wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: TRANSPARENT COATINGS
-
Interlayer defect evolution in an coating system on steel under hydromechanical loading
PublikacjaZaprezentowano wyniki pomiarów impedancyjnych obszaru międzywarstwowego w systemie powłokowym poddanym naprężeniom. Przedstawiono nowy sensor który jest zdolny do detekcji defektów w obszarze międzywarstwowym. Dwuwarstwowy system powłokowy przeznacziony do zastosowań morskich zbadano w celu określenia jego odporności na oddziaływanie cyklicznych naprężeń i zanurzeń w 3% roztworze NaCl.
-
Effect of Coating Material Properties on Tilting-pad Thrust Bearing Performance
PublikacjaPolymer lined tilting-pad bearings demonstrate many advantages over traditional bearing systems. Bearings with a polymer layer in comparison with a babbitted layer show, for example: lower value of friction coefficient (important during start/stops), higher fatigue strength of the coating, better distribution of the load on individual pads due to lower elasticity of the polymers, wider range of operational temperatures or the ability...
-
Aplication of impedance imaging to evaluation of organic coating degradation at a local scale
PublikacjaZaproponowano nowe podejście do oceny lokalnych właściwości elektrycznych powłok organicznych. Wykorzystuje ono mikroskop sił atomowych pracujący w trybie kontaktowym. Pomiędzy igłę mikroskopu i podłoże metalowe pokryte powłoką przykładany jest sinusoidalny napięciowy sygnał pobudzenia o zadanej częstotliwości i mierzony jest prądowy sygnał odpowiedzi. Zalety tego podejścia zostały zaprezentowane na przykładzie powłoki akrylowej...
-
Structure of sol-gel derived Nb2O5 films for active coating devices
PublikacjaW artykule przedstawiono wyniki badań struktury cienkich warstw nb2o5 otrzymywanych metodą zol-żel. wytworzone warstwy charakteryzowano pod kątem zastosowania jako materiałów na aktywne pokrycia fotoniczne.
-
Effect of electrode waterproof coating on quality of underwater wet welded joints
PublikacjaIn this paper, the effects of different hydrophobic coatings on the surface of covered electrodes on the quality of wet welded carbon steel joints were discussed. Commonly available hydrophobic substances used in industrial applications were selected for the research. The aim of using waterproof coatings was to check the possibility to decreasing the susceptibility of highstrength low-alloy S460N steel to cold cracking. During...
-
Effect of interconnect coating procedure on solid oxide fuel cell performance
PublikacjaChromium (Cr) species vaporizing from chromia-forming alloy interconnects is known as a source of degradation in solid oxide fuel cell (SOFC) stacks called “cathode poisoning”. (Mn,Co)3O4 spinel coatings offer good protection against Cr evaporation during operation. In this study, Crofer 22 APU steel interconnects were electrophoretically deposited in different mediums to obtain high packing of green coating layer. The optimized...
-
Novel application of dynamic electrochemical impedance monitoring to a cataphoretic coating process
PublikacjaThe paper presents a novel method of on-line impedance monitoring of cataphoretic coating application process. Utilization of dynamic electrochemical impedance spectroscopy (DEIS) overcame the fundamental problem connected with non-stationarity of the aforementioned coating deposition process, which eliminates classical impedance spectroscopy technique from a real-time description of cataphoresis. The paper illustrates selected examples...
-
In Vitro Biological Characterization of Silver-Doped Anodic Oxide Coating on Titanium
PublikacjaDespite the high biocompatibility and clinical effectiveness of Ti-based implants, surface functionalization (with complex osteointegrative/antibacterial strategies) is still required. To enhance the dental implant surface and to provide additional osteoinductive and antibacterial properties, plasma electrolytic oxidation of a pure Ti was performed using a nitrilotriacetic acid (NTA)-based Ag nanoparticles (AgNP)-loaded calcium–phosphate...
