Filtry
wszystkich: 1877
wybranych: 1333
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: SCREW CONNECTON
-
An electric ring thruster as auxiliary manoeuvring propulsion system for watercraft - construction analysis
PublikacjaThe reported project aimed at examining properties and purposefulness of use of modern electromagneticbearings for a screw propeller in a prototype version of a synchronous ring motor with rare earths magnets.Bearings of this type generate electromagnetic forces which keep the rotor in a state of levitation. Therotating machine with magnetic bearings can work in any environment which reveals diamagnetic properties(air, vacuum,...
-
Development, characterization and evaluation of composite adsorbent for the adsorption of crystal violet from aqueous solution: Isotherm, kinetics, and thermodynamic studies
PublikacjaThe purpose of this work focuses on the production and investigations of a new composite material as alternative low-cost adsorbent for the removal of crystal violet (CV) dye from waste solution. The production method was performed by in-situ thermal activation technology via extrusion process of polymer wastes containing tire rubber (50 wt%) and polyurethane foam (50 wt%) using single-screw extruder under processing temperature...
-
Management of ground tire rubber waste by incorporation into polyurethane-based composite foams
PublikacjaRapid economic growth implicated the developing multiple industry sectors, including the automotive branch, increasing waste generation since recycling and utilization methods have not been established simultaneously. A very severe threat is the generation of enormous amounts of post-consumer tires considered burdensome waste, e.g., due to the substantial emissions of volatile organic compounds (VOCs). Therefore, it is essential...
-
Analysis of Residual Stresses and Dislocation Density of AA6082 Butt Welds Produced by Friction Sir Welding
PublikacjaThe Friction Stir Welding (FSW) method was employed to join AA6082 sheets. The welds were produced with different tool traverse speed (200 and 250 mm/min), rotational speed (1000 and 1250 RPM) and tool tilt angle (0 and 2 deg). Based on the analysis of XRD patterns, the total precipitation volume fractions in the nugget zones and the base material were calculated. The FSW process resulted in a reduction in the fraction of precipitates...
-
Systemy Smart Cities - studium przypadku
PublikacjaThe paper presents the architecture of an enterprise service bus used in the construction of information systems processing large amounts of data for decision-making needs at the City Hall in Gdańsk. The key concept of processes of bus development involves installation of developing environment, database connection, flow mechanisms and data presentation. The issue was supported by models such as KPI (Key Processes Identifier) and...
-
SYNTHESIS OF PHOSPHORUS TACRINE ANALOGUES AS A NEW POTENTIAL ANTI-ALZHEIMER’S DISEASE AGENTS
PublikacjaA series of novel phosphorus tacrine derivatives was obtained in three steps, including synthesis of 9-chlorotacrine, connection of 9-chlorotacrine with hexamethylenediamine, 1,8-diaminooctane and 1,12-diaminododecane linkers and reaction of obtained tacrine diamine analogues with corresponding acid ester to give nine tacrine organophosphorus compounds. All of the obtained final structures were characterized by 1H NMR, 13C NMR,...
-
CM Voltage Compensators for Power Electronic Interfaces
PublikacjaThe experimental results presented in the paper have shown that the application of the PEIs might cause EMC related problems, especially in the case of the application of a group of connected converters. The most convenient way to reduce EMI currents and prevent aggregation of EMI currents introduced by a group of converters is through passive compensation of voltage interference sources inside of the single converters. In the...
-
Recovery and re-use of photovoltaic solar cells from crystalline silicon
PublikacjaCrystalline silicon-type PV modules consist, in order of mass, of glass, an aluminium frame, an EVA coating, solar cells, a terminal box, back film and tapping screws. From the economic point of view, pure silicon, recoverable from spent cells, is the most important material owing to its cost and shortage. For crystalline, silicon-based PV cells, the following chemical treatments were performed: removal of the metal coating, followed...
-
Miniaturized Inline Bandpass Filters Based on Triple-Mode Integrated Coaxial-Waveguide Resonators
PublikacjaThis work presents a design technique to implement miniaturized cross-coupled bandpass filters in inline physical configurations based on triple-mode resonators. Triple-mode resonances are obtained by using integrated coaxial-waveguide cavity resonators. They consist of two coaxial conducting posts placed in the sidewalls of a rectangular waveguide cavity. In the proposed triplet, a transmission zero (TZ) can be positioned at any...
