Wyniki wyszukiwania dla: WELDQN
-
Weldability of high strength steel in underwater environment
PublikacjaThe article describes the problems with weldability of high-strength steels in the aquatic environment. The tendency of steel S355J2G3 and S500M to form cold cracks when welded in wet welding conditions has been experimentally evaluated. It was found that the tested steels have a high propensity to cracking. An experiment has been proposed and tested to evaluate the usefulness of the tempering bead technique as a method of improving...
-
Wpływ warunków zgrzewania metodą Friction Stir Welding na własności mechaniczne i jakość złączy ze stopu aluminium
PublikacjaCelem niniejszych badań było porównanie wpływu kształtu narzędzia na złącze oraz uzyskanie wartości parametrów zgrzewania tarciowego z przemieszaniem (FSW) zapewniających najlepszą możliwą jakość złącza. Zastosowanym materiałem był stop aluminium EN AW-3004 (AlMn1Mg1). Według najlepszej wiedzy autorów dotychczas nie przedstawiono żadnych badań tego stopu w kwestii zgrzewania FSW. Złącza pięcioczołowe wykonano samodzielnie opracowanym...
-
Effect of Pin Shape on Thermal History of Aluminum-Steel Friction Stir Welded Joint: Computational Fluid Dynamic Modeling and Validation
PublikacjaThis article studied the effects of pin angle on heat generation and temperature distribution during friction stir welding (FSW) of AA1100 aluminum alloy and St-14 low carbon steel. A validated computational fluid dynamics (CFD) model was implemented to simulate the FSW process. Scanning electron microscopy (SEM) was employed in order to investigate internal materials’ flow. Simulation results revealed that the mechanical work...
-
Wpływ warunków zgrzewania metodą Friction Stir Welding na własności mechaniczne i jakość złączy ze stopu aluminium
PublikacjaW prezentacji przedstawiono wyniki badań nad wpływem warunków zgrzewania metodą FSW na jakość połączeń ze stopów aluminium.
-
Influence of nodes with positive eccentricity on load-carrying capasity of truss' top chords in trusses made of welded cold-formed members.
PublikacjaIn order to establish the influence of eccentric crossing of truss members on the load-carrying capacity of the folded chord of a hat-section truss, a research model was created and preliminary numerical analysis of the truss was performed with the use of Marc Mentat programme. Distorial instability of crossheads caused by deviation of loose (unmounted) channel section web’s bends was observed. Due to the slenderness of the section’s...
-
Progress in the post weld residual stress evaluation using Barkhausen effect meter with a novel rotating magnetic field probe
PublikacjaWe report the progress in post weld residual stress evaluation using Barkhausen effect (BE) meter with rotating magnetic field probe. The novel probe of the BE meter contains two C-core electromagnets and searching coil with ferrite antenna. This meter allows automatic measurements of BE intensity envelopes at different angles of magnetizing field. The full process of measurement at given position of the probe takes about only...
-
Experimental investigation on welding of 2.25 Cr-1.0 Mo steel with regulated metal deposition and GMAW technique incorporating metal-cored wires
Publikacja -
Investigation of the Effects of Tool Positioning Factors on Peak Temperature in Dissimilar Friction Stir Welding of AA6061-T6 and AA7075-T6 Aluminum Alloys
PublikacjaAmong the emerging new welding techniques, friction stir welding (FSW) is used frequently for welding high-strength aluminum alloys that are difficult to weld by conventional fusion-welding techniques. This paper investigated the effects of tool-positioning factors on the maximum temperature generated in the dissimilar FSW joint of AA6061-T6 and AA7075-T6 aluminum alloys. Three factors of plunge depth, tool offset, and tilt angle...
-
Laser Welding of UNS S33207 Hyper-Duplex Stainless Steel to 6061 Aluminum Alloy Using High Entropy Alloy as a Filler Material
PublikacjaThe high entropy alloy (HEA) filler used during the fabrication method determines the reliability of HEAs for steel-aluminum dissimilar alloy configuration. HEAs have a direct impact on the formation of intermetallic compounds (IMC) formed by the interaction of iron (Fe) and aluminum (Al), and influence the size of the joint’s interaction zone. A novel welding process for Fe-Al alloy joints was developed to prevent the development...
