Wyszukiwarka
Filtry
wszystkich: 1322
wybranych: 1132
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: 18NI300 STEEL
-
Wet H2S corrosion and degradation of pipeline in amine regeneration system
PublikacjaThe paper presents the results of NDT examinations, metallographic tests and risk assessment of degradation related to corrosion of amine regeneration unit in a desulphurisation system. Intensive corrosion resulting from acid gases environment upon water condensation causes perforation of the pipeline. Detailed analysis reveals cracking related to the mechanism of wet H2S. Hydrogen penetration, resulting from the wet H2S process,...
-
Implementacja pomierzonych imperfekcji geometrycznych powłokicylindrycznej do modelu obliczeniowego
PublikacjaThis paper presents the method of implementation of the geometrical imperfections used by the author during the experimental and numerical research into the load-carrying capacity of cylindrical steel shells subjected to uniform circumferential compression.
-
Badania spawalności stali S460N w środowisku wodnym z wykorzystaniem próby Tekken
PublikacjaSpawanie w środowisku wodnym niesie ze sobą wiele problemów, wśród których najważniejszym jest skłonność stali do powstawania pęknięć zimnych. O ile w przypadku spawania na powietrzu istnieje wiele metod zapobiegania tym pęknięciom, o tyle pod wodą zastosowanie tych metod jest ograniczone. Z tego powodu konieczne jest określenie skłonności danego materiału do pękania zimnego. W pracy oceniono spawalność drobnoziarnistej...
-
Wnikanie wodoru z paliwa i oleju do stali stopowych 26h2mf i 34hnm oraz jego oddziaływanie z defektami struktury = The hydrogen entry from fuel and oil to the 26h2mf and 34hnm alloy steels, and its interaction with structure defects
PublikacjaWykonano badania skłonności do korozji naprężeniowej przy rozciąganiu próbek ze stałą małą prędkością 10-6s-1, przy obciążeniu cyklicznie zmiennym w środowisku gorącego paliwa kotłowego i gliceryny oraz badania absorpcji wodoru dla stali stopowych 26H2MF i 34HNM w paliwie kotłowym, przepracowanym oleju mineralnym oraz glicerynie jako środowisku referencyjnym. Wykazano największą wrażliwość stali przy obciążeniach zmiennych oraz...
-
Alternative way of the main reinforcement anchorage in reinforced short cantilevers
PublikacjaThe results of the experimental investigation of the reinforced corbels and dapped end beams with steel studs were introduced in the work. The efficiency of this type of the reinforcement was compared with the typical reinforcenet applied in reinforced conctrete construcions.
-
Time Domain Modeling of Propeller Forces due to Ventilation in Static and Dynamic Conditions
Publikacja -
Investigation and operation problems of metal tanks in Poland
PublikacjaThe paper consists of three parts concerned with steel cylindrical, vertical tank for liquid fuel. In the first part the present trends in tank design and building in Poland are described. The main are: · reduction of environment contamination danger caused by tank leakage and hydrocarbons evaporation, · increasing capacity of new tanks (100000 m3 and more) due to economic factor - reduction of steel amount per m3 of storage capacity....
-
Protective and Suppressing Electromagnetic Interference Properties of Epoxy Coatings Containing Nano-Sized NiZn Ferrites
PublikacjaNano-crystalline ferrites with the chemical formula NixZn(1−x)Fe2O4, where x = 0, 0.2, 0.4, 0.6, 0.8, 1.0, were synthesized using a co-precipitation method. The obtained ferrites were investigated by X-ray diffraction (XRD). The corrosion inhibiting behavior of nano-sized ferrites was tested using carbon steel samples and 10% aqueous ferrite extracts. Results were compared with previous data obtained for micro-sized ceramic ferrites....
-
TRUSS JOINT WITH POSITIVE ECCENTRICITY EXPERIMENTAL RESEARCH
PublikacjaDue to the technological reasons in modern lightweight steel trusses, fabricated from cold- formed sections, positive eccentricities appear in the truss nodes what induce additional forces in the truss chords. To account for the real load-carrying capacity of truss node area the steel structure research in scale 1:1 were conducted. The experiments consisted of two parts: preliminary and proper one, when conclusions from...
