Wyszukiwarka
Katedra Energetyki i Aparatury Przemysłowej
Publikacje
Filtry
wszystkich: 805
Katalog Publikacji
Rok 2018
-
Numerical Study of Turbulent Flow and Heat Transfer of Nanofluids in Pipes
PublikacjaIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (Reynolds number between 6000 and 12000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Ocena sprawności cyklu roboczego Pojazdu do Usuwania Odpadów z Pojemników na podstawie danych eksploatacyjnych
PublikacjaW artykule przedstawiona została metoda oceny sprawności cyklu roboczego śmieciarki. Wykorzystując dane eksploatacyjne wyznaczono dwa reprezentatywne cykle i na ich podstawie obliczono zarówno sprawność całego cyklu, jak i jego poszczególnych faz. Porównano wartości energii potrzebnej do opróżniania pojemników, energii do zagęszczania odpadów oraz energii z paliwa. Przedstawiono przebiegi mierzonych i obliczonych wartości w czasie...
-
Optymalizacja parametrów pracy siłowni osiągającej zaawansowane super ultrandkrytyczne parametry pary świeżej oraz modyfikacje obiegu parowego pozwalające zwiększyć jego sprawność
PublikacjaW niniejszym artykule przedstawiono metody optymalizacji parametrów siłowni osiągającej zaawansowane super ultranadkrytyczne parametry pary. Stworzono modele obliczeniowe trzech nadkrytycznych obiegów parowych: z pojedynczym przegrzewam międzystopniowym, z podwójnym przegrzewem międzystopniowym oraz „Master Cycle". Zaprezentowano wpływ dodatkowego przegrzewu międzystopniowego i konfiguracji Master Cyde na sprawność obiegu parowego....
-
Particulate Matter Production of Small Heat Source Depending on the Bark Content in Wood Pellets
PublikacjaWood pellets as biofuel are more and more used in small heat sources in Europe. Standard wood pellets are produced from wood sawdust without bark. The paper deals about the impact of bark in wood pellets on their properties and combustion process. Special attention in this work is paid to production of particulate matter during combustion of wood pellets depending on bark content. There were experimentally produced spruce wood...
-
Performance of the domestic micro ORC equipped with the shell-and-tube condenser with minichannels
PublikacjaIn this paper, the original compact shell-and-tube heat exchanger with circular minichannels of in-house design and manufacturing is presented as the condenser for the domestic micro heat and power plant investigations as well as other future technical applications. The heat exchanger is equipped with turbulizing baffles inside the shell. The shell itself is made of a tubular sleeve having an inner diameter of 0.067 m and the length...
-
Possibilities of Increasing the Overall Efficiency of Gas-steam CHP Microplant
PublikacjaThe paper presents ways to increase the efficiency of a gas-steam micro power plant by modifying the cycle combination. The modification consists in partial release of the fluid downstream of the gas turbine and using it for ORC fluid overheating and evaporation. Advantages of this solution over the simplest gas and steam cycles’ combination are demonstrated.
-
Pressure drop related to flow maldistribution in a model minichannel plate heat exchanger
PublikacjaThe paper describes the issues related to the pressure drop that accompanies the phenomenon of maldistribution of working fluid between the channels of a model minichannel plate heat exchanger. The research concerns a single exchanger's plate containing 51 (in every geometry) parallel rectangular minichannels of hydraulic diameters 461 µm, 571 µm, 750 µm and 823 µm. In addition, the more complex geometry has been investigated,...
-
Pre-swirl energy saving device in marine application
PublikacjaThis paper covers topics of energy saving device (ESD) with application to marine propulsors. The form of ESD, considered in this paper, consists of fixed lifting foils mounted in front of the screw propeller (the pre-swirl stator/guide vanes). An algorithm for designing propulsion systems, consisting of guide vanes and screw propeller, is presented. The proposed method relies on hybrid lifting line (guide vanes)-lifting surface...