-
A system of visualization of operational situation on digital maps for mobile units of the Border Guards
PublikacjaBorder guards have to be equipped with technology enabling a communication, an acquisition, an exchange, and a visualization of data in different operational situations. This also applies to the staff, which is located on mobile units such as ground vehicles, aircrafts and vessels. Within the project realized for the Polish Border Guard and financed by The National Centre for Research and Development, a system was designed and...
-
Modern technologies in energy demand reducing of public transport — Practical applications
PublikacjaCity of Gdynia (Poland) exploits one of the most modern trolleybus network in Europe, which has been involved in many projects related to the reduction of energy consumption. Some of them are connected with the improving of energy breaking recovery usage. An experimental stationary storage system at Północna substation, which was tested in 2012-2014, is a bright example of a system which is connected with the improving of the...
-
Students’ soft urban planning skills and local development are the benefits from the Fair of Good Practice. Small cities - big challengesprogramme
PublikacjaThe urban planner in practice needs soft skills when dealing with public consultations connected to local development plans. To improve the abilities of architecture and urban planning students to discuss solutions and to support the development of local public spaces of small towns in the Pomeranian voivodeship ( province) in Poland, the Fair of Good Practice. Small cities - big challenges programme...
-
Four level inverter's DC bus voltage balancing with 3-terminal DAB converter
Publikacja—Multilevel inverters become more and more popular, especially in the medium or high voltage and high power applications. Unfortunately, some of inverter topologies require additional DC bus voltage balancing systems. This paper presents a novel approach to such systems, which is based on a multiple terminal DAB converter. Along with the voltage balancing function the proposed solution enables the connection of energy storage devices...
-
Modeling the Influence of Salts on the Critical Micelle Concentration of Ionic Surfactants
PublikacjaWe show for the first time that a phenomenological, augmented volume-based thermodynamics (aVBT) model is capable to predict the critical micelle concentrations of ionic surfactants, including ionic liquids, with added salts. The model also adjusts for the type of salt added by including its molecular volume, which might form a connection to the Hofmeister effect. The other physico-chemically relevant quantities included in the...
-
Application of nanofluids in selected thermal technologies
PublikacjaSome peculiarities regarding convective heat transfer of nanofluids are presented. Particularly, results of the fundamental research concerning pool boiling and single phase convection of nanofluids as well as data obtained for selected heat exchangers operated with nanofluids are discussed.
-
Knowledge‐Intensive Business Services (KIBS) and Their Role in the Knowledge‐Based Economy
PublikacjaThe importance of the knowledge‐intensive business services sector for the development of the economy is growing. In the 80s and 90s this sector became the fastest growing sector in the OECD countries (OECD, 2001). Many publications stress its close relationship to the levels of innovation and performance of the whole economy (e.g. Hipp, 1999; Tomlinson, 1999; Aslesen and Isaksen, 2007). It is an increasingly common belief that...
-
The Hopf theorem for gradient local vector fields on manifolds
PublikacjaWe prove the Hopf theorem for gradient local vector fields on manifolds, i.e., we show that there is a natural bijection between the set of gradient otopy classes of gradient local vector fields and the integers if the manifold is connected Riemannian without boundary.
-
Earthworks calculations due to reconstruction of railway geometrical layout
PublikacjaThe paper characterizes continuation of ongoing work of computer program MUGO which is connected with earthworks. The program is related to the modernization of the railway track layout. The methodology for the calculating the size of earthworks in the areas of embankments on the two way railway line is discussed in detail.
-
Assessing the Significance of Displacements Using Local Coefficients of Variance as an Alternative to the Classical Approach
PublikacjaThe safety of use of civil engineering structures remains an important issue that is approached by various sciences. Due to this fact, geodetic control measurements are conducted with the purpose of identifying threats connected with the potential displacement of structural elements. In this context, the authors discuss issues connected with determining the displacements of controlled points located in the studied object in a three-dimensional...
-
Technique to improve CMRR at high frequencies in CMOS OTA-C filters
PublikacjaIn this paper a technique to improve the common-mode rejection ratio (CMRR) at high frequencies in the OTA-C filters is proposed. The technique is applicable to most OTA-C filters using CMOS operational transconductance amplifiers (OTA) based on differential pairs. The presented analysis shows that a significant broadening of CMRR bandwidth can be achieved by using a differential pair with the bodies of transistors connected to...
