Filters
total: 1593
filtered: 1385
displaying 1000 best results Help
Search results for: ENGINE ROTATION SPEED
-
Reduction of the reaction torque of an in-line four-cylinder four-stroke engine
PublicationW pracy przedstawiono zarówno dokładne jak i uproszczone zależności na przebieg momentu reakcyjnego silnika, jedno i wielocylindrowego, przenoszonego na ramę pojazdu lub fundament. Wyprowadzono zależność na wartość przesunięcia wałków wyrównoważających zapewniającą całkowite wyeliminowanie wpływu sił bezwładności na przebieg momentu reakcyjnego w silnikach czterosuwowych czterocylindrowych. Wprowadzono kryteria doboru optymalnej...
-
Research on the phenomena of warming up and free cooling down the car engine
PublicationThe average cold start temperature in Europe is 9 degrees C. However, not the average is the most important for the composition of exhaust gases and associated air pollution. The most onerous for the environment are the winter starts when automotive emissions of harmful gases add up in cities with those of home heating systems. The paper presents preliminary studies of warming up and cooling down processes in various environmental conditions....
-
Failure model of main elements of the ship engine crankshaft-piston assembly
PublicationThe paper presents a failure model of main elements of the crankshaft-piston assembly, based on failures ofcrankshaft-piston assembly and timing gear system of the Sulzer RD engines, retrieved from the equipment reliabilitydata of selected ships.
-
On Deck Oil Spill Clean-Up Materials – Solution for Engine Rooms
Publication -
Particle rotation effects in Cosserat-Maxwell boundary layer flow with non-Fourier heat transfer using a new novel approach
Publication -
Thioamides and selenoamides with chirality solely due to hindered rotation about the C-N bond: enantioselective complexation with optically active hosts
PublicationBariera rotacji wokół wiązania C-N w tioamidach jest średnio o 3-5 kcal/mol wyższa niż w odpowiednich amidach, a w analogicznych selenoamidach wzrasta jeszcze o 1 kcal/mol. Dzięki temu związki te występują w dwu enancjomerycznych formach, których wzajemna przemiana zachodzi w wyniku rotacji wokół wiązań C-N. Bariera rotacji jest wystarczająco wysoka, aby można było podjąć próbę ich rozdziału na enancjomery w temperaturze pokojowej....
-
The influence of screw configuration and screw speed of co-rotating twin screw extruder on the properties of products obtained by thermomechanical reclaiming of ground tire rubber
PublicationThe results of our investigations on the process of continuous thermomechanical reclaiming of ground tire rubber (GTR) carried out using a twin screw extruder are presented.We used a co-rotating twin screw extruder with a special configuration of plasticizing unit, enabling generation of considerable shear forces. The influence of screw configuration and screw speed on breaking of chemical crosslink bonds contained in ground tire...
-
Speed sensorless nonlinear control of induction motor in the field weakening region
Publication -
Speed sensorless induction motor drive with motor choke and predictive control
PublicationArtykuł przedstawia układ napędowy z silnikiem indukcyjnym, zasilanym z falownika napięcia przy zastosowaniu filtru silnikowego. System pracuje bez czujnika prędkości obrotowej. Głównym aspektem pracy jest zwrócenie uwagi na to, że zastosowanie dławika silnikowego wymaga odpowiednich zmian w strukturach sterowania i estymacji zmiennych. Zaproponowano odpowiednie rozwiązanie dla układu napędowego z regulatorem predykcyjnym prądu....
-
Innovative optimization algorithm of variable speed pumps in district heating systems.
PublicationW referacie przedstawiono innowacyjny algorytm matematyczny optymalizacji pracy pomp zmienno prędkościowych w systemach ciepłowniczych. Algorytm wykorzystuje procedurę iterecyjnego wyznaczania parametrów pracy pomp, których charakterystyki są linearyzowane odcinkami w układzie dwóch współrzędnych. Do rozwiązania modelu całkowitoliczbowego zaproponowano wykorzystanie systemu GAMS. W pracy przedstawiono podstawy metodologiczne i...
-
High speed milling vibration surveillance using modal model of the tool
PublicationPraca poświęcona jest nadzorowaniu drgań wirujących narzędzi w nowoczesnych frezarkach. Przedmiotem rozważań jest proces frezowania szybkościowego smukłym frezem kulistym na 5-osiowym centrum obróbkowym Deckel Maho DMU 50eVolution. Frezowanie smukłymi narzędziami jest często stosowane w przypadku nowoczesnych centrów obróbkowych. Uzasadnienie technologiczne wynika z konieczności dokładnego wykonywania złożonych kształtów geometrycznych...
