Filtry
wszystkich: 3451
wybranych: 1421
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: container shipping
-
Thermal Biomass Conversion: A Review
PublikacjaIn this paper, the most important methods of thermal conversion of biomass, such as: hydrothermal carbonization (180–250 °C), torrefaction (200–300 °C), slow pyrolysis (carbonization) (300–450 °C), fast pyrolysis (500–800 °C), gasification (800–1000 °C), supercritical steam gasification, high temperature steam gasification (>1000 °C) and combustion, were gathered, compared and ranked according to increasing temperature. A comprehensive...
-
Biological and mechanical properties of bone cement with nanoarticles - in vitro and in vivo research
PublikacjaDespite antibiotic preventive treatment both before and after implant implementation, the risks of infection are real. These infections develop at the implant surface a few months after inserting them into the body. To prevent the development of bacteria and reduce the risk of infection, implants coated with nanoparticles are used. The Mechanical Department of the Technical University of Gdansk carries out research into using bone...
-
Nitrogen transformation during fermentation in agricultural biogas plants
PublikacjaThe aim of the present study was to determine changes in the organic nitrogen fraction in the liquid fraction of the digestate during laboratory tests of mono- and co-digestion. Three agricultural wastes were tested: distillery residue, cattle slurry and corn silage. In the mono-fermentation tests, the initial total nitrogen concentration depended on the feedstock used. As a result of the hydrolysis and ammonification of the organic...
-
Mineral Composition of Dietary Supplements-Analytical and Chemometric Approach
PublikacjaThere is a lack of data on the actual composition and effectiveness of beetroot-based dietary supplements. The research aimed to determine the profile of 22 elements (Na, K, Ca, Mg, P, Fe, As, Se, Zn, Cu, Ag, Co, Ni, Mo, Al, Mn, Sr, Cr, Ba, Li, Pb, Cd) in beetroot and its supplements by the microwave plasma atomic emission spectrometry (MP-AES) method. The analytical procedure was optimised and validated. The composition of both...
-
Degradation of tetracycline antibiotic utilizing light driven-activated oxone in the presence of g-C3N4/ZnFe LDH binary heterojunction nanocomposite
PublikacjaIn the present study, a binary heterojunction nanocomposite composed of graphitic carbon nitride (g-C3N4) and Zn/Fe-contained layered double hydroxide (ZnFe LDH) was employed as heterogeneous catalyst for the decomposition of tetracycline (TC) antibiotic utilizing Oxone and UV light irradiation. The sole use of g-C3N4/ZnFe LDH as adsorbent led to the negligible elimination of TC. In addition, the sole use of Oxone or UV (photolysis)...
-
Ultrasound assisted solvent extraction of porous membrane-packed samples followed by liquid chromatography-tandem mass spectrometry for determination of BADGE, BFDGE and their derivatives in packed vegetables
PublikacjaThe problem of the presence of trace organic pollutants in food is of growing importance due to increasing awareness about their impact on newborns, infants and adults of reproductive age. Despite the fact that packaged food products offer many advantages, packaging can be a source of contamination for stored food. Thus, monitoring such pollution in food is of high importance. In this work, a novel methodology based on the solvent...
-
Reduction of CO2 Emissions from Offshore Combined Cycle Diesel Engine-Steam Turbine Power Plant Powered by Alternative Fuels
PublikacjaDiverse forms of environmental pollution arise with the introduction of materials or energy that exert adverse effects on human health, climate patterns, ecosystems, and beyond. Rigorous emission regulations for gases resulting from fuel combustion are being enforced by the European Union and the International Maritime Organization (IMO), directed at maritime sectors to mitigate emissions of SOx, NOx, and CO2. The IMO envisions...
-
Properties of LiMnBO3 glasses and nanostructured glass-ceramics
PublikacjaPolycrystalline LiMnBO3 is a promising cathode material for Li-ion batteries. In this work, we investigated the thermal, structural and electrical properties of glassy and nanocrystallized materials having the same chemical composition. The original glass was obtained via a standard melt-quenching method. SEM and 7Li solid-state NMR indicate that it contains a mixture of two distinct glassy phases. The results suggest that the...
