Filtry
wszystkich: 5098
wybranych: 3671
-
Katalog
- Publikacje 3671 wyników po odfiltrowaniu
- Czasopisma 242 wyników po odfiltrowaniu
- Konferencje 26 wyników po odfiltrowaniu
- Wydawnictwa 1 wyników po odfiltrowaniu
- Osoby 130 wyników po odfiltrowaniu
- Wynalazki 1 wyników po odfiltrowaniu
- Projekty 13 wyników po odfiltrowaniu
- Kursy Online 90 wyników po odfiltrowaniu
- Wydarzenia 10 wyników po odfiltrowaniu
- Dane Badawcze 914 wyników po odfiltrowaniu
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: CRANK BEARING
-
Application of acoustic emission for detection of fatigue microdemage in main and crank bearings for diesel engines
PublikacjaThe article presents reasons for applying the acoustic emission (AE) to detect fatigue microdamage in main bearings and crank bearings of ship main engines. Problem of determination of the fatigue life for slide bearing bushes was characterized in general. There were demonstrated properties of the objects of research, which were bushings made of the MB58 alloy, as well as an overall description of the research. It was shown that...
-
The use of Acoustic Emission to identification damages bearings the main and crank engines about the automatic ignition
PublikacjaThe article describes the laboratory tests, which make the first stage of the study concerning the use of the AE method to determine the technical state of the slide bearings in engines with self-ignition. The aim of the present tests was to compare the recorded signals in relation to the technical state of the material of the bearing bush and to check the possibility of using the AE method in determining the transition moment...
-
POSSIBILITY OF ASSESSMENT OF OPERATION OF SLIDING BEARINGS IN PISTON-CRANK MECHANISMS OF DIESEL ENGINES WITH REGARD TO LOAD AND TIME OF CORRECT WORK OF THE BEARINGS BY APPLYING ACOUSTIC EMISSION AS A DIAGNOSTIC SIGNAL
PublikacjaAbstract: The paper presents a possibility of determining (assessing) operation of sliding bearings with multilayer bushings in crank-piston mechanisms of diesel engines. Properties of load and wear, particularly fatigue and abrasive, are characterized in general. Acoustic emission as a diagnostic signal was proved to be useful for detection of the wear of sliding and barrier layers. Results of measurements of acoustic emission...
-
The crack surface morphology investigation of S355J2 steel after bending-torsion fatigue
Publikacja -
Influence of Bearing Bush Geometry on Properties of Water Lubricated Marine Main Shaft Bearings
PublikacjaW pracy przedstawiono wpływ geometrii smarowanego wodą, okrętowego łożyska ślizgowego wału głównego na jego własności hydrodynamiczne.Wykazano, że wielkość luzu łożyskowego, położenie oraz liczba rowków smarnych mają znaczący wpływ na nośnosć łożyska.
-
The energy approach to fatigue crack growth of S355 steel welded specimens subjected to bending
PublikacjaThe study presents the results of the research on the rate of fatigue crack growth subjected to bending in the ferritic-pearlitic structure. The studies were carried out at a constant amplitude of the moment and at various values of the load ratios R and at the operating frequency of the machine of 28.4 Hz. Flat specimens made of S355 steel and with fillet welds and with double-sided blunt external notches as well as concave...
-
ANALYSIS OF BEARING CLEARANCE AND WIDTH OF OIL GROOVE ON CHARACTERISTIC OF FLUID FILM IN HYDRODYNAMIC MAIN CRANKSHAFT BEARINGS
PublikacjaAbstract Paper represents analysis of influence of oil groove width and bearing clearance on characteristics of oil film in hydrodynamic journal main crankshaft bearing. Analysis was performed in purpose to define influence of bearing clearance and dimensions of oil groove on static characteristics and manufacturability of half shelf bearings in industrial high-volume production. Computer simulations was made using ARTbear program...
