence on surface elastic moduli will be analyzed.
-
Effect of polymer fibres reinforcement on selected properties of asphalt mixtures
PublikacjaThe paper presents selected results of the research program concerning fibre reinforced asphalt concrete. Aramid-polyalphaolefin fibres was used in this study. Selected properties responsible for low temperature cracking and resistance to permanent deformation are presented in this paper. Low temperature cracking susceptibility was evaluated with the results obtained from bending test of rectangular beams with constant rate of...
-
Micro-cracking pattern recognition of hybrid CNTs/GNPs cement pastes under three-point bending loading using acoustic emission technique
PublikacjaThe generation of microcracks has an important influence on the behaviour of concrete structures. In this study, the acoustic emission (AE) technique was used to investigate the fracture phenomena and micro-cracking behavior of hybrid carbon nanotubes (CNTs, the 1-D allotrope of carbon atoms) and graphene nanoplatelets (GNPs, 2D monolayer of sp2-hybridized carbon atoms), cement composites under three-point bending loading. In...
-
Innovative Cold-formed GEB Section under Bending
PublikacjaThis paper is concerned with the numerical bending capacity study of the innovative cold-formed GEB sections. Both linear buckling analysis and non-linear static analysis incorporating geometric and material nonlinearity were carried out employing a shell structural model. The magnitudes of buckling load and limit load with respect to GEB section depth and thickness were obtained. The opened cold-formed section was tested assuming...
-
FEM simulation of laminate failure in the three point bending
PublikacjaThe paper presents a FEM simulation of failure of laminate subjected to the three point bending. The numeri-cal model is based on the equivalent single layer approach with 6-paramater non-linear shell theory kinematics. It is implemented in the non-commercial FEM code. The failure initiation is detected with the use of Tsai-Wu criterion. After the failure onset the progressive failure process is modelled through the appropriate...
-
Fatigue Bending of V-Notched Cold-Sprayed FeCoCrNiMn Coatings
PublikacjaCold-spray coatings were produced by FeCoCrNiMn high-entropy alloy powders deposited on carbon steel substrate. The coatings were realized at intermediate temperature and high pressure (at 1100 °C and 7 MPa). The coating microstructure was characterized by scanning electron microscopy and X-ray diffraction, revealing a very dense deposition and high flattening ratio of the splatted particles. This had a large influence on the...
-
Influence of steam drying process on wood mechanical properties
PublikacjaResults of influence of gas-steam mixture drying process on mechanical properties of material are presented. Wood species, namely oak (Quercus L.), beech (Fagus L.), pine (Pinus L.) and spruce (Picea K.) from the northern part of Pomerania region in Poland, were subject of air-steam mixture drying process in a laboratory kiln especially arranged for that reason. Measurements of the global coefficient of elasticity and bending strength...
-
The change of mechanical properties of selected wood species after drying process under various conditions
PublikacjaThe result of mechanical properties change of selected wood species after drying process under various parameters are presented. The global elasticity modulus and bending strength for steam dried, air-steam mixture dried and air dried samples as reference were measured. It allowed to reveal the effect of wood stream, air-steam mixture and their temperature on mechanical properties of wood. It has been recognized that steam and...
-
Fractal dimension for bending–torsion fatigue fracture characterisation
PublikacjaFracture surfaces after biaxial fatigue tests were compared using fractal dimension for three types of metallic materials in smooth and notched specimens made of S355J2 and 10HNAP steels and 2017-T4 aluminium alloy, considering both proportional and nonproportional cyclic loading. High-resolution optical 3D measurement studies were performed on the entire fracture surface. A direct correlation between fractal dimension and fatigue...
-
Fractal dimension for bending–torsion fatigue fracture characterisation
Publikacja -
Testing of low temperature behaviour of asphalt mixtures in bending creep test
PublikacjaThe paper presents a method of bending beam test and its importance for evaluation of asphalt mixtures behaviour at low temperatures. Two types of asphalt mixtures: asphalt concrete AC with normal paving grade bitumen and stone mastic asphalt SMA with SBS-modified bitumen were tested. Long-term oven ageing (LTOA) test was also used in the laboratory according to SHRP procedure. The Burgers model was applied and rheological parameters...
