Search
displaying 1000 best results Help
Search results for: DRY BEARING MATERIALS
-
Study of the Influence of Heat Convection Coefficient on Predicted Performance of a Large Tilting-Pad Thrust Bearing
PublicationPart of the heat generated by the shearing of the lubricating film during operation of a hydrodynamic bearing is transferred to the bearing components. In the case of the pad, which is usually fully submerged in the lubricating oil, heat is further transferred at the pad free walls to the oil by convection. This mechanism causes a thermal gradient in a pad and, consequently, its thermal deflection. In large hydrodynamic thrust...
-
Nanotechnologies in Development of Structural Materials and Biomaterials
PublicationThe nanometric materials and technologies resulted in nanostructures are reviewed. The examples of nanomaterials are shown. The typical nanotechnologies, including plastic deformation, mechanical attrition, controlled detonation, hot plasma jet synthesis, laser vaporisation, CVD and PVD, mechanical milling, annealing, ultrasonic irradiation, nanolithography, electrocrystallisation, electrospinning, sol-gel method, cryogenic laser-enhanced...
-
Improvement of Thrust Bearing Calculation Considering the Convectional Heating within the Space between the Pads
PublicationA modern thrust bearing tool is used to estimate the behavior of tilting pad thrust bearings not only in the oil film between pad and rotating collar, but also in the space between the pads. The oil flow in the space significantly influences the oil film inlet temperature and the heating of pad and collar. For that reason, it is necessary to define an oil mixing model for the space between the pads. In the bearing tool, the solutions...
-
Analysis of sloping brace stiffness influence on stability and load bearing capacity of a truss
PublicationThe paper is focused on the numerical study of stability and load bearing capacity of a truss with side elastic braces. The structure is made in reality. The rotational and sliding brace stiffnesses were taken into account. Linear buckling analysis and non-linear static analysis with geometric and material nonlinearity were performed for the beam and shell model of the truss with respect to the angle of sloping braces. As a result...
-
Impact of Spatial Noise Correlation on Bearing Accuracy in DIFAR Systems
PublicationDIFAR type underwater passive systems are one of the more commonly used tools for detecting submarines. At the design stage, which usually uses computer simulations, it is necessary to generate acoustic noise of the sea. It has been shown that correlating noise significantly reduces these errors compared to the assumption that noise is uncorrelated. In addition, bearing errors have been shown to be the same in systems with a commonly...
-
Effect of presence of lifting pocket on the THD performance of a large tilting-pad thrust bearing
PublicationHydrostatic assistance is a commonly used method to improve limited load carrying ability of tiltingpad thrust bearings during transient states of operation of vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves, etc.), it also requires manufacturing of special recesses/pockets at pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up...
-
Running characteristics of aerodynamic bearing with self-lifting capability at low rotational speed
PublicationAn aerodynamic journal bearing that is capable of self-generating squeeze-film pressure is presented and its dynamic characteristics investigated numerically and experimentally. A numerical method based on a time marching static model was applied to assess the orbit trajectory path of the rotor upon a perturbation. Experimental results were obtained to validate the effect of the self- generated squeeze-film pressure on the stability...
-
Monitoring of occupational exposure to volatile organohalogen solvents (VOXs) in human urine samples of dry-cleaner workers by TLHS-DAI-GC-ECD procedure
PublicationChlorinated hydrocarbon solvents are often used for dry-cleaning clothes in the laundry industry. The object of this study was to monitor the occupational exposure of dry-clean employees coming into contact with VOXs. 25 workers collected their urine samples before the work shift, after 4 hours of work and after the work shift. The analyses of urine samples and solvents used in dry-cleaning were performed using TLHS-DAI-GC-ECD....
-
Influence of an applied bearing system on behaviour of multi-span footbridge
PublicationThe cycle overpass in Gdynia is a box structure over 300 metres long, 10-span. It was opened for bicycle traffic in the second half of 2013. At the end of its construction, there was failure due to excessive horizontal displacement of the system. A number of bearings exceeded the range of permissible transverse shifts thus it was necessary to temporarily protect the spans from slipping. The FEM analysis of the original solution...
