Search
Search results for: pavement conditions
-
Comparison of road and laboratory measurements of tyre/road noise
PublicationTyre/road noise is one of the major environmental problems related to road traffic. There are several measuring methods of tyre/road noise that may be carried out on the road (for example Coast-down and Close Proximity Method) or in the laboratory (Drum Method). Road measurements are preferred for evaluations of pavement properties while laboratory methods are mostly used to evaluate tyres. One of the biggest problems associated...
-
Eco-friendly modification of bitumen: The effects of rubber wastes and castor oil on the microstructure, processability and properties
PublicationThe bitumen industry in the European Union is facing several difficulties, including rising demand, unstable oil supply, rising prices for synthetic polymer modifiers, and a focus on lowering carbon footprint. Bitumen modification with crumb rubber (CR) is one of the most promising solution to these challenges. However, CR-modified bitumen have poor processability and low storage stability. To overcome these flaws we are introducing...
-
Determination of equivalent axle load factors with the use of strain energy of distortion
PublicationThe paper proposes a new method for calculation of equivalent axle load factors based on the analysis of strain energy of distortion induced in road pavements by traffic loads. The main advantage of the method is the more accurate calculation of the effects of multiple axles and super single versus dual tyres. The methodconsiders the location of critical points, at which strain energy of distortion reaches extreme values. When...
-
Poroelastic Road Surfaces - State of The Art
PublicationPoroelastic Road Surfaces (PERS) constitute a specific group of pavements containing a great amount of crumbled rubber. In most cases rubber aggregate constitutes about 20% of the mixture (by weight) and a polyurethane resin is used as a binder. As a result, PERS is characterized by a much higher elasticity than asphalt and a high porosity typical for drainage pavements. Due to this, tire/road noise is greatly reduced and on top...
-
Complex modulus of Cement Bitumen Treated Material Mixture (28 days of curing at 20C)
Open Research DataDataset presents data of complex modulus determined for cold recycled mixture – cement bitumen treated material mixture with 3 combinations of binding agents: 2% cement, 6% emulsion (C2E6), 6% cement, 6% emulsion (C6E6), 6% cement, 2% emulsion (C6E2). Mixture was designed according to Polish requirements for the base course of pavement. Mixture contains...
-
Effect of Overloaded Vehicles on Whole Life Cycle Cost of Flexible Pavements
PublicationThe phenomenon of vehicle overloading—illegal exceeding of maximum legal weight of vehicles, is a serious problem both in developing and developed countries around the world. Overloaded vehicles occur less frequently in comparison to properly loaded vehicles but due to their greater potential to cause damage they significantly contribute to distress of pavement structure. As studies show, the number of overloaded vehicles increases...
-
Deformation Sweep Test of Cement Bitumen Treated Material Mixture C3E5.5 (field obtained material; over 28 days of curing at 20C)
Open Research DataDataset presents data of results of deformation sweep test determined for cold recycled mixture – cement bitumen treated material mixture with following binding agents: 3% cement and 5.5% emulsion (C3E5.5). Mixture was designed according to Polish requirements for the base course of pavement. Mixture contains 60% of RAP material. Specimen size: f=100...
-
Deformation Sweep Test of Cement Bitumen Treated Material Mixture C3E5.5 (field cores; field curing)
Open Research DataDataset presents data of results of deformation sweep test determined for cold recycled mixture – cement bitumen treated material mixture with following binding agents: 3% cement and 5.5% emulsion (C3E5.5). Mixture was designed according to Polish requirements for the base course of pavement. Mixture contains 60% of RAP material. Specimen size: f=100...
-
Comparison of low-temperature cracks intensity on pavements with high modulus asphalt concrete and conventional asphalt concrete bases
PublicationHigh modulus asphalt concrete (HMAC) base courses provide very good resistance to rutting and fatigue but they can increase the risk of low-temperature cracking as compared with conventional asphalt concrete (AC). The article presents the comparison of these two road materials in terms of low-temperature cracking. The statistical method based on the ordered logistic regression model was used. The analysis was based on results of...
-
Road texture influence on tyre rolling resistance
PublicationTyre performance, one of the critical factors for vehicle users, is strongly related to theroad surface characteristics, most notably to the pavement texture. Phenomena that occur at the tyre/road interface affect tyre friction (skid resistance), rolling resistance, tyre wear and tyre/road noise. This article deals with relationship between surface texture and rolling resistance of light and heavy vehicle tyres. Mean profile depth...