-
Effect of elliptical defect orientation on the durability of specimens subjected to cyclic bending
PublikacjaThis work presents the effect of elliptical defects orientation on the durability of specimens made of C45 steel. Three kinds of specimens with elliptical defects in the form of a one-sided notch oriented at different angles 45, 60, and 90 degrees were subjected to cyclic bending (R=-1). The stress state analysis was performed using local and non-local methods to determine an equivalent amplitude of stress, and then the results...
-
Fractal analysis of the bending-torsion fatigue fracture of aluminium alloy
Publikacja -
A general theory for anisotropic Kirchhoff–Love shells with in-plane bending of embedded fibers
PublikacjaThis work presents a generalized Kirchhoff–Love shell theory that can explicitly capture fiber-induced anisotropy not only in stretching and out-of-plane bending, but also in in-plane bending. This setup is particularly suitable for heterogeneous and fibrous materials such as textiles, biomaterials, composites and pantographic structures. The presented theory is a direct extension of classical Kirchhoff–Love shell theory to incorporate...
-
An influence of the ship's block coefficient implementation on the evaluation of it's hull girder bending
PublikacjaAn influence of the three different ways of implementation ship's block coefficient δ (three geometrical models) on the stresses due to wave bending moment have been investigated. Two models have been applied and compared: beam one (description of the shape usingparameters) and FEM shell model (direct representation of the shape). The outcomes have been compared to Polish Register of Shipping (PRS) rules. The results show that...
-
Evaluation of Asphalt Mixture Low-Temperature Performance in Bending Beam Creep Test
PublikacjaLow-temperature cracking is one of the most common road pavement distress types in Poland. While bitumen performance can be evaluated in detail using bending beam rheometer (BBR) or dynamic shear rheometer (DSR) tests, none of the normalized test methods gives a comprehensive representation of low-temperature performance of the asphalt mixtures. This article presents the Bending Beam Creep test performed at temperatures from −20...
-
Influence of Bitumen Type and Asphalt Mixture Composition on Low-Temperature Strength Properties According to Various Test Methods
PublikacjaIn regions with low-temperatures, action transverse cracks can appear in asphalt pavements as a result of thermal stresses that exceed the fracture strength of materials used in asphalt layers. To better understand thermal cracking phenomenon, strength properties of different asphalt mixtures were investigated. Four test methods were used to assess the influence of bitumen type and mixture composition on tensile strength properties...
-
SIMULATIONS OF FRACTURE IN CONCRETE BEAMS UNDER BENDING USING A CONTINUUM AND DISCRETE APPROACH
PublikacjaThe paper describes two-dimensional meso-scale results of fracture in notched concrete beams under bending. Concrete was modelled as a random heterogeneous 4-phase material composed of aggregate particles, cement matrix, interfacial transitional zones and air voids. Within continuum mechanics, the simulations were carried out with the finite element method based on a isotropic damage constitutive model enhanced by a characteristic...
-
Effect of surface on the flexomagnetic response of ferroic composite nanostructures; nonlinear bending analysis
PublikacjaOur analysis incorporates the geometrically nonlinear bending of the Euler-Bernoulli ferromagnetic nanobeam accounting for a size-dependent model through assuming surface effects. In the framework of the flexomagnetic phenomenon, the large deflections are investigated referring to von-Kármán nonlinearity. Employing the nonlocal effects of stress coupled to the gradient of strain generates a scale-dependent Hookean stress-strain...
-
On Nonlinear Bending Study of a Piezo-Flexomagnetic Nanobeam Based on an Analytical-Numerical Solution
PublikacjaAmong various magneto-elastic phenomena, flexomagnetic (FM) coupling can be defined as a dependence between strain gradient and magnetic polarization and, contrariwise, elastic strain and magnetic field gradient. This feature is a higher-order one than piezomagnetic, which is the magnetic response to strain. At the nanoscale, where large strain gradients are expected, the FM effect is significant and could be even dominant. In...
-
Multi-scale modelling of concrete beams subjected to three-point bending
PublikacjaW artykule przedstawiono wyniki numeryczne MES dwuskalowego modelowania belek betonowych z nacięciem na poziomie skali makro i mezo. Obliczenia wykonano przy wykorzystaniu modelu degradacji sztywności z nielokalnym osłabieniem. Beton został opisany na poziomie skali mezo jako stochastyczny materiał 3-składnikowy złożony z kruszywa, zaczynu cementowego oraz stref kontaktu. Natomiast na poziomie skali makro został opisany jako materiał...