-
Wybrane aspekty modelowania uderzenia pojazdem dźwigara wiaduktu
PublikacjaW pracy przedstawiono różne zagadnienia związane z uderzeniem pojazdu w dźwigar wiaduktu. Omówiono wybór modelu obliczeniowego, na podstawie porównania wyników dla modelu dźwigara zespolonego, modelu dźwigara stalowego oraz modelu wiaduktu. Następnie opisano model dźwigara zespolonego zastosowany w analizie MES oraz metodę wyznaczania współczynników tłumienia Rayleigha. Symulację numeryczną uderzenia dźwigara wiaduktu przez koparkę...
-
PRĄDY WYRÓWNAWCZE W UZIOMACH FUNDAMENTOWYCH I SZTUCZNYCH
PublikacjaW artykule omówiono zasady wykonywania uziomów fundamentowych i sztucznych. Przedstawiono wyniki pomiarów prądów w instalacji zawierającej stal zbrojeniową w fundamencie, połączoną z układem uziomu sztucznego w ziemi wykonanym z stali ocynkowanej.
-
Investigation of behaviour of metal structures with polymer dampers under dynamic loads
PublikacjaA large number of accidents concerning structures subjected to dynamic loads have been recently observed. One of the examples of such a structure is a temporary steel grandstand erected using scaffolding system. Dynamic load that is generated by crowd movement has a significant influence on the behaviour of the structure and may lead to excessive structural vibrations. The aim of the study is to consider the idea of using polymer...
-
Corrosion monitoring by harmonic analysis in aqueous environments
PublikacjaThis paper presents tests concerning the rate of corrosion in non-alloy steel (type S235JR) in an aqueous environment, with an additive of sodium chloride by means of polarization resistance measurements and harmonic analysis. The tests have been carried out for steel samples exposed to the testing environment for six weeks, in order to obtain a constant rate of corrosion in the function of time. The measurements have aimed at...
-
On the correlation between magnetoacoustic emission and magnetostriction dependence on the applied magnetic field
PublikacjaThe correlation between magnetoacoustic emission signal envelopes and magnetostriction curves is investigated. Two sets of samples are being considered: tempered martensitic steel and plastically deformed ferritic steel. It is shown that even though some general relations may be observed, as was demonstrated in the literature, the correlation is not always present. One may not expect to change both quantities in the same way if...
-
Tribological Properties of Thermoplastic Materials Formed by 3D Printing by FDM Process
PublikacjaThe dataset entitled 3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_4 contains: the time base (expressed in seconds and minutes), the friction torque for sliding friction, rotational velocity of the counter – specimen (velocity of sliding), friction coefficient, load in the friction contact...
-
INFLUENCE OF SOLID PARTICLE CONTAMINATION ON THE WEAR PROCESS IN WATER LUBRICATED MARINE STRUT BEARINGS WITH NBR AND PTFE BUSHES
PublikacjaThis paper reports on a study of the influence of solid particle contamination on the wear process in water-lubricated slide bearings (steel-acrylonitrile-butadiene rubber (NBR) and steel- polytetrafluoroethylene (PTFE)). To compare the wear of the shaft journal and bushes (NBR and PTFE) when lubricated with fresh water and contaminated water, an experiment was carried out to identify key factors that influence the state of wear...
-
Mechanical Performance and Environmental Assessment of Sustainable Concrete Reinforced with Recycled End-of-Life Tyre Fibres
PublikacjaThe presented research’s main objective was to develop the solution to the global problem of using steel waste obtained during rubber recovery during the tire recycling. A detailed comparative analysis of mechanical and physical features of the concrete composite with the addition of recycled steel fibres (RSF) in relation to the steel fibre concrete commonly used for industrial floors was conducted. A study was carried out using...
-
Corrosion behavior of concrete produced with diatomite and zeolite exposed to chlorides
PublikacjaChloride induced reinforcement corrosion is widely accepted to be the most frequent mechanism causing premature degradation of reinforced concrete structures. The electrochemical impedance of reinforcing steel in diatomite- and zeolite-containing concrete exposed to sodium chloride was assessed. Chemical, physical and mineralogical properties of three concrete samples (20% diatomite, 20% zeolite, and a reference containing neither)...
-
Surface Texture after Turning for Various Workpiece Rigidities
PublikacjaIn the paper, we present an analysis of the surface texture of turned parts with L/D (length/diameter) ratios of 6 and 12 and various rigidity values. The studies were carried out on samples made of S355JR steel and AISI 304 stainless steel. A detailed analysis of 2D surface profiles was carried out by using a large number of parameters that allowed us to distinguish significant differences in the surface microgeometry, which confirmed...
