Filters
total: 843
filtered: 688
Search results for: flow control
-
Modelling of flow boiling process in small diameter tubes.
PublicationW pracy zastosowano standardową korelację wrzenia w przepływie (wyprowadzoną dla rur o konwencjonalnych wymiarach) do przypadków wrzenia w rurach o małych średnicach. Porównanie wyników obliczeń z danymi literaturowymi wykazało nieużyteczność tej korelacji. Wykazano zatem potrzebę prowadzenia badań podstawowych celem uzyskania korelacji pozwalającej umiejętnie przewidywać warunki wymiany ciepła w kanałach o małych średnicach.
-
Modeling of entrained flow steam gasification of sewage sludge
PublicationProper management of sewage sludge becomes increasingly problematic due to legal requirements aiming at diminishing environmental impact, as well as rationalizing the utilization from the point of view of logistics. Steam gasification of sewage sludge can result in very good quality of the producer gas. So far, the works have been focused on the gasification in fixed bed gasifiers. However, this does not allow to take full advantage...
-
Resonant and nonresonant excitation of waves in a planar magnetosonic flow
PublicationForced propagation of perturbations in a magnetosonic wave are considered. The driving force may be caused by stimulated Mandelstam–Brillouin scattering of optic waves or by intense magnetosonic exciter. Some heating-cooling function which takes into account radiative cooling and unspecified heating is taken into consideration, as well as nonlinearity of a medium. Both these factors make the excitation particular. The analytical...
-
Modeling lubricant flow between thrust-bearing pads
PublicationInlet temperature is one of the main inputs in all models for the analysis of fluid film bearing performance. At the same time, inlettemperature distribution and also oil velocity distribution at the inlet are the result of flow phenomena in the gap between the bearingpads. These phenomena are complex and in many cases further affected by any special arrangements of forced oil supply to the gapbetween pads. The reason for such...
-
Thermal heat-balance mode flow-to-frequency converter
Publication -
GENERALISED HERSCHEL MODEL APPLIED TO BLOOD FLOW MODELLING
PublicationThis paper introduces a new rheological model of blood as a certain generalisation of the standard Herschel-Bulkley model. This model is a rheological constitutive equation and belongs to the group of the so-called generalised Newtonian fluids. Experimental data is compared with results, obtained from the new model, to demonstrate that it allows for the best agreement together with Luo-Kuang model. The new model may be easily implemented...
-
Experimental Verification of Storm Sewer Transient Flow Simulation
PublicationThe paper focuses mainly on laboratory investigations of transient and transcritical flow in a single pipe of a sewer system. The aim of this paper is to present a comparison between pressure values calculated by an improved McCormack scheme and those measured at the hydraulic laboratory of the Gdansk University of Technology, which were observed inside a pipe in an experiment for water flow with pressurization. The analysis proves...
-
Alternative convolution approach to friction in unsteady pipe flow
PublicationIn the paper some aspects of the unsteady friction in pipe flow expressed by the convolution are analyzed. This additional term introduced into the motion equation involves the accelerations of fluid occurring in the past and a weighting function. The essence of such approach is to assume the appropriate form of weighting function. However, until now no fully reliable formula for this function has been found. To avoid some inconveniences...
-
Estimation of the steam condensation flow via CFD methods
PublicationThe results of numerical simulations to predict the performance of different steam models have been presented. All of the considered models of steam condensation have been validated on the base of benchmark experiment employing expansion in nozzle and next on the low pressure part of the steam turbine stage. For numerical analysis three models have been finally used – the ideal steam model without condensation, an equilibrium steam...
-
Pawlak's flow graph extensions for video surveillance systems
PublicationThe idea of the Pawlak's flow graphs is applicable to many problems in various fields related to decision algorithms or data mining. The flow graphs can be used also in the video surveillance systems. Especially in distributed multi-camera systems which are problematic to be handled by human operators because of their limited perception. In such systems automated video analysis needs to be implemented. Important part of this analysis...
-
Electrohydrodynamic secondary flow in the electrostatic precipitator with spiked electrodes
PublicationIn this work, the results of electrohydrodynamic (EHD) secondary flow measurements in an electrostatic precipitator (ESP) with one-sidedspike electrodes are presented. The EHD secondary flow was measured for one-sided spike electrodes with the spike tips directed either upstream or downstream the primary flow. The results showed different flow patterns for different spike tips direction in respect to the primary flow direction....