-
Analysis of the regenerative braking process for the urban traffic conditions
PublikacjaIn a regular drive system, with an internal combustion engine, vehicle braking is connected with the unproductive dissipation of kinetic and potential energy accumulated in the mass of the vehicle into the environment. This energy can constitute up to 70% of the energy used to drive a vehicle under urban conditions. Its recovery and reuse is one of the basic advantages of hybrid and electric vehicles. Modern traffic management...
-
Determination of toxic gases based on the responses of a single electrocatalytic sensor and pattern recognition techniques
PublikacjaA response from an electrocatalytic gas sensor contains fingerprint information about the type of gas and its concentration. As a result, a single gas sensor can be used for the determination of different gases. However, information about the type of gas and its concentration is hidden in the unique shape of the current–voltage response and it is quite difficult to explore. One of the ways to get precise information about the measured...
-
Designate CTOD Heat Affected Zone of butt weld, Report No: WOiO/II/76/2013
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
Frequency response spectra applied to assess efficiency of the training techniques
PublikacjaThe purpose of the research is to assess the increase of the muscle strength and power. Movement of the human body when the moving one impacts a stationary or moving body is taken under consideration. The waveform produced by an impact is transformed into frequency domain. The acceleration record is transformed as a complex spectrum, by the use of a Discrete Fourier Transformation. In this paper the applications of the discrete...
-
Designate CTOD of Weld Metal of butt weld, No WOiO/II/108/2013
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
Designate of CTOD for WM and HAZ, report no: WOiO/II/122/2014
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...
-
Parity vertex colouring of graphs
PublikacjaA parity path in a vertex colouring of a graph is a path along which each colour is used an even number of times. Let Xp(G) be the least number of colours in a proper vertex colouring of G having no parity path. It is proved that for any graph G we have the following tight bounds X(G) <= Xp(G) <=|V(G)|− a(G)+1, where X(G) and a(G) are the chromatic number and the independence number of G, respectively. The bounds are improved for...
-
General grants and development – a relationship without a future? The effects of the structure of general grants on the development of local government units in Poland
PublikacjaThe purpose of this paper is to attempt to identify the reasons for the lack of relationship between general grant revenue and investment expenditure of local government units. The author formulated the hypothesis that there is no link between general grants and investment expenditure and that the reason for this are the current spending on education, absorbing the entire amount of general grants received by local government units....
-
CTOD designation for WM and HAZ in butt joint made from S460 ML steel, Expertise No. WOiO/II/82/2015
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...
-
Highly porous nanoberyllium for X-ray beam speckle suppression
PublikacjaThe speckle suppressor device containing highly porous nanoberyllium is proposed for manipulating with the spatial coherence length and removing undesirable speckle structure during the imaging experiments. We report a special device called the speckle suppressor, which contains the highly porous nanoberyllium plate, compacted from both sides by two beryllium windows. By insertion the speckle suppressor in the X-ray beam it allows...
-
The problem of infections associated with implants – an overview
PublikacjaImplant-associated infections are serious and relatively common complication that leads to implant loss. The purpose of this paper is to gather knowledge about this issue. A literature review of the epidemiology, risk factors and pathogenesis of infections related to implants was carried out. This position collects data on commonly used implants and infections associated with them from various fields of medicine and contains classifications...
-
Pretreatment of Lignocellulosic Materials as Substrates for Fermentation Processes
PublikacjaLignocellulosic biomass is an abundant and renewable resource that potentially contains large amounts of energy. It is an interesting alternative for fossil fuels, allowing the production of biofuels and other organic compounds. In this paper, a review devoted to the processing of lignocellulosic materials as substrates for fermentation processes is presented. The review focuses on physical, chemical, physicochemical, enzymatic,...
-
Rough Sets Applied to Mood of Music Recognition
PublikacjaWith the growth of accessible digital music libraries over the past decade, there is a need for research into automated systems for searching, organizing and recommending music. Mood of music is considered as one of the most intuitive criteria for listeners, thus this work is focused on the emotional content of music and its automatic recognition. The research study presented in this work contains an attempt to music emotion recognition...
-
Implementation of power transformer controlled switching algorithm
PublikacjaThe article presents two new algorithms of controlled switching the power transformer. The main aim of the paper is to obtain formulas that determine the moments of closing of the circuit breaker poles. The study contains projects of control systems for both algorithms. Mathematical formulas for the time instants of the breaker poles closing were developed on the basis of electric circuit theory and magnetic circuit theory. The...