-
Numerical and Experimental Study of Propeller Ventilation
Publikacja -
Numerical and Experimental Study of Propeller Ventilation
Publikacja -
Ship’s de-perming process using coils lying on seabed
PublikacjaA ship built from ferromagnetic steel disturbs the uniformity of the Earth’s magnetic field. Changes of ship’s signature are due to the magneto-mechanical interaction of the hull with the Earth’s magnetic field. The ship’s magnetic field can be detected by a magnetic naval mine. For this reason, the vessel has to be demagnetized. There are several methods of ship’s de-perming. The results of experimental and computer simulations...
-
Reference-free determination of debonding length in reinforced concrete beams using guided wave propagation
PublikacjaThis paper presents theoretical and experimental investigations of guided wave propagation in reinforced concrete beams, with pre-existing debonding between steel rebars and concrete blocks, for the purpose of damage detection. The primary aim of these investigations was a detailed analysis of the possible applications of wave propagation in single and multiple debonding detection in reinforced concrete structures and reference-free...
-
Numerical investigation of the core eccentricity effect on wave propagation in embedded waveguide
PublikacjaThe paper presents results of theoretical and numerical investigation of guided wave propagation in two-layer bars with geometric imperfections in the form of eccentric location of steel core. Steel rod of diameter equal to 1 cm embedded in composite mortar-type cover with external diameter equal to 5 cm has been taken into consideration. Several different rods with variable size of eccentricity are analysed. Results for rods with...
-
INFLUENCE OF TACK WELDS DISTRIBUTION AND WELDING SEQUENCE ON THE ANGULAR DISTORTION OF TIG WELDED JOINT
PublikacjaIn this paper the influence of tack welds distribution and welding sequence on angular distortion of the Tungsten Inert Gas (TIG) welded joint was tested. Additionally, the effect of welding current on angular distortion was assessed. For research X2CrTiNb18 (AISI 441) stainless steel (2.5 mm thick) was chosen. During research specimens were prepared with different distributionsof tack...
-
Effect of electrode waterproof coating on quality of underwater wet welded joints
PublikacjaIn this paper, the effects of different hydrophobic coatings on the surface of covered electrodes on the quality of wet welded carbon steel joints were discussed. Commonly available hydrophobic substances used in industrial applications were selected for the research. The aim of using waterproof coatings was to check the possibility to decreasing the susceptibility of highstrength low-alloy S460N steel to cold cracking. During...
-
Building damage due to structural pounding during earthquakes
PublikacjaEarthquake-induced pounding between adjacent buildings has been identified as one of the reasons for substantial damage or even total collapse of colliding structures. A major reason leading to interactions in buildings results from the differences in their dynamic parameters and also from insufficient distance between the structures. Although the research on structural pounding has been much advanced, the studies have mainly been...
-
Repeated Projectile Impact Tests on Multi-Layered FibrousCementitious Composites
PublikacjaThis research aims to experimentally evaluate the behaviour of multi-layered fibrous cementitious composites withintermediate Glass Fibre Meshes (GFM) under repeated projectile load. The impact load was subjected through a convexedge projectile needle at a low velocity on cylindrical specimens of three-layered fibrous cementitious composites, whichhave two different steel fibre distributions. In series A mixtures, a constant steel...
-
Ground anchors diagnostic process based on elastic wave propagation method
PublikacjaThe paper is focused on analysis of elastic wave propagation in the context of diagnostics of ground anchors. Numerical simulations were performed to assess the possibility of evaluation of the anchorage quality. It was assumed that the quality and the load capacity of the anchor system directly depend on the length, on which mortar and steel cooperate.
-
Buckling Analysis of Cold Formed Silo Column
PublikacjaThe paper is devoted to stability analysis of different models of steel cold formed silo column. The steel cylindrical silos are often composed of corrugated walls and vertical open-sectional columns uniformly placed along the silo circumference. Both the whole 3D silo, a simplified model consisting of one column with a part of the silo walls, and a single column resting on elastic foundation provided by the silo walls were analyzed....
-
The Influence of Selected Parameters of Numerical Modelling on Strains and Stresses at Weld Toe Notch
PublikacjaLatest development in the field of welding technology and prefabrication enabled massive production of thin-walled sandwich structures. Multi-layered sandwich structures are fabricated with the use of high-power CO2 lasers, friction welding, arc welding, hybrid welding, or other technique designed for the special purpose. Steel or aluminium alloy plates with thickness between 1 and 5 mm are connected by internal stiffeners. Strength...
