Search
Search results for: titanium alloy ti13nb13zr
-
Investigation of the electrochemical behaviour of AA1050 aluminium alloy in aqueous alkaline solutions using Dynamic Electrochemical Impedance Spectroscopy
PublicationThe paper presents the electrochemical behaviour of aluminium alloy AA1050 in aqueous alkaline media in the pH range 14–8.5. Electrochemical study was applied in order to obtain comprehensive information on the mechanism and kinetics of the process of anodic dissolution of aluminium, supplemented by monitoring of surface topography using an electron microscope. The corrosion rate of AA1050 increases with increasing concentration...
-
Cyclic behavior of FeCoCrNiMn high entropy alloy coatings produced through cold spray
PublicationeCoCrNiMn high entropy alloy powders were employed to produce coatings on carbon steel through high pressure cold spray (at 1100 °C and 7 MPa in temperature and pressure respectively). X-ray diffraction of the sprayed material revealed a dense coating with the retention of the original crystallographic structure. Once splatted, particles revealed high flattening ratio with consequent excellent adhesion of the coating to the substrate....
-
Fracture surface formation of notched 2017A-T4 aluminium alloy under bending fatigue
PublicationThe effect of cyclic loading on facture surface topology in notched components made by aluminium alloys is not completely clear. Fractogra-phy and fracture mechanics can help to understand this interdependency. This paper aims to study the distribution of the fracture surface roughness of notched 2017A-T4 aluminium alloy after bending fatigue using an optical focus-variation surface measurement technique by applying the fracture...
-
Strain sequence effect on fatigue life and fracture surface topography of 7075-T651 aluminium alloy
PublicationThe paper studies the effect of strain-loading sequence on fatigue lifetime and fracture surface topographies in 7075-T651 aluminum alloy specimens. Fatigue tests were performed in two ways: (i) constant-amplitude loading and (ii) two series of variable amplitude loading with non-zero mean strain values. The topography of the fatigue fractures was measured over their entire surfaces with the help of an optical confocal measurement...
-
Artificial Neural Network based fatigue life assessment of riveted joints in AA2024 aluminum alloy plates and optimization of riveted joints parameters
PublicationThe objective of this paper is to provide the fatigue life of riveted joints in AA2024 aluminum alloy plates and optimization of riveted joints parameters. At first, the fatigue life of the riveted joints in AA2024 aluminum alloy plates is obtained by experimental tests. Then, an artificial neural network is applied to estimate the fatigue life of riveted lap joints based on the number of lateral and longitudinal holes, punch pressure,...
-
Topography and microstructure of phosphate-iron glasses containing niobium and titanium
Open Research DataThe topography and microstructure of phosphate-iron glasses containing niobium and titanium were investigated by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM). Glass samples of the composition of 35P2O5-30Fe2O3-(35-x)Nb2O5-xTiO2 where x= 0; 7.5 and 15 (in %mol) were prepared by the conventional melt quenching technique. Appropriate...
-
Photocatalytic decomposition of acetaldehyde over TiO2 (titanium dioxide) supported on nickel foam and Ni-doped (nickel-doped) TiO2
Open Research DataThis dataset contains chromatograms recorded during the decomposition of acetaldehyde in a high-temperature reaction chamber under UV irradiation using as photocatalytic systems TiO2 (titanium dioxide) supported on nickel foam, TiO2 supported on oxidized nickel foam and TiO2 doped by metallic nickel (Ni) powder. The detailed equipment and measurement...
-
Effects of Surface Pretreatment of Titanium Substrates on Properties of Electrophoretically Deposited Biopolymer Chitosan/Eudragit E 100 Coatings
PublicationThe preparation of the metal surface before coating application is fundamental in determining the properties of the coatings, particularly the roughness, adhesion, and corrosion resistance. In this work, chitosan/Eudragit E 100 (chit/EE100) were fabricated by electrophoretic deposition (EPD) and both their microstructure and properties were investigated. The present research is aimed at characterizing the effects of the surface...
-
Mono- and bimetallic (Pt/Cu) titanium(IV) oxide photocatalysts. Physicochemical and photocatalytic data of magnetic nanocomposites’ shell
PublicationSurface modification of titania with noble and semi-noble metals resulted in significant enhancement of photocatalytic activity. Presented data, showing the photocatalytic properties of TiO2-M (where M is Pt and/or Cu) photocatalysts were further used as Fe3O4@SiO2/TiO2-M magnetic nanocomposites shells in "Mono- and bimetallic (Pt/Cu) titanium(IV) oxide core-shell photocatalysts with Vis light activity and magnetic separability"...