-
Research on the phenomena of warming up and free cooling down the car engine
PublikacjaThe average cold start temperature in Europe is 9 degrees C. However, not the average is the most important for the composition of exhaust gases and associated air pollution. The most onerous for the environment are the winter starts when automotive emissions of harmful gases add up in cities with those of home heating systems. The paper presents preliminary studies of warming up and cooling down processes in various environmental conditions....
-
Response to the queries raised by Dr M.M. Awad in a letter to editor comments on “Pressure drop of HFE7000 and HFE7100 during flow condensation in minichannels”
Publikacja.
-
Simple Computational Methods in Predicting Limit Load of High-Strength Cold-Formed Sections due to Local Buckling: A Case Study
PublikacjaCold-formed thin-walled sections are prone to local buckling caused by residual stresses, geometrical imperfections and inconsistency of material properties. We present a real case of buckling failure and conduct a numerical and experimental study aimed to identify methods capable of predicting such failures. It is important because designers of structures are getting more FEA-oriented and tend to avoid lengthy procedures of cold-formed...
-
Smart heating system for home extending utilization of renewable energy sources
PublikacjaIn the paper a modern approach to smart home heating is presented. Proposed solution utilizes at least two low-polluting energy source technologies. The main idea is to connect well known ecological energy sources in a way that they can support each other and minimize risks of failure when using single system or even both of them but managed in separate way. Considered energy technologies, used separatelly, have disadvan-tages,...
-
Stan prawny w zakresie utylizacji odpadów medycznych w Polsce i Unii Europejskiej
PublikacjaWzrost liczby osób korzystających z leczenia domowego, a także rosnąca ilość gabinetów zajmujących się medycyną estetyczną i tatuażem prowadzi do tego, że problem odpadów potencjalnie niebezpiecznych zaczyna dotykać coraz większe grupy społeczeństwa, a nie tylko wykwalifikowanego personelu szpitalnego. W związku z tym istotna jest zarówno edukacja w zakresie gospodarki odpadami medycznymi, jak i wypracowanie możliwości ich bezpiecznej...
-
Termiczne metody utylizacji odpadów medycznych
PublikacjaW artykule przedstawiono dopuszczone przez polskie prawo metody unieszkodliwiania odpadów medycznych, ze szczególnym wyróżnieniem najczęściej stosowanych metod termicznych. Omówiono wytyczne dla prowadzenia procesu utylizacji odpadów w instalacji termicznej przeróbki odpadów. W końcowej części publikacji opisane zostały dwie jednostki przeznaczone do utylizowania odpadów medycznych, tj. instalacja w Zakładzie Utylizacji Odpadów...
-
The Effect of Full-Cell Impregnation of Pine Wood (Pinus sylvestris L.) on Changes in Electrical Resistance and on the Accuracy of Moisture Content Measurement Using Resistance Meters
PublikacjaThe impact of the full-cell impregnation of pine wood was investigated with respect to changes in electrical resistance and the accuracy of moisture content measurement. This study compared the resistance of impregnated and untreated pine timber harvested from the northern part of Poland (Pomeranian region). The wood was impregnated by the vacuum-pressure method. The preservative (TANALITH E 3475) and coloring (TANATONE 3950) agents...
-
The effect of reduced pressure on carbon dioxide flow boiling heat transfer in minichannels
Publikacja. In the paper presented are the results of the study on the effect of reduced pressure on flow boiling heat transfer data in minichannels as well as conventional ones. That effect renders that most of heat transfer correlations fail to return appropriate results of predictions. Mostly they have been developed for the reduced pressures from the range 0.1-0.3. The special correction has been postulated to the in-house model of flow...
-
The influence of microjet array area ratio on heat transfer in the compact heat exchanger
PublikacjaThe paper describes the comprehensive study on the effect of microjet array geometrical parameters on the heat transfer enhancement in the modular heat exchanger. The conducted experimental study provides an experimental database on single phase submerged microjet heat transfer. The Wilson plot method was applied to determine the heat transfer coefficients in the laminar and transition flow regimes of a liquid-to-liquid heat exchanger....