-
OPERATING CONDITIONS OF SLIDE BEARINGS OF MILLS USED IN KGHM POLSKA MIEDŹ S.A.
PublikacjaThe paper contains the results from a tec hnical analysis of the conditions of the operation of hydrodynamic bearings supporting the drums of ore processing mills at KGHM Polska Mied ź S.A. A theoretical analysis was performed on the grounds of onsite examination and measurem ents of principal dimensions of the bearings of interest. The computer simulation covered the characteristics of the oil film in the bearings...
-
HOW EFFICIENT IS NOISE LABELING OF TIRES?
PublikacjaSince 2012 all new tires in Europe must be labeled. The label contains general information about tire performance concerning rolling resistance (that corresponds to fuel economy), noise emission and wet grip (only for passenger car tires). Measurements of noise performance of tires must be performed according to the Annex 3 of the Regulation No 117 of the Economic Commission for Europe of the United Nations. The regulation specifies...
-
Preparation, characterization and anti-colitis activity of curcumin-asafoetida complex encapsulated in turmeric nanofiber
PublikacjaUlcerative colitis (UC) is a main form of inflammatory bowel disease (IBD). Asafoetida (ASF) and turmeric have traditionally been used for the treatment of various inflammatory diseases, including UC, because ASF is rich in sulfur compounds and turmeric contains curcumin (CUR). Turmeric nanofiber (TNF), the modified cell wall component of turmeric is considered to play important role in the human diet, health and can be used as...
-
Towards Greater Citizen Participation in Financing Public Cultural Institutions—Legal Barriers and Proposed Solutions
PublikacjaThe paper contains a conceptual proposal that aims at indicating new models of participatory financing of cultural institutions as well as actions towards supporting culture. It presents results of a qualitative study in the form of action research, on identifying legal barriers of financing of cultural institutions in Poland. Additionally, it presents practical suggestions to the encountered problems that were worked out after...
-
Spatial Visualization Based on Geodata Fusion Using an Autonomous Unmanned Vessel
PublikacjaThe visualization of riverbeds and surface facilities on the banks is crucial for systems that analyze conditions, safety, and changes in this environment. Hence, in this paper, we propose collecting, and processing data from a variety of sensors—sonar, LiDAR, multibeam echosounder (MBES), and camera—to create a visualization for further analysis. For this purpose, we took measurements from sensors installed on an autonomous, unmanned...
-
Evaluation of the potential of Microwave Plasma–Atomic Emission Spectrometry for trace elements leaching assessment from the concrete matrix with sewage sludge ash additives
PublikacjaThe management of ash generated during the thermal utilization of sewage sludge is a significant environmental problem requiring an effective technological solution. One alternative way to dispose of sewage sludge is to bind it in concrete as a substitute for part of the aggregate. The properties of the C-S-H phase enable effective immobilization of harmful substances that sewage sludge contains. The amount of individual compounds...
-
COMPOSITE MATERIAL SELECTION FOR A PATIENT TRANSFER ASSIST DEVICE
PublikacjaLaminates - layered composites containing at least two elements (matrix and reinforcement) widely used in industry have also found their usage in medicine. Their main feature is the ability to modify the material in order to obtain the required properties. Depending on the needs, we can modify reinforcement, type of resin or the method of bonding substrates. Commonly used fibers are: carbon fiber, glass and aramid fibers; resins...
-
Structure-based design and evaluation of novel N-phenyl-1H-indol-2-amine derivatives for fat mass and obesity-associated (FTO) protein inhibition
PublikacjaFat mass and obesity-associated (FTO) protein contributes to non-syndromic human obesity which refers to excessive fat accumulation in human body and results in health risk. FTO protein has become a promising target for anti-obesity medicines as there is an immense need for the rational design of potent inhibitors to treat obesity. In our study, a new scaffold N-phenyl-1H-indol-2-amine was selected as a base for FTO protein inhibitors...
-
The Urban Mentoring as a New Method of Participatory Urban Planning in Poland
PublikacjaTwenty-five years after the return of democracy and the beginning of basing the country's economy on neoliberal developmental paradigm, Poland adopted the regulations regarding management of urban policy, which had been wait for over a decade (accession to the EU). The National Urban Policy as well as the Act on revitalization have defined, in a modern manner, the field of cooperation between the local government, the administration...