-
Manganese Phosphatizing Coatings: The Effects of Preparation Conditions on Surface Properties
PublikacjaManganese phosphate coating could be used to protect the surface of steel products. However, it is essential to determine the effects which process parameters, as well as the types of additives used, have on the efficiency of coating deposition. Thus, we present here a process of phosphatization of low-alloy steel (for 15 min at 95 ◦C) in manganese/nickel baths followed by a passivation process with the use of a silicon and zircon...
-
Novel application of dynamic electrochemical impedance monitoring to a cataphoretic coating process
PublikacjaThe paper presents a novel method of on-line impedance monitoring of cataphoretic coating application process. Utilization of dynamic electrochemical impedance spectroscopy (DEIS) overcame the fundamental problem connected with non-stationarity of the aforementioned coating deposition process, which eliminates classical impedance spectroscopy technique from a real-time description of cataphoresis. The paper illustrates selected examples...
-
Burnout Investigation of Small Diameter Tubes Immersed in Nanofluids
PublikacjaThis paper deals with research into pool boiling critical heat flux (CHF) of water–Al2O3, water–TiO2 and water–Cu nanofluids on horizontal stainless steel tubes. The experiments were conducted under atmospheric pressure. Nanoparticles were tested at concentrations of 0.001%, 0.01%, 0.1% and 1% by weight. Ultrasonic vibration was used in order to stabilize the dispersion of the nanoparticles. Although dispersants were not used to...
-
Influence of the Widespread Use of Corten Plate on the Acoustics of the European Solidarity Centre Building in Gdansk
PublikacjaThis paper describes the relationship between a strong architectural vision that is difficult to balance, and user expectations in terms of acoustics. The focus is on the use of corten steel as the dominant finishing material on façades and interiors to achieve an expressive, symbolic message through program-based design. The architectural premises justifying the adopted solutions are presented, especially the universality and...
-
Risks caused by microbiologically influenced corrosion in diesel fuel storage tanks
PublikacjaMicrobiologically influenced corrosion (MIC) poses serious problems for the petrochemical and refinery industries. Particularly favourable conditions for MIC arise in storage tanks and transmission pipelines for mixtures of diesel oil with the addition of a biocomponent (in Poland 7%). The best conditions for the development of MIC occur at the fuel-water interface, where microorganisms are provided with a source of food and water,...
-
Ocena stanu technicznego rurociągu przesyłowego zawiesiny popiołów w Elektrowni Ostrołęka B
PublikacjaPrzedmiotem pracy był rurociąg przesyłowy zawiesiny popiołów przesyłanych z Elektrowni Ostrołęka B. Celem pracy było potwierdzenie przynależności próbek yvyciętych z rurociągu do określonego gatunku stali i ocena stanu materiału po eksploatacji. Dla zrealizowania tego celu wykonano: - analizę składu chemicznego materiału pobranego ze stalowych rur, - mikroanalizę warstw wierzchnich na powierzchni wewnętrznej i zewnętrznej, -...
-
Carbon dioxide sequestration by industrial wastes through mineral carbonation: Current status and perspectives
PublikacjaMineral carbonation using natural minerals or industrial wastes is a safe and promising strategy for CO2 sequestration. Application of industrial wastes for this purpose has significant ecological and environmental value, which is one of the key green technologies in the global carbon mitigation. This review summarizes the current research status of CO2 mineralization by industrial wastes. This work surveys the mechanisms and capacities...
-
Badania nośności na zginanie innowacyjnego kształtownika giętego na zimno typu GEB
PublikacjaLekkie konstrukcje metalowe wytwarzane z kształtowników giętych na zimno to jedna z najszybciej rozwijających się dyscyplin w zakresie budownictwa. Do niedawna profile gięte na zimno stosowano wyłącznie jako elementy drugorzędne, czyli płatwie oraz rygle. Nowo opatentowany przekrój typu GEB ma być wykorzystywany jako element nośny konstrukcji ramowych. Jednak jego zaistnienie na rynku budowlanych konstrukcji metalowych jest uwarunkowane...
-
Standard and modified falling mass impact tests on preplaced aggregatefibrous concrete and slurry infiltrated fibrous concrete
PublikacjaAlthough several studies have been conducted to evaluate the impact response of concrete using theAmerican Concrete Institute (ACI) 544-2R falling mass impact test, the variations in test results are themain drawback of this testing method. This study aims to reduce the variations in experimental impacttest results by introducing two simple test setup modifications; (1) using coarse or fine aggregate bed-ding as an alternative...