-
The influence of polymer bearing material and lubricating grooves layout on wear of journal bearings lubricated with contaminated water
PublikacjaThe goal of the present paper is to investigate wear properties of journal sliding bearing operating in the conditions of contaminated water lubrication. Several bearing materials and bearing sleeve designs (differing in the axial grooves position and their shape) were tested experimentally under typical operating conditions in a dedicated test rig, which was equipped with a lubricating system, enabling lubrication with contaminated...
-
Improvement of Thrust Bearing Calculation Considering the Convectional Heating within the Space between the Pads
PublikacjaA modern thrust bearing tool is used to estimate the behavior of tilting pad thrust bearings not only in the oil film between pad and rotating collar, but also in the space between the pads. The oil flow in the space significantly influences the oil film inlet temperature and the heating of pad and collar. For that reason, it is necessary to define an oil mixing model for the space between the pads. In the bearing tool, the solutions...
-
Improvement of the thrust bearing calculation considering the convectional heating within the space between the pads
PublikacjaA modern thrust bearing calculation tool should consider not only the oil film between pad and rotating collar but also the space between the pads. The oil flow in the space has a significant influence on the oil film inlet temperature, the convectional cooling of pad and collar and should be included in the bearing calculation methods. The authors use a tool developed at Clausthal University of Technology in cooperation with the...
-
The ring propeller with conical electromagnetic bearings and magneto fluid sealing system.
PublikacjaW przedstawionej koncepcji nowego zespołu napędowego najbardziej znamiennym rozwiązaniem jest zastosowanie nowoczesnych łożysk elektromagnetycznych dla pędnika śrubowego w prototypowej wersji silnika pierścieniowego synchronicznego z magnesami z ziem rzadkich. W artykule przedstawiono konstrukcję stożkowych łożysk magnetycznych. Technika uszczelniania cieczami magnetycznymi jest nową koncepcją pozwalającą na rozwiązywanie wielu...
-
Kinematic analysis of crank -cam mechanism of process equipment
Publikacja -
Fractographic-fractal dimension correlation with crack initiation and fatigue life for notched aluminium alloys under bending load
PublikacjaIn this study, fatigue fracture surfaces of aluminium alloy 2017-T4 notched specimens were investigated under cyclic bending to find an alternative failure loading index.. The surface topographies were measured on the entire fracture area with an optical profilometer for different loading conditions. Fatigue crack initiation life Ni and total fatigue life Nf were examined using standard surface topography parameters (such as, root...
-
IDENTIFICATION OF THE INTERFECE OF LATERAL SLIDE BEARINGS
PublikacjaIn the paper, the model of slide bearings of motor engine, the metodology of research on this type of bearings and its results are presented measurement standpoint consisting of main elements of Briggs & Stratton 550 serie 10 T 802 model piston motor engine driven by three phase elektric engine is introduced . On the measurement standpoint are measurements were done, needed for specification...
-
ATTEMPT AT EVALUATING THE INFLUENCE OF BENDING STRESS ON SHAFT WEAR PROCESSES IN WATER LUBRICATED SLIDING BEARING WITH A RUBBER BUSHING
PublikacjaWater lubricated bearings find increasingly wide application in shipbuilding or hydro–power industry, the popularity stemming from their numerous advantages. Unfortunately, as it turns out, water lubricated bearings do not always meet expectations, as on occasion they become subject to intense, premature wear which requires costly repair. One of the still unexplained phenomena is the process of excessive bearing wear, in particular...
-
Shipyard Crane Modeling Methods
Publikacja -
Crack monitoring in concrete beams under bending using ultrasonic waves and coda wave interferometry: the effect of excitation frequency on coda
PublikacjaConcrete is one of the most widely used construction materials in the world. In recent years, various non-destructive testing (NDT) and structural health monitoring (SHM) techniques have been investigated to improve the safety and control of the current condition of concrete structures. This study focuses on micro-crack monitoring in concrete beams. The experimental analysis was carried out on concrete elements subjected to three-point...
-
Rank Coloring of Graphs.
PublikacjaRozdział jest poświęcony uporządkowanemu kolorowaniu grafów. Przedstawiono jego podstawowe własności oraz zastosowania praktyczne.