-
Aquaponics Based Artificial Biosphere Included in Architecture: From Mitigation of Negative Impacts to Positive Added Values of Urban Spatial Structures on Local, Regional and Global Scale
PublikacjaTechnologies may appear faster than spatial planning can afford it. Alt hough applying new technologies solve particular problems, it may also create new ones. Many negative consequences of implementing new technologies are visible a fter years or decades – they accumulate until the need of solving them. According to The Hannover Principles (McDonough & Braungart 2013) one should, by example not think about...
-
Unravelling the role of electron–hole pair spin in exciton dissociation in squaraine-based organic solar cells by magneto-photocurrent measurements
PublikacjaA high absorption coefficient and narrow absorption bands in squaraine (SQ) dyes have resulted in rapidly growing interest in them as a donor material in photovoltaic devices. The exciton dissociation process in organic systems proceeds via a multistep mechanism where the electron–hole pairs (charge transfer states) involved in the current generation process determine the recombination losses and subsequently limit the overall...
-
CERTIFICATION SYSTEM AS A TOOL FOR IMPROVING THE SAFETY AND SUSTAINABILITY OF SCHOOL-RELATED TRAVELS
PublikacjaDespite the well-established physical, social, emotional, cognitive, and spatial benefits of active and autonomous school commuting of children and adolescents', many are driven by car. Pilot surveys and field research held in 2019 in 10 Gdansk primary schools confirmed this trend. The article presents a certification system for schools, commissioned by the City of Gdańsk, which is an element of a systemic solution shaping patterns...
-
Rotational molding of polylactide (PLA) composites filled with copper slag as a waste filler from metallurgical industry
PublikacjaThe research work carried out so far indicates the ever wider possibilities and demand for shaping composite products in the rotational molding technology. This trend was the main reason to use waste-based filler from the metallurgical process as a filler for manufacturing polylactide (PLA)-based remolded composites. Copper slag (CS) was introduced in the single-step processing method to PLA matrix at 5, 10, 20, and 35 wt%. The...
-
Possibilities for Developing Electromobility by Using Autonomously Powered Trolleybuses Based on the Example of Gdynia
PublikacjaTrolleybus transport refers to contemporary challenges related to a reduction in emissions of greenhouse gases and CO2 into the atmosphere formulated by international institutions, such as the United Nations, the Organisation for Security and Co-operation in Europe, or the European Union. Departure from fossil fuels in urban transport is one of the key challenges for the coming years. Trolleybuses are an important tool in this...
-
Cooperation areas between universities and industry - case studies in the area of civil engineering
PublikacjaThe paper describes the areas of cooperation between universities and industry in the area of civil engineering. Presented examples are related to didactics, research grants and commissioned works. On the basis of the authors own experiences the mutual benefits of cooperation in different areas are described. As well as the assessment criteria of the areas of cooperation by the scientific community. The first area of cooperation...
-
Treatment of landfill leachate by constructed wetlands: three case studies
PublikacjaThe performance of three CW systems treating landfill leachate, two located in northern Poland (Szadółki near Gdańsk and Gatka near Miastko) and one in southern Sweden (Örebro), is discussed. The CWs differ in size, hydraulic regime, type of hydrophytic plants and type of leachate pre-treatment before discharging to the CW. The CW in Szadółki consists of two parallel beds with sub-surface, horizontal flow of leachate (HSSF) planted...
-
Inhomogeneity of low-noise wearing courses evaluated by tire/road noise measurements using the close-proximity method
PublikacjaPerforming numerous analyses of tire/road noise measurements on low-noise pavements during the last several years, the authors observed significant inhomogeneity of the wearing course in numerous cases, while similar problems were almost non-existent when dense pavements were measured. Three main causes of low-noise pavement inhomogeneity can be defined. The first one is imperfections in the technology used for asphalt mix production...
-
LIGHT POLLUTION IN THE CONTEXT OF THREATS TO THE WILDLIFE CORRIDORS
PublikacjaAccess to remote sensing night-time imagery allows for modeling of light pollution Increasingly, data on the propagation of artificial light are a source of interesting information for different fields of science and affect the planning of economic development. The article presents the problem of light pollution in the context of threats to the wildlife corridors in Poland. Wildlife corridors are areas that allow safe migration...
