Search
Search results for: MEASUREMENT METHODS, TYRE/ROAD NOISE, TYRE LABEL
-
FTIR spectroscopic and thermogravimetric characterization of ground tyre rubber devulcanized by microwave treatment
PublicationIn this work, the phenomena involved in the microwave devulcanization of ground tyre rubber (GTR) were investigated. Three types of GTR with different content of organic compounds (elastomers, plasticizers, etc.), carbon black and ash have been studied. The chemical structure of GTR before and after a microwave devulcanization process was analyzed by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA)...
-
Poroelastic Road Surface – a Promising Road Traffic Noise Abatement Solution
PublicationRoad surfaces have a direct impact on the generation of noise by rolling tyres, the main and dominant source of noise of moving vehicles, as well as may affect propagation of noise emitted by all noise sources of a vehicle. Thus there is no doubt that pavement should be considered as one of the major potential road traffic noise abatement measure. Low noise pavements of existing types may in new conditions provide up to 8 dB of...
-
Speed dependency of temperature effects on road traffic noise
PublicationRecently, a new literature review on the influence of temperature on tire/road noise became available, based on a compilation of large amounts of data from empirical research. This review showed that the effect of temperature is roughly double of that previously assumed and taken account of in international standards. This makes temperature one of the main sources of error in measurement results. Furthermore, it suggested that...
-
Tire/Road Noise On Poroelastic Road Surfaces - Results Of Laboratory Measurements
PublicationTire/road noise is the most important part of traffic noise for medium and high speed driving both in the case of passenger cars and trucks. The potential to make modification of tires that significantly reduce tire/road noise in nearly over, at least for conventional tires so the only promising action is to improve road pavements. One of the innovative solutions is poroelastic road pavement (PERS) that reduces airflow related...
-
Ultra Low Noise Poroelastic Road Surfaces
PublicationNoise is one of the most important environmental problems related to road traffic. During the last decades, the noise emitted by the engines and powertrains of vehicles was greatly reduced and tires became a clearly dominant noise source. The article describes the concept of low noise poroelastic road surfaces that are composed of mineral and rubber aggregate bound by polyurethane resin. Those surfaces have a porous structure and...
-
Sound quality metrics applied to road noise evaluation
PublicationRoad noise monitoring systems typically measure sound levels in specific time periods. The more insightful approach suggests to measure also the nature of noise. Sound quality of sounds such as car noise can be objectively evaluated by several parameters. One of them is psychoacoustic annoyance, described by loudness, tone color, and the temporal structure of sound. In this paper the assessment of several sound quality parameters, such...
-
A pin-on-disc study of airborne wear particle emissions from studded tyre on concrete road contacts
PublicationStudded tyres wear surfaces of winter roads, generating inhalable airborne particles. In this study, four concrete road materials and two stud geometries were investigated in terms of wear, road material hardness and airborne particle concentration. The sliding contact between studded tyres and road materials was studied using a pin-on-disc machine in a clean chamber. The results show that the normal load and the stud size have...
-
Experimental investigation of performance and emission characteristics of a miniature gas turbine supplied by blends of kerosene and waste tyre pyrolysis oil
PublicationFossil fuels are non-renewable sources of energy that could be depleted in the near future, giving rise to amajor energy crisis. Scientists from all over the world are working on new technologies to produce fuelnot only from renewable sources but also from waste. This article is concerned with: (i) waste tyremanagement by means of the pyrolysis process, (ii) investigation of physico-chemical parameters ofwaste tyre pyrolysis oil...
-
Biological hazards in low noise, poroelastic road surfaces
PublicationDrainage pavements as well as poroelastic pavements ("PERS") are a very efficient way to decrease traffic noise by reducing tire/road noise at the source as well as noise propagation over the road surface. Many noise generating mechanisms at the tire/road interface are very much reduced by road porosity (pipe resonance, "air pumping", Helmholtz resonance and the horn effect). A well-designed porous or poroelastic road surface may...
-
Strength characteristics of tyre chips-sand mixtures.
PublicationBadania w aparacie trójosiowego ściskania przy różnej zawartości wagowej kawałków zużytych opon oraz różnym ich ułożeniu w próbce piasku. Badania prowadzono przy dowolnym ułożeniu tych elementów, umieszczeniu ich poziomo oraz w systemie mieszanym. Wyznaczono optymalną zawartość kawałków opon w próbce piasku, przy której występowała maksymalna wytrzymałość na ściskanie.