-
Influence of PWHT Parameters on the Mechanical Properties and Microstructural Behavior of Multi-Pass GTAW Joints of P92 Steel
PublikacjaThe 9% Cr steels were developed for ultra-supercritical (USC) power plants to meet the requirements of high operating temperature and pressure. These steels are produced to operate at high temperatures where impact toughness is not a concern; however, it becomes important for the welded joints to have good impact toughness at room temperature for manufacturing. The present work investigates the effect of the post-weld heat treatment...
-
Comparison of strain results at a laser weld notch obtained by numerical calculations and experimental measurements
PublikacjaIn the development of ship structures applying new materials and it’s purposeful placement play an important role. During the last years, especially in a construction of ro-ro type vessels, the usage of novel sandwich structures in cargo decks is profitable. Steel sandwich panel is an innovative solution which at a todays state of development can be used for the construction of any members not taking part in a global bending of...
-
Daniel Chuchała dr hab. inż.
Osoby -
Microstructure and mechanical properties of a dissimilar metal welded joint of Inconel 617 and P92 steel with Inconel 82 buttering layer for AUSC boiler application
PublikacjaThe application of the novel dissimilar metal welded (DMW) joint, utilizing Inconel 617 and P92 steel, was showcased in the advanced ultra-supercritical (AUSC) boiler. The work has been performed to investigate the effect of Inconel 82 (ERNiCr-3) buttering layer on microstructure and mechanical properties (high-temperature tensile strength, impact strength and microhardness) of gas tungsten arc welded (GTAW) dissimilar joint between...
-
Obliczanie czasów chłodzenia spawanych łukowo złączy stali odpornych na korozję = Cooling times calculation for stainless steels arc welded joints.
PublikacjaPrzedstawiono wpływ właściwości cieplnych i parametrów spawania stali odpornych na korozję na czas chłodzenia złącza w zakresie temperatur 800-500oC. Przedstawiono analityczne obliczenia tego czasu. W oparciu o wyniki badań rzeczywistych cykli cieplnych spawania stali typu duplex 2205 opracowano wzór do obliczania czasów chłodzenia złącza 800-500 C.
-
The Influence of Selected Parameters of Numerical Modelling on Strains and Stresses at Weld Toe Notch
PublikacjaLatest development in the field of welding technology and prefabrication enabled massive production of thin-walled sandwich structures. Multi-layered sandwich structures are fabricated with the use of high-power CO2 lasers, friction welding, arc welding, hybrid welding, or other technique designed for the special purpose. Steel or aluminium alloy plates with thickness between 1 and 5 mm are connected by internal stiffeners. Strength...
-
High-Temperature Tensile Behaviour of GTAW Joints of P92 Steel and Alloy 617 for Two Different Fillers
PublikacjaThis study explores the high-temperature (HT) tensile rupture characteristics of a dissimilar gas-tungsten-arc-welded (GTAW) joint between P92 steel and Alloy 617, fabricated using ER62SB9 and ERNiCrCoMo-1 fillers. The high-temperature tensile tests were performed at elevated temperatures of 550 ◦C and 650 ◦C. An optical microscope (OM) and a field emission scanning electron microscope (FESEM) were utilized to characterize the...
-
Preliminary investigations of effect of conditions of FCAW process on diffusible hydrogen content in deposited metal
PublikacjaOne of the types of hydrogen degradation of steel welded joints is cold cracking. The direct cause of the formation of cold cracks is simultaneous presence of hydrogen, residual stresses and brittle structure. The way of preventing the occurring of degradation is to eliminate at least one of these factors. Practice has shown that the best solution is to control the amount of hydrogen in deposited metal. In this paper the state...
-
Prognozowanie właściwości złączy spawanych pod wodą metodą lokalnej komory suchej
PublikacjaNiniejsza praca jest poświęcona spawaniu pod wodą metodą lokalnej komory suchej (MLKS) i przedstawia metodologię oraz narzędzia umożliwiające prognozowanie właściwości złączy spawanych wykonanych przy zastosowaniu tej odmiany spawania. Monografia zawiera opis rozwoju spawania pod wodą oraz charakterystykę metod wykorzystywanych do realizacji prac spawalniczych. Zaproponowano nowy podział metod spawania pod wodą, uwzględniający...