-
Allergy to implant components: chromium, nickiel, cobalt and titanium
PublicationImplant jest kompozycja roznych pierwiastkow: niklu, chromu, kobaltu, tytanu, molibdenu i wanadu. Pierwiastki te moga doprowadzic do alergii, egzemy i obluzowania implantu.
-
Preparation and photocatalytic activity of B-doped titanium dioxide
PublicationOtrzymano TiO2 domieszkowany borem, aktywny w reakcjach fotodegradacji pod wpływem światła widzialnego (λ>400 nm). Fotokatalizatory otrzymano poprzez hydrolizę tytanianu(IV) izopropylu w obecności związków boru lub poprzez ucieranie ST-01 z prekursorami B i następnie kalcynację w temperaturze 450stC. Jako źródło boru zastosowano kwas borowy (0,5 i 10%wag.) lub trietylo ester kwasu borowego (0,5; 1; 5 i 10%wag.). Najwyższą aktywność...
-
Electrophoretic Deposition of Chitosan Coatings on the Porous Titanium Substrate
Publication -
Protective properties of the chromium - titanium carbonitryde composite coatings.
PublicationZbadano właściwości ochronne warstw chromowych zawierających dodatki węglika tytanu poprawiającego właściwości mechaniczne warstw. badania ditycżą roztworów kwasu siarkowego. Badania przeprpwadzono metodą spektroskopii impedamncyjnej. Wykazano ze właściwosci ochronne warswt są lepsze dzięki sdyspergowanym cząstkowm węglika tytanu.
-
Photocatalytic degradation using nitrogen-modified titanium dioxide
PublicationPrzepływowy reaktor z wypełnieniem został zastosowany do przeprowadzenia fotodegradacji 4-chlorofenolu za pomocą światła widzialnego. Fotokatalizator w postaci tlenku tytanu(IV) modyfikowanego azotem, został naniesiony na powierzchnię kulek szklanych. Źródło światła widzialnego stanowiła 8W lampa fluorescencyjna. Powietrze było w sposób ciągły przepuszczane przez zawartość reaktora.
-
Gas‐Phase Removal of Indoor Volatile Organic Compounds and Airborne Microorganisms Over Mono‐ and Bimetal‐Modified (Pt, Cu, Ag) Titanium(IV) Oxide Nanocomposites
PublicationThe photocatalytic deactivation of volatile organic compounds and mold fungi using TiO2 modified with mono‐ and bimetallic (Pt, Cu, Ag) particles is reported in this study. The mono‐ and bimetal‐modified (Pt, Cu, Ag) titanium(IV) oxide photocatalysts were prepared by chemical reduction method and characterized using XRD, XPS, DR/UV‐Vis, BET and TEM analysis. The effect of incident light, type and content of mono‐ and bimetallic...
-
Topography of iron-phosphate glasses doped with niobium and titanium tested by confocal microscope
Open Research DataThe topography of phosphate-iron glasses containing niobium and titanium were investigated with the use of confocal miscroscope. Glass samples of the composition of 35P2O5-30Fe2O3-35Nb2O5, 35P2O5-30Fe2O3-27.5Nb2O5-7.5TiO2 and 35P2O5-30Fe2O3-20Nb2O5-15TiO2 (in %mol) were prepared by the conventional melt quenching technique. Appropriate amounts of reagents...
-
Tracking of the Multimodal Ordering Process in FePd Alloy
Publication -
Phase investigations of copper based CuZn38Al2MnFe alloy
PublicationW pracy przedstawiono analizę fazową mosiądzu CuZn38Al2MnFe. Wykazano, że obecność fazy Fe4Mn77Si19 powoduje kruchość stopu w teście zginania próbek.
-
Elasto-viscoplastic properties of AA2017 aluminium alloy
PublicationArtykuł opisuje procedurę identyfikacji parmetrów materiałowych dla sprężysto-lepkoplastycznego modelu Bodnera-Partoma. Prezentowane są symulacje numeryczne testów jednoosiowego rozciągania z różnymi prędkościmi odkształcenia, które porównane są z wynikami eksperymantalnymi.
-
Internal friction in FePd alloy during ordering
PublicationStwierdzono występowanie wysokiego poziomu tarcia wewnętrznego w zahartowanym stopie FePd (50% at. Pd). Zbadano proces uporządkowania atomowego w korelacji ze zmianami tarcia wewnętrznego defektu modułu i relaksacji magnetycznej stopu porządkującego się podczas nagrzewania do 900 K. Zaobserwowano efekt prędkości nagrzewania na punkt Curie.