-
Experimental investigations of damage evolution in concrete during bending by continuous micro-CT scanning
PublikacjaThe paper describes experimental investigation results of fracture in notched concrete beams under quasi-static three-point bending. To visualize 3D fracture in concrete under bending, an extended X-ray micro-computed tomography system was used, i.e. the tomography system SkyScan 1173 was connected to the loading machine ISTRON 5569. This combined system enabled to shot images of deforming concrete beams during a continuous deformation...
-
A COMPARISON OF WEAR PROPERTIES OF WATER LUBRICATED NBR AND PTFE SLIDING BEARINGS
PublikacjaThe excessive wear of a journal shaft can be caused by many factors, for example, working conditions (e.g., temperaturę, slip speed, the type of lubricant), pressure, the type of material used on the bearings and shafts and their roughness, as well as contamination remaining in the system. This paper presents the roughness profiles co-operating with a rubber (NBR) and polytetrafluoroethylene (PTFE) bushes. The conditions of cooperation...
-
The effect of external load on ultrasonic wave attenuation in steel bars under bending stresses
PublikacjaThe stress state in deformed solids has a significant impact on the attenuation of an ultrasonic wave propagating through the medium. Measuring a signal with certain attenuation characteristics can therefore provide useful diagnostic information about the stress state in the structure. In this work, basic principles behind a novel attenuation-based diagnostic framework are introduced. An experimental study on steel bars under three-point...
-
The influence of welding heat input on the quality and properties of high strength low-alloy dissimilar steel butt joints
PublikacjaThe paper presents the results of non-destructive and destructive tests of dissimilar highstrength low-alloy S460ML and S460N steel butt joints. These steels are characterized by similar mechanical properties, but their carbon equivalent CeIIW values are much different. The joints were made using different values of heat input for each welding bead. They were tested by non-destructive methods: visual, penetrant, radiographic and...
-
Effect of bending-torsion on fracture and fatigue life for 18Ni300 steel specimens produced by SLM
PublikacjaIn this study, different fracture surfaces caused by fatigue failure were generated from 18Ni300 steel produced by selective laser melting (SLM). Hollow round bars with a transverse hole were tested under bending-torsion to investigate the crack initiation mechanisms and fatigue life. Next, the post-failure fracture surfaces were examined by optical profilometer and scanning electron microscope. The focus is placed on the relationship...
-
Impact of reclaimed asphalt pavement (RAP) on low-temperature properties of asphalt concrete
PublikacjaHot mix recycling is a practice which enables reusing materials from old asphalt pavements. Current Polish regulations allow usage of RAP only for binder and base courses, and its amount is limited. Asphalt mixtures with RAP material have to fulfil requirements stated for typical asphalt mixtures. The research presents low-temperature properties of twelve different asphalt concretes with RAP material, determined using three-point...
-
The energy approach to fatigue crack growth of S355 steel welded specimens subjected to bending
PublikacjaThe study presents the results of the research on the rate of fatigue crack growth subjected to bending in the ferritic-pearlitic structure. The studies were carried out at a constant amplitude of the moment and at various values of the load ratios R and at the operating frequency of the machine of 28.4 Hz. Flat specimens made of S355 steel and with fillet welds and with double-sided blunt external notches as well as concave...
-
Sestaveni Smerne Krivky Modulu Tuhosti Pro Zkoumani Nizkotrplotnich Vlastnosti (Developing of Stiffness Master Curve for Analysis of Low Temperature Properties)
PublikacjaV prispevku je predstaven novy postup pro sestrojeni smernych tuhostnich krivek. Nizkoteplotni vlastnosti asfaltove smesi byly stanoveny za vyuziti zkousky dotvarovani pri tribodovem ohybu. Motivem tohoto vyzkumu je skutecnost, ze metody hodnoceni nizkoteplotniho chovani asfaltovych smesi, nove zavedenych v Polsku, nejsou dostatecne. V zaveru jsou prezentovany smerne krivky tuhosti beznych asfaltovych smesi vyuzivanych v Polsku.
-
Three-Dimensional Fractography for Conventional and Additive Manufactured Steels After Bending-Torsion Fatigue
PublikacjaIn this study, fracture surface topography parameters were measured to investigate the effects of multiaxial loading. In order to assess the metrological aspects of fracture for notched specimens made of high-strength steels processed by both conventional and additively manufacturing (AM) techniques, an optical surface profilometer was used. Three bending moment to torsion moment ratios (B/T) were studied, i.e. 2, 1 and 2/3. The...