-
Biophilic Design: A Trend Watch
PublikacjaDuring the 20th century, many people migrated to cities for employment and economic opportunities, abandoning farming and natural landscapes so their direct connection to the countryside and nature was lost. This process continues to this day with unprecedented urban growth, in fact, it’s estimated 68% of the world population will live in urban areas by 2050. Due to the evolutionary disposition of humans, when people live in an...
-
The determinants of the Region's and its SMEs' Competitive Position in the Context of Mega Events - the Case of the Euro 2012
PublikacjaIn this paper a modified Preuss model was used to assess the factors to enhance the competitiveness of the region and the SMEs located in the region. To accomplish the above, six types of event-structure were applied: infrastructure, knowledge, networks, culture, image and emotions. They were described in detail in reference to the case of Euro 2012 in Poland in general and Pomeranian region in particular. Finally the Authors take...
-
Mulimedia manuals for descriptive geometry and engineering graphics
PublikacjaThe article discusses issues connected with ICT (Information and Communication Technologies) implementation in Descriptive Geometry and Engineering Graphics Education. The presentation of the issues is supported by the author's multimedia manuals made in Multimedia Flash MX technology and published on the Gdańsk University of Technology net.
-
Mathematical Models of Control Systems of Angular Speed of Steam Turbines for Diagnostic Tests of Automatic and Mechatronic Devices
PublikacjaAccurate modeling of physical processes of many automatics and mechatronics systems is often necessity. In power system such a process is control of angular velocity of power objects during connection to operation in parallel. This process is extremely dynamic. For this reason response of control system depends from changes of many physical parameters (temperature, pressure and flow of the medium, etc.). Precision modeling influences...
-
Początek Gdyńskiego Systemu Wodociągowego Rozbudowa układu wodociągowego na Kępie Oksywskiej w latach 1933 - 1939. Część III.
PublikacjaBudowa sieci osiedlowej na terenie „Nowego Oksywia”. Przyłączenie wodociągu Marynarki Wojennej do budowanego układu na Kępie Oksywskiej. Komplikacje przebiegu procesu budowy rurociągu do Babiego Dołu. Uzbrojenie terenu osiedla "Paged". Przekształcenie na terenie Oksywia struktury sieci rozgałęzieniowej w pierścieniową. Konsolidacja układu na Kępie Oksywskiej z wodociągiem grupowym Wielkiej Gdyni. Realizacja zarządzenia o przymusie...
-
On-line Search in Two-Dimensional Environment
PublikacjaWe consider the following on-line pursuit-evasion problem. A team of mobile agents called searchers starts at an arbitrary node of an unknown network. Their goal is to execute a search strategy that guarantees capturing a fast and invisible intruder regardless of its movements using as few searchers as possible. We require that the strategy is connected and monotone, that is, at each point of the execution the part of the graph...
-
Method of sacrificial anode dual transistor-driving in stray current field
PublikacjaIn order to control a magnesium anode in a stray current interference field, a dual transistor driving system has been proposed. It consisted of a combination of PNP and NPN transistors. Dual transistor driven system and direct anode to cathode connection were electrochemically tested in 3% NaCl solution. The dual transistor driven system increased the anode efficiency and reduced hydrogen evolution and the risk of embrittlement....
-
Analysis of inductive power transfer systems for variable air gap and voltage supply frequency
PublikacjaThe paper describes an IPT system, by which electrical energy may be transmitted through a large air gap between coils without electrical connection. It presents theoretical and simulation analysis of IPT, which allows for supplying a receiver in the conditions of slow, in relation to the dynamics of power supply, changes in dimension of the air gap. The influence of frequency characteristics of the system on the possible selection...
-
The reliability of tree and star networks
PublikacjaThis paper investigated the reliability of tree and star networks. Following measures of network reliability are assumed: the expected number of nodes, that can communicate with the central node; the expected number of node pairs, that are connected by a path through the central node; the expected number of node pairs communicating.