-
Wstępne badania technologii spawania złączy narożnych ze stali niskoweglowej i nierdzewnej o grubości g=6mm i g=10mm
PublikacjaCelem pracy był dobór parametrów spawania dla spoin narożnych o grubości 6mm i 10mm próbek wykonanych ze stali niskowęglowej S355 i stali nierdzewnej - typu 304 (X6CrNI18-10). Złącza były spawane laserowo, jednostronnie z pełnym przetopem a powierzchnie lica i grani zapewniają uzyskanie szczelności przylegającego elementu uszczelniającego. Próbki zostały dostarczone przez Zleceniodawcę. Próby zostały przeprowadzone na stanowisku...
-
A dissimilar welded joint of grade 92 steel and AISI 304L steel obtained using IN82 buttering and IN617 fller: relationship of microstructure and mechanical properties
PublikacjaUnfavourable operating conditions of equipment in the energy industry resulting from high-temperature loads determine the need to use special materials and technological solutions, including welding procedures. In this article, buttering using IN82 (ERNiCr-3) consumables was proposed as a method to improve the weldability of grade 92 steel joined by the gas tungsten arc welding (GTAW) process with AISI 304L (IN617 fller). The...
-
Determination of causes of accelerated local corrosion of austenitic steels in water supply systems
PublikacjaThis paper concerns an inspection of a water supply system, made of AISI 304 steel, which showed signs of local corrosion at the weld. Such corrosion caused material perforation after very short periods of operation. It was revealed that steel was sensitised during the welding process. It was also proven that chromium micro-segregation occurred in the alloy leading to galvanic cell formation which initialised the process of pitting...
-
Failure of austenitic stainless steel tubes during steam generator operation
PublikacjaThe article presents the failure process of austenitic stainless steels used in power devices, such as heat exchangers, steam generators, in terms of local corrosion: pitting, stress and intergranular corrosion, paying particular attention to welded joints area. The effect of steel chemical composition, microstructure, welding process and work environment was analyzed. The second part of the article presents the results of the...
-
Fatigue life improvement using low transformation temperature weld material with measurement of residual stress
PublikacjaWelding processes often produce high levels of tensile residual stress. Low transformation temperature (LTT) welding wires utilise phase transformation strains to overcome the thermal contraction of a cooling weld. In this paper, the residual stress within each weld was quantified using the milling/strain gauge method, being the strain change measured as the weldment was milled away. The fatigue tests were conducted under uniaxial...
-
Corrigendum to “Fatigue life improvement using low transformation temperature weld material with measurement of residual stress” [Int. J. Fatigue 164 (2022) 107137]
PublikacjaWelding processes often produce high levels of tensile residual stress. Low transformation temperature (LTT) welding wires utilise phase transformation strains to overcome the thermal contraction of a cooling weld. In this paper, the residual stress within each weld was quantified using the milling/strain gauge method, being the strain change measured as the weldment was milled away. The fatigue tests were conducted under uniaxial...
-
Stalowe panele sandwicz - nowe możliwości wynikające z zastosowania spawania laserowego = All steel sandwich panels - new possibilities introduced by laser welding techniques
PublikacjaW artykule przedstawiono podstawowe dane na temat stalowych paneli typu sandwicz i technik ich wykonywania. Złącze takie charakteryzuje się specyficznymi własnościami, zdecydowanie odmiennymi od klasycznego połączenia spoiną pachwinową, którego cechy wytrzymałościowe i technologiczne są już dobrze opanowane. W podsumowaniu wykazano, że modelowanie jego geometrii musi być prowadzone na znacznie większym poziomie szczegółowości ze...
-
Reduction of Derivative pipeline effort in water turbine
PublikacjaThe paper presents an approach to evaluate and reduce the effort of the derivative pipeline in a water turbine of a hydrostatic power station in its vulnerable spots. Potential places of the biggest effort of the structure, as well as the coefficient of displacement and safety factor related to them were identified using FEM numerical method. Pipeline reinforcement was designed and made based on FEM analysis. Original technology...
