Filtry
wszystkich: 1330
wybranych: 1140
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: SUPERDUPLEX STEEL
-
Weldability of S460ML High Strength Low Alloy Steel in Underwater Conditions
PublikacjaThe paper presents experimental evaluation of susceptibility of the high strength S460ML steel to cold cracking in the conditions of wet welding with the use of covered electrodes. From the results of Tekken tests it was found out that the investigated steel was characterised, in the conditions of the carried out experiments (underwater wet welding and air welding with rutile electrodes), of high susceptibility to cold cracking....
-
Determination of Mechanical Properties of P91 Steel by Means of Magnetic Barkhausen Emission
PublikacjaIn this work, an attempt at determination of mechanical properties by means of a method based on magnetic Barkhausen emission measurements was proposed. The specimens made of P91 steel were subjected to creep or plastic flow which were interrupted after a range of selected time periods in order to achieve specimens with an increasing level of strain. Subsequently, measurements of magnetic Barkhausen emission were carried out, and...
-
Response of a steel tank during earthquakes and mining tremors - experimental investigation
PublikacjaCylindrical steel tanks are very popular shell structures used to store the products of chemical and petroleum industries. Any failure might have disastrous consequences, therefore their safety and reliability is essential. Earthquakes are the most dangerous and also the most unpredictable dynamic loads acting on such structures. On the other hand, mining tremors are usually considered to be less severe due to lower acceleration...
-
Diagnosis of Damage in a Steel Tank Model by Shaking Table Harmonic Tests
PublikacjaDiagnosis of damage in civil engineering structures has recently become an important issue in the safety assessment procedure. Among a number of different approaches, a method of measuring the changes in natural frequencies is one of the most effective indicators of global damage. It has been successfully applied to relatively small. structures, however, the tests on large structures are very difficult and the practical application...
-
PROBLEMS OF COLLISIONS BETWEEN ADJACENT STEEL STRUCTURES UNDER EARTHQUAKE EXCITATION
PublikacjaNowadays, the high level of urbanization forces the engineers to design closely-separated structures and to take into account many factors influencing their response, including collisions between them due to insufficient separation distance during moderate to strong ground motions. Recent observations as well as experimental and numerical investigations have confirmed that interactions...
-
Underwater Wet Repair Welding of API 5L X65M Pipeline Steel
PublikacjaThis paper presents results of the research of effect of polymer insulation of pipeline made of API 5L X65M steel as well as underwater wet welding parameters on properties of joints made by covered electrodes. Effect of heat input on structure and hardness of joints during repair of underwater pipeline was analyzed. Welding defects like microcracks, micro-lacks of fusion, slag inclusions, as well as HAZ hardness increase over...
-
Modal Analysis of a Steel Radial Gate Exposed to Different Water Levels
PublikacjaWith the increase in water retention needs and planned river regulation, it might be important to investigate the dynamic resistance of vulnerable elements of hydroelectric power plants, including steel water locks. The most frequent dynamic loads affecting hydroengineering structures in Poland include vibrations caused by heavy road and railway traffic, piling works and mining tremors. More destructive dynamic loads, including...
-
Guided wave propagation for assessment of adhesive bonding between steel and concrete
PublikacjaAdhesive bonding is becoming more increasingly important in joining of structural elements. In civil engineering, there is a growing interest in connection by adhesive bonding in steel-concrete flexural members. This study concerns the guided wave propagation technique applied to condition assessment of an adhesive connection between a steel member and a concrete beam. Various states of degradation were considered by producing...
-
High Rise Building: The Mega Sculpture Made Of Steel, Concrete and Glass
PublikacjaHigh rise building has transformed from providing not only the expansion of floor space but functioning as mega sculpture in the city. The shift away from economic efficiency driven need is only expected to grow in the future. Based on literature studies; after analysing planning documents and case studies, it was examined whether the presumption that gaining the maximum amount of usable area is the only driving factor; or if the...
-
Degradation of protective coatings in steel chimneys of flue gas desulfurisation system
PublikacjaThis paper presents problems associated with corrosion of steel stacks and changes in philosophy of corrosion protection when implemented into flue gas desulphurization systems. In-situ tests were taken by means of electrochemical impedance spectroscopy at the stack which discharges flue gas before wet lime/limestone desulphurization. A very quick electrolyte absorption by the spherical infill vinylester coating was found using...