-
Progress in ATRP-derived materials for biomedical applications
PublicationThe continuing wave of technological breakthroughs and advances is critical for engineering well- defined materials, particularly biomaterials, with tailored microstructure and properties. Over the last few decades, controlled radical polymerization (CRP) has become a very promising option for the synthesis of precise polymeric materials with an unprecedented degree of control over mo lecular architecture. Atom transfer radical...
-
Justifying the prolongation of the service life of the bearing structure of a tank car when using Y25 bogies
PublicationThis paper substantiates the use of Y25 bogies under tank cars in order to prolong their service life. The reported study has been carried out for a tank car with rated parameters, as well as the actual ones, registered during full-scale research. Mathematical modeling was performed to determine the basic indicators of the tank car dynamics. The differential equations of motion were solved by a Runge-Kutta method using the Mathcad...
-
Experimental comparison of the transition speed of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublicationA journal bearing test bench is used to find the transition speed between the hydrodynamic and mixed lubrication regimes for a modified magnetorheological (MR) fluid. It is shown that the transition speed of the bearing can be reduced by applying a local magnetic field near minimum film when it is lubricated with the MR fluid, and that this will only marginally increase friction. The lubricating performance of the MR fluid is compared...
-
ADVANCES IN MATERIALS SCIENCE EDITORIAL ON THE JOURNAL'S 20th ANNIVERSARY
PublicationEditorial on the occasion of the 20th anniversary of Advances in Materials Science journal.
-
STRENGTH of MATERIALS TOWARDS APPLICATIONS (2024)
e-Learning CoursesThe SMTA DATE Course consists of the following problems to be discussed during the lectures: - Introduction to strength of materials towards applications - Fundamentals of modelling in strength of materials towards applications - Materials and basic structures - Fundamentals of modelling in strength of materials towards applications - Definition of environment and loads - General, energy-based and advanced methods for analysis...
-
Estimation of Screw Displacement Pile-Bearing Capacity Based on Drilling Resistances
PublicationThis article presents an engineering, empiricalmethod of estimating the bearing capacity and settlementcharacteristics Q-s of screw displacement piles andcolumns, based on soil resistance encountered during thedrilling to form piles/columns in the ground. The methodwas developed on the basis of correlation analyses of thetest results of 24 piles made during the “DPDT-Auger”research project (Krasiński et al., 2022a). In the proposedmethod,...
-
Bearing estimation using double frequency reassignment for a linear passive array
PublicationThe paper demonstrates the use of frequency reassignment for bearing estimation. For this task, signals derived from a linear equispaced passive array are used. The presented method makes use of Fourier transformation based spatial spectrum estimation. It is further developed through the application of two-dimensional reassignment, which leads to obtaining highly concentrated energy distributions in the joint frequency-angle domain...
-
Reducing common mode voltage and bearing currents in quasi - resonant DC - link inverter
PublicationIn the paper, a concept of separation of an inverter-fed induction motor drive from its mains supply by two transistor switches inserted in the dc-link circuit is reexamined based on the proposed parallel quasi-resonant dc-link inverter (PQRDCLI). The objective of the paper is to show an advantage of the proposed topology in limiting high frequency common mode voltage and bearing currents. In the laboratory setup, an induction...
-
ANALYSIS OF BEARING CLEARANCE AND WIDTH OF OIL GROOVE ON CHARACTERISTIC OF FLUID FILM IN HYDRODYNAMIC MAIN CRANKSHAFT BEARINGS
PublicationAbstract Paper represents analysis of influence of oil groove width and bearing clearance on characteristics of oil film in hydrodynamic journal main crankshaft bearing. Analysis was performed in purpose to define influence of bearing clearance and dimensions of oil groove on static characteristics and manufacturability of half shelf bearings in industrial high-volume production. Computer simulations was made using ARTbear program...