-
Mechatronic design for the high speed milling surveillance of the complex and flexible details
PublicationW pracy przedstawiono mechatroniczny system tworzenia mapy optymalnych prędkości obrotowych wrzeciona. W trakcie frezowania szybkościowego przedmiotów podatnych mogą wystąpić drgania samowzbudne typu chatter. Używana zazwyczaj procedura ustawiania wymaganej prędkości obrotowej wrzeciona metodą prób i błędów, w wielu przypadkach nie jest zalecana. Przedstawiona procedura nadzorowania może doprowadzić do uniknięcia ryzyka wystąpienia...
-
Effect of FSW Traverse Speed on Mechanical Properties of Copper Plate Joints
Publication -
Surface roughness analysis of hardened steel after high‐speed milling
Publication -
Energy conversion in small water plants with variable speed PM generator
Publication -
Small Hydropower Plant With Integrated Turbine-Generators Working at Variable Speed
Publication -
Synchronized six-step voltage generation in high-speed PMSM drive
PublicationSynchronized voltage generation has already been considered in the context of pulse width modulation (PWM). References prove that synchronized PWM substantially decreases subharmonics in inverter output voltage when operating with low switching-to-fundamental frequency ratio. This paper identifies problems of unsynchronized voltage generation in electric drives under six-step inverter operation. Guidelines for the synchronization...
-
The experimental identification of the dynamic coefficients of two hydrodynamic journal bearings operating at constant rotational speed and under nonlinear conditions.
PublicationHydrodynamic bearings are commonly used in ship propulsion systems. Typically, they are calculated using numerical or experimental methods. This paper presents an experimental study through which it has been possible to estimate 24 dynamic coefficients of two hydrodynamic slide bearings operating under nonlinear conditions. During the investigation, bearing mass coefficients are identified by means of a newly developed algorithm....
-
The Influence of Stretch Rod Speed on the Relationship between Preblown Bottle Aesthetic Quality and Final Blown Bottle Thickness Profile in Stretch Blow Molding from Preform Process
PublicationFrom a mechanical point of view, the aesthetic quality of preblown PET bottles and thickness profile of final blown PET bottles manufactured in ISBM process are determined by mechanical and thermal response of blown preforms. From the microscopic point of view the biggest influence on the mechanical and thermal properties of PET bottles have orientation and crystallization processes. From a technological point of view, the aesthetic...
-
The time of the first transition of the semi-Markov process in the evaluation of diesel engine operation
PublicationW referacie przedstawiono rozwinięcie prezentowanej w literaturze metody ilościowej oceny działania na przykładzie okrętowego silnika głównego z zapłonem samoczynnym. Według tej interpretacji, działanie silnika może zostać przedstawione jako wielkość fizyczna. W tym aspekcie, na przykładzie okrętowego silnika napędu głównego dokonano oceny przydatności tej wielkości do opisu własności niezawodnościowych silnika. Precyzyjne określenie...
-
Spectral criterion for high-cycle fatigue of engine parts under asymmetricrandom load
PublicationPrzedstawiono kryterium ograniczonej trwałości zmęczeniowej wysokocyklowej części silników poddanych stacjonarnemu obciążeniu stochastycznemu o niezerowej wartości średniej. Wyznaczono naprężenie równoważne w postaci procesu okresowego w sensie średnio kwadratowym i zastosowano równanie Goodmana/So-derberga. Ukazano wpływ rozciągającego naprężenia resztowego na wartość oczekiwaną czasu do chwili uszkodzenia zmęczeniowego.
-
Selected problems of planning machinery and devices location in a ship´s engine room.
PublicationPrzedstawiono podstawowe zasady rozplanowania maszyn i urządzeń w przedziale maszynowym na statku. Podano warunki i kryteria wpływające na proces projektowania rozmieszczenia maszyn i urządzeń w siłowni. Przedstawiono główne warunki i zasady dotyczące rozplanowania głównego układu napędowego, elektrowni, kotłowni pomocniczych oraz innych instalacji siłownianych.
-
Dual fuelling of truck CI engine with diesel oil and mixture of propane and butane
PublicationW artykule przedstawiono zasadę działania dwupaliwowego zasilania jednocześnie olejem napędowym i odparowanym LPG silnika samochodu ciężarowego. Pokazano korzyści wynikające ze zużycia tańszego paliwa zbadane doświadczalnie.