-
Comparison of Vacuum Sintered and Selective Laser Melted Steel AISI 316L
Publikacja -
Guided Waves in Steel Rails – Experimental Works and Wavelet Signal Processing
Publikacja -
Analysis of the amount of retained austenite in the structure of steel rolls for sheet rolling
Publikacja -
Properties of surface layers of duplex stainless steel after burnishing processes
PublikacjaStress corrosion cracking resistance of cold worked layers of 25 Cr duplex stainless steel grade UR52N+ has been investigated. The surface layers were performed through burnishing treatment. The residual stresses at surface layers were determined using grazing angle incidence X-ray diffraction method (g-sin2 Ψ). Corrosion tests were performed with the use of Slow Strain Rate Test technique in boiling 35% MgCl2 solution. It has...
-
Stresses in the zone of process openings in the shell of a vertical cylindrical steel tank
PublikacjaW dolnej części płaszcza zbiornika walcowego na ciecze konieczne jest wykonanie różnego rodzaju otworów technologicznych. Artykuł poświęcony jest analizie stanu naprężeń w strefie wzmocnień wykonywanych w sąsiedztwie otworów na rurociągi oraz na włazy wyczystkowe w płaszczu zbiornika. Ponieważ charakter zmian naprężeń, a więc i wzmocnień w strefie obu rodzajów otworów jest różny dlatego artykuł podzielony jest na dwie części, z...
-
Diagnosis of Damage in a Steel Tank Model by Shaking Table Harmonic Tests
PublikacjaThe aim of the present paper is to show the results of the shaking table experimental study concerning the diagnosis of damage in a model of cylindrical steel tank with self-supported roof which is filled with liquid. During the tests, the base of the structure was excited under the harmonic loading with variable frequency. The tests were repeated for different stages of damage, which was introduced in the model by easing the bolts...
-
Hydrogen effects in duplex stainless steel welded joints - electrochemical studies
PublikacjaIn this work results on the influence of hydrogen on passivity and corrosion resistance of 2205 duplex stainless steel (DSS) welded joints are described. The results were discussed by taking into account three different areas on the welded joint: weld metal (WM), heat-affected zone (HAZ) and parent metal. The corrosion resistance was qualified with the polarization curves registered in a synthetic sea water. The conclusion is that,...
-
Evaluation of porous 430L stainless steel for SOFC operation at intermediate temperatures
PublikacjaW pracy przedstawiono badania porowatej stali nierdzewnej typu 430L do zastosowań w tlenkowych ogniwach paliwowych jako podłoża. Podłoża były poddawane utlenianiu w powietrzu oraz w wodorze i analizowane z wykorzystaniem mikroskopu elektronowego, dyfrakcji rentgenowskiej i termograwimetrii cyklicznej.
-
Identification i simulation of initial geometric imperfection of steel cylindrical tanks
PublikacjaPrzedstawiono stochastyczną analizę stalowych zbiorników walcowych ze wstępnymi imperfekcjami geometrycznymi. Wykorzystano pomierzone odchyłki rzeczywistych zbiorników. Imperfekcje opisano za pomocą nienorodnych pól losowych. Wygenerowano realizacje odpowiadające pomierzonym imperfekcjom a także imperfekcjom ekstremalnym. Wykonano obliczeniach geometrycznie i materiałowo nieliniowe zbiornika z imperfekcjami. Wykazano, że imperfekcje...
-
Cavitation erosion of X5CrNi18-10 austenitic stainless steel alloyed with TiC
PublikacjaPraca prezentuje zmianę odporności kawitacyjnej stali X5CrNi18-10 po laserowym stopowaniu jej warstwy wierzchniej węglikiem TiC. Laserowe stopowanie przeprowadzono dla 2 wariantów. W pierwszym przypadku stal stopowano do zawartości 1,55 TiC a w drugim do zawartości 3,97% TiC. Uzyskane rezultaty wskazują że przy zawartości 3,97 TiC nastopiło znaczące zwiększenie odporności na plastyczne odkszyałcenie warstwy wierzchniej pod wpływem...
