Filtry
wszystkich: 361
wybranych: 242
Wyniki wyszukiwania dla: CIRCUMFERENTIAL SLOTS
-
The FEM analysis of pressure installation elements after simulated accidental overheating
PublikacjaThe paper presents innovative analysis focused on the safety aspects of existing pressure installation operation after overheating accidents. Results presented here can be applied in decision-making process concerning further operation of existing pressure installation after cooling system failure. In this paper the results of FEM analysis performed for a straight pipe and 90 degrees elbow, made of super duplex stainless steel,...
-
Reduction of Derivative pipeline effort in water turbine
PublikacjaThe paper presents an approach to evaluate and reduce the effort of the derivative pipeline in a water turbine of a hydrostatic power station in its vulnerable spots. Potential places of the biggest effort of the structure, as well as the coefficient of displacement and safety factor related to them were identified using FEM numerical method. Pipeline reinforcement was designed and made based on FEM analysis. Original technology...
-
Optimization of clamping stiffness during milling of high-dimensional structures with the use of techniques of experiment – aided virtual prototyping
PublikacjaThe subject of this paper is a method of searching for conditions of minimizing the vibration level of a tool-high dimensional flexible workpiece, at unchangeable technological parameters of the machining process. It depends on repeatable change of the values of the stiffness coefficients as soon as an optimal vibration state of the workpiece approaches. There are assessed the values of dominant ”peaks” in the frequency spectra...
-
Design and Characterization of a Planar Structure Wideband Millimeter-Wave Antenna with Wide Beamwidth for Wearable off-body Communication Applications
PublikacjaThis letter presents the design of a planar single-layer wideband antenna featuring wide beamwidth has well as high and stable in-band gain. The proposed antenna is a planar monopole fed by a bottom-grounded coplanar waveguide to realize wide beamwidth in both the xz- and yz-planes. Simultaneous optimization of all adjustable antenna parameters, carried out at the full-wave electromagnetic simulation level. The constructive interference...
-
Compact Dual-Polarized Corrugated Horn Antenna for Satellite Communications
PublikacjaIn this paper, a structure and design procedure of a novel compact dual-polarized corrugated horn antenna with high gain and a stable phase center for satellite communication is presented. The antenna incorporates an Ortho-Mode Transducer (OMT), a mode converter, and a corrugated structure. The compact OMT section is designed to be fed by standard WR-75 waveguides. The proposed compact design utilizes only ten corrugated slots...
-
Acoustic Detector of Road Vehicles Based on Sound Intensity
PublikacjaA method of detecting and counting road vehicles using an acoustic sensor placed by the road is presented. The sensor measures sound intensity in two directions: parallel and perpendicular to the road. The sound intensity analysis performs acoustic event detection. A normalized position of the sound source is tracked and used to determine if the detected event is related to a moving vehicle and to establish the direction of movement....
-
Novel Structure and EM-Driven Design of Small UWB Monopole Antenna
PublikacjaA novel structure of a small UWB monopole antenna is presented. In our approach, a compact size is achieved by means of a meander line for current path enlargement as well as the two parameterized slits that introduce additional degrees of freedom helping to ensure good impedance matching. The antenna design is carried out using surrogate-based optimization involving variable-fidelity EM simulations. This allows us to simultaneously...
-
A Geometrically Simple Compact Wideband Circularly Polarized Antenna
PublikacjaA compact broadband wide-slot circular polarization (CP) antenna is proposed. An inverted L-shape parasitic strip at the open end of a microstrip line extension and a slot modification is applied to attain wideband CP. The advantage of this technique is simplicity which makes it readily re-designable for different frequency bands. To demonstrate the concept, three designs working at different frequencies are obtained. The redesign...
-
Does low price mean high competitiveness
PublikacjaWe found a strong positive relationship between Comparative Price Level Index (CPL) and Growth Competitiveness Index (GCI). We do realize that the relation we have found does not have to indicate cause and effects relationship. Competitiveness is a process which goes far beyond price level but it is detemined by lots of different elemnts. We show the GCI composition that provides a concept explaining what exactly determines competitiveness...