-
EVALUATING THE INFLUENCE OF BENDING STRESS ON A 1H18N9 STEEL SHAFT WEAR PROCESS IN A WATER LUBRICATED SLIDING BEARING WITH A RUBBER BUSHING
PublikacjaThe issue of excessive wear of shaft journals co-working with a rubber bearing has been unexplained so far. Premature and sometimes very intensive wear of ship sliding bearings in water conditions is the reason for carry out very expensive and more frequent than expected repairs. The authors (E. Piątkowska, W. Litwin) made an attempt to find a case that influences the value of this wear described in the paper “Attempt at Evaluating...
-
THE APPLICATION OF KALMAN FILTERING TO PREDICT VERTICAL RAIL AXIS DISPLACEMENTS OF THE OVERHEAD CRANE BEING A COMPONENT OF SEAPORT TRANSPORT STRUCTURE
PublikacjaAs the devices designed to transport materials, the overhead cranes should meet certain geometric requirements for their operation to be safe. The presently available geodetic equipment, in particular total stations, provides opportunities for precise 3D measurements of coordinates of the controlled points. These coordinates make a basis for correcting the height of crane runway axes. The paper presents a method to calculate position...
-
The correlation of fractal dimension to fracture surface slope for fatigue crack initiation analysis under bending-torsion loading in high-strength steels
PublikacjaIn this study, the fractal dimension of fatigue fracture surfaces is investigated in order to find an alternative failure loading indicator. Some of many metrological factors are generalized by reducing the fracture surface structure to one factor and develop an entire fracture surface procedure by analyzing the impact of surface slope and calculation resolution. Three notched geometries are studied under cyclic bending-torsion:...
-
Formation and Growth of the Crack in Bonded Joints Under Mode I Fracture: Substrate Deflection at Crack Vicinity
PublikacjaAdhesive bonding is now commonly used in aircraft, cars, boats, etc. In these applications, thin panels are often bonded. In such thin structures, heterogeneous mechanical loading along the bondline edge (or potential crack front), is likely to arise due to 3D structural effects. The crack front and its vicinity is a special region, in that it is where structural properties of the adherend material meet those of the adhesive (discontinuity)....
-
On the crack front curvature in bonded joints
PublikacjaStandard tests of adhesively bonded specimens are likely to produce heterogeneous stress distribution along the crack front and its vicinity. High separation rate mode I dominated fracture test is performed.Observation of post mortem fractured surfaces with an optical microscope reveals characteristic features of mixed mode I/III fracture near the sides of the specimen but not in the middle. At first, finite elements calculations...
-
Crank–Nicolson FDTD Method in Media Described by Time-Fractional Constitutive Relations
PublikacjaIn this contribution, we present the Crank-Nicolson finite-difference time-domain (CN-FDTD) method, implemented for simulations of wave propagation in media described by time-fractional (TF) constitutive relations. That is, the considered constitutive relations involve fractional-order (FO) derivatives based on the Grünwald-Letnikov definition, allowing for description of hereditary properties and memory effects of media and processes....
-
Experimental investigation and process parameter optimization of sheet metal bending by line heating method
PublikacjaThe present study is concerned with the experimental investigation of sheet metal deforming by line heating method that incorporates the combined effect of traverse speed of the torch, thickness of the sheet metal, and the number of passes of the torch. For the numerical analysis of metal bending by line heating, the
-
Wave propagation in plate structures for crack detection
Publikacja -
Crack identification in cantilever beam using wavelets
PublikacjaPrzedstawiono metodę identyfikacji zniszczeń przy użyciu transformacji falkowej. Rozpatrzono przykład belki wspornikowej. Pokazano, że transformacja falkowa wykrywa miejsce zniszczenia.
-
Wave propagation in plate structures for crack detection.
PublikacjaW pracy przedstawiono analizę propagacji fali poprzecznej w płycie z pęknięciem. Do modelowania zagadnienia zastosowano metodę elementów spektralnych.
-
Hertzian Crack Propagation in Ceramic Rolling Elements
PublikacjaThe properties of ceramics are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such crack are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations are based on a three dimensional model for the ring crack propagation. The stress intensity factors along crack...