-
Autonomous pick-and-place system based on multiple 3Dsensors and deep learning
PublikacjaGrasping objects and manipulating them is the main way the robot interacts with its environment. However, for robots to operate in a dynamic environment, a system for determining the gripping position for objects in the scene is also required. For this purpose, neural networks segmenting the point cloud are usually applied. However, training such networks is very complex and their results are unsatisfactory. Therefore, we propose...
-
Autonomous Perception and Grasp Generation Based on Multiple 3D Sensors and Deep Learning
PublikacjaGrasping objects and manipulating them is the main way the robot interacts with its environment. However, for robots to operate in a dynamic environment, a system for determining the gripping position for objects in the scene is also required. For this purpose, neural networks segmenting the point cloud are usually applied. However, training such networks is very complex and their results are unsatisfactory. Therefore, we propose...
-
Behavior of residual current devices at earth fault currents with DC component
PublikacjaLow-voltage electrical installations are increasingly saturated with power electronic converters. Due to very high popularity of photovoltaic (PV) installations and the spread of electric vehicles (EV) as well as their charging installations, DC–AC and AC–DC converters are often found in power systems. The transformerless coupling of AC and DC systems via power electronic converters means that an electrical installation containing...
-
Intense and stable room-temperature photoluminescence from nanoporous vanadium oxide formed by in-ambient degradation of VI3 crystals
PublikacjaVanadium oxides have attracted research interest because their optoelectronic properties make them optically active with room-temperature photoluminescence (PL) emission, which, however, is not sufficiently intense for real applications. For this reason, many nanostructured vanadium oxides are currently fabricated through several precursors and different treatments to improve the PL efficiency and enhance the PL intensity. Herein,...
-
Photoresponsive Amide-Based Derivatives of Azobenzene-4,4′-Dicarboxylic Acid—Experimental and Theoretical Studies
PublikacjaAzobenzene derivatives are one of the most important molecular switches for biological and material science applications. Although these systems represent a well-known group of compounds, there remains a need to identify the factors influencing their photochemical properties in order to design azobenzene-based technologies in a rational way. In this contribution, we describe the synthesis and characterization of two novel amides...
-
Synthesis and electrochemical characteristics of novel dithiocarbamate polymers
PublikacjaNovel dithiocarbamate compounds have been obtained by reacting a linear poly(ethylenimine)polymer, MW 50,000, with CS2. The resulting anionic polymers contain, depending on the reaction conditions, up to two sulfur atoms per one nitrogen atom (approx. 40% w/w). The polymers are soluble in dimethylsulfoxide and insoluble in acetonitrile solutions. In both solvents they are electrochemically active, in the latter case as a cast film...
-
Performance of microbial fuel cells operated under anoxic conditions
PublikacjaNowadays, microbial fuel cells (MFC) stand up as a promising renewable energy source. Due to the ability of the MFC to oxidize a wide spectrum of substrates, wastewater seems to be one of the most interesting fuels. Unfortunately, wastewater could contain electron acceptors such as nitrate, which could interfere with the electrical performance of the MFC. In this work, the influence of oxidised nitrogen forms on the electricity...
-
Analytical and legislative challenges of sewage sludge processing and management
PublikacjaThis article presents the most popular methods of sewage sludge management and analytical techniques which could be a powerful tool in designing new sewage sludge management methods. Chemical analysis is also described as a vital point at the subsequent stages of technological processes control and sewage sludge quality assessment. It is also an instrument essential to maintaining control of processed sewage sludge introduced to...
-
Selected anionic and cationic surface active agents determined in river sediments – the Klodnica catchment
PublikacjaSurface active agents (SAAs) are specific compounds that contain hydrophilic/ hydrophobic group in their molecules named as amphiphilic structures. According to charge on the hydrophilic part of surfactants they can be classified into three main groups: anionic, cationic and non-ionic compounds. Due to the amphiphilic structure of SAAs they have specific properties (e.g. ability to adsorption at different surfaces, reduction of...
-
Methods for quality improvement of multibeam and LiDAR point cloud data in the context of 3D surface reconstruction
PublikacjaPoint cloud dataset is the transitional data model used in several marine and land remote-sensing applications. During further steps of processing, the transformation of point cloud spatial data to more complex models containing higher order geometric structures like edges and facets may be possible, if an appropriate quality level of input data is provided. Point cloud datasets usually contain a considerable amount of undesirable...