-
Characteristics of silver-dopped carbon nanotube coating destined for medical applications
PublikacjaCarbon nanotubes are materials demonstrating outstanding mechanical, chemical, and physical properties and are considered coatings of titanium implants. The present research is aimed to characterize the microstructure and properties of the multi-wall carbon nanotubes (MWCNTs) layer decorated with silver nanoparticles (Ag NPs) on the Ti13Nb13Zr alloy destined for long-term implants. The electrophoretic deposition of coatings...
-
Effect of laser heating on cavitation behaviour of Fe-Cr-Mn coating.
PublikacjaW pracy przedstawiono badania odporności kawiracyjnej napoiny Fe-Cr-Mn po obróbce laserowej polegającej na przetapianiu napoiny wiązką lasera CO2 o mocy 1000W oraz jej nagrzewaniu w stanie stałym. Rezultaty badań wskazują,że po każdym rodzaju obróbki występuje inna podatność obrobionej powierzchni do odkształceń plastycznych pod działaniem obciążeń kawitacyjnych.
-
Influence of polyaniline primer on the corrosion properties of St3S steel - coating system
PublikacjaPraca przedstawia wyniki badań wpływu podkładu z polianiliny osadzonej elektrochemicznie na właściwości antykorozyjne powłoki epoksydowej na stali niskowęglowej St3S. Wykonano badania próbek nieuszkodzonych, a także próbek ze sztucznym defektem powłoki. Próbki były eksponowane na środowisko korozyjne przez 63 dni i były sukcesywnie badane za pomocą elektrochemicznej spektroskopii impedancyjnej. Postępy korozji były również oceniane...
-
Quantification of interlayer adhesion in protective coating systems using impedance spectroscopy
PublikacjaNowoczesne systemy powłokowe stosowane w praktyce są wielowarstwowe. Potencjalnie słabymi obszarami z punktu widzenia właściwości ochronnych są obszary międzywarstwowe. Osiągnięcie odpowiedniej przyczepności pomiędzy warstwami pozwala na polepszenie zdolności ochronnych całego zestawu. Tradycyjne metody pomiaru adhezji międzywarstwowej są destrukcyjne. Zaproponowano nową metodę oceny przyczepności międzywarstwowej przy użyciu...
-
Impedance-based sensing of the interlayer adhesion loss in organic coating systems.
PublikacjaZmienne parametry środowiska takie jak: temperatura,wilgotność i promieniowanie UV powodują degradację własności ochronnych powłok organicznych. Stosując sensor w postaci elektrod wykonanych z prądoprzewodzącego tuszu umieszczonych pomiędzy warstwami zestawu oraz technikę spektroskopii impedancyjnej stwierdzono możliwość monitorowania utraty adhezji międzywarstwowej.
-
In-situ Cu-doped MnCo-spinel coatings for solid oxide cell interconnects processed by electrophoretic deposition
PublikacjaThe Cu doping of the Mn–Co spinel is obtained “in-situ” by electrophoretic co-deposition of CuO and Mn1.5Co1.5O4 powders and subsequent two-step reactive sintering. Cu-doped Mn1.5Co1.5O4 coatings on Crofer22APU processed by electrophoretic co-deposition method are tested in terms of long term oxidation resistance and area specific resistance tests up to 3600 h. The introduction of Cu in the spinel lead to higher level of densification...
-
In Vitro Studies on Nanoporous, Nanotubular and Nanosponge-Like Titania Coatings, with the Use of Adipose-Derived Stem Cells
PublikacjaIn vitro biological research on a group of amorphous titania coatings of different nanoarchitectures (nanoporous, nanotubular, and nanosponge-like) produced on the surface of Ti6Al4V alloy samples have been carried out, aimed at assessing their ability to interact with adipose-derived mesenchymal stem cells (ADSCs) and affect their activity. The attention has been drawn to the influence of surface coating architecture and its physicochemical...