-
Induction Assisted Hybrid Friction Stir Welding of Dissimilar Materials AA5052 Aluminium Alloy and X12Cr13 Stainless Steel
PublicationThis research aimed to study the induction in-situ heated hybrid friction stir welding (IAFSW) method to join AA5052 aluminium alloy with X12Cr13 stainless steel (SS) to enhance joint strength. The potency of this method on the mechanical properties and microstructural characterizations were also investigated. The results show that the transverse tensile strength gained was 94% of the AA5052 base metal that is 229.5 MPa. This superior...
-
Effect of underwater friction stir welding parameters on AA5754 alloy joints: experimental studies
PublicationThe water as a welding environment may generate serious technological and metallurgical problems but in certain cases, the physicochemical properties of water can be used effectively, e.g., to impart the specific properties of welded materials. The purpose of the work was verification of effectiveness of the water cooling of aluminium alloy AA5754 for various sets of technological parameters of underwater friction stir welding...
-
Pressure effects on the electronic structure and superconductivity of (TaNb)0.67(HfZrTi)0.33 high entropy alloy
PublicationEffects of pressure on the electronic structure, electron-phonon interaction, and superconductivity of the high entropy alloy ( TaNb ) 0.67 ( HfZrTi ) 0.33 are studied in the pressure range 0–100 GPa. The electronic structure is calculated using the Korringa-Kohn-Rostoker method with the coherent potential approximation. Effects of pressure on the lattice dynamics are simulated using the Debye-Grüneisen model and the Grüneisen...
-
The Influence of Tool Shape and Process Parameters on the Mechanical Properties of AW-3004 Aluminium Alloy Friction Stir Welded Joints
PublicationThe purpose of the following study was to compare the effect of the shape of a tool onthe joint and to obtain the values of Friction Stir Welding (FSW) parameters that provide the bestpossible joint quality. The material used was an aluminium alloy, EN AW-3004 (AlMn1Mg1). To theauthors’ best knowledge, no investigations of this alloy during FSW have been presented earlier. Fivebutt joints were made with a self-developed, cylindrical,...
-
The effect of cobalt addition on the corrosion behavior of near equiatomic NiTi shape memory alloy in normal saline solution, impedance and microscopic studies
Open Research DataThe electrochemical and corrosion (uniform and localized) behavior of a binary Ni52Ti48 shape memory alloy (SMA) and two ternary Ni52Ti48-xCox (x = 1.5 and 4.0 wt.%) SMAs were studied. Measurements were conducted in 0.9% NaCl solution at 37 oC. This dataset contains the results of electrochemical impedance spectroscopy (EIS) studies done on daily basis...
-
The influence of welding heat input on the quality and properties of high strength low-alloy dissimilar steel butt joints
PublicationThe paper presents the results of non-destructive and destructive tests of dissimilar highstrength low-alloy S460ML and S460N steel butt joints. These steels are characterized by similar mechanical properties, but their carbon equivalent CeIIW values are much different. The joints were made using different values of heat input for each welding bead. They were tested by non-destructive methods: visual, penetrant, radiographic and...
-
Microstructure and Properties of Electroless Ni-P/Si3N4 Nanocomposite Coatings Deposited on the AW-7075 Aluminum Alloy
PublicationThe article presents the results of mechanical and tribological tests of Ni-P/Si3N4 nanocomposite coatings deposited on the AW-7075 aluminum alloy using the chemical reduction method. The influence of the chemical composition on the Vickers microhardness determined by the DSI method was examined. The nanocomposite layers were made of Si3N4 silicon nitride in a polydisperse powder with a particle size ranging from 20 to 25 nm. The...
-
Synthesis of Titanium Dioxide via Surfactant-Assisted Microwave Method for Photocatalytic and Dye-Sensitized Solar Cells Applications
PublicationIn this study, titania nanoparticles were obtained using the microwave-assisted technique. Moreover, different surfactants (PEG (Mn = 400), Pluronic P123 and Triton X−100) were used during the synthesis in order to determine their impact on the crystallinity and morphology of the final products. Subsequently, techniques such as XRD, SEM and TEM (performed in high contrast and high-resolution mode), diffuse reflectance spectroscopy...