-
Quantifying the effective mobilized RAP content during hot in-place recycling techniques
PublicationThe utilization of in-place recycling techniques is capable of consuming 100% reclaimed asphalt pavement (RAP). Hot in-place recycling (HIR) is one of the promising techniques to rehabilitate the pavements suffering from minor cracking issues through heat scarification, additive injecting, mechanical mixing, and compacting. However, the main concern of using 100% RAP in HIR remains as how much RAP can be activated and mobilized...
-
ROSANNE Project: New Procedure for Noise Characterisation of Road Surfaces in Europe
PublicationROSANNE is a collaborative project in the 7th EU Framework Programme which aims at harmonising measurement methods for skid resistance, noise emission and rolling resistance of road pavements as a preparation for standardization. The project started in November 2013 and is developing and improving standards in the field of working group CEN/TC 227/WG 5. Regarding the influence of the pavement on the road traffic noise emission,...
-
Further development of the poroelastic road surface within the new Polish project SEPOR
PublicationRoad surfaces have a direct impact on noise generated by rolling tyres, the main and dominant source of noise of moving vehicles. Road surface texture, porosity and stiffness/elasticity govern the pavement contribution to tyre/road noise the most. An experimental PoroElastic Road Surface (PERS) is a wearing course with a high content of interconnected voids (pores) and with an elastic behavior due to the use of small particles...
-
Complex modulus of Cement Bitumen Treated Material Mixture C3E4 cores obtained from the field section (28-365 days of curing at the field and later in laboratory at 20C)
Open Research DataDataset presents data of complex modulus determined for cold recycled mixture – cement bitumen treated material mixture with following binding agents: 3% cement, 4% emulsion (C3E4). Mixture was designed according to Polish requirements for the base course of pavement. Specimen were obtained from the field at 28, 180, 270 and 365 days after compaction....
-
Audit of the existing surfaces /pavements of sidewalks and roads in the Gdańsk-Oliwa district, with particular emphasis on the location of the "Polanki" market and its direct neighbourhood in the contexts of pavement design of the "Polanki"market; stage from 2019 year.
Open Research DataThe document presents a valorization of paved surfaces (sidewalks and roads) in the Gdańsk-Oliwa district, prapared on the basis of an preliminary inventory work – 21 tables (one table for each street ) with a description of the street and materials used, mostly supplemented with photographic material. The valorization, after the initial inventory,...
-
Fatigue data of Cement Bitumen Treated Material Mixture C3E5.5 (over 28 days of curing at 20C)
Open Research DataFatigue data of Cement Bitumen Treated Material Mixture C3E5.5 (over 28 days of curing at 20C)
-
Complex modulus of Cement Bitumen Treated Material Mixture C3E5.5 (over 28 days of curing at 20C)
Open Research DataDataset presents data of complex modulus determined for cold recycled mixture – cement bitumen treated material mixture with following binding agents: 3% cement and 5.5% emulsion (C3E5.5). Mixture was designed according to Polish requirements for the base course of pavement. Mixture contains 60% of RAP material. Specimen size: f=100 mm, h=130 mm. Specimen...
-
Fatigue data of Cement Bitumen Treated Material Mixture C3E5.5 (over 28 days of curing at 20C, field cores)
Open Research DataDataset presents data of fatigue life determined for cold recycled mixture – cement bitumen treated material mixture with following binding agents: 3% cement and 5.5% emulsion (C3E5.5). Mixture was designed according to Polish requirements for the base course of pavement. Mixture contains 60% of RAP material. Specimen size: f=100 mm, h=48,4 - 70,9 mm.
-
Fatigue data of Cement Bitumen Treated Material Mixture C3E5.5 (Direct tension, over 28 days of curing at 20C)
Open Research DataFatigue data of Cement Bitumen Treated Material Mixture C3E5.5 (Direct tension, over 28 days of curing at 20C)
-
Impact of overloaded vehicles on load equivalency factors and service period of flexible pavements
PublicationOverloaded vehicles occur less frequently in comparison to properly loaded vehicles but due to their greater potential to cause damage they significantly contribute to the distress of pavement structure. As the studies show, the phenomena of vehicles overloading intensifies when the control of traffic is poor and the average percentage of overloaded vehicles on analyzed roads varies from 6% to 23%. The main goal of the ar-ticle...