-
Excited-state proton transfer and geminate recombination in the molecular cage of β-cyclodextrin
PublikacjaExcited-state proton transfer and geminate recombination in aqueous heptakis(2,6-di-O-methyl)-β-cyclodextrin have been compared with those in water by monitoring the photoinduced prototropic tautomerization of 6-hydroxyquinoline, which occurs via forming anionic intermediate. Enol deprotonation decelerates by 18 times whereas its reverse process accelerates slightly with encapsulation. The imine protonation of the intermediate...
-
Mathematical Models in Design Process of Ship Bow Thrusters
PublikacjaThe paper describes an application of simulation models for computer-aided design of ship bow thrusters. Generation of simulation models of ship bow thruster requires development and verifying of mathematical models of system component elements. Using the results of simulation the expert system is able to determine, that the rules of classification societies are met. Design procedures and mathematical models are part of an expert...
-
Mathematical Models in Design Process of Ship Bow Thrusters
PublikacjaThe presentation is about an application of simulation models for computer-aided design of ship bow thrusters. Generation of simulation models of ship bow thruster requires development and verifying of mathematical models of system component elements. Using the results of simulation the expert system is able to determine, that the rules of classification societies are met. Design procedures and mathematical models are part of an...
-
Selected aspects of logistics management of the production process in an enterprise
PublikacjaThe following article presents selected aspects of management of production logistics process in enterprise. Companies treat this part of business as a way to empower market position. In the first part author explained the idea of process. The next part describes the definition of logistics production management, which is crucial for manufacturing enterprises. However, author described lots of tools related to production management...
-
BADANIA SYMULACYJNE PROWADZONE W ŚRODOWISKU SYSTEMU EKSPERTOWEGO STOSOWANE DO WSPOMAGANIA PROJEKTOWANIA UKŁADÓW AUTOMATYKI STATKU
PublikacjaW referacie przedstawiono wykorzystanie badań symulacyjnych jako źródła wiedzy dla systemu ekspertowego. Omawiany system służy wspomaganiu doboru elementów steru strumieniowego. Elementami tego systemu są: biblioteka struktur, biblioteka modeli, baza elementów oraz baza wiedzy. Jako przykład przedstawiono badania symulacyjne struktury steru strumieniowego zawierającej silnik indukcyjny, wał śrubowy, śrubę o skoku nastawnym oraz...
-
Charakterystyka hydrogeochemiczna wód podziemnych rejonu Przylądka Rozewie na podstawie badań ich naturalnych wypływów
PublikacjaW niniejszym artykule zostały przedstawione wyniki badań, które były prowadzone w strefie brzegowej rejonu Przylądka Rozewie. Prowadzone w latach 2013-2014 badania miały charakter monitoringu podstawowych właściwości fizykochemicznych oraz oznaczenia składu jonowego wód wypływających ze zbocza w obrębie badanego terenu. Warunki hydrogeochemiczne rejonu Przylądka Rozewie są kształtowane pod wpływem specyficznego nadmorskiego klimatu,...
-
Metoda prognozowania mocy skrawania przy przecinaniu piłami polskiego drewna sosnowego z uwzględnieniem wiązkości materiału obrabianego
PublikacjaW pracy zostały przedstawione wartości właściwości materiałowych tj.: wiązkość R oraz naprężenia tnące w strefie skrawania τy, dla drewna sosnowego (Pinus sylvestris L.). Badane próbki drewna pochodziły z czterech Krain Przyrodniczo - Leśnych Polski: Bałtyckiej Krainy Przyrodniczo - Leśnej (kraina A), Karpackiej Krainy Przyrodniczo - Leśnej (kraina B), Małopolskiej Krainy Przyrodniczo - Leśnej (kraina C) oraz Wielkopolsko - Pomorskiej...