-
Acoustic heating produced in the thermoviscous flow of a Bingham plastic
PublicationThis study is devoted to the instantaneous acoustic heating of a Bingham plastic. The model of the Bingham plastic's viscous stress tensor includes the yield stress along with the shear viscosity, which differentiates a Bingham plastic from a viscous Newtonian fluid. A special linear combination of the conservation equations in differential form makes it possible to reduce all acoustic terms in the linear part of of the final equation...
-
Experimental investigations on condensation in flow in small diameter channels
PublicationW pracy przedstawiono innowacyjne podejście do eksperymentalnych badań kondensacji w przepływie oraz omówiono wstępne wyniki badań eksperymentalnych kondensacji etanolu w pionowej rurce srebrnej o średnicy wewnętrznej 2.3 mm.
-
An advanced Thermal-FSI approach to flow heating/cooling
PublicationActually, two-way thermal-energy exchange between working fluid and solid material of a casing is a leading problem for modern – semi automatic – design techniques. Many questions should be solved, especially, the turbulent mode of thermal energy transport both in fluid and solid, should be re-examined and reformulated from the primary principles. In the present paper, a group of researchers from Energy Conversion Department of...
-
A System for Cooling Electronic Elements with EHD Coolant Flow
PublicationA system for cooling electronic components where the liquid coolant flow is forced with ion-drag type EHD micropumps was tested.
-
EXPERIMENTAL AND THEORETICAL FLOW OF THE FORCES IN DEEP BEAMS WITH CANTILEVAR
PublicationThis article presents the results of experimental research carried out on deep beams with cantilever which was loaded throughout the depth. The main deep beam was directly simply supported on the one side. On the other side the deep beam was suspended in another deep member situated at right angles. All deep beams created a spatial arrangement. The paper is focused on the analysis of the cracks morphology and flow of the internal...
-
River flow simulation based on the HEC-RAS system
PublicationThis work considers the problem of river floods, and presents a computer solution that can be used to predict such a threat. The basic tool, called Hydrologic Engineering Centers for River Analysis System (HEC-RAS), and created by the US Army Corps of Engineering, is well developed; and the models created in the system HEC-RAS are quite realistic. For the purpose of solving practical national flood problems, simplified static and...
-
River Flow Simulation Based on the HEC-RAS System
PublicationThis work considers the problem of river floods, and presents a computer solution that can be used to predict such a threat. The basic tool, called Hydrologic Engineering Centers for River Analysis System (HEC-RAS), and created by the US Army Corps of Engineering, is well developed; and the models created in the system HEC-RAS are quite realistic. For the purpose of solving practical national flood problems, simplified static and...
-
A Concept of Freight Traffic Flow Regulations in the City of Gdansk
PublicationThis paper presents a review of state-of-art efforts in urban freight transport modelling in the context of their requirements and applicability as a basis for evaluation of city's freight transport policy. Freight transport mirrors all aspects of the city's economic activity and for that reason its proper planning is of extreme importance. However, urban freight system may be considered as the most varied and fragmented element...
-
Experimental study on the seepage flow through the ice jam
PublicationIn light of the observed climate change, there is a need for better understanding of river ice processes for managing water resources in the cold regions. Ice jams produce significant resistance which may cause rise of water level and flooding. The jam resistance is only referred to the roughness of its underside, and this approach lead to exceptional roughness coefficients which has no physical explanation. Number of evidences...
-
CFD analysis of fluid flow through the labyrinth seal
PublicationSteam and gas turbines are some of the fundamental means of power generation. The energy efficiency of the turbines, however, is not satisfactory. Ever since the start-up of the first turbine in the world, engineers have been striving for their increased efficiency. Multiple solutions to the problem of steam loss in an operating turbine are available. The use of seals is one of them. Empirical methods or numerical calculations...
-
Spetiation of organic matter in Vertical Flow Constructed Wetlands
PublicationThe object of the research were VFCWs which are a component of biological treatment of two hybrid hydrophyte systems located in Wieszyno and Wiklino, close to Słupsk, Poland. The facilities that are subject to analyses are unified in terms of structure (filtration material, depth of the bed and time of operation), but they differ in organic matter load, amounting respectively to: 8.0 gCOD/m2day and 31.0 gCOD/m2day.The intensity...
-
Analytical Steady-State Model of the Pipeline Flow Process
PublicationThe paper addresses the issue of modeling the flow process in transmission pipelines. A base model used for numerical simulation is introduced. Under certain assumptions concerning steady state analysis, the differential equations describing the process are solved analytically for two cases: zero and nonzero inclination angle α. These equations describe a constant flow rate and a corresponding distribution of the pressure along...