-
Evaluation of thermal cracking probability for asphalt concretes with high percentage of RAP
PublicationThe paper presents determination of the probability of thermal cracking of asphalt mixtures with different reclaimed asphalt pavement (RAP) content on the basis of laboratory tests and analytical evaluation using thermal stress development method. Probability was evaluated taking into consideration: the type and gradation of the mixture and the quality and content of RAP. Thermal stresses were determined using two models: elastic and...
-
Methods of deep modification of low-bearing soil for the foundation of new and spare air runways
PublicationAfter analyzing the impact of aircraft on the airport pavement (parking spaces, runways, startways), it was considered advisable to consider the problem of deep improvement or strengthening of its subsoil. This is especially true for low-bearing soil. The paper presents a quick and effective method of strengthening the subsoil intended for the construction of engineering structures used for civil...
-
Effect of polymer fibres reinforcement on selected properties of asphalt mixtures
PublicationThe paper presents selected results of the research program concerning fibre reinforced asphalt concrete. Aramid-polyalphaolefin fibres was used in this study. Selected properties responsible for low temperature cracking and resistance to permanent deformation are presented in this paper. Low temperature cracking susceptibility was evaluated with the results obtained from bending test of rectangular beams with constant rate of...
-
Review and evaluation of cold recycling with bitumen emulsion and cement for rehabilitation of old pavements
PublicationThe article presents Polish experience with cold recycling of asphalt pavements with theusage of bituminous emulsion and cement. In the 1990s numerous roads in Polandrequired immediate reinforcement due to their significant degradation. Implementation ofthe cold recycling technology was one of the solutions to this problem. Cold recycledmixtures containebeside the recycled asphalt pavement and aggregateetwo differenttypes of binding...
-
Bus bays inventory using a terrestrial laser scanning system
PublicationThis article presents the use of laser scanning technology for the assessment of bus bay geo-location. Ground laser scanning is an effective tool for collecting three-dimensional data. Moreover, the analysis of a point cloud dataset can be a source of a lot of information. The authors have outlined an innovative use of data collection and analysis using the TLS regarding information on the flatness of bus bays. The results were...
-
Road surface roughness estimation employing integrated position and acceleration sensor
PublicationAssessment of a surface quality being an essential task for the authorities supervising the roads provides the subject of the paper. Information about riding quality of a pavement, important for drivers, both in terms of their comfort and safety is collected during experiments employing mobile sensors. The paper describes the use of a miniature position and acceleration sensor for evaluation of the roughness of the road surface....
-
The Influence of the Aircraft Operating Fluids on the Mechanical Parameters of the Airport Surface Concrete
PublicationThe authors of the article assessed the impact of operating fluids used to service aircraft on changing mechanical parameters of cement concrete intended for airport pavement. The research concerned concrete designed with the use of CEM I 42.5N LH NA low-alkali cement, broken granite aggregate, fine washed aggregate, and admixtures. The analysis included the assessment of changes in dierences in endurance parameters over various...
-
Application of Bayesian Networks in risk diagnostics arising from the degree of urban regeneration area degradation
PublicationUrban regeneration as a complex project, generates many extremely specific threats affecting the increase of investment risk. Its unique nature causes that probability parameter, normally applied in the process of risk quantification, is extremely difficult to estimate. Due to lack of historical data urban regeneration related activities are therefore associated with uncertainty. According to the authors, a useful tool for resolving...
-
Application of BN in Risk Diagnostics Arising from the Degree of Urban Regeneration Area Degradation
PublicationUrban regeneration as a complex project, generates many extremely specific threats affecting the increase of investment risk. Its unique nature causes that probability parameter, normally applied in the process of risk quantification, is extremely difficult to estimate. Due to lack of historical data urban regeneration related activities are therefore associated with uncertainty. According to the authors, a useful tool for resolving...
-
Fracture susceptibility of high RAP content asphalt concrete in terms of aging
PublicationDue to the reduction of CO2 emissions during the production of asphalt mixtures and the decrease in the demand for mineral resources, the addition of reclaimed asphalt pavement (RAP) is becoming indispensable. The durability of asphalt pavements containing a high RAP content may be reduced due to a decrease in the cracking resistance of the material, especially under the influence of operational aging. The article presents the...
-
Tire/Road Noise On Poroelastic Road Surfaces - Results Of Laboratory Measurements
PublicationTire/road noise is the most important part of traffic noise for medium and high speed driving both in the case of passenger cars and trucks. The potential to make modification of tires that significantly reduce tire/road noise in nearly over, at least for conventional tires so the only promising action is to improve road pavements. One of the innovative solutions is poroelastic road pavement (PERS) that reduces airflow related...