-
Propagation of in-plane waves in an isotropic panel with a crack
PublikacjaW pracy przedstawiono model tarczowego elementu spektralnego do analizy propagacji fali wzdłuznej w panelach z uszkodzeniami.
-
Crack propoagation in MgO-PSZ ceramic materials
PublikacjaThe properties of ceramic materials such as elevated hardness, high temperature capability, low coefficient of thermal expansion are of interest for rolling element materials. Widely used ceramic materials in engineering applications are silicon nitride, zirconia and alumina. The paper presents an experimental study of the fatigue life of MgO-PSZ ceramic material in lubricated contact with defined types of cracks. A ceramic angular...
-
Numerical analysis of crack propagation in silicone nitride
PublikacjaThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculation...
-
Bearing capacity for random subsoil.
PublikacjaW pracy zaproponowano modyfikację metody charakterystyk bazującej na stochastycznej metodzie różnic skończonych. Podejście takie pozwoliło na uwzględnienie przestrzennej zmienności podłoża gruntowego przy ocenie nośności granicznej ławy fundamentowej posadowionej na losowym podłożu. Przeprowadzono analizę wpływu dyskretyzacji ośrodka gruntowego na rozwiązanie oraz rozpatrzono jego zbieżności.
-
POSSIBILITY OF IDENTIFICATION OF TECHNICAL CONDITION OF BEARINGS FOR SELF-IGNITION ENGINES BY APPLICATION OF ACOUSTIC EMISSION AS A DIAGNOSTIC SIGNAL
PublikacjaThis paper presents the results of empirical studies where the acoustic emission (AE) method was applied to identify the technical condition of sliding surfaces of main and crank bearings for main diesel engines. The test results indicate that the measurements of the AE parameters allow the technical condition identification for bearings of this type. The results refer to the measurements of the parameters for AE generated in the...
-
Study of Bioreductive Anticancer Agent RH-1-Induced Signals Leading the Wild-Type p53-Bearing Lung Cancer A549 Cells to Apoptosis
Publikacja -
Remote learning among students with and without reading difficulties during the initial stages of the COVID-19 pandemic
PublikacjaThis article presents the results of a survey on yet under-researched aspects of remote learning and learning difficulties in higher education during the initial stage (March – June 2020) of the COVID-19 pandemic. A total of 2182 students from University of Warsaw in Poland completed a two-part questionnaire regarding academic achievements in the academic year 2019/2020, living conditions and stress related to learning and pandemic,...
-
Experimental research on a hydrodynamic thrust bearing with hydrostatic lift pockets: Influence of lubrication modes on bearing performance
PublikacjaThe aim of the study is to investigate the performance of a thrust bearing equipped with hydrostatic lift pockets under different lubrication modes. Three types of flat land bearing lubrication modes are studied experimentally: hydrostatic lubrication (HS; forced oil injection to the pockets), hybrid lubrication (HS + HD; hydrostatic lubrication combined with the external forced bearing oil supply) and hydrodynamic lubrication...
-
Crack identification using wavelets on experimental staticdeflection profiles
PublikacjaArtykuł prezentuje metodę lokalizacji uszkodzeń w belce wspornikowej za pomocą transformaty falkowej statycznej linii ugięcia. Efektywnośc proponowanej techniki jest sprawdzona na podstawie badań eksperymentalnych. Do pomiaru statycznej linii ugięcia proponuje się metodę fotogrametryczną.
-
Genetic algorithm for fatique crack detection in Timoshenko beam.
PublikacjaW pracy przedstawiono metodę detekcji peknięć zmęczeniowych w początkowej fazie ich rozwoju. Algorytm detekcji wykorzystuje metodę algorytmów genetycznych połączoną z metodą gradientową. Funkcja celu oparta została o zmiany w propagujacej fali sprężystej.
-
Numerical assessment of the fatigue crack propagation in ship structuraldetails.
