Filtry
wszystkich: 20677
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: flocculent sludge
-
Investigation of the Effects of Tool Positioning Factors on Peak Temperature in Dissimilar Friction Stir Welding of AA6061-T6 and AA7075-T6 Aluminum Alloys
PublikacjaAmong the emerging new welding techniques, friction stir welding (FSW) is used frequently for welding high-strength aluminum alloys that are difficult to weld by conventional fusion-welding techniques. This paper investigated the effects of tool-positioning factors on the maximum temperature generated in the dissimilar FSW joint of AA6061-T6 and AA7075-T6 aluminum alloys. Three factors of plunge depth, tool offset, and tilt angle...
-
Risks caused by microbiologically influenced corrosion in diesel fuel storage tanks
PublikacjaMicrobiologically influenced corrosion (MIC) poses serious problems for the petrochemical and refinery industries. Particularly favourable conditions for MIC arise in storage tanks and transmission pipelines for mixtures of diesel oil with the addition of a biocomponent (in Poland 7%). The best conditions for the development of MIC occur at the fuel-water interface, where microorganisms are provided with a source of food and water,...
-
INFLUENCE OF SOLID PARTICLE CONTAMINATION ON THE WEAR PROCESS IN WATER LUBRICATED MARINE STRUT BEARINGS WITH NBR AND PTFE BUSHES
PublikacjaThis paper reports on a study of the influence of solid particle contamination on the wear process in water-lubricated slide bearings (steel-acrylonitrile-butadiene rubber (NBR) and steel- polytetrafluoroethylene (PTFE)). To compare the wear of the shaft journal and bushes (NBR and PTFE) when lubricated with fresh water and contaminated water, an experiment was carried out to identify key factors that influence the state of wear...
-
Energy and exergy analysis of negative CO2 emission gas power plant operation using thermodynamic modelling results of the cycle
PublikacjaA developed cycle of negative CO2 emission gas power plant is presented. The cycle is an oxy-combustion gas turbine cycle where the gas fuel is burnt with pure oxygen, and liquid water is injected to the combustor to keep the temperature at an appropriate level for the gas turbine. The negative level of CO2 emission can be obtained by combining CO2 capture method with the usage of a gas fuel based on sewage sludge gasification....
-
Preliminary Results from the Removal of Phosphorus Compounds with Selected Sorption Material
PublikacjaDue to the resources of phosphorous are limited and are exhausted in the next 30 years the management of the resources is become current issue. Most of the phosphorus compounds is lost forever, because it is discharged with sewage into surface waters, causing eutrophication and in this way causing a further problem and challenge. On the other hand, there is a considerable need for phosphorus compounds, primarily in bioavailable...
-
Effect of Tool Positioning Factors on the Strength of Dissimilar Friction Stir Welded Joints of AA7075-T6 and AA6061-T6
PublikacjaFriction Stir Welding (FSW) is a solid-state bonding technique. There are many direct and indirect factors affecting the mechanical and microstructural properties of the FSW joints. Tool offset, tilt angle, and plunge depth are determinative tool positioning in the FSW process. Investigating the effect of these factors simultaneously with other parameters such as process speeds (rotational speed and translational speed) and tool...
-
Characteristics of odors emitted from municipal wastewater treatment plant and methods for their identification and deodorization techniques
PublikacjaOdors emitted from municipal wastewater treatment plants belong to a group of pollutants, which is the main cause of people complaining about atmospheric air quality. The limitation of emissions of unpleasant odors generated by wastewater treatment plants by using appropriate deodorization methods is omitted on numerous occasions. This can have a negative inflence on public trust and the quality of atmospheric air. The article...
-
Modeling the Effects of Slowly Biodegradable Substrate at Large WWTP in Northern Poland
PublikacjaThe essential study was divided into two parts: experimental investigation and mathematical modeling using special platform to computer simulations. In the first part of research an innovative measurement procedure for an indirect determination of the effect of biodegradable particulate and colloidal Xs substrate was developed and implemented. The results of laboratory tests were used futher to verify the mechanism of the hydrolysis...