-
EVALUATION OF SOUND QUALITY FEATURES ON ENVIRONMENTAL NOISE EFFECTS – A CASE STUDY APPLIED TO ROAD TRAFFIC NOISE
PublicationThe paper shows a study on the relationship between noise measures and sound quality (SQ) features that are related to annoyance caused by the traffic noise. First, a methodology to perform analyses related to the traffic noise annoyance is described including references to parameters of the assessment of road noise sources. Next, the measurement setup, location and results are presented along with the derived sound quality features....
-
Investigation of the road noise source employing an automatic noise monitoring station
PublicationThe paper presents a pilot investigation of noise source models in two selected localizations in the context of future dynamic noise map creation. The experiments were carried out using the automatic noise monitoring station engineered at the Multimedia Systems Departmentof the Gda´nsk University of Technology. The results of the noise measurements employing monitoring stations and its comparison to the reference values are depicted....
-
Temperature influence on tire/road noise evaluated by the drum method
PublicationAmbient air and road surface temperatures substantially affect the road vehicle noise emission. The temperature influence on tire/road noise depends mainly on tire-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tires. The correction procedures for temperature effect are still under consideration and preparation. Laboratory experiment was prepared to...
-
Low Noise Poroelastic Road Pavements Based On Bituminous Binder
PublicationTire/road noise is the dominant source of traffic noise. It depends both on the tire design and on the characteristics of road pavements as well as on the vehicles’ operating conditions. Due to the fact that conventional (pneumatic) car tires have almost reached the limits of their ability to further reduce their noisiness, it is widely believed that the additional reduction of tire noise will be possible mainly through modifications...
-
The Methods for RTS Noise Identification
PublicationIn the paper authors present two methods, which allows to identify the RTS noise in noise signal of semiconductor devices. The first one was elaborated to identify the RTS noise and also to estimate the number of its levels. The second one can be used to estimate all of the parameters of Gaussian and non-Gaussian components in the noise signal in a frequency domain.
-
Effectiveness of Concrete Reinforcement with Recycled Tyre Steel Fibres
Publication -
TIRE/ROAD NOISE AND TIRE ROLLING RESISTANCE ON PROTOTYPE PERS SURFACE
PublicationPoroelastic road surfaces are characterized by low noise of tires running on them.Road pavements of this type are promising solution to problems related to traffic noise in cities and on rural roads. Some technical problems still have to be solved, in particular regarding durability and skid resistance on wet surface. Ongoing and planned works are to contribute to create a quiet, durable and safe road surface, which will become...
-
Low noise poroelastic road pavements based on modified asphalt binder
PublicationTire/road noise is one of the most important environmental problems related to road traffic. As the most effective way to fight noise is reduction of sound emission from the source, a lot of work is being done to improve tire and road surfaces construction. This paper describes the first “road” results obtained within the SEPOR project, which is focused on developing a low noise poroelastic road surface based on bituminous binder....
-
Economical methods for measuring road surface roughness
PublicationTwo low-cost methods of estimating the road surface condition are presented in the paper, the first one based on the use of accelerometers and the other on the analysis of images acquired from cameras installed in a vehicle. In the first method, miniature positioning and accelerometer sensors are used for evaluation of the road surface roughness. The device designed for installation in vehicles is composed of a GPS receiver and...
-
Methods of trend removal in electrochemical noise data – overview
PublicationIn this paper we shall review popular methods of trend removal from electrochemical noise time records. The basic principles of operation of the six most popular methods are explained. The proposed methods are: high - pass filtering, Moving Average Removal, polynomial detrending, wavelet detrending, Empirical Mode Decomposition and Variational Mode Decomposition. Estimation of trend removal quality...
-
Characteristics of tyre chips-sand mixtures from triaxial tests
PublicationAnaliza parametrów wytrzymałościowych i odkształcalności mieszanek piasku i kawałków zużytych opon. Powtórne użycie tego materiału, odpowiednio przetworzonego na skrawki i elementy o kształcie kołowym pozwala po odpowiednim zmieszaniu z gruntem niespoistym na uzyskanie materiału o zwiększonej wytrzymałości na ścinanie zachowywanej również przy dużych odkształceniach. Analizowano mieszanki o różnej zawartości opon przy naprężeniach...