-
Characterization and properties of LDPE/(ground tire rubber)/crosslinked butyl rubber blends
PublicationIn recent years, interest in used rubber recycling, mainly focusing on the utilization of end-of-life tires, has heightened. This interest, is owing to the activities related to environmental protection and economic factors, which both stimulate companies to reuse the high-quality rubber present in ground rubber scrap. In this study, the application of crosslinked butyl rubber in thermoplastic compositions of low-density polyethylene...
-
Interlaboratory Test to Characterize the Cyclic Behavior of Bituminous Interlayers: An Overview of Testing Equipment and Protocols
PublicationThe performance assessment of multi-layered pavements strongly depends on the mechanical behavior of the interface between bituminous layers. So far, comprehensive studies have been carried out mainly using quasi-static laboratory tests focusing on the interlayer shear strength at failure. However, it is generally recognized that cyclic shear testing will lead to the determination of parameters which are more closely linked to...
-
The use of a two-phase Monte Carlo material model to reflect the dispersion of asphalt concrete fracture parameters
PublicationThe work covers comprehensive laboratory tests of semi-circular bending (SCB) of asphalt concrete samples. The results of two test series, including four and 32 SCB specimens, indicate a substantial scatter of force–deflection (F-d) histories. The numerical analysis is aimed to reflect the maximum breaking load and fracture energy of the samples, pointing out their random character. The original simulation-based fictitious Monte...
-
Recycled Polyethylene terephthalate (PET) as Construction Material in Civil Engineering: A Review
PublicationIn general, the quantity of plastics of all types consumed annually all over the world has been growing in a phenomenal way. The manufacturing processes, service industries and municipal solid wastes (MSW) generate numerous waste plastic materials. The increasing awareness about the environment has tremendously contributed to the concerns related with disposal of the generated wastes. It is believed that the management of solid...
-
ANALYSIS OF ROLLING RESISTANCE OF TIRES WITH RUN FLAT INSERT APPLYING DRUM METHOD AND RADIAL CHARACTERISTIC
PublicationThis paper presents analysis of rolling resistance of tires with RUN FLAT insert applying drum method and radial characteristic. The conducted studies indicated changes in operational properties of wheel, occurring as a result of inflation pressure drop in the wheel. As regards radial elasticity, such changes result in significant drop of radial rigidity and increase of static deflection and increase of tire rolling resistance....
-
The Application of Granulated Expanded Glass Aggregate with Cement Grout as an Alternative Solution for Sub-Grade and Frost-Protection Sub-Base Layer in Road Construction
PublicationThe purpose of the research was to assess the possibility of using granulated expanded glass aggregate (GEGA) with cement grout as a replacement of a sub-grade and frost-protection layer, made of natural fine aggregates (NATU), stabilized with a hydraulic binder. Instead of traditional parts of the road construction, such as the sub-grade and frost-protection layer with the application of fine aggregate, stabilized with cement,...
-
Accurate rolling resistance Rolling resistance measurements can be influenced by a number of factors
PublicationTire rolling resistance is one of the most difficult-to-measure parameters of the tire/ pavement interface, especially if road measurements are required. First of all, it is necessary to measure a fairly small force in the system that is heavily loaded by other forces and subjected to many adverse effects causing measurement errors. The second problem is related to the fact that tire rolling resistance depends on many factors,...
-
Interlaboratory Test to Characterize the Cyclic Behavior of Bituminous Interlayers: An Overview of Testing Equipment and Protocols
PublicationThe performance assessment of multi-layered pavements strongly depends on the mechanical behavior of the interface between bituminous layers. So far, comprehensive studies have been carried out mainly using quasi-static laboratory tests focusing on the interlayer shear strength at failure. However, it is generally recognized that cyclic shear testing will lead to the determination of parameters which are more closely linked to...
-
An in-depth look at the tire rubber hardness influence on tire/road noise measurements
PublicationWhen assessing the acoustic quality of a road pavement with the close-proximity (CPX) or the on-board sound intensity (OBSI) method, the rubber hardness of the reference tire substantially affects the measurement. Practical experience shows that measurement tires can get significantly harder within a single measurement season. This is why one would like to normalize measurements to a reference rubber hardness. The recently published...