-
Diagnostic model of compression-ignition engine slide bearings for controlling the changes of their state
PublicationW artykule przedstawiono koncepcję umożliwiającą sterowanie procesami zmian stanów eksploatacyjnych silnika na podstawie modelu diagnostycznego łożysk ślizgowych. Jako model łożyska ślizgowego przyjęty został topologiczny model diagnostyczny, pozwalający na pełne i dokładne wykorzystanie oleju smarowego jako jednego z nośników informacji o stanie technicznym łożyska. Przedstawiona została przykładowa interpretacja stanów eksploatacyjnych...
-
INFLUENCE OF THE MARINE 4-STROKE DIESEL ENGINE MALFUNCTIONS ON THE NITRIC OXIDES EMISSION
Publication -
Fault Tree Analysis and Failure Diagnosis of Marine Diesel Engine Turbocharger System
Publication -
Loads of ship main diesel engine in the aspect of practical assessment of its operation
PublicationW artykule przedstawiono koncepcję metody pozwalającej na ocenę działania silnika pracującego na obciążeniu częściowym. Do określenia istniejącego zapasu parametrów użytkowych silnika oraz związanych z degradacją jego stanu technicznego dodatkowych kosztów ponoszonych przez użytkownika wykorzystane zostało wartościujące (ilościowe) ujęcie działania interpretowanego jako pewna wielkość fizyczna.
-
Dependence of the toxic components exhaust emission from the car engine starting temperature
PublicationW publikacji opisano wyniki badań empirycznych zależności stężeń toksycznych składników spalin od stanu cieplnego silnika w chwili rozruchu. Zwrócono uwagę na duże stężenia w pierwszych kilkudziesięciu sekundach po rozruchu. Badano silniki samochodów osobowych zarówno w eksploatacji jak i na hamowni podwoziowej.
-
State-of-the-art framework for high-speed camera and photogrammetric use in geometry evaluation of prestressed concrete failure process
PublicationPrestressed structures are a key to the realization of the boldest architectural ideas, regardless of shape complexity, great height and large span. A characteristic feature of the prestressed structure is the better use of concrete material properties by insertion of internal forces. The internal forces are opposed to external loads effects (forces and deformations of structure). Prestressed reinforced concrete beams are characterized...
-
Fpga implementation of the two-stage high-speed fir filter in residue arithmetic
Publicationw pracy przedstawiono implementację szybkiego, dwustopniowego kaskadowego filtru fir w technologii fpga z użyciem arytmetyki resztowej. zastosowanie arytmetyki resztowej pozwala na uzyskanie dużych częstotliwości potokowania w związku z użyciem małych mnożników. zalety arytmetyki resztowej są ograniczane w pewnym stopniu koniecznością wykonywania skalowania po pierwszym stopniu filtru celem uniknięcia nadmiaru arytmetycznego. w...
-
An improved high-speed residue-to-binary converter based on the chinese remainder theorem
Publicationw pracy zaprezentowano nowy szybki konwerter z systemu resztowego do systemu binarnego. Projekcje ortogonalne wyznaczane są przy użyciu funkcji logicznych pięciu zmiennych. Suma projekcji obliczana jest z zastosowaniem drzewa Wallace'a. Wektor sumy i wektor przeniesienia są dzielone na segmenty tak aby liczba reprezentowana łącznie przez obydwa segmenty o młodszych wagach nie przekraczała zakresu systemu resztowego,M. Bity segmentów...
-
Innovative Energy-Saving Propulsion System for Low-Speed Biomimetic Underwater Vehicles
Publication -
Innovative Energy-Saving Propulsion System for Low-Speed Biomimetic Underwater Vehicles
Publication -
Simulation and Experiments of High Speed Machining Vibration Monitoring with Variable Spindle Velocity
PublicationArtykuł poświęcony jest nadzorowaniu drgań wirujących narzędzi podczas obróbki szybkościowej na nowoczesnych centrach frezarskich. Przeprowadzono analizę dynamiki procesu skrawania smukłym frezem kulistym. W celu zredukowania drgań zastosowano, z powodzeniem, zmienną prędkość obrotową narzędzia. Badania symulacyjne dotyczące efektywności proponowanej metody zostały potwierdzone wynikami badań eksperymentlanych na frezarce Alcera...
-
Efficiency analysis of an energy conversion system for a variable speed small hydropower plant
Publication -
Step on It Bringing Fullwave Finite-Element Microwave Filter Design up to Speed
PublicationThere are many steps in the design of a microwave filter: mathematically describing the filter characteristics, representing the circuit as a network of lumped elements or as a coupling matrix, implementing the distributed elements, finding the initial dimensions of the physical structure, and carrying out numerical tuning using electromagnetic (EM) simulators. The whole process is painstaking and time-consuming, and it requires...