-
Effect of manufacturing errors of the pad sliding surface on the performance of the hydrodynamic thrust bearing
PublicationIn the present study, investigation of the effect of manufacturing errors on the performance of large tilting pad thrust bearings has been performed, following a CFD-based Thermohydrodynamic analysis of a single pad. A 3D model has been generated, including the pad, the lubricant film and the corresponding part of the collar. The pad has been assumed to be deformed about the pivot point, due to thrust loading. Manufacturing errors...
-
Chapter 2: Modelling and analysis of rotor with magnetic bearing system
PublicationThe paper is concerned with rotor magnetic bearing system modelling. Such system is a relatively complex electromechanical system and can be considered as typical mechatronic one. The port-based modelling of physical systems has been used to obtain discrete-continuous model of considered system. Proposed approach enables to obtain reduced low-order lumped parameter representation of the system including gyroscopic interactions....
-
Applied Mechanics and Materials
Journals -
ANALYSIS OF THE LOAD-CARRYING CAPACITY OF A HYDRODYNAMIC WATER-LUBRICATED BEARING IN A HYDROELECTRIC POwER PLANT
PublicationThe paper presents an analysis of the load-carrying capacity of a historic hydrodynamic water-lubricated radial bearing of an unconventional segment design installed in the Braniewo Hydroelectric Power Plant. The aim of the calculations was to determine whether the bearing operates in the conditions of hydrodynamic or mixed lubrication, as well as to establish the optimal geometry of the axial grooves allowing for the highest load-carrying...
-
Evaluation of expanded uncertainty of instantaneous power measurement in a bearing diagnostic system.
PublicationThe paper presents the issues concerning the estimation of the expanded uncertainty in the system for the diagnosis of rolling bearings, consisting of transducers: voltage and current voltage, which is used for diagnostic bearing motors method based on the measurement and analysis of the instantaneous power signal consumed by the induction motor. It presents the methodology for assessing the measurement uncertainty and presents...
-
Experimental research on marine oil-lubricated stern tube bearing
PublicationBearings of propeller shafts are very crucial elements of the propulsion system of each of the ships. The safety of shipping depends on their durability and reliability. The new legal restrictions mean that today we are looking for environmentally friendly solutions. That is why water-lubricated bearings are becoming more and more popular. So, will oil-lubricated shaft bearings belong to the past? The bearing with a white metal...
-
Laboratory station for research of the innovative dry method of exhaust gas desulfurization for an engine powered with residual fuel
PublicationContemporary methods of exhaust gas desulfurization in marine engines are all expensive methods (4-5 million euro). This is, among other reasons, due to the limited market audience, but primarily due to the monop-olized position of manufacturers offering fabrication and assembly of this type of marine ship installations. Proposed as part of a research project financed by the Regional Fund for Environmental Protection and Maritime...
-
BIOGENIC AMINES IN DRY CURED MEAT PRODUCTS
Publication -
Common-Mode Voltage and Bearing Currents in PWM Inverters: Causes, Effects and Prevention
PublicationIn modern induction motor drives an increase of transistors' switching frequency and a decrease of switching times are the sources of some serious problems. The high dv/dt and the common mode voltage generated by the inverter PWM control results in the appearances of bearing currents, shaft voltages, motor terminal overvoltages, the decrease of motor efficiency, and electromagnetic interference. The aspects of common mode (CM)...
-
The use of GFRP tubes as load-bearing jackets in concrete-composite columns
PublicationThe paper presents the fields of applications of polymer composites in building structures. The use of composite glass fibre tubes is discussed in more detail. The laboratory methods used to test the mechanical properties of these pipes are presented. An original research program is presented, including six concrete-filled glass fibre tubes. The cylinders and columns made in this way were tested for their axial load capacity. Conclusions...
-
Tribological Properties of Thermoplastic Materials Formed by 3D Printing by FDM Process
PublicationThe dataset entitled 3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_4 contains: the time base (expressed in seconds and minutes), the friction torque for sliding friction, rotational velocity of the counter – specimen (velocity of sliding), friction coefficient, load in the friction contact...