-
A Model-Based Improved Control of Dissolved Oxygen Concentration in Sequencing Wastewater Batch Reactor
PublikacjaBiochemical processes at wastewater treatment plant are complex, nonlinear, time varying and multivariable. Moreover, relationships between processes are very strong. One of the most important issues is exerting proper control over dissolved oxygen levels during nitrification phase. This parameter has a very large impact on activity of microorganisms in activated sludge and on quality of pollution removal processes. Oxygen is supplied...
-
Natural radioactivity of solid and liquid phases from shale oil and gas prospection in Pomerania
PublikacjaIonizing radiation intensity data and estimation of equivalent absorbed dose from solid and liquid samples from prospection of shale gas and oil at selected sites in Pomerania are presented. Naturally occurring radioactive materials (NORM) are associated with geological formations or fluids and can be enhanced during oil and gas production. They appear in e.g. drilling cuttings, flow back water, produced water, scale and sludge....
-
Influence of alkaline and oxidative pre-treatment of waste corn cobs on biohydrogen generation efficiency via dark fermentation
PublikacjaStages of waste corn cobs processing leading to the production of biohydrogen via dark fermentation are presented and discussed in this paper. Firstly, the effects of pretreatment conditions i.e. alkaline, alkaline-oxidizing and Fenton oxidizing pre-treatment of lignocellulosic biomass on the removal of lignin were examined. The solid residue obtained in the first stage was subjected to saccharification by means of enzymatic hydrolysis....
-
Two-Step Model Based Adaptive Controller for Dissolved Oxygen Control in Sequencing Wastewater Batch Reactor
PublikacjaDissolved Oxygen (DO) concentration is a crucial parameter for efficient operation of biological processes taking place in the activated sludge Wastewater Treatment Plant (WWTP). High-quality DO control is difficult to achieve because of complex nonlinear behavior of the plant and substantial influent disturbances. A method to improve the Direct Model Reference Adaptive Control (DMRAC) technology in application to DO tracking for...
-
Studies on applicability of new solid-phase microextraction fibers for the selective extraction and determination of short - chain monocarboksylic acids
PublikacjaShort-chain monocarobxylic acids, sometimes referred to as volatile fatty acids (VFA), are a group of low molecular weight alkyl monocarboxylic acids that are widely distributed within the environment. These molecules contain any from 2 to 8 carbon atoms and originate from the anaerobic biodegradation of organic matter such as carbohydrates, proteins, and fats. These compounds are commonly found in the effluents from animal farming,...
-
Modelization of Nutrient Removal Processes at a Large WWTP Using a Modified ASM2d Model
PublikacjaThe biodegradation of particulate substrates starts by a hydrolytic stage. Hydrolysis is a slow reaction and usually becomes the rate limiting step of the organic substrates biodegradation. The objective of this work was to evaluate a novel hydrolysis concept based on a modification of the activated sludge model (ASM2d) and to compare it with the original ASM2d model. The hydrolysis concept was developed in order to accurately...
-
Effects of different external carbon sources and electron acceptors on interactions between denitrification and phosphorus removal in BNR processes
PublikacjaThe effects of two different external carbon sources (acetate, ethanol) and electron acceptors (dissolved oxygen, nitrate and nitrite) were investigated under aerobic and anoxic conditions with non-acclimated process biomass from a full-scale biological nutrient removal activated sludge system. When acetate was added as an external carbon source, phosphate release was observed even in the presence of electron acceptors. The release...
-
Activation of peroxymonosulfate using carbon black nano-spheres/calcium alginate hydrogel matrix for degradation of acetaminophen: Fe3O4 co-immobilization and microbial community response
PublikacjaHerein, we focused on the degradation of acetaminophen (ACT) drug in liquid phase by peroxymonosulfate (PMS) activated by carbon black nano-spheres (CBNS). The nanostructured activator was immobilized into calcium alginate hydrogel matrix (CAHM) to avoid the washout of the fine nanostructures. The Langmuir modeling showed an insignificant contribution to the adsorption process in the removal of ACT. The basic pH conditions favored...