-
Bending Moment Control and Weight Optimization in Space Structures by Adding Extra Members in the Optimal Locations
PublikacjaThis paper investigates the reduction of bending moment in critical members by adding some extra members in the optimum location. Instead of enlarging the size of members to resist the moment, eight additional members are added in the optimum location to reduce the bending moment in the critical members. The total weight of the proposed structure with extra members is less than that of the original structure that resists the induced...
-
Mechanical, thermo-mechanical properties of epoxy/glass composites with submicron particles
PublikacjaIn this research the influence of submicron zinc oxide and silicon dioxide particles on mechanical, thermo-mechanical properties of epoxy matrix composites reinforced with glass fibres was investigated. Composites were fabricated using hand lay-up method. Materials contained 39-41 wt.% of glass fibres. The bending tests, dynamic mechanical analysis and tribological tests were performed on each group of composites and also for...
-
Fracture surface formation of notched 2017A-T4 aluminium alloy under bending fatigue
PublikacjaThe effect of cyclic loading on facture surface topology in notched components made by aluminium alloys is not completely clear. Fractogra-phy and fracture mechanics can help to understand this interdependency. This paper aims to study the distribution of the fracture surface roughness of notched 2017A-T4 aluminium alloy after bending fatigue using an optical focus-variation surface measurement technique by applying the fracture...
-
Coda wave interferometry in monitoring the fracture process of concrete beams under bending test
PublikacjaEarly detection of damage is necessary for the safe and reliable use of civil engineering structures made of concrete. Recently, the identification of micro-cracks in concrete has become an area of growing interest, especially using wave-based techniques. In this paper, a non-destructive testing approach for the characterization of the fracture process was presented. Experimental tests were made on concrete beams subjected to mechanical...
-
A general isogeometric finite element formulation for rotation‐free shells with in‐plane bending of embedded fibers
PublikacjaThis article presents a general, nonlinear isogeometric finite element formulation for rotation-free shells with embedded fibers that captures anisotropy in stretching, shearing, twisting, and bending - both in-plane and out-of-plane. These capabilities allow for the simulation of large sheets of heterogeneous and fibrous materials either with or without matrix, such as textiles, composites, and pantographic structures. The work...
-
Experimental investigation and process parameter optimization of sheet metal bending by line heating method
PublikacjaThe present study is concerned with the experimental investigation of sheet metal deforming by line heating method that incorporates the combined effect of traverse speed of the torch, thickness of the sheet metal, and the number of passes of the torch. For the numerical analysis of metal bending by line heating, the
-
The crack surface morphology investigation of S355J2 steel after bending-torsion fatigue
Publikacja -
A new anisotropic bending model for nonlinear shells: Comparison with existing models and isogeometric finite element implementation
PublikacjaA new nonlinear hyperelastic bending model for shells formulated directly in surface form is presented, and compared to four existing prominent bending models. Through an essential set of elementary nonlinear bending test cases, the membrane and bending stresses of each model are examined analytically. Only the proposed bending model passes all the test cases, while the other bending models either fail or only pass the test cases for...
-
Size effect in concrete beams under bending – influence of the boundary layer and the numerical description of cracks
PublikacjaIn the paper the size effect phenomenon in concrete is analysed. The results of numerical simulations of using FEM on geometrically similar un-notched and notched concrete beams under bending are presented. Concrete beams of four different sizes and five different notch heights under three-point bending test were simulated. In total 18 beams were analysed. Two approaches were used to describe cracks in concrete. First, eXtended...
-
Experimental Investigations of Fracture Process Using DIC in Plain and Reinforced Concrete Beams under Bending
PublikacjaThe fracture behaviour of concrete and reinforced concrete beams under quasi-static three-point bending was comprehensively investigated with experiments at laboratory scale. The eight various concrete mixes were tested. The influence of the shape, volume and size of aggregate particles and reinforcement on concrete fracture under bending was studied. Displacements on the surface of concrete beams were measured by means of the...
-
Technical Mechanics 2 (PG_00049753), I stop, En, [W,C], zima 22/23
Kursy OnlineLectures and tutorials devoted to basic issues of Strength of Materials (stress and strain states, the Hook's law, geometrical properties of an area, bending, shearing, torsion, deflection lines of beams, buckling and yielding criteria).