-
Application of gaze tracking technology to quality of experience domain
PublikacjaA new methodological approach to study subjective assessment results employing gaze tracking technology is shown. Notions of Human-Computer Interaction (HCI) and Quality of Experience (QoE) are shortly introduced in the context of their common application. Then, the gaze tracking system developed at the Multimedia Systems Department (MSD) of Gdansk University of Technology (GUT) is presented. A series of audio-visual subjective...
-
Comparative analysis of numerical with optical soliton solutions of stochastic Gross–Pitaevskii equation in dispersive media
PublikacjaThis article deals with the stochastic Gross–Pitaevskii equation (SGPE) perturbed with multiplicative time noise. The numerical solutions of the governing model are carried out with the proposed stochastic non-standard finite difference (SNSFD) scheme. The stability of the scheme is proved by using the Von-Neumann criteria and the consistency is shown in the mean square sense. To seek exact solutions, we applied the Sardar subequation...
-
Broad Stopband, Low-Loss, and Ultra-Compact Dual-Mode Bandpass Filter Based on HMSIRC
PublikacjaIn this investigation, an ultra-compact dual-mode bandpass filter (BPF) with a wide stopband re-sponse is realized by using a half-mode substrate-integrated rectangular cavity (HMSIRC). The HMSIRC resonator is designed with a cavity that is rectangular in shape and has metallic vias along three of the sides. The fourth side is open-ended and contains microstrip feed lines. For the purpose of constructing a magnetic wall, a rectangular...
-
Highly-Miniaturized Dual-Mode Bandpass Filter Based on Quarter-Mode Substrate Integrated Waveguide with Wide Stopband
PublikacjaThis paper presents a novel design of a highly-miniaturized dual-mode bandpass filter (BPF) employing a quarter-mode substrate integrated waveguide (QMSIW). The QMSIW resonator is based on a square cavity with metallic vias along two sides, and open-ended edges at the remaining sides that contain orthogonal feed lines. An open slot is introduced along the two sides of the square cavity with metallic vias to form a magnetic wall....
-
Design of compact self-quintuplexing antenna with high-isolation for penta-band applications
PublikacjaThis article presents a novel compact self-quintuplexing antenna architecture based on a substrate-integrated rectangular cavity (SIRC) for pentaband applications. The proposed self-quintuplexing antenna is constructed by employing an SIRC, one Pi-shaped slot (PSS), one T-shaped slot (TSS), and five 50Ω microstrip feedlines. The PSS and TSS are engraved on the top of the SIRC to create five radiating patches, which are excited...
-
Diagnosing marine turbine engines through energy characteristics of their flow section
PublikacjaThe aim of the performed research was to develop of diagnostic method of the flow section of a marine turbine combustion engine based on the level of delamination of its energy characteristics. The here adopted diagnostic model provides for a formulation of the evaluation of the technical conditions based on the measurements of the parameters of the thermodynamic medium in the characteristic control cross-sections of the engine...
-
A structure and design of a novel compact UWB MIMO antenna
PublikacjaIn the paper, a concept and design procedure of a novel compact MIMO slot antenna is presented. In order to achieve a better filling of available space, individual antennas are constrained to a triangular shape and optimized for a reduced size. The MIMO structure is then assembled using the two of previously designed antennas in orthogonal arrangement. Surrogate-assisted numerical optimization involving variable-fidelity electromagnetic...
-
Pin-on-Substrate Gap Waveguide: An Extremely Low-Cost Realization of High-Performance Gap Waveguide Components
PublikacjaConsidering the limitations of currently available technologies for the realization of microwave components and antennas, a trade-off between different factors including the efficiency and fabrication cost is required. The main objective of this letter is to propose a novel method for the realization of gap waveguides (GWGs) that take advantage of conventional PCB fabrication technology, thus are low cost and light weight. Moreover,...
-
Highly-Miniaturized Self-Quadruplexing Antenna Based on Substrate-Integrated Rectangular Cavity
PublikacjaThis paper introduces a novel self-quadruplexing antenna (SQA) architecture using a substrate-integrated rectangular cavity (SIRC) for compact size, wide-frequency re-designability, and high isolation responses. The proposed SQA is developed by engraving two U-shaped slots (USSs) on the top conductor of the SIRC. The USSs are excited by employing four microstrip feedlines to achieve self-quadruplexing antenna characteristics. The...