-
Model of aeration system at biological wastewater treatment plant for control design purposes
PublikacjaThe wastewater treatment plant (WWTP) is a dynamic, very complex system, in which the most important control parameter is the dissolved oxygen (DO) con-centration. The air is supplied to biological WWTP by the aeration system. Aera-tion is an important and expensive activity in WWTP. The aeration of sewage ful-fils a twofold role. Firstly, oxygen is provided as the main component for biolog-ical processes. Secondly, it supports...
-
Corrosion monitoring as a factor increasing the safety of hydrotechnical infrastructure
PublikacjaWater distribution systems at KGHM S.A. are of great importance for the efficient production of copper and environmental protection. For failures leading to perforation and leakage, the corrosion processes are responsible. This paper aims to assess corrosion on the basis of the analysis of the exposure of the Hydrotechnical Plant pipelines. To this end, the system of transfer and deposition of post-flotation waste as well as the...
-
Fatigue resistance investigation of the IC engine MB11 bearings, working under conditions of dynamic unidirectional loadings
PublikacjaThe slide bearing material MB11 fatigue resistance has been investigated with the application of SMOK - test stand in which dynamic unidirectional loadings to the test bearing is generated. Slide bearing layer consists of the bronze MB11 ( Cu Pb22 Sn 3 ) sintered to the steel shell. Each of the tested bearing has been subject to the standard 20-hour test, under conditions of the full fluid lubrication. Methodology of the experiments,...
-
Handelingen van het Genootschap voor geschiedenis, gesticht onder de benaming 'Société d'Émulation' te Brugge: driemaandelijks tijdschrift voor de studie van geschiedenis en oudheden van Vlaanderen
Czasopisma -
Handelingen van het Genootschap voor geschiedenis, gesticht onder de benaming 'Société d'Émulation' te Brugge: driemaandelijks tijdschrift voor de studie van geschiedenis en oudheden van Vlaanderen
Czasopisma -
Termowizja jako narzędzie weryfikacji stanu elementów ochronnych SMD podczas badań udarowych
PublikacjaPrzedstawiono wyniki badań przyrostów temperatury rejestrowanych za pomocą kamery termowizyjnej ochronnych elementów SMD podczas wykonywania badań odporności na udary napięciowe wykonywane wg normy EN61000-4-5 dla różnych poziomów sprzężeń impedancyjnych
-
Nonlinear Fuzzy Control System for Dissolved Oxygen with Aeration System in Sequencing Batch Reactor
PublikacjaBiological processes at a wastewater treatment plant are complex, multivariable, time varying and nonlinear. Moreover, interactions between the components are very strong. Control of dissolved oxygen is one of most important task at the plant. The level of dissolved oxygen in aerobic tanks has significant influence on behaviour and activity of microorganisms at the plant. Air for aerated tanks is supplied by the aeration system...
-
Mesophilic and thermophilic dark fermentation course analysis using sensor matrices and chromatographic techniques
PublikacjaProduction of biofuels from biomass is expected to benefit the society and the environment. At present, bio waste residues processing includes hydrolysis, dark fermentation, photofermentation, pyrolysis, gasification, and chemical synthesis. As the composition and the chemical structure of organic substances affect the efficiency of mentioned processes, it is believed that the glucose concentration is a crucial parameter for the...
-
Stochastic optimisation algorithm for optimisation of controller parameters for control of dissolved oxygen in wastewater treatment plant
PublikacjaWastewater treatment plants (WWTPs) are very important facilities for mankind. They enable the removal and neutralisation of man-made pollutants. Therefore, it is important for wastewater treatment plants to operate as efficiently as possible so that the level of pollutants in the treated wastewater meets specific requirements. This paper concerns the design of a hierarchical nonlinear adaptive control system for dissolved oxygen...