-
The Effect of Sodium Tetrafluoroborate on the Properties of Conversion Coatings Formed on the AZ91D Magnesium Alloy by Plasma Electrolytic Oxidation
PublicationMagnesium and its alloys are widely used in many areas because of their light weight, excellent dimensional stability, and high strength-to-weight ratio. However, the material exhibits poor wear and corrosion resistance, which limits its use. Plasma electrolytic oxidation (PEO) is an effective surface modification method for producing ceramic oxide layers on Mg and their alloys. The influence of the additions of sodium tetrafluoroborate...
-
Optimized photodegradation of palm oil agroindustry waste effluent using multivalent manganese–modified black titanium dioxide
PublicationThis article presents a methodological approach to use manganese (Mn3+Mn7+)-modified black titanium dioxide (Mn/BTiO2) as a photocatalyst to optimize and improve visible-light-driven photodegradation of treated agro-industrial effluent (TPOME). A modified wet chemical process was used to prepare BTiO2. The BTiO2 was then wet impregnated with Mn and calcined at 300 °C for 1 h to produce Mn/BTiO2. The activity of Mn/BTiO2 was investigated...
-
The corrosion studies of 3,4,5-trihydroxybenzoic acid as an effective corrosion inhibitor of low alloy steel
Open Research DataThe dataset contains the electrochemical studies evaluating if gallic acid is a corrosion inhibitor for low alloy steel. Three measurements were carried out each case; corrosion potential (label ecorr), electrochemical impedance spectroscopy (label eis) and cyclic polarization (label cp). The measurements were carried out in sodium chloride, acidified...
-
Thermally tuneable optical and electrochemical properties of Au-Cu nanomosaic formed over the host titanium dimples
PublicationAu-Cu nanostructures offer unique optical and catalytic properties unlike the monometallic ones resulting from the specific interaction. Among others, they have the ability to exhibit surface plasmon resonance, electrochemical activity towards the oxygen and hydrogen evolution reaction (OER, HER) as well as improved photoresponse in relation to monometalic but those properties depend highly on the substrate where bimetallic structures...
-
Modification of titanium dioxide with platinum ions and clusters: application in photocatalysis
PublicationW celu polepszenia właściwości fotokatalitycznych, TiO2 (komercyjny-P25 oraz syntezowany metoda zol-żel) był domieszkowany za pomocą jonów lub klasterów [Pt3(CO)6]62- platyny. Własności fizyczne fotokatalizatorów były badane za pomocą elektronowego mikroskopu transmisyjnego (TEM), dyfraktometru rentgenowskiego (XRD) oraz analizatora powierzchni właściwej (BET). Dyfuzyjna spektrometria odbiciowa (DRS) została zastosowana w celu...
-
Photocatalytic activity and surface properties of carbon-doped titanium dioxide
PublicationTiO2 domieszkowany węglem otrzymano poprzez hydrolizę izopropanolanu tytanu(IV) i kalcynację w 350ºC w atmosferze powietrza przez 2h. Przeprowadzone badania wykazały, że fenol (0.21 mM) jest efektywnie degradowany w fazie wodnej, w obecności otrzymanego fotokatalizatora oraz światła z zakresu widzialnego (λ>400 nm). Pole powierzchni właściwej otrzymanego C-TiO2 wynosiło około 127 m2/g, fotokatalizator absorbuje światło z zakresu...
-
Environmental degradation of titanium biomaterials: mechanisms, effects, testing and evaluation
PublicationPrzedyskutowano możliwe przyczyny oraz mechanizmy degradacji biomateriałów tytanowych, używanych jako długoterminowe implanty stawów. Dokonano przeglądu wpływu impalntów metalicznych w ludzkim ciele. Przedstawiono bieżące procedury badania oraz ich wady. Zaproponowano procedurę oszacowania biomateriałów na implanty.
-
Physicochemical and photocatalytic characterization of mesoporous carbon/titanium dioxide spheres
Publication -
Anodized multi – component titanium alloys carrying antibacterial features
Publication -
Optimalization of titanium acaffold design using fuzzy reasoning approach
PublicationOpracowano metodę wnioskowania rozmytego do oszacowania geometrii scaffoldu Ti6Al4V, otrzymanego przy użyciu metody metalurgii proszków. Zaproponowana metoda umożliwia oszacowanie i optymalizację architektury scaffoldu poprzez dobór odpowiednich parametrów procesu. Zaprojektowano i przeprowadzono symulację działania sterownika rozmytego (FLC) za pomocą oprogramowania Matlab.
-
Modification of titanium dioxide towards photocatalytic activity in visible light
Publication.