-
Air journal bearing utilizing near-field acoustic levitation: stationary shaft case
PublicationResults of a study to examine a unique idea of self-levitating journal bearing are presented in this paper. the idea represents a radical departure from the current bearing technology. it utilisesacoustic levitation, which relies on the sound energy radiated by an object supporting a load. acoustic levitation has been demonstrated to support loads of up to 10 kg. in order to support a load theacoustic wave emitted by the radiating...
-
Underwater Processing of Materials
PublicationEditorial do SI
-
Journal of Materials Chemistry A
Journals -
Manufacturing Parameters, Materials, and Welds Properties of Butt Friction Stir Welded Joints–Overview
PublicationThe modern and eco-friendly friction stir welding (FSW) method allows the combination of even such materials that are considered to be non-weldable. The development of FSW technology in recent years has allowed a rapid increase in the understanding of the mechanism of this process and made it possible to perform the first welding trials of modern polymeric and composite materials, the joining of which was previously a challenge....
-
Shape Memory Polyurethane Materials Containing Ferromagnetic Iron Oxide and Graphene Nanoplatelets
PublicationIntelligent materials, such as memory shape polymers, have attracted considerable attention due to wide range of possible applications. Currently, intensive research is underway, in matters of obtaining memory shape materials that can be actuated via inductive methods, for example with help of magnetic field. In this work, an attempt was made to develop a new polymer composite—polyurethane modified with graphene nanoplates and...
-
Deep learning for ultra-fast and high precision screening of energy materials
PublicationSemiconductor materials for energy storage are the core and foundation of modern information society and play important roles in photovoltaic system, integrated circuit, spacecraft technology, lighting applications, and other fields. Unfortunately, due to the long experiment period and high calculation cost, the high-precision band gap (the basic characteristic parameter) of semiconductor is difficult to obtain, which hinders the...
-
Current-based higher-order spectral covariance as a bearing diagnostic feature for induction motors
PublicationConducting the diagnosis of induction motors remotely by analyzing the supply current is an attractive prospect with the lack of access to the engine. Currently, there is no solution, based on analysis of the current, the credibility of which would allow its use in industry. The statistics of bearing failures in induction motors indicate that they constitute more than 40% of induction motor damage, therefore, bearing diagnosis...
-
High-precision bearing estimation for active sonar with cylindrical array performed by interpolated array transformation
PublicationThe article presents a method for improving the accuracy of bearing in multibeam sonar with a cylindrical array. The antenna’s non-linear shape and the resulting non-uniform sampling of the signal in space, mean that known methods of high-resolution spectral analysis cannot be used. In order to apply an algorithm from this group, a linear virtual antenna must be produced. The paper presents a technique of mapping a cylindrical...
-
NEW ORGANIC MATERIALS FOR PHOTOVOLTAICS
PublicationThis report presents the results of investigations carried out for polymer- and low-weightmolecular materials prepared in the form of thin films by various methods, namely the thermalvacuum evaporation and chemical vapour deposition. The influence of the technologicalconditions on the structure, surface morphology, and electronic properties of selected organic thinfilms, including polyazomethines, phthalocyanines, and perylene...
-
Materials Science & Engineering C-Materials for Biological Applications
Journals -
Project of hip joint endoprothesis for an individual patient with materials selection
PublicationThis work includes the hip replacement design, based on the patient's medical records, the description of creation process and materials used for individual components.
-
Biopolymers in designing modern antimicrobial medical materials. Part I. Biopolymer medical materials - collagen, chitosan
PublicationThe article is a review of the literature concerning the possible use of biopolymers for the preparation of dressings with antimicrobial activity. Authors show the potential of biopolymers: collagen and chitosan - which have the ability to immobilize and control the release of various active compounds - for providing the appropriate antibacterial, bacteriostatic and wound healing properties. Types of threats, for which the dressing...