-
EMISJA AKUSTYCZNA JAKO SYGNAŁ DIAGNOSTYCZNY ODWZOROWUJĄCY ZMĘCZENIOWE ZUŻYCIE WARSTW ŚLIZGOWYCH PANWI ŁOŻYSK GŁÓWNYCH I KORBOWYCH SILNIKÓW O ZAPŁONIE SAMOCZYNNYM
PublikacjaW artykule przedstawiono wyniki badań laboratoryjnych, z których wynika, że emisja akustyczna (EA) może być uznana za sygnał diagnostyczny, przydatny do identyfikacji stanu technicznego łożysk głównych i korbowych okrętowych silników o zapłonie samoczynnym. Wykazano w nim bowiem, że parametry emisji akustycznej takie jak: czas rejestracji, energia sygnału, amplituda sygnału, ilość przekroczeń poziomu dyskryminacji, czas narastania,...
-
Rafał Janowicz dr hab. inż. arch.
OsobyRafał Janowicz jest adiunktem na wydziale Architektury Politechniki Gdańskiej w Katedrze Technicznych Podstaw Projektowania Architektonicznego od 2011 roku. Ukończył studia na kierunku Architektura i Urbanistyka na Wydziale Architektury Politechniki Gdańskiej w 2001 roku, a dwa lata później na kierunku Zarządzanie i Marketing na Wydziale Zarządzania i Ekonomii PG. W 2011 r. obronił pracę doktorską na Wydziale Architektury Politechniki...
-
Assessment of Corrosive Behaviour and Microstructure Characterization of Hybrid Friction Stir Welded Martensitic Stainless Steel
PublikacjaThis study examined the effect of induction heating on the microstructure and corrosion characteristics of hybrid friction stir welded AISI 410 stainless steel. Five joints have been produced with different friction stir welding parameters like welding speed, spindle speed, plunge depth, and induction power. Their microstructures were evaluated using a scanning electron microscope, and chemical composition was examined using...
-
The influence of image masks definition onsegmentation results of histopathological imagesusing convolutional neural network
PublikacjaAbstract—In the era of collecting large amounts of tissue materials, assisting the work of histopathologists with various electronic and information IT tools is an undeniable fact. The traditional interaction between a human pathologist and the glass slide is changing to interaction between an AI pathologist with a whole slide images. One of the important tasks is the segmentation of objects (e.g. cells) in such images. In this...
-
Nitrogen mass balance and mathematical model of a Structured- Bed Reactor (SBRRIA)
PublikacjaAn up-flow structured-bed reactor subjected to recirculation and intermittent aeration (SBRRIA) was operated under varying influent conditions. The influent COD/N ratio was adjusted by maintaining a stable organic loading rate (average of 1.07 kgCOD m-3 d-1) and changing the nitrogen loading rate from 0.1 to 0.4 kg N m-3. Therefore, three different COD/N ratios were tested: 9.7±1 (Scenario 1); 7.6±1 (Scenario 2) and 2.9±1 (Scenario...
-
Landfill leachates and wastewater of maritime origin as possible sources of endocrine disruptors in municipal wastewater
PublikacjaIn this study, wastewater from municipal services, such as a port wastewater reception facility (PRF-WW) and a municipal solid waste plant (MSWP), was tested for the presence of the suspected endocrine-disrupting compounds phthalates (PAEs) and bisphenol A (BPA). PAEs and BPA were found in this study in high concentrations in raw wastewater obtained from passenger ships (RMT-WWs) (up to 738 μg/L and 957 μg/L, respectively) collected...
-
The application of moving bed biofilm reactor to denitrification process after trickling filters
PublikacjaThe paper presents research of a prototype moving bed biofilm reactor (MBBR). The device was used for the post-denitrification process and was installed at the end of a technological system consisting of a septic tank and two trickling filters. The concentrations of suspended biomass and biomass attached on the EvU Perl moving bed surface were determined. The impact of the external organic carbon concentration on the denitrification...
-
Treatment innovation using solar/UV In book: The Treatment of Pharmaceutical Wastewater: Innovative Technologies and the Adaptation of Treatment Systems
PublikacjaSince ancient times, sunlight irradiation has been widely used for water purification. Apart from solar water disinfection techniques, UV irradiation is of particular interest when considering the photodegradation of various classes of emerging pollutants. Pharmaceutically active compounds are one of the largest classes of micropollutants. The main sources of these contaminants in wastewater and aqueous environments are households,...