-
Evaluation of reformer tubes degradation after long term operation
PublikacjaPurpose of this paper is to show the effect of long-term service at elevated temperatures on microstructural changes of cast steel reformer tubes made of the alloy IN-519 (24%Cr, 24%Ni, Nb). The relationship between mechanical properties and microstructure degradation is discussed. Investigations were performed on five tubes taken from ammonia reformer furnace. Tubes worked at temperature of 880C and 3,2 MPa pressure. The operation...
-
Influence of permanent magnetic field on wear performance of dry sliding contacts
PublikacjaResults of experimental studies concerning the influence of permanent magnetic field on wear of dry sliding contact are presented.It was found that magnetic field of horizontal orientation is causing temporary reduction of material's hardness. It also facilitates and accelerates removal process of wear particles from the contact zone.Formation of bulges, consisting of accumulated and compacted anti-ferromagnetic material produced...
-
The Influence of Modelling Material Zones on Strains and Stresses at Weld Toe Notch
PublikacjaThe latest development in the field of welding technology enabled prefabrication of thin-walled sandwich structures in an industrial scale. Sandwich structures fabricated of steel, or aluminium alloy plates and stiffeners are welded with the use of hi-power CO2 lasers. Strength analysis of such structures with the use of finite element method needs proper material modelling.In this paper the material model of steel sandwich panel...
-
Debonding Detection in Reinforced Concrete Beams with the Use of Guided Wave Propagation
PublikacjaOne of the most frequent damage of the reinforced concrete structures is debonding between steel bar and concrete cover. In the case of debonding occurrence not only the strength of the structure decreases, but also it is more vulnerable to corrosion damages. For this reason fast and effective methods of debonding detection in an early stage of its development need a significant boost. The paper presents analytical and experimental...
-
Guided ultrasonic waves for detection of debonding in bars partially embedded in grout
PublikacjaThis paper deals with theoretical, numerical and experimental investigations of guided wave propagation in multilayered cylindrical bars with pre-existing debonding. The research focuses on a complex description of the nature of the wave phenomena occurring in a debonded specimen with a special emphasis on the influence of the location of damage on the wave conversion and diffraction. Experimental non-destructive and destructive...
-
Jumping Wave Characteristic during Low Plasticity Burnishing Process
PublikacjaDuring the low plasticity burnishing process of soft materials such as carbon steel with a hardness of up to 40 HRC (Rockwell grade) a raised structure of the material known as the Jumping Wave forms in front of the tool roll. This phenomenon significantly disturbs the burnishing process, but is very poorly described in the literature. This article presents studies of this phenomenon on the example of burnished 1.0562 steel. The...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaThis work presents preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter and 2000 mm length. Nanoparticles were tested at the concentrations of 0.01%, 0.1%, 1% and 5% by weight and the Reynolds number range encompasses laminar as well as turbulent flows.
-
Opracowanie ekspertyzy dotyczącej przyczyn pękania łopatek wirnika SP turbiny PG1 typu 13UP55
PublikacjaZakres badań i analiz dotyczył ustalenia przyczyn pękania elementów łopatek wirnika SPA5 turbiny TG1 typu 13UP55 obejmował: 1. wykonanie badań składu chemicznego stali, z której wykonano łopatki dostarczone przez Zleceniodawcę dwoma metodami, 2. badania mikroobszarów zniszczenia łopatek na mikroskopie elektronowym skaningowym z mikroanalizatorem EDS, 3. badania metalograficzne makroskopowe i mikroskopowe fragmentów...
-
Storing Matter’technique in SIMS depth profile analysis
PublikacjaSecondary ion mass spectrometry (SIMS) is a very useful technique for the analysis of layered systems. It is based on the primary ion beam sputtering of solids and mass analysis of the emitted secondary ions. A main limitation of this technique results from the direct quantitative analysis, since the ionization efficiency of a given atom is highly influenced by the neighbouring atoms at the surface. This phenomenon is known as...
-
Centrally Pivoted Tilting Pad Thrust Bearing with Carbon-Based Coated Collar—Experimental Results of Low- and Medium-Speed Operation
PublikacjaExperimental results of the research on a tilting pad thrust bearing with symmetrical pad support in the conditions of high loads and low speeds are presented in the paper. As described in the literature review, experimental results of tilting pad bearings at low speed/high load regime and transient conditions are rare. Unusual material selection - steel pad against a DLC-type coating on the collar was utilized. Such material combination...