-
Effect of the Post-Weld Surface Condition on the Corrosion Resistance of Austenitic Stainless Steel AISI 304
PublikacjaSurfaces of welded elements made of corrosion-resistant (stainless) steels develop temper colours. The removal of thickened oxide layers off steels exposed to temperatures below 300°C is necessary and entails the restoring of high corrosion resistance of the stainless steel. The article presents tests concerned with the effect of a method applied to remove post-weld temper on the corrosion resistance of austenitic stainless steel...
-
Effect of Porosity on the Thermo-Mechanical Behavior of Friction-Stir-Welded Spark-Plasma-Sintered Aluminum Matrix Composites with Bimodal Micro- and Nano-Sized Reinforcing Al2O3 Particles
PublikacjaThe thermo-mechanical behavior of nanosized Al2O3 particles reinforcing aluminum was analyzed in the present paper. The material was prepared by spark plasma sintering and friction stir welding. The thermal stresses affecting the composite behavior during welding were modeled through COMSOL MultiPhysics, and the results were validated by the analyses of the composites’ mechanical properties. The spark-plasma-sintered materials...
-
Application of Barkhausen method to determine internal stresses in cold-rolled and hot-rolled sheets
PublikacjaThe paper presents investigations on internal stress distribution in plane hot—or cold-rolled sheets dedicated for the cold-formed profiles. The motivation of the research is a new profile design whose bending technology, incorporating a longitudinal welded joint and hot-dip galvanization after bending and welding introduces additional internal stresses. In order to identify the entirety of stresses in the process of sheet production...
-
Annals of "Dunarea de Jos" University of Galati, Fascicle XII, Welding Equipment and Technology
Czasopisma -
Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses
PublikacjaWire arc additive manufacturing (WAAM) is an additive manufacturing process based on the arc welding process in which wire is melted by an electric arc and deposited layer by layer. Due to the cost and rate benefits over powder-based additive manufacturing technologies and other alternative heat sources such as laser and electron beams, the process is currently receiving much attention in the industrial production sector. The gas...
-
Analytical method of determining dynamic properties of thermocouples used in measurements of quick – changing temperatures of exhaust gases in marine diesel engines
PublikacjaThe article presents selected issues of mathematical modeling of heat exchange between the thermocouple and the exhaust gas flowing them, in unsteady conditions. On the way of energy balancing consideration of thermodynamic processes developed differential equations describing the dynamic properties for three versions of the design sheathed thermocouples: with weld isolated from the sheath, with weld welded the sheath and with...
-
Opracowanie procedury i badania wytrzymałościowe połączeń spawanych pomiędzy rurą kwadratowa a elementami giętymi na zimno ze stali S355 oraz testowanie połączeń o grubości 4, 6, 8mm typu S355
PublikacjaCelem pracy było: - opracowanie procedury badania wytrzymałości połączeń spawanych rozciąganych w kierunku prostopadłym i w kierunku równoległym (ścinanych) do osi spoiny. Spoiny te łączyły elementy rur kwadratowych o różnej grubości z elementami w kształcie ceownika giętymi na zimno. - wykonanie próbek do badań wytrzymałościowych wyciętych z elementów spawanych dostarczonych przez Zakład Produkcyjny firmy Borga obciążonych prostopadle...
-
Effect of processing parameters on the cyclic behaviour of aluminium friction stir welded to spark plasma sintered aluminium matrix composites with bimodal micro-and nano-sized reinforcing alumina particles
PublikacjaUnderstanding the cyclic behaviour of Alumina reinforced Aluminium composites (Al-A2O3) was of critical importance, for their further application in the different industrial sectors. The present study is focussing on the cyclic behaviour of the Al-Alumina nanocomposite produced through the combination of spark plasma sintering (SPS) method and friction stir welding (FSW). The added Alumina with total content of 10% is the combination...
-
Tytanowa międzywarstwa w łącznikach do spawania Al i stopów AlMg ze stalą=Titanium interlayer in transition joints to welding aluminium and aluminium alloys AlMg with steel
PublikacjaPrzedstawiono idee stosowania łączników i ich wytwarzanie oraz własności i niedostatki obecnie stosowanych łączników. Zaprezentowano wyniki prób technologicznych wytwarzania oraz wyniki badań mechanicznych i strukturalnych trójwarstwowego łącznika stal-tytan-aluminium.