-
Stress analysis in the steel tank shell at its connection with product pipeline
PublikacjaPrzeanalizowano zaburzenia stanu błonowego w powłoce zbiornika walcowego pionowego w strefie przyłączenia do płaszcza rurociągu produktowego
-
Problems of strength modelling of steel sandwich panels under in-plate load
PublikacjaW pracy omówiono zagadnienia wytrzymałości statycznej stalowych paneli typu sandwich spawanych laserowo. Omówiono charakterystyki sztywności podczas zginania, przedstawiono zachowanie pod obciążeniem równomiernie rozłożonym a także sposób niszczenia pod obciążeniem ściskającym. Omówiono możliwości stosowania takich konstrukcji na podstawie wniosków z badań.
-
Hydrogen induced degradation of structural steel exposed to the technical liquid hydrocarbons
PublikacjaBadano degradacje stali 26H2MF w mieszaninach węglowodorów. Badania były prowadzone pod stałym obciążeniem i przy małej prędkości 10-6s-1
-
Interlayer defect evolution in an coating system on steel under hydromechanical loading
PublikacjaZaprezentowano wyniki pomiarów impedancyjnych obszaru międzywarstwowego w systemie powłokowym poddanym naprężeniom. Przedstawiono nowy sensor który jest zdolny do detekcji defektów w obszarze międzywarstwowym. Dwuwarstwowy system powłokowy przeznacziony do zastosowań morskich zbadano w celu określenia jego odporności na oddziaływanie cyklicznych naprężeń i zanurzeń w 3% roztworze NaCl.
-
Guided waves in steel rails - experimental works and wavelet signal processing
PublikacjaW artykule zaprezentowano analizę falkową pomierzonych eksperymentalnie fal sprężystych wzbudzanych w szynach kolejowych.
-
Surface roughness analysis of hardened steel after high‐speed milling
Publikacja -
The influence of antiwear additive concentration on the tribological behaviour of a-C:H:W/steel tribosystem
Publikacja -
Influence of sulphur on high temperature degradation of steel structures in the refinery industry
PublikacjaArtykuł stanowi przegląd skutków wpływu związków siarki, znajdujących się w mediach procesowych instalacji rafineryjnych, na elementy konstrukcji ze stali węglowych i stopowych. Wyróżniono dwa aspekty wysokotemperaturowej korozji siarkowej: związany z tworzeniem się zgorzeliny siarczkowej i ubytkami masy oraz dotyczący wewnętrznej degradacji elementu w wyniku zmian mikrostruktury stali. Przedstawiono tzw. zmodyfikowane krzywe McConomy...
-
Elastic wave propagation for condition assessment of steel bar embedded in mortar
PublikacjaThis study deals with experimental and numerical investigations of elastic wave propagation in steel bars partially embedded in mortar. The bars with different bonding lengths were tested. Two types of damage were considered: damage of the steel bar and damage of the mortar. Longitudinal waves were excited by a piezoelectric actuator and a vibrometer was used to non-contact measurements of velocity signals. Numerical calculations...
-
Reduction of vibrations of steel structure models with Polymeric Bearings - experimental study
PublikacjaEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Therefore, designing earthquake protective systems has become an extremely challenging problem in civil engineering. Base isolation is one of the most popular and widely adopted methods of protecting structures against earthquake forces. The present paper reports the results obtained from the shaking table experimental...
-
Problems of collisions between adjacent steel structures under earthquake excitation
PublikacjaNowadays, the high level of urbanization forces the designers to design closely-separated structures and to take into account many factors influencing the response of these structures, which may collide due to insufficient separation distance during moderate to strong ground motions. Recent observations as well as numerical and experimental investigations have confirmed that the interactions between structures may lead to significant...
-
Ceria Based Protective Coatings for Steel Interconnects Prepared by Spray Pyrolysis
PublikacjaStainless steels can be used in solid oxide fuel/electrolysis stacks as interconnects. For successful long term operation they require protective coatings, that lower the corrosion rate and block chemical reactions between the interconnect and adjacent layers of the oxygen or the hydrogen electrode. One of the promising coating materials for the hydrogen side is ceria. Using standard sintering techniques, ceria sinters at around...