-
Evaluation of recycled tyre steel fibres adhesion to cement matrix
Publication -
Methods of Assessing Degradation of Supercapacitors by Using Various Measurement Techniques
PublicationThis article presents the qualitative analyses of the construction of supercapacitor samples. The analyses are based on the suggested thermographic measurements as well as the technique of testing the inherent noise of the investigated element. The indicated assessment methods have been referred to the currently used parameters for the qualitative evaluation of supercapacitors. The approach described in this paper, which introduces...
-
Modeling the effect of electric vehicles on noise levels in the vicinity of rural road sections
PublicationNumerous European countries experience a steady increase in the share of electric (EV) and hybrid electric (HEV) vehicles in the traffic stream. These vehicles, often referred to as low- or zero-emission vehicles, significantly reduce air pollution in the road environment. They also have a positive effect on noise levels in city centers and in the surroundings of low-speed roads. Nevertheless, issues related to modeling noise from...
-
Rolling Resistance And Tire/Road Noise on Rubberized Asphalt Pavement In Poland
PublicationThe paper presents results of tire/road noise and rolling resistance measurements performed on stone-matrix asphalt (SMA) that contains rubberized asphalt developed and produced by the company in Poland. Bituminous binder was modified with polymer and additive of crumb rubber. First observations of asphalt mixture with the new kind of modified bitumen used on the field section are presented. Rolling resistance of passenger car...
-
METHODS OF TEACHING NOISE PROTECTION AT ENVIRONMENTAL ENGINEERING
PublicationNoise strongly influences both our health and behavior in everyday life and as employees or employers. The lost of hearing and other effects of noise on humans result not only in a significant decrease in the quality of life or work efficiency but have also have economic consequences. As noise can be preventable in part by the Environmental Engineers, but it is necessary to introduce them noise issues during their education process....
-
Inhomogeneity of low-noise wearing courses evaluated by tire/road noise measurements using the close-proximity method
PublicationPerforming numerous analyses of tire/road noise measurements on low-noise pavements during the last several years, the authors observed significant inhomogeneity of the wearing course in numerous cases, while similar problems were almost non-existent when dense pavements were measured. Three main causes of low-noise pavement inhomogeneity can be defined. The first one is imperfections in the technology used for asphalt mix production...
-
Flicker Noise in Resistive Gas Sensors—Measurement Setups and Applications for Enhanced Gas Sensing
PublicationWe discuss the implementation challenges of gas sensing systems based on low-frequency noise measurements on chemoresistive sensors. Resistance fluctuations in various gas sensing materials, in a frequency range typically up to a few kHz, can enhance gas sensing by considering its intensity and the slope of power spectral density. The issues of low-frequency noise measurements in resistive gas sensors, specifically in two-dimensional...
-
Comparison of the tests for equivalence of the measurement methods for measurement of PM10 dust in ambient air
PublicationThe paper presents the motives for conducting the equivalence tests and the reasons of discrepancies between the results of PM10 dust concentration obtained via the reference method and the methods based on 'on-site' measurement. The reference and non-reference methods of measurement of PM10 dust concentration in air have been discussed. Field tests for equivalence, following the Polish standard and the European Union (EU) guidelines,...
-
Laser-textured cross-hatched surface topography analysis with evaluation of high-frequency measurement noise
PublicationThe precision of surface roughness determination using ISO 25178 parameters relies on various factors that directly impact the measurement process. In industry applications, the contactless roughness measurement reduces data collection time. However, it introduces several potential errors, including those stemming from the environment. One of the main types of errors encountered during topography analysis is measurement noise,...
-
A review of design approaches for the implementation of low-frequency noise measurement systems
PublicationElectronic noise has its roots in the fundamental physical interactions between matter and charged particles, carrying information about the phenomena that occur at the microscopic level. Therefore, Low-Frequency Noise Measurements (LFNM) are a well-established technique for the characterization of electron devices and materials and, compared to other techniques, they offer the advantage of being non-destructive and of providing...