-
Thermal utilization of meat-and-bone meal using the rotary kiln pyrolyzer and the fluidized bed boiler – The performance of pilot-scale installation
PublikacjaThermal utilization of meat-and-bone meal (MBM) is subject to stringent regulations that are meant to provide elimination of any potential pathogens. Incineration as well as other possible routes for thermal conversion of MBM are still at the research state. The universal technology was developed that allows to combust various types of waste organic materials, including animal waste, municipal solid waste and sludge, mixed at any...
-
Production of Biogas from Distillation Residue as a Waste Material from the Distillery Industry in Poland
PublikacjaIn this paper, the possibility to obtain an alternative source of energy from methane fermentation, catalysed by biomass, has been discussed in detail. As a main substrate, the distillation residue from the distillery industry was taken in the case of mono-fermentation and its co-fermentation with sewage sludge. The results showed that higher biogas and methane production can be obtained in a mono-fermentation process. Fermentation...
-
A distillery by-product as an external carbon source for enhancing denitrification in mainstream and sidestream treatment processes
PublikacjaThe use of fusel oil as an 'alternative' carbon source for denitrification in the mainstream and sidestream treatment processes was studied. Research comprised two kinds of batch experiments as well as acclimation of process biomass to external carbon sources. In the conventional nitrate utilization rate (NUR) measurements (one-phase experiments with non-acclimated biomass), the NUR with fusel oil was 1.4-1.7 g N/(kg VSS•h which...
-
Modelling of sequencing batch reactor operating at various aeration modes
PublikacjaThe presented study involved designing a computer model of a sequencing batch reactor (SBR) at laboratory scale. The data pertaining to the technical aspects of the bioreactor and quality indicators of wastewater constituted the input for the employed simulation tool, i.e. GPS-X software package. The results of a simulation involving a 12-hour operation cycle are presented in this work; each cycle included 6 phases: filling, mixing,...
-
A fast start-up of the organotrophic anammox process inoculated with constructed wetland sediment
PublikacjaOrganotrophic anaerobic ammonium oxidation (anammox) bacteria can utilize small volatile fatty acids with nitrate as electron acceptors with less energy consumption and no biomass production. To achieve a faster and stable start-up of organotrophic anammox process, in this study, the growth of organotrophic anammox bacteria seeded from hybrid constructed wetland (CW) sediment under different TOC/TN ratios and different chloramphenicol...
-
Combination of air-dispersion cathode with sacrificial iron anode generating Fe2+Fe3+2O4 nanostructures to degrade paracetamol under ultrasonic irradiation
PublikacjaIn the present study, ultrasound (US) was coupled with an electrochemical process (ECP) consisting of a novel cathode of carbon cloth (CC)-carbon black (CB) as the nano-composite air-dispersion cathode (NADC) for the degradation of paracetamol (APAP) in an aquatic medium. The NADC favored in situ production of H2O2 by the cathodic reduction. The implementation of iron sacrificial anode instead of dimensionally stable anodes resulted...
-
Sonocatalytic degradation of tetracycline antibiotic using zinc oxide nanostructures loaded on nano-cellulose from waste straw as nanosonocatalyst
PublikacjaThe aim of the present investigation was the combination of ZnO nanostructures with nano-cellulose (NC) for the efficient degradation of tetracycline (TC) antibiotic under ultrasonic irradiation. The removal efficiency of 12.8% was obtained by the sole use of ultrasound (US), while the removal efficiency increased up to 70% by the US/ZnO treatment process. Due to the integration of ZnO nanostructures with NC, the removal efficiency...
-
Key issues in modeling and optimization of lignocellulosic biomass fermentative conversion to gaseous biofuels
PublikacjaThe industrial-scale production of lignocellulosic-based biofuels from biomass is expected to benefit society and the environment. The main pathways of residues processing include advanced hydrolysis and fermentation, pyrolysis, gasification, chemical synthesis and biological processes. The products of such treatment are second generation biofuels. The degree of fermentation of organic substances depends primarily on their composition...