-
Circular polarization diversity implementation for correlation reduction in wideband low-cost multiple-input-multiple-output antenna
PublikacjaIn this paper, a multiple-input-multiple-output (MIMO) antenna featuring circular polarization diversity, and designed on a common coplanar ground is presented. The proposed antenna design utilizes a coplanar waveguide (CPW) feeding technique with three parallel coplanar ground planes, and two feedlines in-between. For circular polarization (CP), quasi-loops are created by etching slots on the outermost ground planes. With this...
-
Atmospheric deposition in coniferous and deciduous tree stands in Poland
PublikacjaThe objective of this study was to assess the transformation of precipitation in terms of quantity and chemical composition following contact with the crown layer in tree stands with varied species composition, to investigate the effect of four predominant forest-forming species (pine, spruce, beech, and oak) on the amount and composition of precipitation reaching forest soils, and to determine the sources of pollution in atmospheric...
-
Selektywne chłodzenie mózgu noworodka po Niedotlenieniu okołoporodowym. Część 1. Medyczne fakty oraz przegląd dostępnych rozwiązań systemów selektywnego chłodzenia mózgu
PublikacjaMózg ludzki jest organem delikatnym, dlatego tak ważne jest zadbanie o to, aby już w momencie przyjścia na świat noworodek miał zapewnioną, w razie konieczności możliwość minimalizacji uszkodzeń neurologicznych, spowodowanych niedotlenieniem okołoporodowym. Niedotlenienie to w dramatyczny sposób zaburza homeostazę mózgu, który jako organ najbardziej energochłonny potrzebuje najwięcej tlenu. Zapoczątkowane brakiem tlenu procesy...
-
Experiment-aided virtual prototyping to minimize tool-workpiece vibration during boring of large-sized structures
PublikacjaThe paper presents the author's method of solving the problems of vi-bration suppression during boring of large-sized workpieces by means of an in-novative method of adjusting the rotational speed of the boring bar. It consists in selecting the spindle speed in accordance with the results of the cutting process simulation. The method includes identification of the model of the finite element method of the boring bar. The Root Mean...
-
Tribological model of porous bearings with particular attention given to the lubricant lubricity
PublikacjaThe friction and wear problems, accompanying all the tribological systems, lead to reduced service life. In order to prevent such situation, it is necessary to maintain fluid friction, which improves durability of all friction nodes in a tribological system. In the paper, the tribological system consists of porous bearings and the model deals with their weakest spots - the oil outflow points in the porous wall. A kinetic model...
-
Fracture mechanics model of cutting power versus widespread regression equations while wood sawing with circular saw blades
PublikacjaA comparison of the theoretical cutting power consumption results forecasted with the model (FM_CM model) which include work of separation (fracture toughness) in addition to plasticity and friction, and two widespread regression equations while wood sawing with circular saw blades has been described. in and cutting power consumption forecasted. In computations of the cutting power consumption during rip sawing of Scots pine wood...
-
Empirical verification in industrial conditions of fracture mechanics models of cutting power prediction
PublikacjaA comparison of experimental results obtained in the industrial conditions at a sawmill located in the Baltic Natural Forest Region (PL) and theoretical cutting power consumption forecasted with the models which include work of separation (fracture toughness) in addition to plasticity and friction has been described. In computations of cutting power consumption during rip sawing of Scots pine wood (Pinus sylvestris L.) values of...
-
Design of Microwave Lossy Filter Based on Substrate Integrated Waveguide (SIW)
PublikacjaIn this letter, we propose a lossy three-pole Chebyshev filter centered at 5.15 GHz, based on the substrate integrated waveguide (SIW) with scattering characteristics shifted down by 5.68 dB. The filter is composed of three directly coupled SIW cavities with three lossy couplings between nonadjacent resonators. These additional couplings are realized using mixed coupled slot and microstrip lines connected with metal electrode leadless...