-
The use of liquid crystal thermography TLC and particle image velocimetry PIV in selected technical applications
PublikacjaNowadays, the energy cost is very high and this problem is carried out to seek techniques for improvement of the aerothermal and thermal (heat flow) systems performances in different technical applications. The transient and steady-state techniques with liquid crystals for the surface temperature and heat transfer coefficient or Nusselt number distribution measurements have been developed. The flow pattern produced by transverse...
-
Thermal and hydraulic phenomena in boundary layer of minijets impingement on curved surfaces
PublikacjaPresented work considers flow and thermal phenomena occurring during the single minijet impingement on curved surfaces, heated with a constant heat flux, as well as the array of minijets. Numerical analyses, based on the mass, momentum and energy conservation laws, were conducted, regarding single phase and two-phase simulations. Focus was placed on the proper model construction, in which turbulence and boundary layer modeling...
-
Thermal energy storage using stearic acid as PCM material
PublikacjaThis work presents an experimental study of thermal energy storage by use of PCM. The aim of the study was to establish the influence of different inlet temperature of heat transfer fluid (HTF) and different Reynolds number of HTF on intensity of charging process. The PCM used in this study was stearic acid and water was used as HTF. A copper helical coil mounted in cylindrical container served as a heat transfer surface.
-
Turbulence models impact on the flow and thermal analyses of jet impingement
PublikacjaAccurate numerical reconstruction of heat and mass transfer processes in particular applications, such a jet impingement, is difficult to obtain even with the use of modern computational methods. In the proposed paper, the flow and thermal phenomena occurring during single minijet impingement on the flat, concave and convex, heated surfaces were considered. Problem of impingement on non-flat surface, still not common and purely...
-
Wykorzystanie magazynu chłodu w kompaktowej komorze przechowalniczej
PublikacjaNiniejszy artykuł został poświęcony możliwości wykorzystania pasywnych systemów chłodzenia w mobilnych komorach przechowalniczych. Dokonano przeglądu rozwiązań dostępnych na rynku komór termicznych wraz z wykorzystywanymi w nich technologiami chłodzenia. Przeprowadzono analizę możliwych do zastosowania nośników chłodu w systemach pasywnego chłodzenia. Wykazano, iż oprócz popularnych na rynku materiałów zmiennofazowych (PCM – ang....
-
Zintegrowany Program Rozwoju Politechniki Gdańskiej
PublikacjaPolitechnika Gdańska realizuje projekt Zintegrowany Program Rozwoju Politechniki Gdańskiej (POWER 3.5) dofinansowywany z Europejskiego Funduszu Społecznego. Celem projektu jest podniesienie jakości kształcenia na studiach II i III stopnia, zwiększenie efektywności zarządzania Politechniką Gdańską oraz podniesienie kompetencji kadr. Projekt jest realizowany od 1 kwietnia 2018 roku do 31 marca 2022 roku. Instytucją pośredniczącą...
Rok 2017
-
A SHORT REVIEW OF BLOOD FLOW MODELLING METHODS: FROM MACRO- TO MICROSCALES
PublikacjaThe aim of this paper it to review various scale approaches to the blood flow modelling. Blood motion may be described by three types of mathematical models according to the observed scales or resolutions, namely microscopic, mesoscopic and macroscopic descriptions. The above approaches are discussed together with their advantages and disadvantages. Several results of mesoscopic simulations are presented with particular attention...
-
A simplified energy dissipation based model of heat transfer for subcooled flow boiling
PublikacjaIn the paper a model is presented based on energetic considerations for subcooled flow boiling heat transfer. The model is the extension of authors own model developed earlier for saturated flow boiling and condensation. In the former version of the model we used the heat transfer coefficient for the liquid single-phase as a reference level, due to the lack of the appropriate model for heat transfer coefficient for the subcooled...