-
Tribological and thermal behavior with wear identification in contact interaction of the Ti6Al4V-sintered carbide with AlTiN coatings pair
Publikacja -
The Effect of Long-Term Annealing on Microstructure of Aluminide Coatings Deposited on MAR M200 Superalloy by CVD Method
Publikacja -
Thermal Barrier Stability and Wear Behavior of CVD Deposited Aluminide Coatings for MAR 247 Nickel Superalloy
Publikacja -
The Effect of Sodium Tetrafluoroborate on the Properties of Conversion Coatings Formed on the AZ91D Magnesium Alloy by Plasma Electrolytic Oxidation
Publikacja -
Improved mechanical properties of W-Zr-B coatings deposited by hybrid RF magnetron – PLD method
Publikacja -
Thermal and mechanical properties of (W,Zr)B2-z coatings deposited by RF magnetron sputtering method
Publikacja -
Electrical conductivity of NbN-SiO2 films obtained by ammonolysis of Nb2O5-SiO2 sol-gel derived coatings
PublikacjaW pracy przedstawiono badania przewodnictwa elektrycznego (w zakresie 5-280K) warstw NbN-SiO2 o grubości 450 nm. Warstwy uzyskano poprzez azotowanie otrzymanych metodą zol-żel warstw Nb2O5-SiO2, o różnym stosunku molowym Nb2O5/SiO2. Azotowanie takich warstw w temperaturze 1200C prowadzi do otrzymania metalicznych granul NbN w amorficznej matrycy SiO2. Struktura warstw była badana mikroskopem sił atomowych (AFM) oraz metodą dyfrakcji...
-
The Effect of Recycled Fine Aggregate Sourced from Construction and Demolition Waste on the Properties of Epoxy Resin Coatings
Publikacja -
Fabrication of Paper Sheets Coatings Based on Chitosan/Bacterial Nanocellulose/ZnO with Enhanced Antibacterial and Mechanical Properties
Publikacja -
Fabrication of Paper Sheets Coatings Based on Chitosan/Bacterial Nanocellulose/ZnO With Enhanced Antibacterial and Mechanical Properties
Publikacja -
Effect of plasma sprayed and laser re-melted Al2O3 coatings on hardness and wear properties of stainless steel
PublikacjaCommercially available austenic stainless steel substrate was coated with commercially available, raw Al2O3 powder applied by means of plasma spraying method and then re-melted with CO2 laser beam of various parameters. Tribological and mechanical properties of the 120 J/mm and 160 J/mm laser re-melted coatings were compared with the tribological and mechanical properties of the “as-sprayed” coating. The influence of the laser...
-
Porous material-based sorbent coatings in Solid-phase microextraction technique: Recent trends and future perspectives
PublikacjaThe use of porous materials as sorbents in sample preparation techniques has gained recent scientific attention in the context of developing novel fibers for the Solid-phase microextraction (SPME) technique. SPME requires the appropriate selection of a robust sorbent for successful utilization under variable conditions. A deeper understanding of the nature of newly developed porous SPME coatings and the impact of their structures...
-
Microstructure and Properties of Electroless Ni-P/Si3N4 Nanocomposite Coatings Deposited on the AW-7075 Aluminum Alloy
PublikacjaThe article presents the results of mechanical and tribological tests of Ni-P/Si3N4 nanocomposite coatings deposited on the AW-7075 aluminum alloy using the chemical reduction method. The influence of the chemical composition on the Vickers microhardness determined by the DSI method was examined. The nanocomposite layers were made of Si3N4 silicon nitride in a polydisperse powder with a particle size ranging from 20 to 25 nm. The...
-
Fe-modified Mn2CuO4 spinel oxides: coatings based on abundant elements for solid oxide cell interconnects
PublikacjaThe current state of the art steel interconnect coating materials are based on critical raw material - Co-oxide spinels. Replacing Co-oxide spinels with alternative, abundant materials can reduce the dependence on the critical raw materials. Cobalt-free coatings with the general formula Mn2-xCuFexO4, where x = 0, 0.1, 0.3, were electrophoretically deposited on a ferritic stainless-steel support and evaluated. Prior to deposition,...