-
An in-depth look at the tire rubber hardness influence on tire/road noise measurements
PublicationWhen assessing the acoustic quality of a road pavement with the close-proximity (CPX) or the on-board sound intensity (OBSI) method, the rubber hardness of the reference tire substantially affects the measurement. Practical experience shows that measurement tires can get significantly harder within a single measurement season. This is why one would like to normalize measurements to a reference rubber hardness. The recently published...
-
A method of two-terminal excess noise measurement with a reduction of measurement system and contact noise
PublicationPrzedstawiono metodę i system do pomiaru szumów nadmiarowych dwójników elektrycznych ze znaczną redukcją wpływu szumów własnych systemu pomiarowego i szumów kontaków. Proponowana metoda może byc zastosowana do pomiaru szumów elementów z wyprowadzonymi końcówkami, bądź też struktur, gdy jako wzorcowy szum odniesienia może zostać zastosowany szum struktury rezystywnej wytworzonej bezpośrednio na strukturze w otoczeniu elementu testowanego.
-
Measurement methods for assessing insulation condition of underground pipelines
PublicationThe paper discusses the most frequently applied measurement methods for assessing the quality of external insulation along pipelines and detecting defect locations in the protective coating. The quality of coating along a given pipeline section under investigation is assessed by determining unitary resistance of the coating, which is calculated on the basis of measurement results obtained along a pipeline subjected to cathodic...
-
The contribution of tire/road noise to the overal noise of cars and motocycles
PublicationOmówiono wływ hałasu opon i hałasu jednostki napędowej na całkowity hałas generowany przez pojazd. Zaprezentowano opracowany w Katedrze pojazdów i Maszyn Roboczych PG program VENOM do symulacji halasu pojazdów w ruchu drogowym. Przy pomocy tego programu określono wpływ zmiennych warunków ruchu drogowego na hałas generowany przez pojazd. Uwzględnioino przyspieszanie na poszczególnych biegach, hamowanie z różnymi prędkościami oraz...
-
Mechanical Performance and Environmental Assessment of Sustainable Concrete Reinforced with Recycled End-of-Life Tyre Fibres
PublicationThe presented research’s main objective was to develop the solution to the global problem of using steel waste obtained during rubber recovery during the tire recycling. A detailed comparative analysis of mechanical and physical features of the concrete composite with the addition of recycled steel fibres (RSF) in relation to the steel fibre concrete commonly used for industrial floors was conducted. A study was carried out using...
-
Comparison of noise reduction methods in radiometric correlation measurements of two-phase liquid-gas flows
PublicationTwo-phase liquid-gas flows occur frequently in the mining, energy, chemical, and petrochemical industries. One of non-contact methods used to analyse these flows is the gamma ray absorption method. However, the signals received from radiation detectors contain a significant stochastic noise, which makes them difficult to analyse. The article describes four methods of noise reduction in cross-correlation measurements of water-air...
-
Stability analysis of a road scarp in the Carpathian Mountains and methods of its protection
PublicationThe purpose of the study was to analyse the stability of a road scarp endangered by a landslide and to consider some measures for its stabilization. The potential landslide could unfavourably alter the shape of the slope, thus a religious sanctuary situated above the slope. The present research has resulted in suggestions of possible protection methods, namely, drainage, soil nailing, installation of piles, supporting the scarp...
-
Low-power device simulator for micro-energy measurement methods testing
PublicationThe paper presents low-power device simulator designed for testing of micro-energy measurement methods. Such kind methods can be used for evaluation of power systems based on Energy Harvesting. The device allows to set the current consumption characteristic over the time, thus making possible playing the role of different types of low-power devices e.g. simulating sensor network node.
-
Topography measurement methods evaluation for entire bending-fatigued fracture surfaces of specimens obtained by explosive welding
PublicationIn this paper, the methods of compensation of differences in the results of entire bending-fatigued fracture surface topographies were presented. The roughness evaluation was performed with a focus variation microscope and confocal surface topography measurement techniques. The differences in the ISO 25178 roughness parameters were investigated and procedures for their compensation were studied. It was found that various types...
-
Web Based Acoustic Noise Measurement System.
PublicationW referacie przedstawiono projekt multimedialnego systemu przeznaczonego do monitorowania zagrożeń hałasem środowiskowym. Nadrzędnym celem realizowanego projektu jest zwiększenie efektywności profilaktyki chorób słuchu. Opracowywany system umożliwia odbiór, przechowywanie danych, analizę i wizualizację wyników pomiarów hałasu pozyskanych od urządzeń pomiarowych za pośrednictwem Internetu. Przedstawiono również opracowanie miernika...