-
The Impact of Crushed Rock Spoil on Pitting Corrosion of Selected Stainless Steel
PublikacjaThe paper presents the results of the pitting resistance investigations of selected stainless steels in the chloride environment and the simultaneous impact of erosive factors using the cyclic polarization technique. Additionally, using electrochemical techniques, ie: electrochemical impedance spectroscopy (EIS) and measurement of corrosion potential, the behavior of the passive layer of selected stainless steels in the environment...
-
Numerical analysis on axial capacity of steel built-up battened columns
PublikacjaThis paper deals with the numerical analysis aimed at study the bearing capacity of pinended steel built-up columns under axial compression. Finite element (FE) models were performed for the columns presented in the literature. The main problem discussed in the article is the shape and magnitude of geometric imperfections introduced into the numerical FE model, necessary to obtain the load capacity consistent with the experimental...
-
Crack Mouth Opening Displacement for EH36 Shipbuilding Steel Measurements Dataset
PublikacjaThe dataset titled EH36 steel for shipbuilding (plate thickness 50 mm) – CMOD – force record, a0/W=0.6 contains a CMOD (Crack Mouth Opening Displacement) – Force record which is the base for evaluation of the fracture toughness of structural steel. Bend specimens with a Bx2B section (B = 50 mm), and relative initial crack length a0/W=0.60 were used. The test was carried out at ambient temperature in accordance with the ISO 12135...
-
Fatigue fracture morphology of AISI H13 steel obtained by additive manufacturing
PublikacjaThe paper focuses on researching the effect of fatigue loading on metallic structure, lifetime, and fracture surface topographies in AISI H13 steel specimens obtained by selective laser melting (SLM). The topography of the fracture surfaces was measured over their entire area, according to the entire total area method, with an optical three-dimensional surface measurement system. The fatigue results of the SLM 3D printed steel...
-
Fatigue behaviour of SLM maraging steel under variable-amplitude loading
PublikacjaOne of the most challenging issues for additive manufactured materials is fatigue endurance. Engineering components often operate under complex, variable amplitude loadings, in which existing technological imperfections promote fatigue cracks growth and damage of elements eventually. In this study the effects of different variable-amplitude strain levels on fatigue life, 18Ni300 steel was tested. The work presents various behaviours...
-
Nondestructive Characterization of 2CR-1Mo Steel Quality Using Magnetoacousting Emission
PublikacjaPrzedstawiono wyniki badań własności emisji magneto-akustycznej (EMA) oraz własności magnetycznych (pętla histerezy magnetycznej, efekt Barkhausena, magnetostrykcja) dla wycinków rur stali 2Cr-1Mo o różnym stopniu degradacji. Wykazano, iż początkowy etap degradacji skutkuje w obniżeniu natężenia EMA oraz magnetostrykcja także niewielką zmianą pola koercji i nie monotoniczną zmianą natężenia efektu Barkhausena).
-
Investigation of pitting corrosion of stainless steel by means of acousticemission and potentiodynamic methods.
PublikacjaPrzedstawiono wyniki badań korozji wżerowej przy jednoczesnym wykorzystaniu techniki potencjodynamicznej i emisji akustycznej. Dystrybuanta rozkładu prawdopodobieństwa wystąpienia korozji wżerowej (CDFp) została uzyskana na podstawie badań potencjodynamicznych. Niezależnie z wyników akustycznych otrzymano dystrybuantę rozkładu zdarzeń akustycznych (CDFae). Na podstawie wyników stwierdzono brak korelacji miedzy wynikami potencjodynamicznymi...
-
Influence of microstructure on properties of 18Cr-10Ni-Ti stainless steel products.
PublikacjaBadano wpływ mikrostruktury na właściwości mechaniczne i odporność korozyjną wyrobów ze stali austenitycznej 18Cr-10Ni-Ti po przesycaniu z temperatury 1050 C. Wykazano, że węgliki TiC w ziarnach i na granicach ziaren/bliźniaków powodują znaczne obniżenie wydłużenia stali. Węgliki TiC na granicach ziaren/bliźniaków obniżają odporność na korozję międzykrystaliczną i sprzyjają powstawaniu uszkodzeń korozyjnych podczas hutniczej operacji...
-
Research on deformations of laser-welded joint of a steel sandwich structure model.
PublikacjaPrzedstawiono problemy związane z zachowaniem złącza laserowego pod obciążeniem zginającym. Pokazano wyniki badań laboratoryjnych dla określenia mechanizmu pracy złącza i przedyskutowano uzyskane rezultaty.