-
FPGA realization of high-speed multi-stage FIR filter in residue arithmetic
PublicationW pracy przedstawiono implementację szybkiego wielostopniowego, kaskadowego filtru FIR w technologii FPGA. Zastosowanie arytmetyki resztowej pozwala na uzyskanie dużych częstotliwości próbkowania w zwiżaku z użyciem małych mnożników. Zalety wynikające z uzycia arytmetyki resztowej sa w pewnym stopniu ograniczne koniecznością wykonania skalowania przy kaskadowym połaczeniu filtrów FIR, tak aby uniknąć nadmiaru arytmetycznego. W...
-
On the possible increasing of efficiency of ship power plant with the system combined of marine diesel engine, gas turbine and steam turbine in case of main engine cooperation with the gas turbine fed in parallel and the steam turbine
PublicationW pracy przedstawiono koncepcję układu kombinowanego okrętowego dużej mocy złożonego z wiodącego silnika głównego spalinowego silnika tłokowego i skojarzonych z nim turbiny gazowej mocy i układu turbiny parowej, wykorzystujących energię zawartą w spalinach wylotowych głównego silnika spalinowego. Rozpatrzono wariant układu kombinowanego, w którym główny jest silnik tłokowy skojarzony z turbiną gazową mocy i układem turbiny parowej,...
-
On the possible increasing of efficiency of ship power plant with the system combined of marine diesel engine, gas turbine and steam turbine in case of main engine cooperation with the gas turbine fed in series and the steam turbine
PublicationW pracy przedstawiono koncepcję układu kombinowanego okrętowego dużej mocy złożonego z wiodącego silnika głównego silnika spalinowego tłokowego oraz skojarzonych z nim turbiny gazowej mocy i układu turbiny parowej, wykorzystujących energię zawartą w spalinach wylotowych silnika spalinowego. Rozpatrywano wariant układu kombinowanego, którym turbina mocy jest zasilana szeregowo spalinami wylotowymi. Podano algorytm i obliczenia...
-
Using Long-Short term Memory networks with Genetic Algorithm to predict engine condition
PublicationPredictive maintenance (PdM) is a type of approach for maintenance processes, allowing maintenance actions to be managed depending on the machine's current condition. Maintenance is therefore carried out before failures occur. The approach doesn’t only help avoid abrupt failures but also helps lower maintenance cost and provides possibilities to manufacturers to manage maintenance budgets in a more efficient way. A new deep neural...
-
Investigation of Exhaust Emissions from DI Diesel Engine During Cold and Warm Start
Publication -
Using LSTM networks to predict engine condition on large scale data processing framework
Publication -
Exhaust Emission from Passenger Cars During Engine Cold Start and Warm-Up
Publication -
Evaluation of methods for determining the combustion ignition delay in a diesel engine powered by liquid biofuel
Publication -
CBR methodology application in an expert system for aided design ship's engine room automation
PublicationW artykule przedstawiono metody obliczania podobieństwa na podstawie przypadków, zastosowane w opracowanym systemie ekspertowym do wspomagania projektowania siłowni okrętowej. Do realizacji metody na przykładzie automatyki napędu głównego zastosowano oprogramowanie bazy danych i system ekspertowy. Uzyskane wyniki wyszukiwania w bazie danych statków podobnych zostały porównane i przeanalizowane. Do weryfikacji zastosowanych w bazie...
-
An Experimental Study of Emission and Combustion Characteristics of Marine Diesel Engine with Fuel Injector Malfunctions
Publication -
NOx emission from a two-stroke ship engine: Part 2 – Laboratory test
Publication -
NOx emission from a two-stroke ship engine. Part 1: Modeling aspect
Publication -
An experimental study of emission and combustion characteristics of marine diesel engine with fuel pump malfunctions
Publication -
Dissipated energy minimization in a combustion engine Mount system by position dependent damping coefficients
PublicationPraca opisuje rozważania na temat możliwości tłumienia drgań spalinowego silnika czterosuwowego. Do modelowania wykorzystano zasady dynamiki układów wielomasowych. Przedstawiono krótki opis wspomnianego sposobu modelowani. Zbudowano model numeryczny silnika. Model poddano analizie numerycznej. Podczas analizy dynamiki układu skoncentrowano się na elementach tłumiących drgania, obecnych w zawieszeniu silnika oraz na analizie wpływu...