-
Biological and antibacterial properties of chitosan-based coatings with AgNPs and CuNPs obtained on oxidized Ti13Zr13Nb titanium alloy
PublikacjaDespite numerous studies, the antibacterial efficiency and cytotoxicity of chitosan-based coatings with nanometals need further studies. The purpose of this research was to determine the biological properties of chitosan coatings implemented with either silver nanoparticles (AgNPs) or copper nanoparticles (CuNPs), that were electrophoretically deposited on electrochemically oxidized Ti13Zr13Nb alloy. The SEM tests were used to...
-
The Effect of Sodium Tetrafluoroborate on the Properties of Conversion Coatings Formed on the AZ91D Magnesium Alloy by Plasma Electrolytic Oxidation
PublikacjaMagnesium and its alloys are widely used in many areas because of their light weight, excellent dimensional stability, and high strength-to-weight ratio. However, the material exhibits poor wear and corrosion resistance, which limits its use. Plasma electrolytic oxidation (PEO) is an effective surface modification method for producing ceramic oxide layers on Mg and their alloys. The influence of the additions of sodium tetrafluoroborate...
-
Electrochemically assisted deposition of hydroxyapatite on Ti6Al4V substrates covered by CVD diamond films — Coating characterization and first cell biological results
PublikacjaAlthough titaniumand its alloys are widely used as implant material for orthopedic and dental applications they show only limited corrosion stability and osseointegration in different cases. The aim of the presented research was to develop and characterize a novel surface modification system from a thin diamond base layer and a hydroxyapatite (HAp) top coating deposited on the alloy Ti6Al4V widely used for implants in contact with bone....
-
High-temperature oxidation of the Crofer 22 H ferritic steel with Mn1.45Co1.45Fe0.1O4 and Mn1.5Co1.5O4 spinel coatings under thermal cycling conditions and its properties
PublikacjaThe aim of the presented study was to deposit protective-conducting Mn1.45Co1.45Fe0.1O4 and Mn1.5Co1.5O4 spinel coatings on the Crofer 22 H ferritic steel by means of electrophoresis and to evaluate their physicochemical properties after high-temperature oxidation under thermal cycling conditions. When the Crofer 22 H steel – whether uncoated or coated with the two spinels – was oxidized in 48-h cycles involving a temperature of...
-
Low temperature processed MnCo2O4 and MnCo1.8Fe0.2O4 as effective protective coatings for solid oxide fuel cell interconnects at 750 °C
PublikacjaIn this study two materials, MnCo2O4 and MnCo1.8Fe0.2O4 are studied as potential protective coatings for Solid Oxide Fuel Cell interconnects working at 750 °C. First powder fabrication by a modified Pechini method is described followed by a description of the coating procedure. The protective action of the coating applied on Crofer 22 APU is evaluated by following the area specific resistance (ASR) of the scale/coating for 5500...
-
Protective properties of Al2O3 + TiO2 coating produced by the electrostatic spray deposition method
PublikacjaMechanical resistance of Al2O3 + TiO2 nanocomposite ceramic coating deposited by electrostatic spray deposition method onto X10CrAlSi18 steel to thermal and slurry tests was investigated. The coating was produced from colloidal suspension of TiO2 nanoparticles dispersed in 3 wt% solution of Al2(NO3)3, as Al2O3 precursor, in ethanol. TiO2 nanoparticles of two sizes, 15 nm and 32 nm, were used in the experiments. After deposition,...
-
Effects of Micro-Arc Oxidation Process Parameters on Characteristics of Calcium-Phosphate Containing Oxide Layers on the Selective Laser Melted Ti13Zr13Nb Alloy
PublikacjaTitania-based films on selective laser melted Ti13Zr13Nb have been formed by micro-arc oxidation (MAO) at different process parameters (voltage, current, processing time) in order to evaluate the impact of MAO process parameters in calcium and phosphate (Ca + P) containing electrolyte on surface characteristic, early-stage bioactivity, nanomechanical properties, and adhesion between the oxide coatings and substrate. The surface...