-
An application for a new type of pneumatic engine concept
PublikacjaHeavy trucks are often equipped with loading and unloading systems like dock levellers with swing lip or telescopic lip. Most of these devices require hydro-electrical energy supply systems (eg. the pump that presses the working substance to the actuators must be propelled by electric engine.) The space taken by pump with electric engine can be reduced on condition that a new type of pneumatic drive will be considered. It is possible...
-
Analysis of the possibilities of using of DME fuel in motor boat drive systems
PublikacjaThe characteristics of alternative fuel for diesel: dimethyl ether (DME) and an analysis of the potential to reduce emissions of toxic compounds by the engines when running on this fuel have been presented in this work. Basic types of design solutions of gas supply and control systems, possible for use in internal combustion engines with DME supply have been also presented. The paper presents a study of the legislation and an analysis...
-
Analysis of the possibility of determining the general characteristics using the operational data of a vehicle engine
PublikacjaThe paper presents an analysis of the possibility of determining the general characteristics using the operational data of an engine of refuse collection vehicle. Data acquisition was done by reading information from the CAN network using FMS standard (Fleet Management System), which is widely used in heavy duty vehicles since year 2002. The paper presents the analysis of the expected measurement uncertainties resulting from the...
-
Application in circular sawing machines of the experimental results of investigations of the chip removing system operation
PublikacjaThe experimental results of the chip removing system operation are presented. The main aim of them was to optimize suction system of the panel saw Fx3 and its follower Fx550. The attention was focused on the upper casing, which was the part of removing system. Within the framework of the work a systematic experimental study of pressure distribution in the casing during operation of the selected rotational speed of saw blade with...
-
Application of road map of operating condition for estimation of fuel and electric energy consumption from city transport
PublikacjaThe paper presents procedure of data collecting and generation of road map of operating condition in the selected urban area. This map allows forecasting the selected vehicle operating parameters for the assumed road. The main parameters calculated using the road maps of operating conditions are: total energy spent to drive the selected vehicle, consumed fuel, travel time, average speed of travel, CO2 emissions. Presented example...
-
ARRAY OF MINIJETS – THERMAL AND HYDRAULIC PHENOMENA IN BOUNDARY LAYER
PublikacjaPresented work considers flow and thermal phenomena occurring in the system consisting of minijets array and heated with constant heat flux surface. Numerical analyses, based on the mass, momentum and energy conservation laws, were conducted. Focus was placed on the proper model construction, in which turbulence and boundary layer modelling was crucial. Calculations were done for various mass flow rates. The main calculations were...
-
Badania eksperymentalne intensyfikacji wymiany ciepła wymiennika U-rurowego z wykorzystaniem turbulizatora helikoidalnego
PublikacjaW niniejszej pracy zostały zaprezentowane możliwości intensyfikacji wymiany ciepła po stronie płaszcza wymiennika U-rurowego. Badania eksperymentalne zostały przeprowadzone zarówno dla wymienników referencyjnych tj. prosty – rura w rurze, U-rurowy bez turbulizacji jak i wymiennika z turbulizatorem helikoidalnym. Dla konstrukcji rura w rurze w celu uzyskania wartości referencyjnych przeprowadzono pomiary w układzie woda-woda oraz...
-
Badania eksperymentalne U-rurowego wymiennika ciepła z turbulizacją pasywną
PublikacjaArtykuł dotyczy badań eksperymentalnych wymiennika U-rurowego. W wymienniku została zastosowana turbulizacja pasywna w postaci spiralnej wkładki. Artykuł zawiera opis stanowiska oraz wstępne wyniki badań.
-
Calculation method for flow boiling and flow condensation of R134a and R1234yf in conventional and small diameter channels
PublikacjaThe paper presents the results of calculations performed using the authors’ model to predict the heat transfer coefficient during flow boiling for two refrigerants R134a and R1234yf. The experimental data from various past studies have been collected and the calculations have been conducted for the full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house...