-
A Dual-Polarized 39 GHz 4x4 Microstrip Antenna Array for 5G MU-MIMO Airflight Cabin Connectivity
PublikacjaThis paper presents the design, fabrication, and experimental validation of a 39 GHz dual-polarized 4x4 microstrip antenna array. The array consists of 16 slot coupled circular microstrip patches, fed through SMPS connectors. The procedure requiring a reduced number of cables for measurement of the uniformly excited antenna array is also presented. The array exhibits 18 dBi peak gain and 2.9 GHz reflection bandwidth and is intended...
-
Odtwarzanie przebiegu trasy kolejowej o złożonym ukształtowaniu geometrycznym
PublikacjaKształt eksploatowanych torów kolejowych jest w niektórych sytuacjach bardzo złożony, a jednocześnie − jak wykazały przeprowadzone ciągłe pomiary satelitarne − niekiedy tak zdeformowany, że określenie kierunków głównych okazuje się niemożliwe.W pracy przedstawiono program komputerowy do odtwarzania przebiegu trasy kolejowej w takich właśnie przypadkach. Przygotowano zestaw funkcji realizujących połączenia prostych i łuków kołowych...
-
Shape Memory Alloy-Based Fluidically Reconfigurable Metasurfaced Beam Steering Antenna
PublikacjaA low-cost actuator-based fluidically programmable metasurface (FPMS) antenna is proposed to solve the slow tuning speed problem of the manually fluidic based reconfigurable antennas. The FPMS-based antenna is probe-fed and comprises a 4 × 4 square ring metasurface as a superstrate. Moreover, two shape memory alloy (SMA)-based electrically-controlled actuators are employed in the design for controlling the position of the 3D-printed...
-
An Innovative Antenna Array with High Inter Element Isolation for Sub-6 GHz 5G MIMO Communication Systems
PublikacjaA novel technique is shown to improve the isolation between radiators in antenna arrays. The proposed technique suppresses the surface-wave propagation and reduces substrate loss thereby enhancing the overall performance of the array. This is achieved without affecting the antenna’s footprint. The proposed approach is demonstrated on a four-element array for 5G MIMO applications. Each radiating element in the array is constituted...
-
Water uptake and energetics of the formation of barium zirconate based multicomponent oxides
PublikacjaA group of multi-component oxides based on BaZrO3 have been prepared using a solid-state reaction method and examined in terms of their water uptake and thermodynamics of formation. Depending on the type and amount of acceptor substitution, the synthesized compounds exhibit various proton defect concentrations, reaching up to 0.2 mol/mol for a compound containing 10 different elements in the B-sublattice, where 50% of them are...
-
Performance of organic coatings upon cyclic mechanical load
PublikacjaA number of engineering structures fail due to the fatigue damage resulting from cyclic mechanical stress. However, as far as organic coatings are concerned this degradation factor remains underestimated. In the paper the authors propose a methodology combining global electrochemical impedance spectroscopy and local atomic force microscopy measurements for evaluation of coating resistance to an impact of repetitive mechanical stress. Typical...
-
Survey on Applications of Multimedia Technology to Examine Impact of Roadside Advertising on Drivers
PublikacjaThe correct location of ads, both static and moving, in close proximity of the roadway is an issue of high significance in the context of road safety. This publication aims to provide support in solving these issues by presenting a range of options for the implementation of extensive, multi-faceted research, using modern technology to allow an objective assessment of the risks arising from the presence of advertising spots in the...
-
Structure and computationally-efficient simulation-driven design of compact UWB monopole antenna
PublikacjaIn this letter, a structure of a small ultra-wideband (UWB) monopole antenna, its design optimization procedure as well as experimental validation are presented. According to our approach, antenna compactness is achieved by means of a meander line for current path enlargement as well as the two parameterized slits providing additional degrees of freedom that help to ensure good impedance matching. For the sake of reliability, the...