-
Preparation and photocatalytic activity of iron-modified titanium dioxide photocatalysts
PublicationTiO2 modyfikowany żelazem otrzymano dwiema metodami: metodą zol-żel oraz metodą impregnacji powierzchniowej. Fotokatalizatory kalcynowano w temperaturze 400C. Jako matrycę TiO2 zastosowano komercyjnie dostępne proszki ditlenku tytanu: P25 (Evonik, Niemcy, 50m2/g) oraz ST-01 (Ishihara Sangyo, Japonia, 300m2/g). Charakterystyka otrzymanych fotokatalizatorów obejmowała wyznaczenie właściwości absorpcyjnych, powierzchni właściwej BET...
-
Cyclic Behavior of Masonry Shear Walls Retrofitted with Engineered Cementitious Composite and Pseudoelastic Shape Memory Alloy
PublicationThe behavior of masonry shear walls reinforced with pseudoelastic Ni–Ti shape memory alloy (SMA) strips and engineered cementitious composite (ECC) sheets is the main focus of this paper. The walls were subjected to quasi-static cyclic in-plane loads and evaluated by using Abaqus. Eight cases of strengthening of masonry walls were investigated. Three masonry walls were strengthened with different thicknesses of ECC sheets using...
-
High-Temperature Tensile Behaviour of GTAW Joints of P92 Steel and Alloy 617 for Two Different Fillers
PublicationThis study explores the high-temperature (HT) tensile rupture characteristics of a dissimilar gas-tungsten-arc-welded (GTAW) joint between P92 steel and Alloy 617, fabricated using ER62SB9 and ERNiCrCoMo-1 fillers. The high-temperature tensile tests were performed at elevated temperatures of 550 ◦C and 650 ◦C. An optical microscope (OM) and a field emission scanning electron microscope (FESEM) were utilized to characterize the...
-
Titanium lanthanum three oxides decorated magnetic graphene oxide for adsorption of lead ions from aqueous media
PublicationThe current study presents a viable and straightforward method for synthesizing titanium lanthanum three oxide nanoparticles (TiLa) and their decoration onto the ferrous graphene oxide sheets to produce FeGO-TiLa as efficient magnetic adsorbent. Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and vibration sample magnetometer (VSM) were used to evaluate...
-
Underwater robot actuated by shape memory alloy wires
PublicationW pracy przedstawiono koncepcję projektu robota podwodnego z napędem wykorzystującym materiały SMA ze stopów z pamięcią kształtu. Rozpatrywany układ ma budowę modułową złożoną z segmentów na podobieństwo do anatomicznej budowy dżdżownicy. Pojedyńczy segment składa się z dwóch okrągłych tarcz, pomiędzy którymi umieszczono balon wypełniony wodą. Wielkość balonu jest dopasowana w taki sposób do rozmiarów tarcz oraz długości sprężyn...
-
Influence of the heat treatment on corrosion characteristics of the Superston alloy
PublicationW artykule przedstawiono wpływ hartowania i odpuszczania na twardość i właściwości korozyjne stopu Superston, stosowanego na śruby okrętowe. Stwierdzono, iż hartowanie z temperatury 900 st.C i odpuszczanie w temperaturze 550 st.C znacząco podwyższa odporność na korozję stopu Superston w 3% roztworze NaCl w porownaniu ze stanem odlanym.
-
EXPERIMENTAL EVALUATION OF THE EMISSIVITY OF A NITI SHAPE MEMORY ALLOY
Publication -
Special Issue “Corrosion Resistance of Alloy and Coating Materials”
Publication -
Microstructure and corrosion properties of the laser treated SUPERSTON alloy
PublicationPrzedstwiono wyniki laserowego nadtapiania powierzchni stopu SUPERSTON w warunkach kriogenicznych. Zaprezentowano obraz powierzchni stopu po badaniach korozyjnych oraz wyniki pomiarów mikrotwardości i odporności korozyjnej.
-
High temperature corrosion resistance of porous hastelloy alloy
PublicationW pracy przedstawiono badania korozyjne stopu Hastelloy w wysokich temperaturach.
-
Biological properties of chitosan/Eudragit E 100 and chitosan/poly(4-vinylpyridine) coatings electrophoretically deposited on AgNPs-decorated titanium substrate
PublicationThe objective of the study was the determination of the response, in contact with human osteoblast-like MG-63 cells, of electrophoretically deposited coatings composed of chitosan (CS), Eudragit E 100 (EE100), or poly(4- vinylpyridine) (P4VP) on a silver nanoparticle (AgNPs)-decorated titanium substrate. Before deposition, the substrate was coated with silver by electro-reduction of silver nitrate. The coatings deposition was carried...