-
Capillary pumped loop as a tool for collecting large heat fluxes from electronic devices on warships
PublikacjaThe combat potential of future warships will be directly related to the use of modern electronic devices being parts of advanced systems, such as, for instance, radar systems, fire aiming systems, fire detection systems, electric drive systems, and even electronic and radio-electronic weaponry, railguns and lasers, installed on these warships. The capacity and functionality of these devices is continually increasing, at decreasing...
-
CAUSALITY IN MODELS OF THERMAL PROCESSES IN SHIP ENGINE ROOMS WITH THE USE OF BOND GRAPH (BG) METHOD
PublikacjaWith a single approach to modeling elements of different physical nature, the method of Bond Graph (BG) is particularly well suited for modeling energy systems consisting of mechanical, thermal, electrical and hydraulic elements that operate in the power system engine room. The paper refers to the earlier presented new concept of thermal process modeling using the BG method. The authors own suggestions for determining causality...
-
CHARAKTERYSTYKA WYMIANY CIEPŁA I OPORÓW PRZEPŁYWU OMYWANIA MIKROSTRUGAMI ROZWINIĘTEJ POWIERZCHNI
PublikacjaW artykule przedstawiono eksperymentalne badania kompaktowego wymiennika ciepła z intensyfikacją przejmowania ciepła przy użyciu mikrostrug. Niniejszy artykuł przedstawia projekt i testy prototypu, wymiennika ciepła typu mikrostrugowego. Modułowa konstrukcja wymiennika umożliwia zmianę wymiarów geometrycznych, a także zmianę materiału przegrody wymiennika ciepła. Metoda graficzna Wilsona została z zastosowana w celu określenia...
-
Co zrobić z nieużywaną wieżą ciśnień? Studium historyczno-koncepcyjne (część I)
PublikacjaArtykuł przedstawia historię i (dawną) funkcję wieży ciśnień (obecnie nieużytkowanej, stanowiącej konstrukcyjną część budynku Laboratorium Maszynowego Politechniki Gdańskiej. Jest to wstęp do przedstawienia koncepcji adaptacji tego obiektu na modelową mikro-elektrownię szczytowo-pompową, mogącą posłużyć badaniom i dydaktyce.
-
Co zrobić z nieużywaną wieżą ciśnień? Studium historyczno-koncepcyjne (część II)
PublikacjaDruga część artykułu przedstawia obliczenia parametrów pracy, jakich można się spodziewać, realizując koncepcję mikro-elektrowni szczytowo-pompowej w oparciu o adaptację nieczynnej wieży ciśnień stanowiącej część budynku Laboratorium Maszynowego. Przedstawiona została także analiza możliwości współpracy z istniejącą instalacją fotowoltaiczną w kierunku uzyskania kompletnego mikro-systemu energetycznego.
-
Comparative study of operation of condensing and traditional boilers equipped with ORC module for electricity generation
PublikacjaThe study analyzed the operation of the "traditional" boiler equipped with the ORC module as the similar arrangement but with the condensing boiler. In the case of a conventional boiler there is noted a greater fuel consumption and the greater power generated than in the case of the unit with the condensing boiler. Postulated is the indicator in the form of a ratio of turbine power to the mass flow rate of fuel, which in turn gives...
-
Comparative study of operation of condensing and traditional boilers equipped with the ORC module for electricity generation
PublikacjaCondensing technology applied to boilers is to make full use of thermal energy contained in the fuel. That means that additionaly the heat from condensation of exhaust gases can be used for the purposes of heating the domestic hot water and to cover the demand for central heating. The study analyzed the operation of the "traditional" boiler equipped with the ORC module as the similar arrangement but with the condensing boiler....
-
Cooperation of ORC installation with a gas boiler as a perspective co-generation system for households
PublikacjaThis paper reports tests of an innovative micro-CHP unit prototype, consisting of a traditional gas boiler and organic Rankine cycle (ORC), which incorporates original system components such as an axial vapour microturbine, evaporator and condenser. The system co-generates heat and electricity for a single household or a group of households. Electricity is only a by-product during production of heat. While testing the prototype,...