-
Hydrogen assisted cracking of high-strength weldable steel in sea-water.
PublikacjaOceniono niszczenie wodorowe stali o wysokiej wytrzymałości i jej złączy spawanych przy różnych rodzajach obciążenia w wodzie morskiej. Przeprowadzono próby rozciągania z małą prędkością odkształcenia i zmęczenia niskocyklowego w wodzie morskiej przy polaryzacji katodowej. Badano stal gatunku 17HMBVA o minimalnej granicy plasyczności 690 MPa oraz jej złącza spawane automatycznie łukiem krytym i ręcznie łukowo elektrodą otuloną.
-
Influence of polyaniline primer on the corrosion properties of St3S steel - coating system
PublikacjaPraca przedstawia wyniki badań wpływu podkładu z polianiliny osadzonej elektrochemicznie na właściwości antykorozyjne powłoki epoksydowej na stali niskowęglowej St3S. Wykonano badania próbek nieuszkodzonych, a także próbek ze sztucznym defektem powłoki. Próbki były eksponowane na środowisko korozyjne przez 63 dni i były sukcesywnie badane za pomocą elektrochemicznej spektroskopii impedancyjnej. Postępy korozji były również oceniane...
-
The influence of the welding thermal cycles on corrosion resistance of duplex stainless steel
PublikacjaBadano skłonnośc strefy wpływu ciepła spoin ze stali dupleks do korozyjnego pękania narężeniowego. Wykonano próby korozyjne z wykorzystaniem metody SSRT w środowisku korozyjnym wrzącego MgCl2. Wykazano, że duży udział ferrytu w strukturze SWC pogarsza odpornośc na korozję. Badania metalograficzne na mikroskopie lektronowym wykazały różne sposoby propagacji pęknięcia zależnie od zawartości austenitu w strukturze SWC.
-
Relation between steel microstructure and its properties in inert and aggressive environments
PublikacjaBadano stale 26H2MF i 34HNM poddane różnej obróbce cieplnej. Mikrostruktury stali zmieniały sie od martenzytu i bainitu do odpuszczonego martenzytu i sorbitu. Obserwowano spadek energii zniszczenia, wydłużenia i przewżenia w próbie rozciągania z małą prędkością i równoczesnej polaryzacji katodowej do 100 mA/cm2. Degradacji towarzyszyła zmiana przełomu z ciągliwego na kruchy łupliwy i quasiłupliwy.
-
Hydrogen induced degradation of structural steel exposed to the technical liquid hydrocarbons
PublikacjaSusceptibility of the differently heat treated 26H2MF steel to stress corrosion cracking has been evaluated in the constant strain rate tension tests done at the strain rate 10-6s-1 and in the constant load tests done at the 0,98 of fracture load. The boiler fuel and the aged mineral oil at 135C and 80C respectively, have been used as the aggressive environments.
-
Mechanism of hydrogen enhanced-cracking of high-strength steel welded joints
PublikacjaPrzedstawiono badania podatności stali spawalnej o wysokiej wytrzymałości S690Q i jej złączy spawanych na niszczenie wodorowe w środowisku wody morskiej przy polaryzacji katodowej. Na podstawie wyników próby rozciągania z małą prędkością odkształcania i obserwacji przełomów próbek na SEM wskazano mechanizm pękania wspomaganego wodorem badanej stali i złączy spawanych.
-
Comparative buckling analysis of cylindrical steel silos with flat or corrugated sheets
PublikacjaW artykule zaprezentowano wyniki analizy wyboczeniowej cylindrycznych silosów wypełnionych materiałem sypkim wykonanych z blachy falistej usztywnionego słupami oraz z blachy płaskiej. Wykonano nieliniową analizę statyczną całego silosu z uwzględnieniem wstępnych imperfekcji geometrycznych przy zastosowaniu różnych przestrzennych modeli numerycznych MES. Wyniki analiza pokazują, że silosy z blachy falistej są bezpieczniejsze i bardziej...
-
Interlayer defect evolution in an organic coating system on steel under hydromechanical loading
Publikacja -
Investigation of pitting corrosion of stainless steel by means of acoustic emission and potentiodynamic methods
Publikacja