-
Discrete-continuous optimisation of an axial flow blood pump
PublicationThis paper presents results of discrete-continuous optimisation of an axial flow blood pump. Evolution Strategies (ES) are used as a global optimisation method in order to localise the optimal solution in relatively short time. The whole optimisation process is fully automated. This also applies to geometry modelling. Numerical simulations of the flow inside the pump is performed by means of the Reynolds-Average Navier-Stokes...
-
Graphene field-effect transistor application for flow sensing
PublicationMicroflow sensors offer great potential for applications in microfluidics and lab-on-a-chip systems. However, thermal-based sensors, which are commonly used in modern flow sensing technology, are mainly made of materials with positive temperature coefficients (PTC) and suffer from a self-heating effect and slow response time. Therefore, the design of novel devices and careful selection of materials are required to improve the overall...
-
Acoustic heating produced in the thermoviscous flow of a bingham plastic
PublicationThis study is devoted to the instantaneous acoustic heating of a Bingham plastic. The model of the Bingham plastic's viscous stress tensor includes the yield stress along with the shear viscosity, which differentiates a Bingham plastic from a viscous Newtonian fluid. A special linear combination of the conservation equations in differential form makes it possible to reduce all acoustic terms in the linear part of of the final equation...
-
Material Flow Analysis in a cooked mussel processing industry
PublicationGalicia (NW Spain) is an ideal environment for mussel culture owing to its excellent natural conditions. It is the first Spanish and European mussel producer and the second worldwide after China. More than 50% of the mussel collected in Galicia is used in the processing industry, which produces different products, as cooked mussel that is canned, frozen or used in the food industry. In this paper a methodology based on Life Cycle...
-
Educational Dataset of Handheld Doppler Blood Flow Recordings
PublicationVital signals registration plays a significant role in biomedical engineering and education process. Well acquired data allow future engineers to observe certain physical phenomena as well learn how to correctly process and interpret the data. This dataset was designed for students to learn about Doppler phenomena and to demonstrate correctly and incorrectly acquired signals as well as the basic methods of signal processing. This...
-
Flow maldistribution and its mitigation in mini heat exchangers
PublicationIn the present paper, a detailed numerical investigation has been carried out to analyze the flow maldistribution in 50 parallel 1 mm x 1 mm rectangular minichannels and 1 mm depth minigap section with rectangular, trapezoidal, triangular or concave mani-folds in Z-type flow configuration (16 different cases). The working medium was ethanol and the mass flow rate was 5×10-4 kg/s. Both sections was heated from the bottom side. Heat...
-
Inverse Flood Routing Using Simplified Flow Equations
PublicationThe paper considers the problem of inverse flood routing in reservoir operation strategy. The aim of the work is to investigate the possibility of determining the hydrograph at the upstream end based on the hydrograph required at the downstream end using simplified open channel flow models. To accomplish this, the linear kinematic wave equation, the diffusive wave equation and the linear Muskingum equation are considered. To achieve...
-
Analysis of the radiation dose in UV-disinfection flow reactors.
PublicationTheoretical considerations devoted to the variation of UV radiation doses in flow disinfection reactors are presented. The minimal time required by the fluid to pass the reactor was determined and combined with the radiation intensity. The active zones of the reactor were determined.
-
Steady magnetohydrodynamic flow in a diverging channel with suction or blowing
PublicationAn analysis is made of steady two-dimensional divergent flow of an electrically conducting incompressible viscous fluid in a channel formed by two non-parallel walls, the flow being caused by a source of fluid volume at the intersection of the walls. The fluid is permeated by a magnetic field produced by an electric current along the line of intersection of the channel walls. The walls are porous and subjected to either suction...
-
Silo music - mechanism of dynamic flow and structure interaction
PublicationArtykuł omawia zjawisko muzyki silosowej. Wykonano pomiary dynamiczne przyspieszeń, częstotliwości i postaci drgań własnych. Zaproponowano nowa hipotezę powstawania efektów dynamicznych podczas przepływu silosowego.
-
Reduction of dynamic effects during granular flow in silos
PublicationOmówiono kilka efektywnych sposobów redukcji nadmiernych dynamicznych efektów występujących w przepływie silosowym w silosach modelowych. Sposoby te mogą być wykorzystane w praktyce silosowej.
-
Silo music - mechanism of dynamic flow and structure interaction
PublicationArtykuł omawia zjawisko muzyki silosowe. Wykonano pomiary dynamiczne przyspieszeń, częstotliwości i postaci drgań własnych. Zaproponowano nowa hipotezę powstawania efektów dynamicznych podczas przepływu silosowego.