-
Investigation of volatile low molecular weight compounds formed during continuous reclaiming of ground tire rubber
PublikacjaGround tire rubber was thermo-mechanically reclaimed at different temperature conditions (80, 120, 160 °C) using a co-rotating twin screw extruder. The progress of ground tire rubber reclaiming was evaluated with specific mechanical energy, sol fraction and thermogravimetric analysis. Volatile organic compounds (VOCs) including volatile sulfur compounds (VCSs) released from ground tire rubber and ground tire rubber after reclaiming...
-
The impact of filler thermomechanical modifications on static and dynamic mechanical performance of flexible foamed polyurethane/ground tire rubber/zinc borate composites
PublikacjaThe rapid development of the automotive industry is very beneficial to many aspects of human life, but it is also a very significant environmental burden. The most straightforward impact is related to the generation of exhaust, but the management of post-consumer car parts is also a major challenge. Among them, waste tires are very burdensome due to their enormous numbers. Therefore, it is essential to develop novel, environmentally...
-
Method of sacrificial anode transistor-driving in cathodic protection system
PublikacjaA magnesium anode driving system has been proposed. A PNP driving transistor has been used. Electrochemical testing in 3%NaCl, results and comparison of the driving system and classic direct anode to cathode connection are presented. The driving system reduced the protection current and stabilized the working conditions of the anode. Higher anode efficiency was achieved. Overprotection and hydrogen embrittlement threats were prevented...
-
The Concept of Geodetic Analyses of the Measurement Results Obtained by Hydrostatic Leveling
PublikacjaThe article discusses the issue of hydrostatic leveling. Its application is presented in structural health monitoring systems in order to determine vertical displacements of controlled points. Moreover, the article includes a complete computation scheme that utilizes the estimation from observation differences, allowing the elimination of the influence of individual sensors’ systematic errors. The authors suggest two concepts of...
-
Numerical analysis of the carpentry joints applied in the traditional wooden structures
PublikacjaThe paper concerns the numerical analysis of the carpentry joints made from spruce wood. The material parameters of the wood have been calculated on the basis of nine independent material constants (an orthotropic material). The contact zone between the individual elements of the connection has been determined using Contact Tables in the MSC.Marc software. Five types of carpentry joints have been analyzed. The main aim of the research...
-
System of monitoring of the Forest Opera in Sopot structure and roofing
PublikacjaThe authors present a solution realized in Forest Opera (name in Polish: Opera Leśna) in Sopot (Poland) in connection with the modernization and construction of a new roof. The complicated structure of the roof of the facility and the used covering in form of membrane made of technical fabric required (for security reasons) to install the unit of devices allowing for the continuous geodetic monitoring of the facility. Monitoring...
-
Scrutiny of power grids by penetrating PV energy in wind farms: a case study of the wind corridor of Jhampir, Pakistan
PublikacjaThis study examines the problems caused by intermittent renewable energy sources, especially wind farms, and suggests a different solar energy penetration strategy to improve their loading capacity. The study uses real-time data from a wind farm in Jhampir, Pakistan, to analyse and assess various aspects of grid stations connected to wind farms. Electrical Transient Analyzer Program is used to validate the results by linking...
-
A Wind Energy Conversion System Based on a Generator with Modulated Magnetic Flux
PublikacjaIn this work, the concept of an energy conversion system for wind turbines based on the modified permanent magnet synchronous generator (PMSG) is presented. In the generator, a pair of three-phase windings is used, one of which is connected in a “star” and the second in a “delta” configuration. At the outputs of both windings, two six-pulse uncontrolled (diode) rectifiers are included. These rectifiers are mutually coupled by a...
-
Frequency-dependent coupling model for microwave band-pass filter
PublikacjaThe goal of this work was to create a circuit model which represents frequency-dependent coupling between microwave resonators. Our models are designed for in-line filters. The frequency-dependent coupling enables one to realize a transmission zero which is not possible in classical approach with frequency independent inverters. In addition, the proposed model allows us to observe out-of-band behavior, e.g. spurious resonance....
-
Scrutiny of power grids by penetrating PV energy in wind farms: a case study of the wind corridor of Jhampir, Pakistan
PublikacjaThis study examines the problems caused by intermittent renewable energy sources, especially wind farms, and suggests a different solar energy penetration strategy to improve their loading capacity. The study uses real-time data from a wind farm in Jhampir, Pakistan, to analyse and assess various aspects of grid stations connected to wind farms. Electrical Transient Analyzer Program is used to validate the results by linking these...