-
Cutting power estimation of the bandsawing process of beech wood (Fagus sylvatica L.) dried in three operating modes
PublikacjaIn this paper the predicted values of cutting power for bandsawing machine (ST100R, f. Stenner), which is located at the sawmill company Complex in Dziemiany, were presented. The values of cutting power were forecasted for beech wood (Fagus sylvatica L.), from the northern part of Pomerania region in Poland, which was dried in three operating modes: BKP - air drying at 25oC, BKS - air-steam mixture drying at 80oC, BKW - steam drying...
-
Design and experimental investigations of a cylindrical microjet heat exchanger for waste heat recovery systems
PublikacjaCompact heat exchangers have more and more applications in many areas, including the HVAC, food and petrochemical industry. This paper describes the development of heat exchanger technology for waste heat recovery (WHR) from a range of processes. Case-study testing shows that the proposed heat exchanger can successfully enhance heat transfer and recover waste heat in a range of applications making them economically, environmentally and...
-
Design of a test bench for determining the general characteristics of an internal combustion engine using a hydraulic power take-off system
PublikacjaThe paper presents a design of an engine test bench, which is used to determine the general characteristics of a truck engine using a power take-off (PTO). PTO drives a hydraulic system that generates a load on the engine at various points in its operation in the power range specified by the hydraulic system. The design allows for stationary and mobile tests with the test bench mounted on the truck, without any modification of...
-
Detailed experimental investigations on frictional pressure drop of R134a during flow boiling in 5 mm diameter channel: The influence of acceleration pressure drop component =Études expérimentales détaillées sur la chute de pression frictionnelle du R134a lors de l'ébullition en écoulement dans un canal de 5 mm de diamètre : influence de la composante d'accélération de la chute de pression
PublikacjaThis article presents detailed two-phase diabatic pressure drop data for refrigerant R134a at a saturation pressure of 5.5 bar corresponding to the saturation temperature of 19.4 °C. Study cases have been set for a mass flux varying from 100 to 500 kg m−2 s−1. The obtained data are used as a validation of the void fraction literature models, a set of graphs shows comparisons, for a representative set of experimental conditions,...
-
Determination of dryout localization using a five-equation model of annular flow for boiling in minichannels
PublikacjaDetailed studies have suggested that the critical heat flux in the form of dryout in minichannels occurs when the combined effects of entrainment, deposition, and evaporation of the film make the film flow rate go gradually and smoothly to zero. Most approaches so far used the mass balance equation for the liquid film with appropriate formulations for the rate of deposition and entrainment respectively. It must be acknowledged...
-
Experimental investigations on adiabatic frictional pressure drops of R134a during flow in 5mm diameter channel
PublikacjaThe article presents detailed two-phase adiabatic pressure drops data for refrigerant R134a at a saturation pressure of 5.5 bar corresponding to the saturation temperature of 19.4 °C. Study cases have been set for a mass flux varying from 100 to 500 kg/m2 s. The frictional pressure drop was characterized for the refrigerant R134a, for vapor qualities ranging from 0 to 1. Long-time thermal stability of test facility allowed to gather...
-
Experimental study of pressure rise at the evaporator of capillary pumped loop with acetone and water as working fluids
PublikacjaIn this work studied is the possibility of fluid pumping using capillary forces in the capillary pumped loop. Experimental and theoretical studies have been performed to understand the phenomena associated with heat transfer in porous structure of the evaporator. The capillary effect was studied during operation of two different capillary porous structures with two different working fluids, namely water and acetone. The results...
-
EXPERIMENTAL VERIFICATION OF THE METHOD OF FLOW BOILING AND FLOW CONDENSATION HEAT TRANSFER PREDICTION FOR SELECTED FLUIDS
PublikacjaIn the paper presented are the results of calculations using authors own model to predict heat transfer coefficient during flow boiling of different refrigerants. The experimental data from various research studies from literature were collected. Calculations were conducted for a full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in- house developed model....