-
Wpływ rodzaju zanieczyszczenia powierzchni odlewu ze staliwa LH14 na jakość napoin wykonanych elektrodą otuloną
PublikacjaNapawanie jest szeroko stosowaną metodą naprawiania powierzchni. Pozwala między innymi na uzupełnienie miejsc, w których uprzednio wystąpiły wżery korozyjne. Techniki napawania wykorzystywane są również do przywracania pierwotnego kształtu zużytych części. W pracy wykonano badania napoin wykonanych elektrodami otulonymi na czołowych powierzchniach cylindrycznych próbek ze staliwa LH14. Proces wykonywano dwoma rodzajami elektrod:...
-
Trwałość spawanych instalacji wodnych wykonanych z nierdzewnych stali austenitycznych
PublikacjaW artykule przedstawiono dwa przypadki przedwczesnych uszkodzeń spawanych instalacji wodnych wykonanych ze stali odpornych na korozję. W celu ustalenia przyczyn uszkodzenia instalacji przeprowadzono badania metalograficzne, makro - i mikroskopowe oraz mikroanalizę składu chemicznego EDS na próbkach pobranych z reprezentatywnych miejsc. Wykazano, że głównymi przyczynami awarii rurociągów wody pitnej były niezgodności spawalnicze,...
-
Identification of intermetallic phases in the structure of austenitic steel with use of Scanning Kelvin Probe Microscopy
Dane BadawczeDelta ferrite is formed in austenitic steels during the solidification of the alloy and its welds. It can also occur as a stable phase in any temperature range in high-alloy austenitic-ferritic steels. Depending on the amount, it can change into gamma and sigma phases and into ferrite with variable chromium content. The main role of delta ferrite in...
-
Zgrzewanie tarciowe z mieszaniem wewnętrznym zgrzeiny stopów aluminium AW7075-T651 i AW6082-T6 = Friction stir welding of aluminium alloys AW-7075-t651 and AW-6082-t6
PublikacjaW pracy przedstawione są wyniki badań nad złączami doczołowymi zgrzewanymi przy użyciu technologii Friction Stir Welding (FSW), wykonanymi z wysokowytrzymałego stopu Al-Zn (AW-7075-T651) oraz stopu Al-Mg2Si (AW-6082-T6) o wysokiej odporności na korozję. Stop AW-7075-T651 okazał się bardziej podatny na obniżenie własności mechanicznych w odniesieniu do materiału rodzimego. Złącza ze stopu AW-6082-T6 wykazały się lepszą plastycznością....
-
Badania spawalności stali S460N w środowisku wodnym z wykorzystaniem próby Tekken
PublikacjaSpawanie w środowisku wodnym niesie ze sobą wiele problemów, wśród których najważniejszym jest skłonność stali do powstawania pęknięć zimnych. O ile w przypadku spawania na powietrzu istnieje wiele metod zapobiegania tym pęknięciom, o tyle pod wodą zastosowanie tych metod jest ograniczone. Z tego powodu konieczne jest określenie skłonności danego materiału do pękania zimnego. W pracy oceniono spawalność drobnoziarnistej...
-
Opracowanie technologii spawania naprawczego szyn poddźwigowych A120 oraz badania nieniszczące jakości szyn w DCT w Porcie Północnym
PublikacjaEkspertyza dotyczy realizacji zlecenia związanego z naprawą spoin szyn poddźwigowych na terenie terminalu kontenerowego - Deep Water Terminal (DCT) w Porcie Północnym w Gdańsku. W ramach opracowania: 1. Wykonano badania ultradźwiękowe (UT) i magnetyczno-proszkowe (MT) spoin czołowych szyn poddźwigowych typu A120, według schematu dostarczonego przez firmę SKANSKA S.A. 2. Wykonano analizę wyników badań...
-
Tensile curve of E grade steel for shipbuilding
Dane BadawczeIn the shipbuilding industry, the risk of brittle fractures developing in constructions is limited by employing certified materials of specific impact strength, determined using the Charpy method (for a given design temperature) and by exercising control over the welding processes (technology qualification, supervision of production, tests of non-destructive...