PublikacjaPrzedstawiono podejście teoretyczne pozwalające na modelowanie rozwoju pęknięcia w konstrukcji kadłuba okrętu. Omówiono założenia i procedurę realizacyjną. Pokazano wyniki badań rzeczywistych modeli konstrukcji kadłuba-skrzyżowanie wiązań ramowych o jednakowej wysokości. Dokonano porównania i krytycznej analizy wyników uzyskanych na drodze teoretycznej z wynikami badań rzeczywistych.
-
Design of modified PID controllers for 3D crane control
PublikacjaFrom the control viewpoint, 3D crane is a dynamic, nonlinear and multidimensional electromechanical system. In this paper, five control systems using a set-point weighted PID controllers (modified controllers) are designed. These structures and properties are presented. Optimization process of controllers settings based on integral performance indices is made. Simulation tests of control systems are presented. Comparison of integral...
-
On stress singularity near the tip of a crack with surface stresses
PublikacjaIn the framework of the simplified linear Gurtin–Murdoch surface elasticity we discuss a singularity of stresses and displacements in the vicinity of a mode III crack. We show that inhomogeneity in surface elastic properties may significantly affect the solution and to change the order of singularity. We also demonstrate that implicitly or explicitly assumed symmetry of the problem may also lead to changes in solutions. Considering...
-
Crack Resistance of Asphalt Concrete Subjected to Environmental Factors
PublikacjaThe paper presents an analysis of the influence of environmental factors on the cracking susceptibility of asphalt concrete resulting in a change in the durability of asphalt pavement. In order to assess the phenomenon, laboratory tests were carried out taking into account the destructive effects of moisture, freeze-thaw cycle and long-term ageing. The influence of both factors occurring simultaneously was also verified. Due to...
-
Experimental verification of MWO bearing machine
PublikacjaPrzedstawiono wyniki weryfikacji doświadczalnej nowego stanowiska przeznaczonego do badań wytrzymałości zmęczeniowej warstwy powierzchniowej łożysk ślizgowych. Badano dwu- i trójwarstwowe cienkościenne panwie ślizgowe. Warstwa nośna wykonana była ze stopu CuPb30. W wariancie trójwarstwowym występowała powłoka ze stopu PbSnCu. Przedstawiono przykłady zaobserwowanych pęknięć zmęczeniowych. Maszyna MWO okazała się w pełni przydatna...
-
Virtual hearing aid - multimedia tool for demonstrating hearing aid benefits
PublikacjaWiększość osób niedosłyszących nie jest świadoma wszystkich możliwości korekcji ubytku słuchu. Wykorzystując techniki multimedialne można stworzyć oprogramowanie, które znacznie ułatwi i przybliży proces dopasowania aparatów słuchowych. Celem przeprowadzonych eksperymentów było opracowanie multimedialnego systemu, który pozwala zrealizować następujące funkcje: - pomiar charakterystyki dynamiki słuchu, - wyznaczanie charakterystyki...
-
Longitudinal wave propagation. Part II—Analysis of crack influence
Publikacja -
Longitudinal wave propagation. Part II, Analysis of crack influence
PublikacjaW pracy analizowano wpływ pęknięć zmęczeniowych na propagacje fali wzdłużnej w prętach. Opracowano nowe typy element ów spektralnych oparte na teorii elementarnej, Love'a, Mindlina i trójpostaciowej.
-
New Method for Determination of Adjustment Corrections for Crane Rail Axes
PublikacjaElectronic tacheometers are currently a standard instrument used in geodetic work, including also geodetic engineering measurements. One of the many applications of tacheometers in engineering geodesy are 3D control measurements of crane rail axes. This paper proposes a new method of computing adjustment corrections for crane rail axes based on 3D polar measurements performed with an electronic tacheometer. The intermediary method...
-
Crack identification using wavelets on experimental static deflection profiles
Publikacja -
A New Geodetic Method of Examination of Geometrical Conditions of a Crane Bridge
PublikacjaSafety is one of the key aspects related to crane-based material transport. In order to ensure safe crane operation and material transport, it is necessary to meet certain geometrical conditions. The authors addressed the geometrical conditions of a crane bridge, a substantial crane component. The paper presents the method to compute displacement components of points on the top of a bridge crane relative to their design position....