-
Effect of small quantities of potassium promoter and steam on the catalytic properties of nickel catalysts in dry/combined methane reforming
PublicationCarbon dioxide and methane are two of the principal greenhouse gases. Reduction of their content in the atmosphere is currently the subject of much worldwide research. Dry and combined reforming of methane are effective methods of CO2 and CH4 utilization and production of synthesis gas (syngas) in chemical technology. Testing of catalysts that provide the desired H2/CO ratio and long operation time is one of the critical aspects...
-
Ni-WC/Al2O3 and Ni-WC/MgWO4/MgAl2O4 catalysts for resource recovery via pyrolysis combined with the dry reforming of plastics (PCDR)
PublicationPlastic waste (PW) is currently one of an environmental threat. Despite the increasing share of recycled plastics, their disposal remains high. Therefore, there is a high demand for new PW management systems. Among them, pyrolysis combined with dry reforming (PCDR) is an advantageous solution because it allows for resource recovery in the form of gas and liquid fuels, with simultaneous utilization of CO2. To date, catalysts based...
-
Strenght of materials towards applications , PG_00053661
e-Learning CoursesThe course is dedicated to the DAPE WIMiO Students. From the theoretical point of view the course consists of the following problems to be discussed during the lectures: -fundamentals of strength of materials -basic structures and environment -loads on structures -strength of materials: tension, stress, analysis of stress and strain, bending moments and shearing forces, longitudinal and shearing stress in beams, bending stress...
-
Improvement of the thrust bearing calculation considering the convectional heating within the space between the pads
PublicationA modern thrust bearing calculation tool should consider not only the oil film between pad and rotating collar but also the space between the pads. The oil flow in the space has a significant influence on the oil film inlet temperature, the convectional cooling of pad and collar and should be included in the bearing calculation methods. The authors use a tool developed at Clausthal University of Technology in cooperation with the...
-
Materials science. Quantum particle approach. 2022.
e-Learning Coursesquantum methods for materials and molecular modeling.
-
Bearing capacity for random subsoil.
PublicationW pracy zaproponowano modyfikację metody charakterystyk bazującej na stochastycznej metodzie różnic skończonych. Podejście takie pozwoliło na uwzględnienie przestrzennej zmienności podłoża gruntowego przy ocenie nośności granicznej ławy fundamentowej posadowionej na losowym podłożu. Przeprowadzono analizę wpływu dyskretyzacji ośrodka gruntowego na rozwiązanie oraz rozpatrzono jego zbieżności.
-
N-doped carbon materials as electrodes for highly stable supercapacitors
PublicationThis article reports a strategy to use nitrogen-doped carbon materials as electrodes for supercapacitors. Depending on the carbon precursor, the porous structure is changed with specific surface area reached up to 2270 m2 g−1. The capacitance of carbon materials used as electrodes is related strictly to pore size. The microstructure and nitrogen functionalities enable a high capacitance (327 F g−1) and cycle durability. The nanoporous...
-
The Impact Of The Selected Parameters Of Fdm Manufacturing Technology On Tribological Performance Of Abs–Steel Pair Under Dry Friction
PublicationThe paper presents the result of tribological test of ABS and steel samples sliding under dry friction. Polymeric samples were manufactured of ABS material using FDM technology. Testing was carried out in unidirectional sliding in a ring-on-flat contact in a PT-3 tribometer. The scope of tested parameters included volumetric and mass wear, the friction coefficient, and polymeric specimen temperature. Polymeric specimens used in...
-
Advances in Functional Materials Summer School 2023
e-Learning CoursesOur summer school on “Advances in Functional Materials” aims to bring together young scientists (Ph.D. and MSc students) with renowned specialists in materials engineering. Experts from academia, research units, and industry will deliver lectures, tutorials, and laboratory classes so that you can practice what you have learned. We divided the program into five main thematic topics: 1) Superconducting materials, 2) Additive manufacturing, 3)...