-
Modern Movement in Gdynia and in Europe: Inspirations and Analogies
PublikacjaModernism in Gdynia finds its roots in the European Architecture of 1920s and 1930s. The main centres of the style are such artistic capitals as Paris, Berlin, Wien, Amsterdam, Rotterdam, Brussels, Stuttgard and Hamburg. The article points out the connections between the famous European edifeces of those times and the architecture of Gdynia.
-
Hip endhoprothesis development using rapid prototyping methods
PublikacjaIntegrated product development based on Rapid Prototyping methods, connected with computer aided 3D design and computer aided engineering enables fast and full new product verification and validation. A case study derived from clinical and technological practice using hip implant construction is also included.
-
Interpolation properties of domination parameters of a graph
PublikacjaAn integer-valued graph function π is an interpolating function if a set π(T(G))={π(T): T∈TT(G)} consists of consecutive integers, where TT(G) is the set of all spanning trees of a connected graph G. We consider the interpolation properties of domination related parameters.
-
Application of principal component and hierarchical cluster analysis in classifying defects of trolleybuses
PublikacjaThe failure rate of vehicles is a relevant task, which is strictly connected with the reliability of transportation systems. Methods of data analysis allow us to find similarity and differences between failure rates of several parts of trolleybuses. This paper deals with the statistic of failure of trolleybuses from the municipal transport company of Gdynia (Poland).
-
Verification of the method of reconstructing convective velocity fields on the basis of temperature fields in vertical, differential and equally heated, open and closed channels
PublikacjaThis paper describes a method of reconstructing velocity fields, i.e. a numerical reconstruction procedure (NRP) that involves the numerical processing of experimentally measured temperature distributions in free convection heat transfer. The NRP consists in solving only the continuity and Navier–Stokes equations with an additional source term. This term is proportional to a known temperature (e.g. from a thermal imaging camera)...
-
Computational analysis of power-law fluids for convective heat transfer in permeable enclosures using Darcy effects
PublikacjaNatural convection is a complex environmental phenomenon that typically occurs in engineering settings in porous structures. Shear thinning or shear thickening fuids are characteristics of power-law fuids, which are non-Newtonian in nature and fnd wide-ranging uses in various industrial processes. Non-Newtonian fuid fow in porous media is a difcult problem with important consequences for energy systems and heat transfer. In this...
-
UN’IPERTROFIA INEVITABILE? LA MOBILITAZIONE INDUSTRIALE E LA TRASFORMAZIONE DELL’APPARATO AMMINISTRATIVO PER LO SFORZO BELLICO
PublikacjaIl capitolo esamina le trasformazioni dell'apparato amministrativo in relazione alle esigenze dello sforzo bellico
-
Investigation of abdomen surface deformation due to life excitation: implications for implant selection and orientation in laparoscopic ventral hernia repair
PublikacjaVentral hernia is a common medical problem. Statistically there are around 10% recurrences of the sickness. The authors' former investigation proved edges of the hernia orifice displacements to be one of the factors causing recurrence. Thus, experimental investigation of the abdomen surface deformation due to some normal activities of people is studied.The extreme strains, their localization and directions are identified. The acquired...
-
Improvement of electrochemical action of zinc-rich paints by addition of nanoparticulate zinc
PublikacjaThe influence of nanosized particles on electrochemical action of standard zinc-rich paints by means of SEM as well as potential and impedance measurements has been investigated. The motivation for doing this was to obtain additional electrical connection between the spherical microparticles themselves and zinc particles and steel substrate. Overall zinc content was at the level of 92% by weight. Samples with different concentration...
-
Multimedia distributed system for visualization of ongoing and archival events for BG
PublikacjaThe paper presents concept of the distributed system designed to gather and provide the information about vehicles, vessels and airplanes present within the area of operations of the Border Guard supplemented with related multimedia. The part of the system related to the map data gathering, distribution and visualization has been already implemented in the preceding project. The presented system is the expansion of the previous...
-
Categorization of Cloud Workload Types with Clustering
PublikacjaThe paper presents a new classification schema of IaaS cloud workloads types, based on the functional characteristics. We show the results of an experiment of automatic categorization performed with different benchmarks that represent particular workload types. Monitoring of resource utilization allowed us to construct workload models that can be processed with machine learning algorithms. The direct connection between the functional...