-
Application of the Barkhausen effect probe with adjustable m agnetic field direction for stress state determination in the P91 ste el pipe
PublikacjaThe paper presents the results of application of a novel Barkhausen effect (BE) probe with adjustable magnetizing field direction for the stress level evaluation in ferromagnetic materials. The investigated sample was in a form of a pipe, made of P91 steel that was anisotropic due to the production process. The measurements were performed before and after welding, revealing the influence of welding process on the residual stress...
-
Janusz Kozak prof. dr hab. inż.
OsobyDr hab. inż. Janusz Kozak Dziekan Wydziału Oceanotechniki i Okrętownictwa Politechniki Gdańskiej Urodzony: 04.07.1953 w Pucku Absolwent Technikum Budowy Okrętów „Conradinum” w Gdańsku, 1973. Absolwent Instytutu Okrętowego PG, 1978. Po ukończeniu studiów praca w Stoczni Gdynia, a od roku 1980 w Katedrze Technologii Okrętów Instytutu Okrętowego a później Wydziału Oceanotechniki i Okrętownictwa Politechniki Gdańskiej kolejno na...
-
Opracowanie technologii naprawy nieciągłości metalicznych w połączeniach spawanych, w konstrukcji podpór przednich pras filtracyjnych położonych na terenie Grupowej Oczyszczalni Ścieków Dębogórze
PublikacjaCelem niniejszej pracy jest opracowanie wytycznych technologicznych, których wdrożenie pozwoli na usunięcie istniejących pęknięć, co przyczyni się do stabilizacji wymiarowej podpór oraz całej konstrukcji pras. Osiągniecie tego celu wymaga podjęcia następujących działań: - ocenę stanu technicznego naprawianego komponentu- podpór przednich trzech pras filtracyjnych, - określenie własności spawalniczych materiału naprawianego, -...
-
The effect of numerical 2D and 3D FEM element modelling on strain and stress distributions at laser weld notches in steel sandwich type panels
PublikacjaLike other means of transport, merchant ships face the problem of increasing requirements concerning the environment protection, which, among other issues, implies the reduction of fuel consumption by the ship. Here, the conventional approach which consists in making use of higher strength steels to decrease the mass of the ship hull can be complemented by the use of new steel structures of sandwich panel type. However, the lack...
-
Joints Of Steel Sandwich Structures
PublikacjaSteel sandwich structures are perceived as alternatives to single-skin welded structures in the shipbuilding industry due its advantages like significant reduction of mass in relation to typical single skin structure. However, beside problems with their strength properties itself, applications in real structures requires of solving the problem of joining, both for connection sandwich to sandwich as well as sandwiches to single-shell...
-
Weldability of pipe grade polyethylenes as realized from thermal and mechanical properties assessments
PublikacjaSince polyethylene (PE) has been widely accepted for the production of high-pressure fluid conveying pipelines, studies devoted to weldability of PE connections were always of major importance. In this study, two industrial PE grades designed for pipe production, namely PE80 and PE100, were injection molded, cut, and then welded as PE100-PE100, PE100-PE80, and PE80-PE80. The heat-welded joints were assessed by differential scanning...
-
Karol Niklas dr hab. inż.
OsobyKarol NIKLAS jest adiunktem w Wydziale Inżynierii Mechanicznej i Okrętownictwa Politechniki Gdańskiej . Pracę dyplomową magisterską na kierunku "Budowy okrętów morskich" w specjalności "Budowa małych statków i jachtów" obronił w 2007 roku. W 2008 roku ukończył studia podyplomowe w specjalności "Nowoczesne Metody Symulacyjne w Technice" na Wydziale Fizyki i Matematyki Stosowanej. W 2014 roku obronił rozprawę doktorską pt. "Zastosowanie...
-
A fast procedure of stress state evaluation in magnetically anisotropic steels with the help of a probe with adjustable magnetizing field direction
PublikacjaThe paper presents a novel approach to the stress state evaluation issue. It deals with a strongly (magnetically) anisotropic materials for which a direct interpretation of the Barkhausen effect (BE) intensity would lead to erroneous results. In such a case one has to take into account both the measured BE intensity and the orientation of the magnetisation direction relative to the magnetic easy axis. For the in plane stress distribution...