-
Temperature influence on tyre/road noise of selected tyres
PublicationAir and road temperatures substantially affect road vehicle noise emission. The temperature influence on tyre/road noise depends mainly on tyre-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tyres. The correction procedures for temperature effect are still under consideration and preparation. Tyre/road noise measurements using CPX method were performed...
-
Evaluation of Asphalt Mixture Low-Temperature Performance in Bending Beam Creep Test
PublicationLow-temperature cracking is one of the most common road pavement distress types in Poland. While bitumen performance can be evaluated in detail using bending beam rheometer (BBR) or dynamic shear rheometer (DSR) tests, none of the normalized test methods gives a comprehensive representation of low-temperature performance of the asphalt mixtures. This article presents the Bending Beam Creep test performed at temperatures from −20...
-
The Use of Direct Shear Test for Optimization of Interlayer Bonding Under a Poroelastic Layer
PublicationPoroelastic Road Surfaces (PERS) are characterised by porous structure with air void content of 20% or higher and stiffness almost 10 times lower than that of a standard asphalt course. Such properties enable noise reduction by up to 12 dB in comparison to SMA 11 mixture. However, the disadvantage of a poroelastic pavement is its low durability, which partially results from delamination from the lower layer. The paper aims to investigate...
-
Bitumen-Based Poroelastic Pavements: Successful Improvements and Remaining Issues
PublicationThis article presents the development process of designing and testing poroelastic pavement based on highly polymer-modified bitumen. Poroelastic wearing course was composed of mineral and rubber aggregate mixed with highly polymer-modified bitumen, in contrast to previous trials, during which polyurethane resins were mainly used as binder, which led to several serious technological problems concerning difficult production, insufficient...
-
Determination of binder-aggregate adhesion by contact angle measurement
PublicationThe key factor in asphalt pavement durability, especially in the presence of water, is adhesion of the bituminous binder to mineral aggregates. There are currently no standard laboratory test procedures that can quickly and accurately measure the strength of the interaction (bond) between the binder and aggregate. In this regard, to evaluate the adhesion force measurements based on the contact angle between the binder and the aggregate...
-
The influence of road surface unevenness on tyre rolling resistance
PublicationThe geometric characteristics of road surface substantially affect the interaction between tyre and road. Depending on pavement texture wavelength, the texture chiefly affects tyre/road friction, rolling resistance, interior and exterior noise, tyre wear, and ride comfort. The article presents results of investigations on the influence of road surface unevenness on the rolling resistance of passenger car and truck tyres. The tests...
-
Advanced fatigue and rutting characterisation of Polish asphalt mixtures based on the VECD model and viscoplastic shift model
PublicationThe advanced asphalt mixture performance-related specifications (AM-PRS) recently developed in USA can allow an optimisation of the design process of asphalt pavements thanks to the possibility to fully take into account the intrinsic material properties. In this study, four typical Polish mixtures, i.e. a Stone Mastic Asphalt (SMA) for wearing course, two mixtures for binder course with neat bitumen or Polymer modified Bitumen...
-
The long-term properties of mineral-cement-emulsion mixtures
PublicationThis publication presents evaluation of long-term behavior of mineral-cement-emulsion (MCE) mixtures. MCE mixtures are among the major products of cold recycling of old asphalt pavements. They are composed by binding of the old materials reclaimed from the pavement and new mineral aggregate using two different binding agents – cement and bituminous emulsion. While bituminous emulsion dissolutes and binds materials quite fast, it...
-
Assessment of Thermal Stresses in Asphalt Mixtures at Low Temperatures Using the Tensile Creep Test and the Bending Beam Creep Test
PublicationThermal stresses are leading factors that influence low-temperature cracking behavior of asphalt pavements. During winter, when the temperature drops to significantly low values, tensile thermal stresses develop as a result of pavement contraction. Creep test methods can be suitable for the assessment of low-temperature properties of asphalt mixtures. To evaluate the influence of creep test methods on the obtained low-temperature...
-
Influence of Asphalt Binder on the Compactability of Asphalt Mixtures Using Locking Point
PublicationCompaction is an important process for the asphalt mixture service life. A properly compacted mixture is crucial for long-lasting pavement. The objective of this study was to evaluate the influence of asphalt binders on the compactability of the asphalt mixtures by utilizing the concept of the locking point. To achieve this objective, two compaction methods (impact and gyration), different temperatures and asphalt content, and...