-
Modeling and Evaluation of Electric Treeing Phenomena in Polymeric Cable Insulation
PublikacjaThis paper investigates the treeing phenomenon in polymeric materials such as crosslinked polyethylene (XLPE) that is widely used in medium and high voltage power cables as primary insulation. The modeling of electrical tree growth in the insulation from its initiation to breakdown is significant research work that illustrates the discharge dynamics and its impact on aging process in polymeric insulation. This study utilizes pulse...
-
The influence of sound track on the viewer’s emotions and correction of the color in the film
PublikacjaThe article presents the aspects of the final selection of colors in film production based on the emotions caused by the soundtrack of the film. First, the processing of colors, contrast, saturation and white balance of shots in the film was presented. The definition of color grading is also described, i.e. the color changes in the film's views. In the second part of the article, the soundtracks of the film were analyzed, in particular...
-
MODELLING OF TRANSIENT FLOW IN STORM SEWERS
PublikacjaThe paper focuses on the assessment of second-order explicit numerical scheme for unsteady flows in sewers. In order to simulate the pressurized flow the 'Preissmann slot' concept is implemented. For simulation of the transcritical flow the original and improved McCormack scheme is used. The calculated results are compared with numerical solutions and laboratory measurements published in the technical literature. Moreover, the...
-
Rotor-Flux Vector based Observer of Interior Permanent Synchronous Machine
PublikacjaThe sensorless control system of the interior permanent magnet machine is considered in this paper. The control system is based on classical linear controllers. In the machine, there occurs non-sinusoidal distribution of rotor flux together with the slot harmonics, which are treated as the control system disturbances. In this case, the classical observer structure in the (d-q) is unstable for the low range of rotor speed resulting...
-
Cost-efficient design optimization of compact patch antennas with improved bandwidth
PublikacjaIn this letter, a surrogate-assisted optimization procedure for fast design of compact patch antennas with enhanced bandwidth is presented. The procedure aims at addressing a fundamental challenge of the design of antenna structures with complex topologies, which is simultaneous adjustment of numerous geometry parameters. The latter is necessary in order to find a truly optimum design and cannot be executed-at the level of high-fidelity...
-
A Compact Self-Hexaplexing Antenna Implemented on Substrate-Integrated Rectangular Cavity for Hexa-Band Applications
PublikacjaThis brief introduces a novel architecture of a compact self-hexaplexing antenna (SHA) implemented on a substrate-integrated rectangular cavity (SIRC) for hexa-band applications. The proposed SHA is configured by using an SIRC resonator, two Pi-shaped slots (PSSs), and six 50Ω microstrip feedlines. The PSSs are connected back-to-back and loaded on top of the SIRC resonator to produce six patch radiators (PRs). The PRs are excited...
-
Energy efficient indoor localisation for narrowband internet of things
PublikacjaThere are an increasing number of Narrow Band IoT devices being manufactured as the technology behind them develops quickly. The high co-channel interference and signal attenuation was seen in edge Narrow Band IoT devices make it challenging to guarantee the service quality of these devices. To maximize the data rate fairness of Narrow Band IoT devices, a multi-dimensional indoor localization model is devised, consisting of...
-
Dielectric Spectroscopy Studies and Modelling of Piezoelectric Properties of Multiferroic Ceramics
PublikacjaCompounds and solid solutions of bismuth ferrite (BiFeO3)—barium titanate (BaTiO3) system are of great scientific and engineering interest as multiferroic and potential high-temperature lead-free piezoelectric materials. In the present paper, the results of research on the synthesis and characterisation of 0.67Bi1.02FeO3–0.33BaTiO3 (67BFBT) ceramics in terms of crystal structure and dielectric and piezoelectric properties are reported....
-
Synergistic effects of a swirl generator and MXene/ water nanofluids used in a heat exchanger pipe of a negative CO2 emission gas power plant
Publikacjafocus on optimizing heat exchangers contributes to improved temperature control mechanisms, ensuring the sustainable operation of innovative power plants working towards negative CO2 emissions. In the realm of oxy-combustion within Negative CO2 Emission Power Plants (nCO2PP), the temperature of combustion products surpasses 3000 (K). Addressing this challenge, the imperative arises to reduce these elevated temperatures to a manageable...