-
Confined granular flow in silos : experiments and numerical investigation
PublicationW monografii opisano niektóre charakterystyczne zjawiska mające miejsce podczas przepływów silosowych materiałów sypkich. Wykonano badania doświadczalne oraz obliczenia numeryczne celem wyjaśnienia zjawisk. Doświadczenia wykonano w dużych i małych silosach. Obliczenia wykonano przy zastosowaniu metody elementów skończonych opartej na hipoplastycznym modelu konstytutywnym dla materiałów sypkich.
-
Dynamic and tomography analysis of granular flow in cylindrical shell
PublicationW pracy przedstawiono wyniki badań ekperymentalnych dotyczących efektów dynamicznych występujących podczas przepływu materiałów sypkich w silosie cylindrycznym.
-
Application of a cellular automaton to simulations of granular flow in silos
PublicationA cellular automaton based on a gas model of hydrodynamics was used to calculate the kinematics of non-cohesive granular materials during confined flow in a mass flow and funnel flow model silo. In the model, collisions of particles were taken into account during granular flow. In addition, a simplified automaton was used wherein granular flow was assumed as an upward propagation of holes through a lattice composed of cells representing...
-
ANALYSIS OF POSSIBILITIES FOR THE USE OF VOLUME-DELAY FUNCTIONS IN THE PLANNING MODULE OF THE TRISTAR SYSTEM
PublicationTravel time is a measure commonly used for traffic flow modelling and traffic control. It also helps to evaluate the quality of traffic control systems in urban areas. Traffic control systems that use traffic models to predict changes and disruptions in vehicle flows have to use vehicle speed-prediction models. Travel time estimation studies the effects of traffic volumes on a street section at an average speed. The TRISTAR Integrated...
-
A system for acoustic field measurement employing cartesian robot
PublicationA system setup for measurements of acoustic field, together with the results of 3D visualisations of acoustic energy flow are presented in the paper. Spatial sampling of the field is performed by a Cartesian robot. Automatization of the measurement process is achieved with the use of a specialized control system. The method is based on measuring the sound pressure (scalar) and particle velocity (vector) quantities. The aim of the...
-
Regulator przepływu
PublicationW artykule opisano konstrukcję i wyniki badań prototypu regulatora przepływu charakteryzującego się brakiem sprężyny. W regulatorze zawór różnicowy zastąpiono zaworem stosunku ciśnień. Charakterystyki przepływowe regulatora mają przebieg niezależny od obciążenia. Nastawa regulatora odbywa się poprzez obrót hydrostatycznie odciążonej tulei dławiącej, wewnątrz której umieszczony jest suwak główny i suwak pomocniczy zaworu stosunku...
-
Numerical Analysis of Flow in Building Arrangement: Computational Domain Discretization
Publication -
NP-hardness of compact scheduling in simplified open and flow shops
Publication -
Power flow in typical series-parallel hybrid filters topologies
Publication -
Modelling of energy flow in mechatronic systems. A bond graph approach
PublicationW referacie przedstawiono w sposób jednoliy modelowanie systemów mechatroniki metodą grafów wiązań (GW) w aspekcie symulacji przepływu energii. Omówiono ogólne założenia modelowania w ujęciu GW. Modelowanie przepływu energii rozważano na przykładzie napędu pojazdu hybrydowego PH-MAK.
-
Determination of selected parameters in a 1D open channel flow model
PublicationOkreślenie parametrów jest ważnym etapem tworzenia modelu matematycznego. W przypadku jednowymiarowego modelu przepływu ze swobodną powierzchnią opisanego układem równań de Saint-Venanta, jedną z grup parametrów wymagających identyfikacji są parametry związane z tarciem. Mogą one być określone w różny sposób, ale w większości przypadków problem ten stanowi zagadnienie żle postawione. W takich przypadkach najczęściej stosowaną...
-
Effect of flow-rate on ethanol separation in membrane distillation process
Publication -
Electrical capacitance tomography for studying the flow of friable materials in silos.
PublicationArtykuł opisuje możliwość aplikacji tomografii do pomiarów przepływu materiałów sypkich w silosach
-
Horizontal flow boiling of refrigerants inside porous coated tube.
PublicationPrzedstawiono wyniki badań przejmowania ciepła i spadku ciśnienia podczas wrzenia czynników chłodniczych R22, R134a i R407C w poziomej rurce z wewnętrzną powłoką porowatą.
-
Application of time-frequency methods for analysis of dynamic silo flow
PublicationW artykule przedstawiono możliwość stosowania metod czasowo-częstotliwościowych w analizie dynamicznego przepływu materiału sypkiego w silosie. W pracy omówiono wyniki FT (Fourier Transform), STFT (Short Time Fourier Transform) oraz WT (Wavelet Transform)