-
XPS measurements of the iron elements covered by chromium
Dane BadawczeAnticorrosive coatings are an important issue in modern materials engineering. One of the most commonly used, for that coating materials, is chrome. Three metal elements were measured, named as Turcja, WB Tech and Nomet. Names were given according to producer of elements. XPS measurements of the Cr 2p region give an ansver concering on surface chemical...
-
Quality Improvement of Wear-Resistant Coatings in Plasma Spraying Integrated with High-Energy Heating by High Frequency Currents
Publikacja -
Mechanical and Thermal Properties of W-Ta-B Coatings Deposited by High-Power Impulse Magnetron Sputtering (HiPIMS)
Publikacja -
Characterization and Wear Response of Magnetron Sputtered W–B and W–Ti–B Coatings on WC–Co Tools
Publikacja -
Superconducting properties of an NbN-SiO2 disordered system obtained by ammonolysis of NbN-SiO2 sol-gel derived coatings
PublikacjaW pracy przedstawiono wyniki badań właściwości nadprzewodzących warstw NbN-SiO2. Warstwy uzyskano poprzez azotowanie w temperaturze 1200C otrzymanych metodą zol-żel warstw Nb2O5-SiO2, o różnym stosunku molowym Nb2O5/SiO2. Badania rezystywne przeprowadzono w zakresie temperatur 5-280K. Przeprowadzono również badania absorpcji mikrofal (MMMA). Właściwości nadprzewodzące otrzymanych próbek silnie zależą od grubości warstw jak również...
-
Structure and properties of the Ti+Ti(C,N) coatings obtained in the PVD process on sintered high speed steel
Publikacja -
The influence of plasma-sprayed coatings on surface properties and corrosion resistance of 316L stainless steel for possible implant application
Publikacja -
Recent advances on spinel-based protective coatings for solid oxide cell metallic interconnects produced by electrophoretic deposition
PublikacjaThe application of ceramic protective coatings to the metallic interconnects in solid oxide cells (SOCs) is a viable and effective method to limit interconnect degradation issues. This featured letter provides a critical overview of the main outcomes of current research on the use of the electrophoretic deposition (EPD) technique to produce protective coatings for SOC metallic interconnects, specifically focusing on different approaches...
-
Electrophoretically Deposited Chitosan/Eudragit E 100/AgNPs Composite Coatings on Titanium Substrate as a Silver Release System
PublikacjaDue to the possibility of bacterial infections occurring around peri-implant tissues, it is necessary to provide implant coatings that release antibacterial substances. The scientific goal of this paper was to produce by electrophoretic deposition (EPD) a smart, chitosan/Eudragit E 100/silver nanoparticles (chit/EE100/AgNPs) composite coating on the surface of titanium grade 2 using different deposition parameters, such as the...
-
Influence of Ultrasound on the Characteristics of CaP Coatings Generated Via the Micro-arc Oxidation Process in Relation to Biomedical Engineering
PublikacjaOver the past decade, bone tissue engineering has been at the core of attention because of an increasing number of implant surgeries. The purpose of this study was to obtain coatings on titanium (Ti) implants with improved properties in terms of biomedical applications and to investigate the effect of ultrasound (US) on these properties during the micro-arc oxidation (MAO) process. The influence of various process parameters, such...
-
FLUID BED COATING OF MINITABLETS AND PELLETS WITH OPTIMIZATION OF THE PROCESS BASED ON TAGUCHI METHOD
PublikacjaSmall particles like pellets are coated in fluid bed systems. This method can be also feasible for minitablets but the selection of optimal process parameters is complicated. The aim of the research was to optimize the coating process for minitablets and to compare the conditions required for pellets. Minimum fluidization velocities (umf) for 2.0 and 2.5 mm minitablets and 0.7-0.8 mm or 1.0-1.25 mm pellets were determined experimentally....
-
Interlayer defect evolution in an organic coating system on steel under hydromechanical loading
Publikacja -
Advanced coating of interior of tanks for rising environmental safety - novel applications of polyurethanes
Publikacja -
Mitigating Stripping in Asphalt Mixtures: Pretreatment of Aggregate by Thermoplastic Polyethylene Powder Coating
Publikacja