-
Development of a simple biogas analyzer module (BAM) for real-time biogas production monitoring
PublikacjaAnaerobic digestion (AD) relies on the cooperation of specific microbial communities, making it susceptible to process disruptions that could impact biogas production. In this regard, this study presents a technological solution based on the Arduino platform, in the form of a simple online monitoring system that can track the produced biogas profile, named as biogas analyzer module (BAM). The applicability of the BAM focused on...
-
A stochastic approach for the solution of single and multi – objective optimisation problems of biological processes in sequencing batch reactor
PublikacjaThis paper investigates the impact of implementing single and multi-optimisation solutions on the biological treatment process in a sequencing batch reactor (SBR). The research is based on a case study of the water resource recovery facility (WRRF) in Swarzewo, Northern Poland. The paper introduces the adaptive extremum seeking control (ESC) method for dissolved oxygen (DO) concentration control and places it in a layered control structure....
-
New Procedures for Control of Industrial Effluents Treatment Processes
PublikacjaThis work presents the procedures for monitoring volatile organic compounds during treatment of industrial effluents. The investigation was carried out for a specific effluent—caustic effluent from bitumen production. The developed procedures enable more detailed control of the effectiveness of wastewater treatment than standard procedures. Caustic effluents from bitumen production have a complex physicochemical form and consist...
-
Resistance of Escherichia coli and Enterococcus spp. to selected antimicrobial agents present in municipal
PublikacjaIn this study, the susceptibility to erythromycin (E) and to trimethoprim/sulfamethoxazole (SXT) among isolates of Enterococcus spp. and Escherichia coli was tested, respectively. Both fecal indicators were detected and isolated from raw(RW) and treated wastewater (TW) as well as from samples of activated sludge (AS) collected in a local wastewater treatment plant (WWTP). Biodiversity of bacterial community in AS was also monitored...
-
Application of persulfate-based oxidation processes to address diverse sustainability challenges: A critical review
PublikacjaOver the past years, persulfate (PS) is widely applied due to their high versatility and efficacy in decontamination and sterilization. While treatment of organic chemicals, remediation of soil and groundwater, sludge treatment, disinfection on pathogen microorganisms have been covered by most published reviews, there are no comprehensive and specific reviews on its application to address diverse sustainability challenges, including...
-
Recent Advancements in Cyclodextrin-Based Adsorbents for the Removal of Hazardous Pollutants from Waters
PublikacjaWater is an essential substance for the survival on Earth of all living organisms. However, population growth has disturbed the natural phenomenon of living, due to industrial growth to meet ever expanding demands, and, hence, an exponential increase in environmental pollution has been reported in the last few decades. Moreover, water pollution has drawn major attention for its adverse effects on human health and the ecosystem....
-
Pilot installation for thermal utilization of meat-and-bone meal using the rotary kiln pyrolyzer and the fluidised bed boiler
PublikacjaThe technology of thermal utilization of meat-and-bone meal (MBM) is still at the research state. However, there are already a number of existing pilot-scale installations that provide the complete, effective and environmentally safe process conducting. The universal technology was developed that allows to combust various types of waste, including animal waste, municipal waste and sludge, mixed at any ratio with different types...
-
Adam Inglot dr inż.
OsobyAdam Inglot (urodzony 3 października 1984 w Rzeszowie) studiował Inżynierię Środowiska oraz Geodezję i Kartografię na Wydziale Geodezji Górniczej i Inżynierii Środowiska Akademii Górniczo-Hutniczej w Krakowie. Inżynierię Środowiska ukończył w 2011 w stopniu mgr inż. broniąc pracę „Weryfikacja przydatności modelu GeoMod do prognozowania procesu urbanizacji w aglomeracji krakowskiej” u dra inż. Wojciecha Drzewieckiego. Natomiast...
-
Selected Problems of Experimental Testing Marine Stern Tube Bearings
PublikacjaThis paper presents typical methods for conducting experimental tests on main shaft slide bearings. There are described their possible testing capabilities, advantages, drawbacks and limitations. Various testing methods were analyzed to find a solution able of providing a wide range of possible investigations at possibly acceptable limitations.