-
Detection of measurement noise in surface topography analysis
Publication -
Assessment of the Speed Management Impact on Road Traffic Safety on the Sections of Motorways and Expressways Using Simulation Methods
PublicationMethods used to evaluate the impact of Intelligent Transport System (ITS) services on road safety are usually based on expert assessments or statistical studies. However, commonly used methods are challenging to apply in the planning process of ITS services. This paper presents the methodology of research using surrogate safety measures calculated and calibrated with the use of simulation techniques and a driving simulator. This...
-
Noise measurement setups for fluctuations enhanced gas sensing
PublicationObserwacje zjawisk fluktuacyjnych w sensorach gazów pozwala zwiększyć czułość i selektywność detekcji gazów. Problemem jest budowa prostego i taniego systemu do obserwacji tych zjawisk. W artykule przedstawiono dwa systemy pozwalające na obserwacje szumów w rezystancyjnych sensorach gazów dostępnych na rynku i prototypowych, wykonanych z warstwy nanocząstek o zbliżonych wymiarach.
-
Selective monitoring of noise emitted by vehicles involved in road traffic
PublicationAn acoustic intensity probe was developed measures the sound intensity in three orthogonal directions, making possible to calculate the azimuth and elevation angles, describing the sound source position. The acoustic sensor is made in the form of a cube with a side of 10 mm, on the inner surfaces of which the digital MEMS microphones are mounted. The algorithm works in two stages. The first stage is based on the analysis of sound...
-
Directivity of tire/road noise emission for selected tires and pavements
PublicationPraca pośwoęcona jest kierunkowości emisji hałasu opon i nawierzchni drogowych. Opony są dominującym źródłem haasu w pojaździe poruszającym się w typowych warunkach ruchu drogowego. Hałas ten nie jest bezkierunkowy jak to przyjmuje się w modelach obliczeniowych hałasu. Takie założenia wynikają z ograniczonej dostępności danych dotyczących kierunkowości i mogą prowadzić do niedokładności przy prognozowaniu hałasu drogowego. Praca...
-
Discrete identification of continuous non-linear and non-stationary dynamical systems that is insensitive to noise correlation and measurement outliers
PublicationThe paper uses specific parameter estimation methods to identify the coefficients of continuous-time models represented by linear and non-linear ordinary differential equations. The necessary approximation of such systems in discrete time in the form of utility models is achieved by the use of properly tuned `integrating filters' of the FIR type. The resulting discrete-time descriptions retain the original continuous parameterization...
-
Prevention methods and tools in road designing and maintenance
PublicationSpośród wielu systemowych elementów zarządzania bezpieczeństwem infrastruktury drogowej, wyróżnić można cztery rodzaje działań mające charakter prewencyjny, a mianowicie: Ocena oddziaływania na bezpieczeństwo ruchu, Audyt bezpieczeństwa ruchu drogowego, Zarządzanie bezpiecezństwem sieci drogowej i Przeglądy dróg. Działania te, jako środki prewencyjne w projektowaniu i eksploatacji dróg powinny stanowić spójny system ocen projektowanych...
-
New methods of underwater ship noise classification
PublicationDetekcja, klasyfikacj, identyfikacja i rozpoznanie cech hałasu generowanego przez statki jest bardzo istotna z punku widzenia naukowego i obronnego. Włożono wiele wysiłku w rozwój technologii sonarów pasywnych, która umożliwia zastosowanie hałasów podwodnych do celów praktycznych. Przedstawiono wyniki badań, które ukazują możliwości wykorzystania sieci neuronowej do klasyfikacji źródeł generowanych przez układy mechaniczne, odpowiadających...
-
Methods of measurement signal acquisition from the rotational flow meter for frequency analysis
PublicationOne of the simplest and commonly used instruments for measuring the flow of homogeneous substances is the rotational flow meter. The main part of such a device is a rotor (vane or screw) rotating at a speed which is the function of the fluid or gas flow rate. A pulse signal with a frequency proportional to the speed of the rotor is obtained at the sensor output. For measurements in dynamic conditions, a variable interval between...